SPECIAL REPAIR TO NCs (E) AND DSC ACCN AT AF STATION PALAM UNDER GE(AF) PALAM DELHI CANTT-10

Amount

B/R PORTION Dismantling existing roof tiles/roof treatment including Roof plaster of any thickness and removing debries from sites to out of MoD land complete all as specified and directed by Engr-in charge. Note : All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

Demolition of Mud in roofs of any thickness including plastering leeping (whether full thickness removed or only a part thereof) and removing debries from sites to out of MoD land complete all as specified and directed by Engr-in charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

Cleaning top surfaces by brooming, wire brushing, removing grass, raking out joints to receive plaster/ PCC and removing debris, grass etc. removing debries from sites to out of MoD land complete all as specified and directed by Engr-in charge. Note: 1. All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates. 2. Plaster shall be measured and paid separately under appropriate item of Sch ‘A’. 3.Quoted Rate for this item shall be inclusive of disconnect, fitment at water tank or solar heater etc and refixing in the same position after completing roof treatment.

M&L for PCC 1:2:4 type B-1 (using 20mm grade stone aggregate) as in coving/coping, benching, bed block for water tank, roof padding window cills etc complete all as specified and directed by Engr-in charge. Note : All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates

M&L for applying 3.00mm thick APP based polymer membrane on accessible roof as per manufacturer instruction, over 85/25 industrial bituminous coat @ 1.20Kg/Sqm over bituminous primer @ 0.30 Ltr/Sqm on newly plastered clean and dry roof surface including sealing of joint by torch application complete all as specified and directed by Engr-in charge. Note: 1. All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

M&L for cement concrete tiles 25 cm X25 cm X 20 mm thick machine pressed set ,jointed and pointed in neat cement slurry in floor with grey cement and no pigment over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed by Engr-in charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water, etc. removing debries from sites to out of MoD land complete all as specified and directed by Engr-in charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

M&L for Rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces, making even and fair without using extra cement complete all as specified and directed by Engr-in charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

M&L for Rendering 10 mm thick in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces, making even and fair without using extra cement complete all as specified and directed by Engr-in charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

M&L for PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in coving in chajja / projection coping, window cills and angle grouting etc complete all as specified and as directed by Engr-in-charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

M&L for Rendering 10 mm thick in cement mortar 1:4 on concrete ceiling surfaces of rooms and balcony making even and smooth without using extra cement complete all as specified and directed by Engr-in charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

M&L for preparation of newly plastered surfaces of walls, applying complete one coat of primer exterior grade and applying two coats of exterior emulsion paint 100% acrylic of approved white or coloured complete all as specified & directed by Engineer-in-Charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

M&L for preparation of newly plastered surfaces of walls, applying complete all over surface wall care putty avg 1mm thick and applying two coats oil emulsion distemper white or coloured over a coat of primer complete all as specified & directed by Engineer-in-Charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

M&L for preparation for newly plastered surface of ceiling and applying two coat of oil bound distemper complete all as specified and as directed by Engineer-In-Charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

M&L for complete removal of existing treatment from old decorated plastered surfaces of walls by removal of nails etc. & filling cracks/hole with putty, and applying on complete all over surfaces wall care putty avg 1mm thick and applying two coats of oil bound distemper white or coloured by roller over a coat of primer complete all as specified & directed by Engineer-in-Charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

M&L for complete removal of existing treatment from old decorated plastered surfaces of walls by removal of nails etc & filling cracks/hole with putty, and applying one coat of primer and applying two coat of exterior emulsion paint 100% acrylic of approved white or coloured complete all as specified & directed by Engineer-in-Charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

M&L for preparation of plastered or un plastered old decorated surfaces of ceiling filling cracks/hole by applying wall care putty as required and applying one coat oil emulsion distemper white or coloured complete all as specified & directed by Engineer-in-Charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

M&L for preparation of old painted surfaces of wood & wood based surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of old painted surfaces of steel & steel based surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation old decorated surfaces of walls and cornices, spoiled by smoke soot, moulds, moss and efflorescent salts and trading oily and greasy spots by scraping and washing with water and applying one coat of cement base paint complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs, 110mm dia PVC (SWR) pipes, double socketed in any length with rubber ring joints fixed to walls and taking down of unserviceable PVC pipe complete all as specified and as directed. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

