COMPREHENSIVE REPAIR TO CERTAIN BLDGS OF B/R NATURE IN RS, TIPNIS AND ARJAN ENCLAVE AREA INCLUDING REPAIR OF CEILING FAN, EXHAUST FAN, PEDESTAL FAN AT AIR FORCE AREA AND REPAIR/REP OF LT UG CABLE, PAINTING OF POLES AND OTHER CONNECTED WORKS SMQ,OMQ

Amount

Dismantling unframed timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed.

Taking down chowkats or frame, n.exc 1.5 Sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frames, exe 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but n. exc 2 Sqm each complete all as specified and directed.

Refixing shutters of any description exc 1 sqm but n.exc 2 sqm each in the same opening complete as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, pillars etc stacking the serviceable bricks after removing mortar and cleaning for re-use and disposal of debris and rubbish to a distance n.exc 100m as directed by the Engr-in-Charge.

M & L for Brick work with sub class 'B' bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M & L for Brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 including provision of 2 Nos 8mm dia, TMT bar at every fourth course complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed

M & L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with liquid water proofing compound by weight of cement as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

Supply only liquid water proofing compound (ISI marked) complete all as specified and directed.

M & L for rendering 5 mm thick on fair faces of brick work or concrete surfaces as in ceiling (sunshade, chajja etc) in cement mortar 1:3, and finished the surface even and smooth without using extra cement complete all as specified and directed.

M & L for Pressed steel frames 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

M & L for Pressed steel frames 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

M & L for Pressed steel frames 75mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

M & L for 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

S & F 35 mm thick, factory made, glazed/skeleton shutters with second class hard wood,open rebated and prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass, etc complete as specified and directed . Sizes of members of shutters as specified in SSR Part I, Section -8, clause 8.24 (a).

S & F 40 mm thick, Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S & F factory made solid wire gauzed PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side having one side feathered edge and other side 10mm, 90 degree bent edge & as gap insert for top rail & bottom rail, panel shall be of wire gauzed, The wire gauzed shall be wrapped on an additional square 8mm MS solid tube and this tube shall be welded to MS tube, the wire gauge shall be stretched to tighten firmly complete as per specification and drawing and as directed.

S & F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with printed sheet, complete all as specified and directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and both side Prelam PVC sheet used instead of plain colour PVC sheets. Stile and rails, feathered at edges for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of both side Prelam PVC sheet used instead of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable Prelam PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

S & F in repair Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F in repair Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S & F in repair Steel ventilators, with top hung shutter including hinges, steel peg stay complete complete all as specified and directed.

S & F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

Taking down steel window/ventilators shutter of any size and description and refixed in the same opening after minor repairs/welding and necessary minor accessories as required complete all as directed. (Note: Box type hinge, stay, handle etc shall be measured and paid sperately as supply only)

Supply only mild steel handle for steel window for left/right shutter complete all as specified and directed.

Supply only mild steel peg stay including nuts & bolts etc suitable for steel window and ventilator complete all as specified and directed.

Supply only mild steel box type hinge suitable for steel window and ventilator complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal/wooden frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

S & F 3 mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F 3 mm thick, figured glass, pin headed type, in square n.exc 0.5 Sqm in each pane complete all as specified and as directed.

S & F in reapir Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S & F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

S & F in repairs, 300 mm long, mild steel, ordinary rat tail rod pattern springs incuding roller and roller plate complete all as specifed and directed.

S & F 150 mm long, Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S & F 100 mm size, Aluminium handles, cast type, anodised complete all as specified and directed.

S & F 100mm, Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S & F 75mm, Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S & F 125 mm long, mild steel, barrel tower bolts stove enamelled black, with bright bolt complete all as specified and directed.

S & F 100 mm size, mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed.

S & F Aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clipes of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy, length of bolt of 250 mm complete all as specified and directed.

