Improvement of LWSS Kinoo Aloh Suhin, Sidh Chalet and Badoli Tiuri Phase 1st in tehsil Amb Distt Una HP

Amount

Excavation in foundation, trenches in earth work in all kinds of soil,such as pick work,jumper work.blasting work in hard rock and soft rock and in saturated soil etc. i/c all leads and lifts , stacking the excavated soil not more than 3 mtrs. clear form the edge of excavation and then returning the stacked soil in 15 cm layers when required into plinth, sides of foundation etc. consolidating each deposited layers by ramming and watering and then disposing of all surplus excavated earth as per the direction of the Engineer-in-Charge.

Providing and laying cement concrete 1: 6: 12 ( 1 cement : 6 graded stone aggregate 40 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts and as per the direction of the .Engineer-in-Chaarge.

Providing and laying cement conrete ement concrete 1:3:6 ( 1 cement :3 sand : 6 graded stone agg. 40 mm nominal size) complete and curing complete excluding cost of form work in foundation and plinth including carraige of material within all leads and lifts as per the direction of the Engineer-in-Charge.

Providing and laying cement concrete 1:2:4 (1 cement:2 sand:4 graded stone aggregate 20mm nominal size) and curing complete 50 mm thick with cement within all leads and lifts as per the direction of the Engineer-in-Charge.

Ist class brick work using common burnt clay building bricks in foundation and plinth in cement mortor 1:6 ( 1 cement: 6 sand ) in all leads and lifts as per the direction of the Engineer-in-Charge.

Ist class brick work using common burnt clay building bricks in superstructure in cement mortor 1:6 (1 cement :6 sand) in all lead and lifts as per the direction of the Engineer-in-Charge.

Ist class half brick work using common burnt clay building bricks in super structure above plinth level upto floor to level in cement mortor 1:4 ( 1 cement:4 sand ) in all leads and lifts as per the direction of the Engineer-in-Charge.

Providing and laying damp proof course to horizontal surface with cement mortar 1:2 (1 cement:2 sand) and curing complete in all respect and as per the direction of the Engineer - in- Charge.

Applying a coat of hot bitumen (mexphalt 80/100 or equivalent) using 1.70 kg. per square metre on damp proof course after cleaning the surface with a piece of cloth lightly soaked with kerosene oil complete in all respect and as per the direction of the Engineer - in- Charge.

Providing and fixing pressed steel door frame manufactured from commercial MS sheets of 1.25 mm thickness including hinges jump lock jamb, bead if required angle thrshold of MS angle 50x25 mm or base ite of 1,25 mm presses MS welded or rigidly fixed together by mechanical means, adjustable lugs with split and tails to each jamb including steel butt hinges 2.5 mm thick with guards, lck strike plate and shock as specified and laying a coat of steel Profile "A"

Providing and fixing pannelled glazed and panalled and glazed shuttrs for doors ,windows and clerestory windows including bright finshied /black enemelled iron butt hinges with necessary screws fIst class deodar wood 40 mm thick. 2 nd class deodar wood complete in all respect and as per the direction of the Engineer - in- Charge.

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centering, shuttering, struting and propping etc. with wooden battens and ballies, height of propping and centering below supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for in situ-reinforced concrete and plain Concrete work in :-

Foundation, footing and bases of columns etc. and mass concrete within all leads and lifts complete in all respect.

Flat surfaces such as soffits of suspended floors, roofs, landing and the like Floors etc. upto 200 mm thickness in all leads and lifts and as per the direction of the Engineer-in-Charge.

Beams,cantilever,girders and lintels.Sides and soffits of beams,beam haunchings, cantilevrs, bressumers and lintles not exceeding 1.00 mtr.in depth in all heights from floor.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like

Providing and laying cement concrete 1:2:4 ( 1cement : 2 sand : 4 graded stone aggregate 20 mm nominal size ) and curing complete excluding the cost of form work and reingorcement for reinforced concrete work in :-

Suspended floors, roofs, landing and shelves and their support balconies, beams, girders, bressumers and cantilevers upto floor to level complete in all respect i/c carriage of materials with in all leads and lifts.

