Construction of New Health and Wellness Center at Samarvani and Khadoli, DNH.

Amount

Providing material, Equipment and labour for Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials and disposing off the excavated stuff upto 50 Meter lead.(C) Hard Murrum complete as directed by engineer-incharge.

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful materials and disposing off the excavated stuff upto 50 Meter lead.(B) All kind of soil, Hard Murrum, Soft rock, etc

Supplying and filling in plinth with Sand and/or Unscreen Gravel under floors, including watering, ramming, consolidating and dressing complete.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm. in depth consolidating each deposited layer by ramming and watering.

Providing and laying cement concrete 1:3:6 (1-Cement : 3- coarse sand : 6- hand broken stone aggregates 40 mmnominal size) and curing complete excluding cost of formwork in (A) Foundation and Plinth

Providing and laying controlled cement concrete M.250 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in (A) Foundations, footings, Base of columns and Mass concrete.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in (C) Slabs, landing, shelves and Cantilever upto floor two level, etc complete as directed by engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in Lintels, Beams, Girders and Cantilever upto floor two level etc complete as directed by Engineer-incharge. etc complete as directed by Engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in Lintels, Beams, Girders and Cantilever above floor two level etc complete as directed by Engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding the Cost of reinforcement for reinforced concrete work in (D) Columns, Pillars, Circular, rectangular posts and struts upto floor two level. etc complete as directed by Engineer-incharge.

Providing and laying controlled cement concrete M.200 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in Lintels, Beams, Girders and Cantilever upto floor two level etc complete as directed by Engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding the cost of reinforcement for reinforced concrete work in (E) Staircases upto floor two level, etc complete as directed by engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in (C) Slabs, landing, shelves and Cantilever above floor two level, etc complete as directed by engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding the Cost of reinforcement for reinforced concrete work in (D) Columns, Pillars posts and struts above floor two level. etc complete as directed by Engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding the cost of reinforcement for reinforced concrete work in Walls above floor two level upto floor three level, etc complete as directed by engineer-incharge.

Providing TMT Primary steel Bar FE 500/500D reinforcement of for R.C.C. work including bending, binding and placing in position complete upto floor two level

Providing, laying and constructing Brick work using common brunt clay building conventional bricks having crushing strength not less than 35 kg./sq.cm. in Foundation and Plinth in cement mortar 1:5 (1 cement : 5 sand) in true line and level including curing, scaffolding, racking out the joints etc. complete as directed by engineer in charge. Plinth Masonry

Providing and applying 12mm thik (Average) premixed formulated one coat Gypsum lightweight plaster having additives and light weight aggregates as vermiculity/Perlite respectively conforming to IS:2547 (Parth -1 & II) 1976, applied on hacked / Uneven background such as bare brick/block/RCC work on walls & ceiling at all floors and locations, finished in smooth line and level ect. complete (As directed by Engineer in charge)

Providing material and labour for fixing G.I. hexagonal chickenmesh of size 20mm x 20mm of 22 gauge at junction of concrete and brick work or between different materials after making "V" grove between two different material surface and filled with rich cement mortar and @ 100mm on each side of surfaces including necessary "U" nails/ screws/ washers with cleats for fixing, overlaps, curing, scaffolding etc complete for all floors/ all levels/ all heights/ all shapes as per direction of Engineer-in-charge.

Providing, laying and constructing Aerated light weight concrete block of (Magicrete / Eracrete / Eco green) make approved quality having crushing strength not less than 35 kg/sqcm for super structure in cement mortar 1:5 ( 1 cement : 5 sand ) or chemical joint complete as directed by engineer in charge. All Floor level

Providing material and labour for fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws, with Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS :2046 Type S, including cost of adhesive of approved quality 1.0mm Thick on both face, with Providing and fixing S.S. tower bolts (barrel type) with necessary screws etc 200mm long x10mm dia, with Providing and fixing S.S. Door Aldrop with necessary screws etc. 300mm long x16mm dia, Providing and fixing S.S. Door Aldrop with necessary screws etc 250mm long x16mm dia, with Providing and fixing S.S. Pipe Handle for door 30cm size on both side of Door shutter, with Providing and fixing S.S hanging type floor door stopper with necessary screws, etc. complete as directed by Engineer in charge. All S.S Shall be ASIS 304 Grade.

Supply of 35mm thick Fiber Glass shutter with 1.5 to 2.0 mm thick fire retardent grade FRP skin in wood grain rasied panel design having extra reinforcement on sides & edges & in polish design finish. The core of the shutter is to be filled up with injected retardent grade polyurethane foam done in situ alongwith embedded wooden pieces for stiffening & also taking hinges & fintures. The whole shutter is to be water proof ,weather proof, termite proof & resistance to mild acid/alkali with Providing and fixing S.S. tower bolts (barrel type) with necessary screws etc 200mm long x10mm dia, with Providing and fixing S.S. Door Aldrop with necessary screws etc. 300mm long x16mm dia, Providing and fixing S.S. Door Aldrop with necessary screws etc 250mm long x16mm dia, with Providing and fixing S.S. Heavy Door handles with screws etc 150mm long on both side of Door shutter, with Providing and fixing S.S hanging type floor door stopper with necessary screws, etc. complete as directed by Engineer in charge. All S.S Shall be ASIS 304 Grade.