S & F mild steel bands, straps, supports or stays of rain water, ventilating pipes including bolts, hooks (stay) for large gates, hook and pintel hinges, clamps, hold fasts, wall ties,flat iron fillets for securing wire mesh, wind tie, fan hook and similar work including necessary drilling bolting or riveting etc conforming to Fe – 290 Gde E – 165 complete all as specified and as directed.

M & L for plain cement concrete 1:3:6, type C-1 (using 20mm graded stone crushed aggregate) for embedding holdfast, bed block, cills, etc including necessary form work complete all as specified and directed.

S & F 18mm thick, prelaminated wooden finish, PVC celuka board for shelves of cupboard etc including all necessary accessories and builders hardware, complete all as specified and directed.

S & F 12mm thick, prelaminated wooden finish, PVC celuka board for shelves of cupboard etc including all necessary accessories and builder hardware, complete all as specified and directed.

M & L for Extra over rates of block board or veneered particle board(18/19mm thick) for external teak wood lipping, 6mm thick fixed with nails complete all as specified and directed.

M & L for Extra over rates of block board or veneered particle board(12mm thick) for external teak wood lipping, 6mm thick fixed with nails complete all as specified and directed.

S & F ball catches with 8mm dia steel ball and brass body and striking plate including letting in and fixed complete all as specified and directed.

S & F 100mm,aluminium anodised, Hasp and staple, safety type, with hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S & F in repair 20 mm dia, curtain rod mild steel chromium plated decorative type, complete all as specified and directed.

S & F in repair mild steel chromium plated bracket for curtain of 20 mm dia, fancy type fixed to wall fixed type, complete all as specified and directed.

Demolition of un-reinforced cement concrete in any position not otherwise specifically provided for complete all as specified and directed.

M & L for cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M & L for 75 mm thick, plain cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement including joints filled with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

M & L for Plain cement concrete 1:3:6, type C-2 (using 40mm graded stone crushed aggregate) as in surface channel, drains etc complete all as specified and directed.

Extra for forming fair finished to concrete surface of drain 30cm inner girth in cement including forms, mould, mitred/stopped etc complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc, including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for glazed, coloured, ceramic, tiles of size (350mm x 250 mm/450mm x 350mm/300mmx450mm/350mmx450mm) x 6 to 7 mm thick, on vertical surfaces such as skirting, dados etc, including 10 mm thick bedding in cement mortor 1:4 and set & jointed in neat cement slurry & pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for 14-16mm thick Granite (of any type) slab machine cut, as in flooring, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S & F in repairs, stainless steel sinks made of 1 mm thick sheet with plugs, washers and wastes including bedding in ement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S & F in repairs, Stainless steel, kitchen rack of size 750x780mm as per existing design and specification as approved complete all as specified and directed.

S & F in repair Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

Taking up or down 15mm bore, Steel tubing and connections and keeping serviceable pipes in safe custody for reuse in the work after and including cleaning as directed.

Refixing of 15mm bore old serviceable steel tubing and connections in new or old position with new fittings complete to walls and ceilings or laid in floors, etc complete as directed. (Note: Serviceable pipe shall be reused as obtained from serial item No. 68 above)

Supply, laying, connection and testing, 15mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

S & F 15mm bore, concealed Steel water tubing, galvanised, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors and making good surfaces with cement morter 1:3 exc 10 cm girth, complete all as specified and directed.

M & L for 15mm bore, Lagging to pipes used in internal water supply or plumbing all round with, 25min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9842 complete all as specified and directed.

Taking up or down 20mm bore, Steel tubing and connections and keeping serviceable pipes in safe custody for reuse in the work after and including cleaning for re-fixing or removing from site, complete all as specied and directed.

Supply, laying, connection and testing, 20mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

Refixing of 20mm bore old serviceable steel tubing and connections in new or old position with new fittings complete to walls and ceilings or laid in floors, etc complete as directed. (Note: Serviceable pipe shall be reused as obtained from serial item No. 73 above)

S & F in repairs, Vitreous China wash basin, white, flat back , of size 580 x 450 mm excluding taps but including CP waste coupling, chain, plug & porcelain stopper, bracket complete all as specified and directed.