Providing and laying cement concrete 1:1.5:3 ( 1cement : 1.5 sand : 3 graded stone aggregate 20 mm nominal size ) and curing complete excluding the cost of form work and reingorcement for reinforced concrete work in :-

Foundation, footing and bases of columns etc. and mass concrete within all leads and lifts complete in all respect i/c carriage of materials with in all leads and lifts.

Suspended floors, roofs, landing and shelves and their support balconies, beams, girders, bressumers and cantilevers upto floor to level complete in all respect i/c carriage of materials with in all leads and lifts.

(iii) Vertical surfaces such as walls (any thickness) partitions and the like i/c attached pillares buttresses, plinth & string courses and the like.

Providing mild/tor steel reinforcement of RCC work i/c bending ,binding and placing in position in complete up to floor two level in all leads and lifts and as per the direction of the Engineer-in-Charge.

Pointing on brick work with cement mortor 1:3 ( 1 cement: : 3 sand ) in all leads and lifts as as per the direction of the Engineer - in- Charge.Cut or weather struck.

Providing and laying brick tiles over mumty /terrace roofs grouted with cement mortar 1:3 ( 1 cement : 3 sand) over a 12mm(twelve millimeter) layer of cement mortar 1:3( 1 cement : 3 sand ) and finished neat including carriage of material with in all leads and lifts and other incidentals.

6 mm thick cement plaster to ceiling with cement mortar 1:3( 1 cement : 3 sand ) including carriage of material with in all leads and lifts and other incidentals.

15 mm cement plaster in single coat on rough side of brick masonry for interior plastering upto floor two level including arrises, internal rounded angle, chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth with cement mortor 1:6 ( 1 cement :6 sand ) in all leads and lifts as per the direction of the Enginner-in-Charge.

20 mm cement plaster in single coat on rough side of brick /stone/ concrete walls for interior plastering upto floor two level including arrises, internal rounded angles, chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth with cement mortor 1:6 ( 1 cement :6 sand ) in all leads and lifts as per the direction of the Enginner-in-Charge.

Providing and fixing MS grills of required pattern in wooden frame / pressed steel frame with MS flates square / rounds bars 12 mm dia with round headed bolts and nuts of by screws in all leads and lifts and as per the direction of the Engineer - in- Charge Plain grills.

Providing and fixing wire gauge shutters using galvanized MS wire gauge of I.S.gauge designation 85G(eighty five ) with wire of dia 0.56 mm(zero point five six millimetre) for doors windows and clerestory windows including bright finished black enameled iron butt hinges with necessary screws 40mm(forty millimetre )thickof second class deodar wood with in all leads and lifts and as per the direction of the Engineer - in- Charge.

Providing plinth protection 50 mm thick in cement concrete 1:3:6 ( 1 cement :3 sand : 6 graded stone aggregate 20 mm nominal size ) in all lead and lifts as per the direction of the Engineer - in- Charge.

Constructing brick masonary 'U' shape open surface drain with side wall. 15 x 22 cm in cement mortar 1:6 ( 1 cement : 6 sand) and inside plastering with cement plaster 1:3 ( 1 cement : 3 sand) including earth work and laying 10 cm cement concretein 1:5:10 ( 1 cement : 5 sand :10 graded stone aggregate of 40 mm nominal size) and 7.5 cm.cement concrete 1: 2:4 ( 1cement : 2 sand : 4 graded stone aggregate 20 mm nominal size ) and finished with a floating coat of neat cement complete as per standard design.

Providing 40x3mm flat iron hold fast 40 cms long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15 cms 1:3:6 ( 1 cement :3 sand : 6 graded stone aggregate 20 mm nominal size ) complete in all respect as per the direction of the Engineer -in- Charge.

P/F MS fan clamps type 1 of 16 mm dia bar bent to shape with hooked ends in RCC slab during laying including painting the exposed portion of roof as per standard design complete in respect .

White washing with lime on undecorated wall surface ( three coats) to give an even shade including throughly brooming the surface to remove all dirt ,dust mortor drops and loose scale of lime wash and other foreign matter complete in in all respect as per the direction of the Engineer-in-Charge.