Providing and fixing extruded aluminum window having extruded aluminum Colour anodized section frame main outer size 127mm x 38.10mm x 1.35mm (of Jindal Section no:2443,@ Wt.1.384 Kg/mt),horizontal Four track member size 122.20mm x 31.75mm x 1.10mm (of Jindal Section no:8787,@ Wt. 1.205 Kg/mt),vertical member of size 122.20mm x 31.75mm x 1.50mm (of Jindal Section no:8935,@ Wt. 1.398 Kg/mt) with sliding shutters of horizontal member size 40mm x 18mm x 1.29mm (of Jindal Section no:8949 @ wt.of 0.456Kg/mt),vertical member of size 40mm x 18mm x 1.29mm (of Jindal Section no:8947 @ wt.of 0.456Kg/mt/Section 8948,@ Wt. 0.457 Kg/mt) with 5 mm thick transparent bronze colour tinted float glass/s.s mosquito net with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as per details etc complete for window.

Providing and fixing standard extruded of alluminium section of size 63 mm x 38.10 mm x 1.2 mm ( of Jindal Section No. 2434 @ wt 0.643 kg/rmt ) with colour anodized alluminium frame for ventilation with 5 mm thick frosted glass as details etc complete for ventilation

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade area of slab upto 0.50 sqm, etc complete as directed by engineer-incharge

Providing 15 mm. thick cement plaster in single coat on fair side of Brick/concrete walls for interior plastering upto floor two level and finished even and smooth in Cement mortar 1:4 [1 cement: 4 sand) including floating coat of neat cement slurry and necessary curing, scaffolding, in true line and level etc. complete as directed by Engineer in Charge

20 mm thick sand faced cement plaster on walls upto height 10 metres above ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc. complete

Providing cement vata ( 10 cm x 10 cm size ) quarter round in cement mortar 1:1 including neat cement finishing, watering etc. complete as directed by Engineer in Charge

Providing throating or plaster drip and moulding to RCC projections as directed by Engineer in Charge

Applying two coats of Birla (white cement based) or Asian (acrylic lapy- putty) or equivalent & two coats of primer of approved brand and manufacture on new wall surface to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth. Including Wall painting (two coats) with plastic emulsion paint (make of Asian,nerolac,Berger ) of approved brand and manufacture on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an required shape even shade after thoroughly brushing the surface to remove all dirt, and remains of loose powdered materials.etc complete

Providing & laying Glossy, matte or Rustic ASTERIX BEIGE or equivalent Vitrified heavy duty 9.5 mm thick tiles flooring, laid on bed of 20mm (Average) base of Cement Mortar 1:6 (1-Cement : 6 Coarse Sand) on new surface and jointed with colour cement slurry including finished with flush pointing & cleaning the surface etc. completed of any shade approved by Higher Authority of approved brands like Somani ,Rak, City, Sun Heart,Marbito etc. of approved size (60X60cm) as directed by Engineer in Charge

Prov. & laying Digital 60 x 30 cm Full Body Glossy, matte or Rustic Natural IVORY PISSARO LT Ceramic Ultima Digital 8 mm to 9 mm thick tiles ,skirting,dado laid on bed of 20mm (Average) base of Cement Mortar 1:6 (1-Cement : 6 Coarse Sand) on new surface and jointed with colour cement slurry including finished with flush pointing & cleaning the surface etc. completed of any shade approved by Higher Authority of approved brands like Somani ,Rak, City, Sun Heart,Marbito etc as directed by Engineer in Charge.

Providing and laying Mirror polished green Kota Stone Slab flooring,dedo or skirting over 20mm ( average )thick base of cement mortar 1 : 6 ( 1 cement : 6 Coarse sand ) or L.M 1:1.5 laid over and jointed with grey cement slurry including rubbing and polishing etc. complete of approved colour and shade as per the drawing provided by the architect. 25mm Thick

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing Material, Labour and equipments for Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thickjointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : including Khurra & Gola work With average thickness of 120 mm and minimum thickness at khurra as 65 mm, etc complete as directed by engineer-incharge.

Providing and fixing M.S. grills of required pattern to wooden frames of windows etc. with M.S. flats at required spacings and frame alround, square or round bars with round headed bolts and nuts or by screws (A) Plain Grill.