S & F in repairs, vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe etc complete including making good to disturbed surfaces of floor to match with existing specifications complete all as specified and directed.

S & F in repairs, vitreous China wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and flushing pipe, anti syphonic pipe with seat and cover complete but excluding flushing cistern & flush pipe including making good damaged/disturbed surfaces complete all as specified and directed.

S & F in repairs, vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as specified and directed.

S & F 500 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top), hoisted and fixed in position including 20mm nipple suitable for tank and 20 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) after taking down old unserviceable one as specified in SSR Part I and directed.

Cleaning and removing all scale and dirt, etc, from tanks of capapcity exc 500 & n.exc 1000 Ltrs and from mouths of circulating pipes, etc. using bleaching powder and washed with water including dismantling and reconnecting and refixing in position including writing date of cleaning with white synthetic enamel paint as "CLEANDED ON" complete all as specified and directed.

S & F PTMT Nipple, 20mm, suitable for HDPE water tank. (Minimum weight 20mm-45gms) complete all as specified and directed.

S & F in repairs, 20 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and directed.

S & F in repair PVC over head tank cover suitable for 500/1000 Litres capacity tank complete all as specified and directed.

S & F in repairs, 15mm bore, PVC connection pipe 450mm long with PTMT nuts at both ends complete all as specified and directed.

S & F in repairs, 32/40mm dia flexible PVC waste pipe for wash basin/sink etc complete all as specified and directed

S & F in repairs, 15 mm bore, pillar taps, fancy type, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S & F in repairs, 10 litre capacity, PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle including brackets complete all as specified and directed.

S & F in repairs, 15mm bore, bib taps, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repairs, 15mm bore, bib taps of PTMT, any colour high pressure, screwed for iron pipe and fixed (minimum weight 90 gms) complete all as specified and directed.

S & F in repairs, 15 mm bore, Stop valves, cast copper alloy, chromium plated with long shank and cup, concealed type, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in repair 15mm, Pillar taps of PTMT any colour high pressure screwed for iron pipe and fixed.(Minimum weight 15mm-110gms) complete all as specified and directed.

S & F in repair 15mm, Stop valve of PTMT any colour high pressure screwed for iron pipe and fixed.(Minimum weight 15mm-90gms) complete all as specified and directed.

S & F in repair 15mm, Angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms) complete all as specified and directed.

S & F in repair Waste coupling, 32/40mm, of PTMT (half or full threaded) (Minimum weight 32mm-45gms/40mm-60 gms) complete all as specified and directed.

S & F in repair Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed.

S & F in repair 125 mm Swivel shower rose of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms) with Shower arm 15 mm size, 195mm long with bend of 45 degree with flange of PTMT any colour.(Minimum weight 40gms) complete all as specified and directed.

S & F in repair 15 mm bore, two way angular stop cock, cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repair 15 mm bore, health faucet ABS body with wall hook and 1 m long SS braided rubber hose pipe with all accessories complete all as specified and directed.

S & F in repairs, plastic water closet, Seat and Cover for pedestal pan, white / black, closed pattern with flat bottom and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S & F in repairs, Toilet paper holder, stainless steel fixed to wall with screws complete all as specified and directed.

S & F 110 mm bore, PVC (SWR), Soil waste and vent pipes in any length with or without ears, with cement joints fixed to wall, etc with all necessary fixing arrangement including taking down old unserviceable pipe complete all as specified and directed.

S & F 75 mm bore, PVC (SWR), Soil, waste and vent pipes, single socketed in any length with rubber ring joints fixed to walls, etc including taking down old unserviceable pipe complete all as specified and directed.

S & F 110 mm bore, PVC (SWR) bends of any radius complete all as specified and directed.