S&F in repair 110mm dia PVC SWR Tee / Bend with access door cap,if required complete all as specified and directed. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

S&F Stack Clamp GI Channel with 10mm dia U clamp with nut bolt and washer suitable for 110/100 mm dia pipe and fixed to wall complete all as specified and as directed. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

S&F Galvanised Steel Water Tubing 50mm Bore (dia), ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other situation including Taking up or down unserviceable Steel Water Tubing with Fittings and Connections, etc. complete all as specified and as directed. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

S&F Galvanised Steel Water Tubing 32mm Bore (dia), ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other situation including Taking up or down unserviceable Steel Water Tubing with Fittings and Connections, etc. complete all as specified and as directed. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

S&F Galvanised Steel Water Tubing 25mm Bore (dia), ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other situation including Taking up or down unserviceable Steel Water Tubing with Fittings and Connections, etc. complete all as specified and as directed. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

S&F Galvanised Steel Water Tubing 20mm Bore (dia), ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other situation including Taking up or down unserviceable Steel Water Tubing with Fittings and Connections, etc. complete all as specified and as directed. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

S&F Galvanised Steel Water Tubing 15mm Bore (dia), ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other situation including Taking up or down unserviceable Steel Water Tubing with Fittings and Connections, etc. complete all as specified and as directed. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

S&F for taking down & refixing old steel tubing & connections in new or old position (Walls, ceiling, floors, etc.) of 50mm Bore (dia), in any situation including replacement of old unserviceable fittings such as socket, elbow, tee, union etc. complete all as specified and as directed. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

S&F for taking down & refixing old steel tubing & connections in new or old position (Walls, ceiling, floors, etc.) of 32mm Bore (dia), in any situation including replacement of old unserviceable fittings such as socket, elbow, tee, union etc. complete all as specified and as directed. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

S&F for taking down & refixing old steel tubing & connections in new or old position (Walls, ceiling, floors, etc.) of 25mm Bore (dia), in any situation including replacement of old unserviceable fittings such as socket, elbow, tee, union etc. complete all as specified and as directed. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

S&F for taking down & refixing old steel tubing & connections in new or old position (Walls, ceiling, floors, etc.) of 20mm Bore (dia), in any situation including replacement of old unserviceable fittings such as socket, elbow, tee, union etc. complete all as specified and as directed. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

S&F for taking down & refixing old steel tubing & connections in new or old position (Walls, ceiling, floors, etc.) of 15mm Bore (dia), in any situation including replacement of old unserviceable fittings such as socket, elbow, tee, union etc. complete all as specified and as directed. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

S&F 100mm dia sand cast iron soil, waste and vent pipes in any length with or without ears, with cement joint and necessary fittings such as bend , branch piece ,tee with or without excess door cap as required fixed to walls or laid in floors as required including taking down old unserviceable pipes complete all as specified and directed by Engr-in charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

S&F 75mm dia sand cast iron soil, waste and vent pipes in any length with or without ears, with cement joint and necessary fittings such as bend , branch piece ,tee with or without excess door cap as required fixed to walls or laid in floors as required including taking down old unserviceable pipes complete all as specified and directed by Engr-in charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to the stores and rubbish off out of MoD land complete all as specified and directed by Engr-in charge.

M&L Cement Concrete 1:2:4 ,Type B-1 (20mm Graded Stone Aggregate) 25 mm thick, as in Floors, etc., and finished the Cement Concrete Surfaces Even and fair with using Extra Cement, complete all as specified and as directed.

M&L Non–Skid Ceramic white/Coloured Tiles, of 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, Laid on floor, over and including 15mm thick screed bed in cement mortar 1:4, Laid and Jointed in Neat Cement Slurry and pointed in White Cement with pigment to match the shade of the Tiles, complete all as specified and as directed.