Providing Material, Labour and equipments for Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. etc complete as directed by engineer-incharge. With Brick work using Conventional common burnt clay building brick having crushing strength not less than 35 kg/sq.cm etc complete as directed by engineer-incharge.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [B] 20 mm. (Make: Astral, Prince, Supreme, Finolex)*

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [C] 25 mm.

Providing laying and jointing in true line and level 160 diameter U.P.V.C. SWR Type B pipe PRINCE/SUPREME/ASTRAL/FINOLEX or equivalent as approved by Engineer in-Charge & conforming to IS 13592-1992 with one end plain and other end socketed with rubbering, & fitting conforming to ISI 14735-1999 of approved make for Horizontal drainage line below ground level, including necessary fittings such as bends, tees, rubber packing ring etc. testing of pipeline, jointing with adhesive solvent cement including cost of excavation,lowering and laying pipes, refilling the trenches, jointing materials and all other necessary fixtures fitted, air and water tight testing of the line etc. complete as directed.

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 PRINCE/SUPREME/ASTRAL/FINOLEX or equivalentas approved by Engineer in-Charge & working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor. 110 mm Dia

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure polyurethane pipes of the following outside Dia.PRINCE/ SUPREME/ASTRAL/ FINOLEX or equivalent Low density, complete with special flange compression type fittings, wall clips etc. including making good the wall ceiling and floor. 75 mm Dia

Providing Brick bats chhara filling in sunken floors including watering, consolidating, ramming etc complete.

Construction of brick masonry chamber inside dimension as below & required depth for drainage pipeline, with required inlet and outlet for under ground C.I. inspection chamber and with 230 mm thick brick wall having crushing strength not less than 35 Kg. /sq.cm. in C.M.1:5 (1cement : 5 sand) C.I. Cover with frame(Light duty 455 mm X 610 mm internal dimension, total weight of cover with frame not less than 38 Kg. ( weight of cover 23 Kg and weight of frame 15 Kg),R.C.C. top slab with 1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size B.T. Kapchi) foundation concrete 1:2:4) (1 cement : 2 sand :4 graded stone aggregate 40 mm nominal size) inside plaster 15mm thick in cement mortar 1:3 (1cement : 3 sand ) finished smooth with floating coat of neat cement slurry on walls and bed concrete curing etc. in true line and level/slope etc. complete as directed by Engineer In charge.Inside dimension 455 mm x 610 mm and 450 deep or more for pipe line with one or two inlets as directed by Engineer in Charge.

Providing and fixing Urinal or approved quality including conecting the Urinal with waste pipe , tap etc. complete.(A) White earthenware flat back or corner type size 430mm x 260mm x 350mm., including painting of fittings and cutting and making good the walls and floors wherever required, complete as directed by engineer-incharge. (Make Parryware, Hindware, Cera, Jaquar)*.

Providing and fixing wsh down water closet (European type, W.C. Pan) with integral P or S trap including jointing the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand) (A) vitreous China Pattern :(i) in white colour and Providing and fixing plastic seat and cover for wash down water closer with C.P. brass hinges and rubber buffers. White plastic seal and cover. Providing and fixing 12.5 Litres low level flushing cistern with a pair, of C.I. or Mild brackets, complete with fittings such as lead valve less syphon, 15mm nom.nal size brass ball valve with polythene float, C.P brass handle unions and couplings for connections, with inlet, outlet and overflow pipes, 40mm dia. porcelain enamelled flush bend including cutting holes in walls and making good the same connecting the flush bend with cistern and closet Vitreous China (I) In white colour (Make Parryware, Hindware, Cera, Jaquar)*.

Providing and fixing water closet squatting Pan (Indian type W.C. Pan) size 580mm (A) Vitreous China.(I) Long pattern = White colour and fixing 100mm size P or S trap for water closet squatting pan including jointing the trap with the pan and soil pipe in cement Mortar 1:1 (1-Cement : 1-Fine sand)(A) Vitreous China. and fixing in Cement Mortar 1:3 (1-Cement : 3-coarse sand), pair of white vitreous China 250mm x 130mm x 30mm footrest to long pattern squatting pan water closet. Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete.(ii) 25mm dia, etc complete as directed by engineer-incharge.(Make Parryware, Hindware, Cera, Jaquar)*.

Providing and fixing 15mm dia. brass screw down stop tap make such as Cera,Hindware,Jaquar including fixing in pipeline etc. complete as directed by Engineer In charge. '

Providing and fixing C.P. brass Heavy duty bib cock with cap of approved quality conforming to IS standards. 15 mm nominal bore, with all fittings, etc complete as directed by engineer-incharge. (Make Jaquar, Kohler, Roca, Cera, Parryware, Hindware, Plumber)*

Providing and fixing 50mm dia. gun metal check or non return full way wheel valve in pipeline of approved quality etc. complete as directed by Engineer In charge.

Providing and fixing PVC SWR Nahni Trap IS 14735 for drain - 75 mm diameter with jali of the following nominal diameter of self cleansing design with C.I. Scread down or hinged grating including the cost of cutting and making good the walls etc. as per the approval of Engineer in charge.