S & F 110mm bore, PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S & F 75 mm bore, PVC (SWR) bends of any radius with access door complete all as specified and directed.

S & F 75mm bore, PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S & F in repair 75 mm bore, PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F in repair Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed.

S & F in repair 20 mm bore, gun metal globe or gate valve with iron wheel head screwed both ends for iron pipes and fixed complete all as specified and directed.

S & F in repair 40mm bore, High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

S & F in repairs, rubber door cill, width exc 30mm but n. exc 50mm, complete all as specified and directed.

M & L for preparing old decorated surfaces of walls, etc including cornices by bromming down or by steel wire brushing, scrapping down smokes soot, moulds, moss and efflorscent salt and treating oil and greasy spot and applying one coat of white wash complete all as specified and directed.

M & L for preparing old decorated surfaces of ceiling, etc by bromming down or by steel wire brushing, scrapping down smokes soot, moulds, moss and efflorscent salt and treating oil and greasy spot and applying one coat of white wash complete all as specified and directed.

M & L for preparing newly plastered surfaces of walls, etc and applying three coats of white wash complete all as specified and directed.

M & L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M & L for preparation of newly plastered external surfaces of wall, chajja, facia etc and applying two coats of water based acrylic weather proof exterior emulsion (exterior wall finish) paint over a coat of primer complete all as specified and directed.

M & L for preparation old decorated external surfaces of wall, chajja, facia etc after complete removal of existing treatment and applying two coats of water based acrylic weather proof exterior emulsion (exterior wall finish) paint complete all as specified and directed.

M & L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

M & L for preparing old decorated surfaces of wall/chajja, etc including cornices by bromming down or by steel wire brushing, scrapping down smokes soot, moulds, moss and efflorscent salt and treating oil and greasy spot and applying two coats of cement base paint complete all as specified and directed.

M & L for Complete removal of existing treatment from walls including preparation of surface complete all as specified and directed.

M & L for applying one or more coat of wall care putty to achieve a smooth surface after preparation of surface complete all as specified and directed.

M & L for preparing old decorated surfaces of wall, etc including cornices by bromming down or by steel wire brushing, scrapping down smokes soot, moulds, moss and efflorscent salt and treating oil and greasy spot and applying one coat of distemper oil emulsion complete all as specified and directed.

M & L for preparing newly plastered surfaces of walls etc and applying two coats of distemper oil emulsion over a coat of alkali resistant primer complete all as specified and directed.

M & L for Preparation of old painted steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint complete all as specified and directed.

M & L for Preparation of newly steel & iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M & L for Preparation of newly wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for Preparation of old painted wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Taking down from any position and Dismantling ceiling fan (any size/sweep/make), repair the same by cleaning, overhauling, necessary lathe work etc and taking out existing burnt out winding wire of motor and rewinding the same after proper cleaning with super enamelled copper wires as per existing gauge and turn to achieve the desired RPM, necessary insulating materials, insulating varnishing, cleaning and reassembling the ceiling fan after replacement of unserviceable minor parts such as split pin, lock nuts, rubber packing, clamp of condenser, blade nuts, rubber reel insulator, nuts bolts, plastic fan canopy etc as required for smooth functioning of the fan and Replacement of unserviceable major parts like capacitor, bearing, bush etc and testing complete on completion and re-fixing the fan in existing position including provn of twin twisted flexible copper stranded conductor wire of size 23/0.0076 Sqmm of required length complete as directed by the Engineer-in-Charge (Note : (a) Replacement of unserviceable major parts like capacitor, bearing, bush etc shall be measured and paid separately as "Supply only" under respective items of this Schedule. (b) Unit quoted rate shall deemed to be inclusive of transportation of fan to workshop from site of work and back)

All as per item No 130 above but for exhaust fan upto 450mm sweep complete all as specified and directed.

All as per item No 130 above but for exhaust fan of 230/300mm sweep complete all as specified and directed.

