Providing and Installation of furniture in Primary Health Center/Aam Aadmni Clinic at Village Chander Nagar and Gandhi Camp Batala Batala in District Gurdaspur

Amount

i) Providing & Installation of Furniture

Main chair for Doctor- Providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of 15mm and 12mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40Kg/m³ in back. The seat and back shall be upholstered with fabric tapestry 1mm thick and 300 GSM. The back and base of chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with full back support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be made black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment which provides back strength for the chair. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should be five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chairs should be injection moulded in black 30% glass filled, confirming to ANSI/BIFMA Standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 470±10 mm(W) X 460±10 mm(D) and back size shall be 460±10 mm(W) X 610±10 mm(H) from seat & overall height = 1050±10 mm.

Doctor Table- Supplying & Placing executive table with credenza unit in completely knock down conditions with an overall size1250mm X 600mm X 750mm that is to be assembled at site. The worktop shall have the size 800mm X 400mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on CRCA powder coated rectangle pipe having cross-section area 40mm X 20mm with 1.6mm thick. The table shall be clad with 1mm thick modesty panel which provide structural support for the table. It should be 1mm thick with star perforation CRCA powder coated sheet in linear shape. The understructure shall consist of loop leg and C-type leg made up of CRCA powder coated triangular shape pipe having cross-section area 53mm X 53mm X 75mm with 1.6mm thick. There shall be shoe provided at the base to avoid scratches on the floor. Side top shall be provided with an overall size 800mm X 500mm X 750mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823. It shall be supported on peg which is mounted on credenza unit. The credenza unit shall have overall size 1400mm X 575mm X 500mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. It shall have 2 box drawer, 1 filing drawer and 1 shutter. The drawer shall be operated with roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The shutter shall be operated by SS handle and concealed crank hinge. The credenza unit shall be mounted over CRCA powder coated U shape leg having cross-section area 53mm X 53mm x 75mm with 1.6mm thick. All the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Examination Table for Doctor Room - Two Section Top with Fix Mattress, Powder Coated, Overall Dimension - 1830mm X 560mm x 810mm

Waiting Area chair 3 seater- Supplying & Placing three seater bench. The seat and back shall be made up of high quality cold rolled MS perforated sheet of 1.2mm thick, pressed and welded to form the shape. The seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. The armrest shall be made up of mild steel powder coated tube with 1.2mm thick. The base structure shall be supported by MS powder coated with 40-60µ (DFT). There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 440±10 mm(D) X 405±10 mm(H) from ground. Overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1765±10 mm.

Waiting Area chair 2 seater - Supplying & Placing two seater bench. The seat and back shall be made up of high quality cold rolled MS perforated sheet of 1.2mm thick, pressed and welded to form the shape. The seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. The armrest shall be made up of mild steel powder coated tube with 1.2mm thick. The base structure shall be supported by MS powder coated with 40-50µ (DFT). There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 450±10 mm(D) X 430±10 mm(H) from ground. Overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1180±10 mm.

Stool for Doctor, Pharmacist Room & in Sampling Room - Revolving Stool, SS Top, Powder Coated, Height Adjustable (510mm - 690mm).

Visitor Chair for Doctor- Providing and supplying a visitor chair with ergonomic design, user comfort & aesthetically appealing. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32Kg/m³ in back. The same shall be upholstered with crape fabric tapestry 0.6mm thick and 235 GSM. The seat and back of chair shall be supplied with polypropylene beam on edges and the backrest shall be made by keeping the natural curvature of the spine. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine. The armrest shall be made of black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. The frame structure shall be cantilever support type made up of MS CRCA powder coated round pipe of Dia. 25.4mm with 1.6mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor . The seat size shall be 480±10 mm(W) X 450±10 mm(D) and back size shall be 480±10 mm(W) X 400±10 mm(H) from seat & overall height = 820±10mm, overall depth = 600±10 mm.