Providing and fixing wash basin Cera,Hindware,Somany (550x400 mm ) counterfit Cera/ hindware , including 40 mm dia C.P. brass waste, 40 mm dia waste pipe, 15mm dia flexible pipe and rubber plugs etc. complete as directed.

Providing and fixing C.P. brass Heavy Duty Swan Neck Type Pillar cock {Make Jaquar, Kohler, Roca, and/or as approved by Engineer-incharge Pillar Cock with Raised ‘J’ Shaped Swinging Spout (Table Mounted Model)}of approved quality conforming to IS:Standards : 15 mm nominal bore (Make Jaquar, Kohler, Roca, Cera, Parryware, Hindware, Plumber)*

Providing and fixing 2 in 1 Bib tap 15 MM, of Cera/Hindware/Jaquar Or Equivalent capstan head, screw down high pressure with screws, shanks and back nuts etc. as per the approval of Engineer in charge.

Providing & fixing 600 mm X 450 mm beveled edge mirror Cera,Hindware Or Equivalent of superior glass mounted on 6 mm thick AC sheet or plywood sheet and fixed to wooden plugs with C.P.brass screws and washers, including fixing C.P. brass bracket support and guard rail fixed to wooden plugs with C.P. brass screws etc. complete as directed by engineer In charge.

Providing and fixing 600 mm X 200 mm size C.P. brass towel rail Cera,Hindware Or Equivalent complete with C.P. brass brackets fixed to wooden plugs with C.P. brass screws etc. complete as directed by Engineer In charge.

Providing and fixing PTMT soap Dish Holder Cera,Hindware Or Equivalent having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms etc. as per the approval of Engineer in charge.

Providing and fixing Stainless steel A ISI 304 ( 18/8) kitchen sink ( NIRALI BRAND ) as per IS 13983 with CI brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink with drain board 510 x 1040 mm bowl depth 225mm as directed by Engineer in Charge

providing and fixing double coated syntex or equivalent PVC (ISI) mark water tank of required capacity each with al necessary fitting & connection etc Comp. on terrace as directed by Engineer in Charge

Providing and fixing C.P. Brass Shower rose make of Cera, Hindware, Jaquar with 15mm or 20mm inlet. (A) 100mm dia as directed by Engineer in Charge.

Providing and fixing 2 in 1 Mixture Cock make of Cera, Hindware,Jaquar with 15mm or 20mm inlet. (A) 100mm dia as directed by Engineer in Charge.

Providing carbon dioxide type fire exit 4.5 KG capacity with ISI mark etc. as directed by Engineer in Charge.

Providing dry chemical powder type fire extinguishers of 5 kg/Capacity with ISI mark (IS 2171) etc as directed.

Forming groove/patta/plaster band of uniform size in the top layer of washed Sand plaster of (15 -30)Cm wide and 20 mm thick on finish Exterior surface as per approved pattern and finishing the groove complete as per specifications and direction of the Engineer-in-charge.

Providing and fixing shower seat of standard make as per following specification. • Stainless steel 304 grabe • Pipe OD-1 inch • Seat dept- 400 mm • Seat width – 500 mm • Seat height – 470 mm • Plate thickness – 2 mm • Anti-skid floor flanges of 6 mm OD and 5 mm thickness with rubber gasket • Argon welding (GTAW), perfect right angle • Matt finish • Designed to promote independent transfer by user from wheelchair also Can sustain weight upto 200 kgs. as directed by Engineer in charge.

Applying priming coat over new steel and other metel surface after and including preparing the surface by throughly cleaning, oil,grease, dirt and other foreign matter and scoured with brushes fine steel wood, scrapers and sand paper with ready mixed priming paint brushing red lead. Painting two coats on new steel and other metal surface with enamel paint, brushing, interior to give an even shade including cleaning the surface an even shade including cleanicn the surface of all dirt, dust and other foreign matter.

Providing and applying Bondvoll's NATURA synthetic texture plaster of average thickness 18 mm consisting of 12 mm thick smooth mala plaster in cement mortar 1:3 (1 cement : 3 fine sand), natura primer coat, natura stone texture and natura clear coat with necessary grooves, curing etc complete for all heights as per the pattern given by the architect and as instructed by the engineer-in-charge.

providing and Health Fauset Heavy duty with hook with fittings etc. of standard make as directed by engineer in-charge.

Providing and applying two component acrylic polymer modified cementitious elastic waterproof coating (make SG Globlastic or equivqlent) for concrete and masonery surface used for multiple application (2 or more coat) for water proof including cleaning of surface, paint, dirts etc, mixed with two components throughly to a uniform paste and apply it on the wet concrete surface with brush and slurry should be apply within 20 minutes as specified with all labour charges and materials etc. complete as directed by engineer in-charge.