Dismantling of wall/pedestal fan of any sweep, repair the same by cleaning, overhauling, necessary lathe work (grinding & polishing) etc and taking out existing burnt out winding wire of motor and rewinding the same with super enamelled bare insulated copper winding wires as per existing gauge and turn to achieve desired RPM including necessary insulating materials, insulating varnishing, cleaning and reassembling the wall/pedestal fan after replacement of unserviceable minor parts such as frame nut, knob, regulator switch clamp of cendenser etc as required for smooth functioning of the fan and Replacement of unserviceable major parts like capacitor, bearing, bush etc and testing complete on completion and re-fixing the fan in existing position including provn of twin twisted flexible copper stranded conductor wire of size 23/0.0076 Sqmm of required length complete as directed by the Engineer-in-Charge (Note : (a) Replacement of unserviceable major parts like capacitor, bearing, bush etc shall be measured and paid separately as "Supply only" under respective items of this Schedule. (b) Unit quoted rate shall deemed to be inclusive of transportation of fan to workshop form MES store yard)

Taking down carefully existing ceiling fan of any size/sweep/make from it's existing position, dismantling the fan including preventive maintenance by servicing, greasing, oiling, cleaning external surfaces porperly and replacement of defective spare parts and re-assembling and refixing the same in position including testing and provn of twin twisted flexible copper stranded conductor wire of size 23/0.0076 Sqmm of required length complete as directed by the Engr-in-Charge. (Note : Cost of spare parts shall be measured and paid separately under respective items of this Schedule as "Supply only").

Taking down carefully existing exhaust fan/wall mounted fan/pedestal fan upto 450mm sweep from it's existing position, dismantling the fan including preventive maintenance by servicing, greasing, oiling, cleaning external surfaces porperly and replacement of defective spare parts and re-assembling and refixing the same in position including testing and provn of twin twisted flexible copper stranded conductor wire of size 23/0.0076 Sqmm of required length complete as directed by the Engr-in-Charge. (Note : Cost of spare parts shalll be measured and paid separately under respective items of this Schedule as "Supply only").

Supply only Ball bearing No 6201-Z complete all as directed (Make : TATA/SKF/NBC/HCH).

Supply only Ball bearing No. 6202-Z complete all as directed (Make : TATA/SKF/NBC/HCH).

Supply only Ball bearing No 6203-Z complete all as directed (Make : TATA/SKF/NBC/HCH).

Supply only Ball bearing No 6302-Z complete all as directed (Make : TATA/SKF/NBC/HCH).

Supply only Capacitor for ceiling fan of capacity 2.5 mfd (PVC body) + 5%, 220 volts, 50 Hz conforming to IS - 1709 AAPHS, temperature Max 85 degree centrigate complete all as specified and directed. (Make: NICCO, SIEMENS, EPCOS, Universal & TIBCON)

Supply only Capacitor for ceiling fan of capacity 3.15 mfd (PVC body) + 5%, 220 volts, 50 Hz conforming to IS - 1709 AAPHS, temperature Max 85 degree centrigate complete all as specified and directed. (Make: NICCO, SIEMENS, EPCOS, Universal & TIBCON)

Supply only Capacitor for ceiling fan of capacity 4 mfd (PVC body) + 5%, 220 volts, 50 Hz conforming to IS - 1709 AAPHS, temperature Max 85 degree centrigate complete all as specified and directed. (Make: NICCO, SIEMENS, EPCOS, Universal & TIBCON)

Supply only Gun metal bush -2 Nos with shaft rod of required size suitable for Exhast fan 230/300 mm sweep complete all as directed

Supply only Gun metal bush for suitable size of existing motor shaft for ceiling fan complete all as directed. (Make:- Orient, Usha, Ganesh ,Khaitan, MIE)

M & L for Single coat painting to ceiling fan of any sweep with 1st grade quality synthetic enamel paint by spraying, filling cavites with filler including necessary preparation of surface duly demarking fan Nos complete as specified and directed. (Note : Writing Fan No & letters shall be measured and paid separately under relevant item of this Schedule).