Table for Pharmacist - Supplying & Placing executive table with credenza unit in completely knock down conditions with an overall siz that is to be assembled at site. The worktop shall have Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on CRCA powder coated rectangle pipe having cross-section The table shall be clad with 1mm thick modesty panel which provide structural support for the table. It should be 1mm thick with star perforation CRCA powder coated sheet in linear shape. The understructure shall consist of loop leg and C-type leg made up of CRCA powder coated triangular shape pipe having. There shall be shoe provided at the base to avoid scratches on the floor. It shall be supported on peg which is mounted on credenza unit. The credenza unit shall have overall size 1400mm X 575mm X 500mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. It shall have 2 box drawer, 1 filing drawer and 1 shutter. The drawer shall be operated with roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The shutter shall be operated by SS handle and concealed crank hinge. The credenza unit shall be mounted over CRCA powder coated U shape leg having cross-section area 53mm X 53mm x 75mm with 1.6mm thick. All the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Short Storage for Medicine in Pharmacy - Supplying & placing storage unit with an overall size 900mm X 4500mm X 750mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top of the shutter shall be 25mm thick and all other profile i.e. side, back, shutter, skirting shall be 18mm thick and the edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The storage shall have 2 nos. of adjustable shelf and 4 nos. of sliding shutters shall be provided for ease of opening. The sliding shutter shall be operated on sliding rail track and SS handle as well as push lock mechanism. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the bottom to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380.

Big Storage for Medicine - Providing, supplying and placing steel almirah. The overall size of the Almirah shall be 915mm (W) X 485mm (D) X 1980mm (H). The Almirah shall be supplied with 2 nos. of glass doors with 4 nos. of adjustable shelves i.e. 5 loading compartments. The glass used shall be 4mm thick clear. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity of each shelf shall be 40 Kg maximum. Each rack shall be provided with stiffener at bottom for strength. The entire body panel and shelf shall be made of high yield strength 0.8mm thick and door 1mm thick CRCA sheet of grade ‘D’ confirming to IS: 513. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40-50µ thick.

Chair for Receptionist and Pharmacist - Supplying and placing ergonomically designed, comfortable & aesthetically appealing Mid back chair. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 50mm thick having density 40kg/m³ and 25mm thick having density 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest of the chair shall be made by keeping the natural curvature of the spine. Moulded PP arm shall be used with cushion and leatherite upholstery. For seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suite them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged made up of injection moulded in 30% glass filled black nylon having pitch circle Dia. 700 mm fitted with 5 nos. twin wheel castors, the castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 515±10mm(W) X 490±10mm(D) and back size shall be 510±10 (W) X 510±10mm(H) from seat & overall height = 945±10mm.

Partition in Doctor Room for Examiner :- Provision for providing & installation of 3 fold screen MS frame with Curtain overall dimension 1675mm H x 2450mm L around Examination Table

Reception Table- Supplying & Placing executive table with credenza unit in completely knock down conditions with an overall size5'-6''x2'-0''/2'-6''x1'x6''. that is to be assembled at site. The worktop shall have the size 800mm X 400mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on CRCA powder coated rectangle pipe having cross-section area 40mm X 20mm with 1.6mm thick. The table shall be clad with 1mm thick modesty panel which provide structural support for the table. It should be 1mm thick with star perforation CRCA powder coated sheet in linear shape. The understructure shall consist of loop leg and C-type leg made up of CRCA powder coated triangular shape pipe having cross-section area 53mm X 53mm X 75mm with 1.6mm thick. There shall be shoe provided at the base to avoid scratches on the floor. Side top shall be provided with an overall size 800mm X 500mm X 750mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823. It shall be supported on peg which is mounted on credenza unit. The credenza unit shall have overall size 1400mm X 575mm X 500mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. It shall have 2 box drawer, 1 filing drawer and 1 shutter. The drawer shall be operated with roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The shutter shall be operated by SS handle and concealed crank hinge. The credenza unit shall be mounted over CRCA powder coated U shape leg having cross-section area 53mm X 53mm x 75mm with 1.6mm thick. All the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Steeps for Examination Tablein Doctor Room - Two Section Top with Fix Mattress, Powder Coated, Overall

PROMARK TECHSOLUTIONS PVT LTD