Carring out plinth treatment to post construction / existing structure by spraying chemical solution for termite control treatment including labour and material consistment with I.S.I specification. Using Chlordene and Chiorpurfiles 20 EC. As Per 6131_paret-II Consentration Weight one percent is recommended i.e one litre 20 EC chemical emulsion with 19 liter give 1 % concrentration inclusive of one litre chemical emulsion appication at the rate of 5 Litre chemical / Sqm of surface is recommended as per I.S code

Providing and Applying Multi-Color craft / art painting using Acrylic and/or Enamel Paint. The width of the craft / art pattern painting shall be 250mm to 300mm (10" to 12") wide of any line thickness. The specification shall be conforming to the Ayushman Bharat Scheme of MoH&FW. It also includes, scrapping, brushing, and levelling the wall surface if required using cement putty / plaster of paris, etc.

Providing and Applying Multi-Color Illustrative painting using Acrylic and/or Enamel Paint. The size of the Illustrative painting shall be 600mm (24") dia circular and/or 600mm x 600mm ( 24" x 24") square of any line thickness. The specification shall be conforming to the Ayushman Bharat Scheme of MoH&FW. It also includes, scrapping, brushing, and levelling the wall surface if required using cement putty / plaster of paris, etc.

Providing and Applying Multi-Color Text painting using Acrylic and/or Enamel Paint. The width of the Text painting or height of the Text shall be 300mm to 450mm (12" to 18") wide of any line thickness. The specification shall be conforming to the Ayushman Bharat Scheme of MoH&FW. It also includes, scrapping, brushing, and levelling the wall surface if required using cement putty / plaster of paris, etc.

Providing and Applying Multi-Color Illustrative / Logo painting using Acrylic and/or Enamel Paint. The size of the Illustrative painting shall be 900mm (36") dia circular and/or 890mm x 660mm (35" x 26") rectangle of any line thickness. The specification shall be conforming to the Ayushman Bharat Scheme of MoH&FW . It also includes, scrapping, brushing, and levelling the wall surface if required using cement putty / plaster of paris, etc.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm

Point wiring for Light / Fan /Exhaust Fan/Bell Point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ on surface on wall/ceiling complete with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector with medium class Rigid PVC pipe and accessories cat III Make of switch and board: Havells/Anchor/Legrand/L&T (As directed by Engineer in charge)

Providing Modular Type Accessories with 16 Amp SP one way switch & 5 pin 6/16 Amp Universal socket mounted with pvc /metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection.Make of switch and board: Havells/Anchor/Legrand/L&T CAT III (As directed by Engineer in charge).

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA polyester powder coated and high U.V. & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V,Power Factor more than 0.9, THD < 10 %,CCT 4000 K to 6500K, Uniformity ratio >0.7,Luminaire efficiency> 85 lumens/watt ,LED driver efficiency > 85 % CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/Bridgelux(U.S.A.) make LED used for luminaire. (Each fitting required LM-79 & LM-80 Certificates). Tube Light with integral/ non-integral driver.20-22 Watts, Surge - 4KV,IP-20. Cat III. Make:Wipro,Havells,Philips,Bajaj.(As directed by Engineer in charge).

Providing and erecting Approved make Ceiling fan with double ball bearing ISI mark with condenser A.C. 23OV.50 c/s.1200 mm. sweep complete, canopy and 30 cms. down rod erected on existing hook or clamp with 24/0.2 , 3 core flexible wire with earthing. Make:Havells/ANCHOR/BAJAJ/USHA/ORIENT/CROMPTON.(As directed by Engineer in charge)

Providing Electronic hum Free four or more steps EME Fan regulator type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate , modules erected with necessary connections as per site situation directed by Engineer In charge.(As directed by Engineer in charge)

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA powder coated and high U.V. & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V,Power Factor more than 0.9, THD < 10 %, CCT 4000 K to 6500K, Uniformity ratio >0.7, Luminaireefficacy> 100 lumens/watt , LED driver efficiency > 85 % CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/Bridgelux(U.S.A.) make LED used for luminaire. ( fitting required LM-79 & LM-80 Certificates).(As directed by Engineer in charge)LED Lamps integral type,cool white with PC diffuser suitable for B22 LAMP holder. 5 to 8 watts.Make:Wipro,Havells,Philips,Bajaj.(As directed by Engineer in charge).

Supplying & erecting approved make low noise decorative exhaust fan having size 200mm with 1350 RPM with square frame ABS body with inbuilt lowers & square frame.Make:Havells/ANCHOR/BAJAJ/USHA/ORIENT/CROMPTON.(As directed by Engineer in charge)

Providing and erecting approved make split air-conditioning unit consisting of copper condensing unit with fan motor, hermetically sealed rotary compressor with accessories etc. duly connected separately erected evaporating unit and blower motor with its accessories by means of extra supplied proper insulated copper tubing,drain PVC pipes suitable for ( cost includes powder coated Stand, Eco Friendly green gas charging, 15A plug top & Remote Control) with necessary core cutting.For 3 Star Rating of current year Make:Voltas,Samsung,O-General, Mitsubishi electric ,Daikin.