M & L for Single coat (spray) painting to exhaust fan of any sweep with 1st grade quality synthetic enamel paint by spraying, filling cavities with filler including necessary preparation of surface duly demarking the fan Nos complete as specified and directed. (Note : Writing Fan Nos & letter shall be measured and paid separately under relevent item of this Schedule).

M & L for Writing Nos or figures (Block, Roman, Italic or Indian) such as "MES No …." with synthetic enamel paint (1st grade quality) of tint black/white complete all as required and directed. (Max 10 Nos letter/figure & n. exc 2 cm height in each fan).

S & F in repair hanging clamp of ceiling fan made out of mild steel flat iron of suitable size including nuts, bolts, rubber reel insulator and split pin complete all as per existing specification and as directed by the Engr-in-Charge.

S & F in repairs, Stepped type, electronic fan regulator, 220 volts, flush type complete all as specified and directed. (Make: Anchor, Model No. 14502 or equivalent make as per list of manufacturer)

S & F in repair down rod (as per site requirement) made out of GI pipe, 15mm bore, medium grade for hanging ceiling fan including nuts, bolts & washer with 2 Nos rubber insulator including drilling holes as required including necessary painting with coats of synthetic enamelled paint over a coat of red oxide zinc chrome primer complete all as directed by Engr-in-Charge

M & L in replacement for Mild steel framed work such as frame for exhaust fan etc with ends of bars shouldered and/or riveted and similar work conforming to Fe.290.Gde-E-165 and necessary painting with coats of synthetic enamelled paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

S & F Rubber insulator reel type suitable for fan hook of any type including taking out old one complete all as specified and directed.

S & F in repair canopy for ceiling fan of any sweep/make/colour, complete all as per the existing specifications and as directed.

S & F in repairs, Twin core twisted, flexible copper conductor wire of size 23/0.0076 Sqmm complete all as specified and directed.

S & F in replacement of split pin and juam nut of suitable size complete all as directed.

S & F Exhaust fan, 200 mm sweep, AC, single phase complete with all accessories and electric connection including taking down existing unserviceable fan and removing to MES store yard complete all as specified and directed (Make : Havells, Model : Ventil Air DX white or equivalent model of Bajaj/Usha/ Khaitan/Orient as approved)

S & F in repair Wall fan blade PVC / Nilon heavy duty 300mm complete all as specified and directed

S & F in repair Wall fan blade PVC / Nilon heavy duty 450/600mm complete all as specified and directed

S & F in repair wall fan rotating switch with operating thread 5/6 step type complete all as specified and directed

S & F in repair modular Fan step regulator, 120W - 2 module complete all as specified and directed

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation, etc and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated material not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

Supply and laying 40mm dia, double walled corrugated(DWC) HDPE duct pipe for cable protection, conforming to IS, of approved colour with fittings complete all as specified and directed.

Supply and laying cable XLPE insulated screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 Sqmm 4 core complete all as specified and directed. (Note: Excavation and earth work shall be measured and paid seperately)

Dismantling of existing unserviceable outdoor type feeder pillar box and removing from site of work and supply, install, commissioning and testing cubical type LT distribution pillar, 415 Volts, 50 Hz AC supply, three phase and neutral, outdoor type (KIOSK) with apron of size 400mmx350mmx300mm, factory made fabricated out of MS sheet 1.6mm thick with suitable size of MS channel supports and with suitable size of angle iron legs for grouting, duly powder coated internally and externally with approved shade, rubber gasket, hinged front and back openable doors with proper locking arrangements, dust and vermin proof complete including suitable size of lugs, glands and making connections comprising of the following items complete all as specified and directed:- (a) Aluminium bus bar suitable for 200 Amps capacity for 3 phase and 200 Amps for neutral support on insulators. (b) Necessary excavation and earth work, PCC type 1:3:6 type C-1 using 20mm graded crushed stone aggregate concrete of suitable size over PCC lean concrete type D-2 as required for platform to house the panel complete all as directed