M&L for Glazed Ceramic white/Coloured Tiles of size 200X300X7 mm to 300X450X7mm to 8mm thick including highlighter , set on vertical surfaces such as Skirting, Dado, etc, over and including 10mm thick rendering in cement mortar 1:4, Set and Jointed in Neat Cement Slurry and Pointed in White Cement with pigment to match the shade of the Tiles, complete all as specified and as directed.

Demolition of brick masonry, built in cement mortar of any description complete all as specified and directed by Engineer-in-Charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

M&L for Brickwork with old size, kiln burnt subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed by Engr-in charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

Demolition of Cement Concrete (un-reinforced) of sunken floor,roofs,floors other than ground floor hacking of surfaces after cleaning with wire brush (floor and adjoining walls any description), and removing debries from sites to out of MoD land complete all as specified and directed by Engr-in charge. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

M&L for 15 mm thick cement plastering in CM 1:4 on brick/concrete surfaces of roof and parapet, sunken mixed with liquid water proofing compound, finished even and smooth without using extra cement (Including 4 Storey building) complete all as specified and as directed by Engineer-in-Charge. Note :- Water proofing compound shall be measured & paid separately.

Supply only liquid water proofing compound complete all as specified and as directed.

M&L for applying 3.00mm thick APP based polymer membrane as per manufacturer instruction, over 85/25 industrial bituminous coat @ 1.20Kg/Sqm over bituminous primer @ 0.30 Ltr/Sqm on newly plastered clean and dry sunken surface/ roof surface including sealing of joint by torch application complete all as specified & as directed by Engr-in-charge.

M&L for cement concrete type E2 1:5:10 (40mm graded crushed stone aggregate) in foundations, mass concrete and filling in sunken floor etc. complete all as specified & as directed by Engr-in-charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) area n.exc. 1.5 Sqm each complete all as specified and as directed.

All as per ser. Item no. 47 above but area exceeding 1.50 sqm but n.exc. 4 Sqm each complete all as specified and directed.

Taking down shutters only area exc 1sqm and n. exc 2 sqm each complete all as specified and as directed.

M&L for mild steel works as in grills and railing and chowkhat of Fe-410-0 or Fe 310-0, complete all as specified and as directed by Engr-in-charge

S&F PVC Solid moulded Architrave Door Frame of Size 50X47mm & more made out of min 5.0mm Coloured with Plastic Trim decorated PVC Sheet Reinforced with Mild Steel Square Tube as specified in Manufacturer’s Instructions ,complete all as specified and as directed.

S&F Factory Made PVC Solid moulded Architrave Door Shutter 25 to 30mm thick (Stiles) consisting of Frame made out of Mild Steel Tubes for Top and Bottom Rails, Mild Steel Frame shall be covered with heat moulded Plain Colour PVC 'C' Channel having a PVC Sheet Strip of 20mm width stuck inside with Solvent Cement for Stiles and Plain Colour PVC Sheet for Top Rail, Lock Rail and Bottom Rail on either Side and as Gap insert for Top Rails & Bottom Rail, Panelling of Plain Colour PVC Sheet to be fitted in the Mild Steel Frame welded/sealed to the Stiles and Rails with suitable PVC Sheet Beading and Joined together with Solvent Cement and fixing in the Frame at Site as per Specifications and Drawings, complete all as specified and as directed.

S/F 150mm long Aluminium anodised handles, cast type complete all as specified and as directed.

S&F 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

S&F Mild Steel Butt Hinges ,100mm, Medium Weight, Cold Rolled ISI Marked and fixed, complete all as specified and as directed.

S&F brass CP fancy Pillar Taps 15mm Bore, Cast Copper Alloy with Capstan Heads, screwed down high pressure with or without lettered ‘HOT’ or ‘COLD’ with long screwed Shanks and Fly-Nuts, screwed for Iron Pipe and fixed-in-repairs, complete all as specified and directed. Make :- Cat No PSP-510 of Prima/ARG-104 of Coronet or equivalent Marc/Jaguar/Cera.

S&F Fancy type two way bib tap 15mm Bore,Chromium Plated, screwed down high pressure with or without lettered ‘HOT’ or ‘COLD’ with long screwed Shanks and Fly-Nuts, screwed for Iron Pipe and fixed-in-repairs, complete all as specified and as directed. Make:- Cat No PSP-512 of Prima/ARG-207 of Coronet or equivalent of Marc/Jaguar/Cera.