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of with medium class Rigid PVC pipe and accessories of size size 2 wire 4 sq. mm Make:-Polycab/RR cable/Havell’s (As directed by Engineer in charge)

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity with medium class Rigid PVC pipe and accessories 2 wire 1.5 sq. mm Make:-Polycab/RR cable/Havell’s (As directed by Engineer in charge)

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity with medium class Rigid PVC pipe and accessories 2 wire 2.5 sq. mm Make:-Polycab/RR cable/Havell’s (As directed by Engineer in charge)

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of 3 wire 6 sq. mm size. Make:-Polycab/RR cable/Havell’s (As directed by Engineer in charge).

Miniature circuit breaker single pole 6A to 32A suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark (CAT III) Make:Legrand/Havells/anchor. (As directed by Engineer in charge)

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity (b)32 Amp. Cat III Make:Legrand/Havells/anchor (As directed by Engineer in charge)

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity (b)40 Amp. Cat III Make:Legrand/Havells/anchor (As directed by Engineer in charge)

Providing and erecting Sheet Steel powder coated Double Door 12 Way MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI) (As directed by Engineer in charge)

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty cover.(approved make OEM has to submit test certificate) & having back filling compound of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long time Necessary test report must be submitted. For Electrical Installation up to 440V in normal soil Length of pipe - 1 Mtr Back filling compound - 1 Nos Bag of 15 Kg.

providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 25 KA. at 415 V,having normal current rating up to 25 A to 100A. with Fixed thermal & magnetic release suitable to work on A.C. supply 50 c/s. with all internal connections & complete erected in existing 16 G.M.S. housing.

Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be erected as directed of 2 core 2.5 Sq. mm size. Make:-Polycab/RR cable/Finolex/Havell’s (As directed by Engineer in charge)

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable of Size 3 Core x 2.5 Sq. mm. Make:-Polycab/RR cable/Finolex/Havell’s (As directed by Engineer in charge)

Supplying and erecting approved make online Un-interruptible Power Supply system comprising flat cum-boost charger, static Inverter & sealed maintenance free SMF batteries. The charger having operating capacity for input 160-270V AC & inverter having output 230V,50 Hz Ac with 0.8 load power factor with battery, over/under voltage output with over load & short circuit protection equipment. The system housed in CRC sheet duly powder coated paint with following power backup.with MS painted batteries stand, 10% Overload capacity for momentary load.5 KVA with 1Hr Backup. Make: Su-kam, Luminious, Microtek, consult neowatt.Battery make: Exide.

Supplying and erecting horizontal / vertical mounting type storage water heater with copper container housed in M.S./S.S. body insulated with glass wool / puff complete with heating elements,adjustable thermostats 300 c to 850 C, indicating lamp, safety valve, fusible plug, etc.complete erected with coach bolts, nuts. washers & cementation.10 Ltr. with 3 KW. heating element. Cat III

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors etc. using proper clamp.(As directed by Engineer in charge).

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) Single phase 4 way SS Double door . (As directed by Engineer in charge)

Supplying and erecting Direct - On - Line Starter with 18 A. rating contactor and with 3.5 Amp. 18A range directly operated in totally insulated elegant enclosure for single phase operation up to 3 HP as per IS 13947 complete erected on P.W. Block with necessary connection.

Supplying of single phase submersible pump set suitable for 100 mm size or more dia bore well having motor capacity and discharge as under with necessary panel box Motor rating 2 HP (17 stage) pump having capacity of 106 LPM at 40 mtr head suitable for 32 mm dia. delivery pipe.

Hikvision 3.6 mm 2MP Dome CCTV Camera • 2MP High Performance CMOS • 120dB WDR • 3.6 mm fixed focal lens • 20 Mtr IR Distance • 2 MB , 1920 x 1080p Resolution • 24 hours colour view • Day and Night Colour • 4 in One Video Type Switchable (TVI, AHD,CVI/CVBS) • IP67

Hikvision 8 Channel 2Mp HD DVR + 1 TB Hard Disk Drive • HD-TVI/Analog/AHD self-adaptive interfaces input, • 8-ch video& • 4-ch audio input, • 1 SATA interface, • CH01-02 : SUPPORT 3MP @ 15FPS, • CH 03-08 : SUPPORT 2MP @ 15FPS, • H.265 Pro+/H.265 Pro/H.265/H.264+/H.264 • 32 Kbps to 6 Mbps • Main stream: When 1080p lite mode not enabled: For 4 MP stream access: 4 MP lite@15 fps; 1080p lite/720p/WD1/4CIF/VGA/CIF@25 fps (P)/30 fps (N) For 3 MP stream access: 3 MP/1080p/720p/VGA/WD1/4CIF/CIF@15 fps For 1080p stream access: 1080p/720p@15 fps; VGA/WD1/4CIF/CIF@25 fps (P)/30 fps (N) For 720p stream access: 720p/VGA/WD1/4CIF/CIF@25 fps (P)/30 fps (N) When 1080p Lite mode enabled: 4 MP lite/3 MP@15 fps; 1080p lite/720p lite/VGA/WD1/4CIF/CIF@25 fps (P)/30 fps (N) Sub-stream: WD1/4CIF@12 fps; CIF@25 fps (P)/30 fps (N)