M & L for Earthing complete with GI earth plate electrode 600 mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with the top edge of earth plate at depth not less than 1.5 m below ground level connected with galvanised earth strip of size 20x3mm by means of bolts, nuts, check nuts and washers protected by 40mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, with 50 mm thick Pre-cast R.C.C. (1:2:4) type B-1 cover slab (reinforced with 8 mm dia TMT bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel, wire mesh, aluminium lugs, complete in all respect and other end connected with main switch board or earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessary testing on completion inclduing taking down old one, complete all as specified and as directed by the Engineer-in-Charge.

All as per serial item No. 168 above but of suitable size of distribution pillar to accomodate following fittings and fixtures including taking down/dismantling of existing unserviceable distrubution pillar with complete fittings complete all as specified and directed :- (a) MCCB, 4 pole, 160Amps, 16KA, incoming -01 No. (Make: Legrand Cat No. 4200 17 or equivalent as per list of manufacturers) (b) MCCB, 4 pole, 125Amps, 16KA, outgoing -01 No. (Make: Legrand Cat No. 4200 16 or equivalent as per list of manufacturers) (c) MCCB, 4 pole, 63Amps, 16KA, outgoing - 02 Nos (Make: Legrand Cat No. 4200 13 or equivalent as per list of manufacturers) (d) MCB, SPN, 63Amps, 10KA outgoing - 03 Nos (Make: Legrand Cat No. 4086 20 or equivalent as per list of manufacturers) (e) MCB, TPN, 63Amps, 10KA outgoing - 01 No (Make: Legrand Cat No. 4086 83 or equivalent as per list of manufacturers) (f) Aluminium bus bar suitable for 300 Amps capacity supported on insulators - 04 Nos (g) Necessary excavation and earth work, PCC type C-2 concrete of suitable size over PCC lean concrete type D-2 as required for platform to house the panel complete all as directed

All as per serial item No. 168 above but of suitable size of distribution pillar to accomodate following fittings and fixtures including taking down/dismantling of existing unserviceable distrubution pillar with complete fittings complete all as specified and directed :- (a) MCCB, 4 pole, 125Amps, 16KA, incoming -01 No. (Make: Legrand Cat No. 4200 16 or equivalent as per list of manufacturers) (b) MCCB, 4 pole, 100Amps, 16KA, outgoing -01 No. (Make: Legrand Cat No. 4200 15 or equivalent as per list of manufacturers) (c) MCCB, 4 pole, 63Amps, 16KA, outgoing - 03 Nos (Make: Legrand Cat No. 4200 13 or equivalent as per list of manufacturers) (d) MCB, SPN, 63Amps, 10KA outgoing - 03 Nos (Make: Legrand Cat No. 4086 20 or equivalent as per list of manufacturers) (e) Aluminium bus bar suitable for 300 Amps capacity supported on insulators - 04 Nos (f) Necessary excavation and earth work, PCC type C-2 concrete of suitable size over PCC lean concrete type D-2 as required for platform to house the panel complete all as directed

All as per serial item No. 168 above but of suitable size of distribution pillar to accomodate following fittings and fixtures including taking down/dismantling of existing unserviceable distrubution pillar with complete fittings complete all as specified and directed :- (a) MCCB, 4 pole, 125Amps, 16KA, incoming -01 No. (Make: Legrand Cat No. 4200 16 or equivalent as per list of manufacturers) (b) MCCB, 4 pole, 100Amps, 16KA, incoming -02 Nos. (Make: Legrand Cat No. 4200 15 or equivalent as per list of manufacturers) (c) MCCB, 4 pole, 63Amps, 16KA, incoming - 02 Nos (Make: Legrand Cat No. 4200 13 or equivalent as per list of manufacturers) (d) MCB, SPN, 63Amps, 10KA outgoing - 02 Nos (Make: Legrand Cat No. 4086 20 or equivalent as per list of manufacturers) (e) Aluminium bus bar suitable for 300 Amps capacity supported on insulators - 04 Nos (f) Necessary excavation and earth work, PCC type C-2 concrete of suitable size over PCC lean concrete type D-2 as required for platform to house the panel complete all as directed