S&F Angle Stop Cock 15mm Bore (dia), Chromium Plated, screwed down, screwed for Iron Pipe or for Brass Ferrule and fixed-in-repairs complete all as specified and directed. Make :- Cat No PSP-504 of Prima/ARG-404 of Coronet or Equivalent of Cera/Johnsen/Jaquar/Marc.

S&F Vitreous China Soap Dish, Single, as Approved, fixing with Brass Chromium Plated Screws including taking down unserviceable soap Dish of any description, complete as all specified and directed. Make :- Cera, Johnson, jaquar, Marc.

S&F Brass CP Health Faucet with 1.00m long tube and holder as Approved, including Taking down unserviceable Health Faucet of any description, complete as all specified and directed.

S&F SS Chromium Plated Towel Rail 900mm Long, as Approved, fixed including taking down unserviceable towel Rail of any description, complete as all specified and directed. Make :- Cera/Johnsen/jaquar/Marc.

S&F Brass CP fancy Bib Cock 15mm Bore (dia), Chromium Plated Long Body, screwed down, screwed for Iron Pipe or for Brass Ferrule and fixed-in-repairs, complete all as specified and as directed. Make :- Cera, Johnson, jaquar, Marc.

M&L for Vitreous China White Wash down Water Closet Pan (Pedestal Pattern) including Bolts, (excluding Flushing Cistern and Flushing Pipe) with white Plastic Seat cover, with Recessed Bottom closed pattern and Cover including Mild Steel Chromium Plated Aluminium Hanging Device and fixed-in-repairs, including Making Good disturbed Surfaces with Cement Mortar 1:3, complete all as specified and as directed.

M&L for Vitreous China Squatting Pan ‘ORISSA’ Pattern, size 580X440 mm White, with ‘P’ or ‘S’ Trap, Integral Foot Rest, providing Joints between Flush Pipe and Socket of WC Pan excluding Flushing Cistern and Flush Pipe, fixing with and including provision of 150mm thick Lime Concrete Bedding including Taking out unserviceable WC Pan and connected Items, complete all as specified and as directed.

S&F PVC Flushing Cistern 10 Litre capacity, Low Level Valve Less, Symphonic Action type, White, with Inlet, Ball Valve, Float and Handle including a Pair of Cast Iron Brackets duly Painted/Erecting Stand and PVC connection pipe 15mm size, PVC Flush Pipe of polythene 32mm dia for Low Level Flushing Cistern including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and fixed including taking down/out unserviceable Flushing Cistern and connected Items, complete all as specified and as directed.

S&F in repair High pressure PVC connections pipe 450mm long suitable for 15mm size with Brass CP Check nut complete all as specified and directed by Engr-in-Charge.

S&F vitreous china wash basin of size 550x400mm including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

S&F in repair chromium plated shower rose 125 mm size with CP arm fancy type fixed to 15mm bore pipe complete all as specified and directed.

S&F in repair stop cock concealed type fancy type chromium plated, screwed down, high pressure crutch or butterfly handle screwed both ends for iron pipe of 15mm bore pipe complete all as specified and directed.

S&F Bottle trap of PTMT having minimum water seal of 25mm (Minimum weight 32mm-260gms/ 40mm-270 gms) for 32 mm dia bore dia of discharge pipe complete all as specified and directed.

M&L for replacement of 75mm outlet CI floor/nahani trap with steel grating including jointing and breaking/ dismantling any type of floor and making good cement concrete to the B-1 (1:2:4) and testing after repairs and taking down existing trap etc. complete all as specified and directed by Engr-in-Charge

M&L for applying cement paste mixed with RBR compound (Roff Bond Repair) mixed in ratio as per manufacturers instructions to stop the seepage, applied in sides of Nahani trap/floor traps, W.C traps, junction of pipes, bends & similar item/joints/ junctions to eliminate the seepage also at the wall area n.exc 1.5 Sqm each complete all as specified and directed by Engr in Charge.