Cabling with Cable, • Hikvision Coxial Cable 3 + 1 • BNC Connectors • Camera Mounting Box • Laying of Cable , Connecting • Camera Installation

4 U Metal Shelving Rack for DVR. • 2 x power socket • Secured with lock • Mounting and Installation

8 Channel Power Supply • 12V DC output • 5Amps

20” LED Monitor with VGA and HDMI Input • LED Screen Type • 19.5 Inch Full HD • 1080p resolution • VGA input. Make:- HP, AOC, Samsung, LG.

Supplying & erecting 5 stage single reverse osmosis water purification system with M.S. powder coated frame, prefilter housing with 'O' ring presediment filter GAC filter, carbon filter suitable buster DC pump capacity 80 psi, mention with 40 psi inline type post carbon filter auto low & high pressure switches with following size of storage tank & LPH capacity & erected as directed with one year comprehensive maintenance guarantee.25 Ltr / Hr with 30 Ltr. S.S. Pressure Tank

Providing and erecting water cooler having storage capacity 80Ltr. & cooling capacity 40 Ltr.per hour @ an ambient temp of 45˚ C. The outlet temp. of the water should drop by 15˚ C within a hour, The water cooler should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating coil, thermostats, relay etc. complete with necessary inlet & outlet connection. The body of water cooler will be made from Stainless Steel. ◦

Supply,Installation,Testing & Commissiong of 200 LPD Evacutad Tubes Collectors type Solar water Heater System (Non Pressurized). A. Specification of Tube :- 3 Layers 1. Material :- Borosilicate 3.3 Glass 2. Outer Diameter :- 58 mm 3. Inner Diameter :- 47 mm 4. Tube Lenght :- 2100 mm/ 1800 mm 5. Absorpative Coating :- Cu,Al,SS 6. Vaccume :- <5 * 10-3pa 7. Absorptance :- >92% (Am 1.5) 8. Glass Thickness :- 1.6mm 9. Emittance :- <8% (80° C) 10. Thermal Expansion :- 3.3 * 10-6° C 11. Stagnation Temperature :- >200° C 12. Heat Loss:- < 0.8w/M2 13. Maximum strength :- 0.8 Mpa B Capacity :- 200 LPD 1. Number of Tubes :- 20 2. Evacuated Tube Size :- 58*1800 C Tank Specification :- ETC GI/ ETC SS 1. Inner Tank Material :- Jindal / Essar Hot Deep Galvanized Iron/ SS304 Food grade 2. Thickness :- 0.2mm/ 0.7mm 3. Tank Cover :- 0.4 mm GI Precoated 4. Stand Material :- 1.5 mm/1.6mm GI Powder Coated 5. Insulation :- 50 mm PUF (36 Kg Density) 6. Inner and Outer Coating :- Ceramic Paint/ N.A 7. Connection :- 1" Cupline 3 or 4 Nos./1" Niple 3 or 4 Nos. 8. Electric Backup Provision :- 1.25 " Cupline D Other Details 1. Operating Pressure :- >=0.5 Kg per M 2 2. Electric Heater (Back up ):- 3 KW/6KW 3. Temperature Rise :- 75° Maximum (As Directed by Engineer in Charge).

Providng & installing 6" dia, minimum 5' height XL RWH Filters with required reducers/Bushings, with contamination avoidence abilities and below properties. ( The high density polythne filter of specified diameter (Minimum 6" dia & 10 KG/Cm2 Pressure handeling), Height Minimum 5' with 56 Kg / OCS on working pressure. Filled with at least 3 layers of foam made from combination of polyol and dicalsinate encovered with nylon made of polyamides from condensation polymerization process. The said foam should be placed at suitable layers of silicon dioxide granuals, Aggregate as in crushed- lose- noncohesive state. with around 20-50 mm granuals of burnt clay containing iron oxide & with activated carbon from a group of porous carbons manufactured by the treatment of char with oxidizing gases or by carbonization of carbonaaceous materials impregneted with dehydrating chemicals and required Natual herbs. (As Directed by Engineer in Charge ).