M & L for Preparation of old painted surface above the planting depth/PCC coping of steel tubular LT pole upto 11.00 metre long including MS clamps, cable protection pipe, bracket fitted with steet light fittings etc by scraping with steel wire brush and applying two coats of aluminium paint to external surface of poles, MS cross arms, MS clamp, cable protection pipe etc to give even shade including Zebra colour of painting upto 2.1 m height from the top of coping/bottom of pole as per site condition and numbering of poles complete all as specified and as directed by the Engr-in-Charge.(Note : Zebra colour shall be applied by synthetic enamel paint of black/yellow colour as approved in alternate layer of 30 cm height of each layer).

M & L for preparation of old steel surfaces of any description, over 10 cm in width or girth, not otherwise described after complete removal of existing treatment and applying two coats of synthetic enamel paint over a coat of red oxide zine chrome primer complete all as specified and directed.

S & F in repairs, three core twisted, flexible copper conductor wire of size 1.0 Sqmm for connection complete all as specified and directed.

M & L for making hole by gas flame of appropriate size in street light steel pole (02 Nos per pole) for passing the connection wire etc from junction box to street light complete all as specified and directed.

S & F in repairs MCCB, 4 pole, 100Amps, 16KA, thermal magnetic complete all as specified and directed. (Make: Legrand Cat No. 4200 15 or equivalent as per list of manufacturers)

S & F in repairs MCCB, 4 pole, 160Amps, 16KA, thermal magnetic complete all as specified and directed. (Make: Legrand Cat No. 4200 17 or equivalent as per list of manufacturers)

S & F in repairs MCCB, 3 pole, 100Amps, 16KA, thermal magnetic complete all as specified and directed. (Make: Legrand Cat Part No. 4200 05 or equivalent as per list of manufacturers)

S & F in repairs MCCB, 3 pole, 125Amps, 16KA, thermal magnetic complete all as specified and directed. (Make: Legrand Cat No. 4200 06 or equivalent as per list of manufacturers)

S & F in repairs MCCB, 4 pole, 200Amps, 25KA, thermal magnetic complete all as specified and directed. (Make: Legrand Cat No. 4200 18 or equivalent as per list of manufacturers)

S & F in repairs MCCB, 4 pole, 250Amps, 25KA, thermal magnetic complete all as specified and directed. (Make: Legrand Cat No. 4200 19 or equivalent as per list of manufacturers)

M & L for Writing letters or figures (Block ,Roman, Italic or Indian) n. exc 5 cm height with synthetic enamel paint as in numbering of pole/feeder pillar box etc complete all as specified and directed.

M & L for servicing of LT feeder pillar box indoor/outdoor type, after disconnecting all connections like incoming, outgoing, bus bar connection, MCB/MCCB etc and replace the burnt lugs busbar connections, insulation tape to all bus bar as per colour code including checking the earth terminal etc complete all as directed by Engg in Charge. Note: An amount of Rs. 75026.00 on account of credit schedule for schedule 'A' part - II shall be deducted from the total amount of BOQ to arrive at the contract sum.

M/S I P GROUP

M/S. VINITA CONSTRUCTION

MAA TARA TRADING

SHRI D P AGARWAL

SHRI SURAJIT SIKDER

M/S BISHAL ENTERPRISES

M/S SARKAR ELECTRIC

Bidder Name

DEEP NIRMAN