S&F in repairs 20mm dia 16 gauge Aluminium powder coated curtain rods including cutting and fixing complete including clamps and side knobs complete all as specified and directed by Engr-in-Charge

Hacking out old broken glass (any thickness, size, quality or description) from wooden or steel frames, glazed with putty or fixed with wooden beads complete all as directed. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

S&F 4.0mm thick sheet glass plain pane best quality fixing to Aluminium/Steel/wooden Sections as in Panel of Doors/Windows/Ventilator and Panelling Works with necessary fixing Arrangements viz Jointing Cleats, Glazing Clips, Rubber Packing, Screws, etc. or fixed with Oil Putty, as required/ordered at Site(s), complete all as specified and as directed. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

S&F 4.0mm thick Glass pane figured ,pin headed type, best quality, fixing to Aluminium/Steel Sections as in Panel of Doors/ Windows Shutters and Panelling Works with necessary fixing Arrangements viz Jointing Cleats, Glazing Clips, Rubber Packing, Screws, etc. or fixed with Oil Putty, as required/ordered at Site(s), complete all as specified and as directed. Note: All scaffolding and necessary security parameter which are required to be taken for 9 storey (G+8) bldg are deemed to be included in quoted rates.

S&F in repair for Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium/wooden/steel beads complete all as specified and directed.

M&L for 35mm thick 2nd class Factory made hard wood Plain framed ,panelled shutters (any numbers of panels) with panels of timber flat on both sides feather edged or veneered particle board medium density wood particle board with commercial face veneers, S&F to chowkhats complete all as specified and directed by Engineer-in-Charge.

S&F aluminum alloy,anodised, sliding door bolt ,300mm long with hasp, staple (bolt type) adnd fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy complete all as specified and directed.

M&L preparation of new or previously untreated surfaces of wood of any description not otherwise described width or girth and applying two coats of synthetic enamel paint over & including one coat of pink primer complete all as specified and directed.

M&L preparation of new or previously steel surfaces of any description not otherwise described width or girth and applying two coats of synthetic enamel paint over & including one coat of red oxide primer complete all as specified and directed.

S&F 35mm thick 2nd class hardwood factory made, glazed and skelton shutter, open rebated and prepared to received glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I section-8, Clause 8.24(a), fitted to chowkhats complete all as specified and directed.

S&F window /ventilator section of frame 72 x 55 mm fixed to wall or concrete surfaces with MS hold fast (30 x 5 mm section ) 150 mm long made of galvanised steel powder coated and section of shutter 47 x20 mm mullion section 72 x 50 mm (BSe steel as per 513 D quality galvanised as per IS 277 with zinc of 120 gms /sqm glazed or gauge and wire mesh to the shutter double door shutter) with total coated grill/guard bars made of square bars 10 mm dia at 150 mm c/c horizontal spacing fixed in MS flat frame (30 x 5mm ) fixed to window frame with screw including 4 to 5 mm thick steel glass 0.36 mm stainless steel wire cloth with 1.40 mm aperture necessary fitting and all builders hardware such as handle tower bolts & stay etc. complete all as specified and directed by Engineer-in-Charge. type -4000 series ref drg No - CEAF/STD -191/2014 Sheet 1/2 & 2/2 (latest revised)

M&L for 75mm thick PCC 1:3:6 Type C2 (using 40mm graded stone aggregate) as in plinth protection and Paving including finishing even and smooth without using extra cement complete all as specified and directed.

S&F in repairs brass ball valve, high pressure of brass with rod & high density plastic ball screwed for iron pipe and fixed 50 mm bore complete all as specified and directed by Engineer in charge.

M & L for removing loose, disturbed or disintegrated old concrete surfaces of RCC Tank, beam, column, lintel, slab,chaja pardi, railing etc, cleaning thoroughly exposed reinforcement, by sand blasting using suitable pump as directed by the GE, preparing exposed concrete surfaces to receive guniting, applying one coat of anti corrosive paint to the exposed reinforcement, supply and fix welded wire mesh of size 100 x 100 mm of 3 mm dia wire, weight not less than 1.37 Kg/Sqm & binding with 22 guage mild steel (annealed) binding wire to reinforcement and applying pressure guniting in cement mortar 1:3, average 30mm to 50mm thickness and thereafter rendering 10 mm thick plaster in cement mortar 1:3, mixed with water proofing compound @2% by weight of cement and finishing the surfaces even and smooth without using extra cement to match with the existing surfaces, removing the debris outside MD land including material and labour for necessary scaffolding and formwork (G+8 storeys) and safety arrangement for guniting work, complete all as specified and directed. (Note: The finish of the surfaces to be matched with the existing surface. WPC shall be measured & paid separately as supply only).