Approved design Infusion Well system with boring and precast chamber and filtration: - Drilling of bore well of 200 mm dia, depth upto 200 ft to 500 ft Max. - Providing and installation of 150 mm dia density 6 kg ISI DVC pipe, including fitting -up to 200 feet max. - Earth work - digging the well 1700 mm dia up to 3.4 mtrs deep including providing and fitting -1 No. - Providing and Installation of reinforced cement concrete precast module of 1.5 mtr dia and 3.4 mtr height including fitting -1 job. - Providing and Installation of v -wire SS 304 double filtration screen set of 6" dia. Inner screen of 0.75 mm slot size and 8" dia outer screen of 1.00 mm slot size in 1 mtr. - Providing and fittings 1 Set., with 1 ft. Coarse river sand., 1 ft. wood charcoal, 3 ft. 3/4 inch gravel., 4 ft. 12 inch river boulders., 1 ft Mud layering at each layer with Polynylo Mesh ( as per requirement at each layer ) for Bio filtration. (As Directed by Engineer in Charge ).

Providing and supplying in standard length ISI mark high density polyethylene H.D.P.E. Pipes suitable for portable water as per IS specification no. 4984/1995 including all local and central taxes, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to the department stores etc. 10.0 Kg/Cm2 50mm Dia HDPE Pipes

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [C] 40 mm.

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Madhu Nasini

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Ashwa Gandha

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Stiviya

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Adusho

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Bharmni

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Tulshi

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Nagarvalpan

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Alcho

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Alovera

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Bilipatra

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Aritha

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Saptagandha

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Ajamo

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Pipermit

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Mari

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Fudina

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for All Spice

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Tamal Patra

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Laving

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Taj

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Lemon Tea

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Dal chini

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Dumro

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Ram Tulsi

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Haridware Tulsi

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Calediumt

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Drum Stick

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Heliconiya (Mix)

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Ticoma yellow

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Madukamini

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Musanda red & white

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Rebon Grass

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Pedanus

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Tetra cotton (Mix)

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Ticoma red

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Jetrofa red

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Rose red & white

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Foxtil palm

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Conocrpush

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Ficus Black & Golden

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Pumeriya in 4 colour

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Pudica white

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Goldenduranta

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Red Baji

Providing & Spreeding Varmicompost (Per Bag 50kg)

Providing & Planting well developed, fresh & healthy with lush foliage at location as directed by EIC includding digging, planting, refilling, etc for Pots for Plants

Providing & Spreading Good Garden Soil as approved by Engineer-incharge

Providing & Fixing Name Plate as directed by EIC.

Providing and laying controlled cement concrete M.200 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in (A) Foundations, footings, Base of columns and Mass concrete.

Providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. Height of propping and centering below supporting floor to ceiling not exceeding 4 M. and removal of the same for in situ reinforced concrete and plain concrete work in. (A) Foundations Footings Bases of Columns etc. and Mass concrete.

Providing and laying controlled cement concrete M.200 and curing complete including the cost of formwork and excluding the Cost of reinforcement for reinforced concrete work in (D) Columns, Pillars posts and struts upto floor two level. etc complete as directed by Engineer-incharge.

Providing and laying controlled cement concrete M.200 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in Lintels, Beams, Girders and Cantilever upto floor two level etc complete as directed by Engineer-incharge. etc complete as directed by Engineer-incharge.

Providing precast cement concrete Jali/Precast cement concrete Poles/Decorative Balustrade of approved design of 50mm to 100mm dia 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc.(50mm to 100 mm thick) complete, excluding plastering of the jambs, sills and soffits. (As directed by Engineer in charge)

Steel work, welded in built up sections framed work including cutting, hoisting, fixing in position and applying a priming coat of read lead paint. (A)In beams and joists, channels angles Tees, flats, with connecting plates or angle cleats as in main and cross beams. Hip and jack rafters, purlins conneted to common rafters and the like (upto 10 ton)

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth, etc complete as per the direction of Engineer-in-charge

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm ) etc complete as per the direction of Engineer-in-charge

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm ) etc complete as per the direction of Engineer-in-charge

Providing and laying C.C. pavement of controlled cement concrete M250. The concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush and making groove joint and filling it with filler material as specified. Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work , using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) (Cement level 450 kg )

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in (B) Walls, from top of foundation level upto floor two level

Supply & fixing decorative Hanging light with glass having cylindrical or square shape having length not less than 10" & width not less 3.5" with holder, lead wire as per required length but not more than 1mm & base plate for fixing the fitting with ceiling.[a] suitable for led lamp of 5- 8 watt.

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of 2 wire 4 sq. mm size. Make:-Polycab/RR cable/Havell’s (As directed by Engineer in charge).

Drilling of Extra Depth for bore well of 200 m dia, depth above 200 ft upto 500 ft max with providing and installing of 150 mm dia density 6 kg ISI DVC pipe, including fitting, with gravel packing.as directed by engineer-in-charge.

Rajrath Construction

S K PARMAR

P.R. Patel and Co.

shree khodiyar custruction