INTERNAL ELECTRIFICATION Taking down carefully unserviceable copper/aluminium point wiring (light, fan, socket or power)complete including fixture and fitting such as switches, ceiling rose lamp holder, regulators, sockets, light fittings, wooden terminal boxes, plastic laminated sheet cover, including taking down of DBs any type, meter board any type complete all as specified and directed.

M & L for Point wiring with single core PVC insulated but unsheathed 1.5 Sqmm FRLS multi-stranded copper conductor cable 1100 volts grade IS-694 marked drawn in and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked with all conduit fittings and fixing accessories in concealed wiring system including necessary cutting, chasing and making good the disturbed surface of wall including pressed steeI boxes with bakelite sheet for mounting switches, sockets, fan regulators, etc and earth wire single core PVC insulated multi-stranded copper conductor cable 1100 volts grade IS-694 marked 1.5 Sqmm FRLS cable as continuous earth wire connecting to common earth dolly complete all as specified and directed by Engr- in- Charge for following:

(a) One light point controlled by one switch one way

(b) One fan/exhaust fan point controlled by one switch.

(c) One socket outlet 5 Amp controlled by one switch on independent board

(d) One 3 pin 5 Amps socket outlet point on the same board controlled by one switch complete

All as per Srl item No. 88 here-in-before but for one power point 6 pin 15 Amps socket outlet with 2.5 Sq mm stranded copper conductor cable PVC insulated including earth wire 2.5 Sq mm copper conductor cable connected to earth dolly complete all as specified and directed.

Supply and fixing in replacement switch piano flush type 5 Amps, single pole one way complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement socket outlet 3 pin 5 Amps, flush type, complete all as specified and directed by Engr-in-Charge.

S&F in replacement switch piano flush type single pole one way15 Amps, complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in replacement socket outlet 2 in 1, 6 pin 5/15 Amps, flush type complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in replacement stepped fan regulator 300 watt, 230 volts, 50 HZ, AC complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in replacement ceiling rose, surface type, 65mm x 50mm, 3 terminal complete all as specified and as directed by Engr-in-Charge.

S&F in replacement Indoor decorative LED battens- integrated type 20 watt 4 feet white fixture with extruded aluminium body, complete with driver and all accessories internally pre wired and including connecting up with twin core copper conductor cable complete all as specified and directed by Engr-in-Charge.

S&F in replacement Decorative wall light fixture made up of Polycarbonate, suitable for 9 W LED lamp B22 base with 9W LED Bulb complete all as specified and directed by Engr-in-Charge.

S&Fin replacement, Trim Clip on LED panel round 24W 6500K unique slimmest recess cum surface panel and including providing and connecting with twin core copper conductor twisted cable and testing on completion all as specified and directed.

S&F in replacement LED bldg light highly efficient high power 60 Watt with powder coated pressure die cast Aluminium with heat resistance toughened glass lens with internally prewired incl electronic driver and connecting up with three core flexible Copper conductor 1.5 sqmm cable complete including GI pipe light grade 40mm dia bracket not less than 1.5 Mtr long and bent to a shape for fixing of street lights with necessary MS clamps, nuts, bolts etc complete all as specified and directed by Engr-in-Charge.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with blades, and frame and louvers complete all as specified and directed by Engr-in-Charge.

Supply and fix ventilator fan, plastic body AC single Phase. 230V of size 200mm sweep with, blades, and frame and louvers complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement LED bulb 9W complete all as specified and directed by Engr-in-Charge.

SHYAM ENTERPRISES

SAI SARTHI ENGINEERING & CONSTRUCTION CO.

Sumit Enterprises

M/S Parmod Johar