Distempering with oil bound distemper of approved brand and manufacture ( Two coats) and of required shade on undecorated wall surfaces to give an even shade over & including a primer coat after thoroughly brushing the surface free from mortar droppings and other foreign matter including preparing the surface even & sand papering / smooth including carriage of material in all leads and lifts.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surface (two coats) to give an even shade after thoroughly brushing the surface to remove all dirt & remains of loose powdered materials complete in all respect

Providing and fixing sliding door bolts anodized transparent or dyed to required shade and colour with screws etc. complete in all respect 250x16 mm

Providing and fixing tower bolts barrel type anodized transport or dyed to required shade and colour with screws com lete in all respect. 250x10mm.

Providing and fixing aluminium handle anodized transparent or dyed to required shade and colour with screws etc. complete in all respect 100mm dia

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint to give an even shade including cleaning the surface of dirt ,dust and other foreign matter with enamel with enamel paint other than white complete in all respect as per the direction of the Engineer-in-Charge.

Cement concrete flooring 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size ) laid in one layer finished with floting coat of neat cement in all leads and lifts and as per the direction of the Engineer-in-Charge 40 mm thick.

Providing in RCC work smooth finishing of the exposed surface with cement mortor 1:3 (1 cement : 3 Sand) complete in all respect within all leads & lifts.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by throughly cleaning oil, greas,dirt,and other foreign metter with ready mixed paint brushing wood primer pink complete in all respect as per the direction of the Engineer-in-Charge.

Painting two coats excluding priming coat on new wood and wood surfaces with enamel paint to give an even shade including cleaning the surface of dirt ,dust and other foreign matter sand papering and stoping complete in all respect as per the direction of the Engineer - in - Charge.

P/F of angle iron door, window, clerestory windows manufactured from MS angle iron section of 50x50x6mm thickness including hinges jamb, lock, jamb, bead and if required angle threshold of mild steel angle 50x25 mm welded or rigidly welded by mechanical means, lungs withsplit end tail to each jamb i/c. steel butt hinges 2.5 mm thick with provision for locking arrangement and shock observer as specified & applying a coat of approved steel primer after pretreatment of furface as directed by the Engineer-in-Charge.

P/F of 1 mm thick MS Sheet garage door with frame of 40x40x6mm angle iron 3.15 mm gusset plates at the junctions and corners, all necessary fitting complete including applying a priming coat of red lead paint using flats 30x5mm for diagonal braces and central cross pieces.

Steel work welded built up sections, trusses and framed work , including cutting , hoisting , fixing in position and applying a priming coat of red lead paint in beams joists channels, angles , tees, flats with connection plates or gratings framed guard bars, ladders,. railling, brackets and similar works complete in all respect as per the direction of the Engineer - in - Charge.

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign metter and scoured with wire brushes fine steel wool scrapers and sand paper complete with ready mixed priming paint brushing red lead, red-oxide/ zinc oxcide chrome.in all respect as per the direction of the Engineer-in-Charge.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint to give an even shade including cleaning the surface of dirt ,dust and other foreign matter with enamel with enamel paint other than white complete in all respect as per the direction of the Engineer-in-Charge.

Providing / fixing vitreous china water closet squatting pan (Indian type WC pan) size 580 mm ( Earth work, bed concrete, foot rest and trap to be measured and paid for seperately Orissa pattern complete in all respect as per the direction of the Engineer-in-Charge.

Providing / fixing of PVC "P" Trap complete in all respect as per the direction of the Engineer-in-Charge.

Providing / fixing of PVC bend 50 mm dia complete in all respect as per the direction of the Engineer-in-Charge.

Providing / fixing of PVC waste pipe and ventilating pipes complete in all respect as per the direction of the Engineer-in-Charge.

100 mm dia

50 mm dia

Providing / fixing of wall ceiling and floor galvanized MS tube (Light) tube fitting and clamps including making good the wall ceiling and floor 15 mm thick complete in all respect as per the direction of the Engineer-in-Charge.

Providing / fixing of CP brass bib cock with capstan head 15 mm dia complete in all respect as per the direction of the Engineer-in-Charge.

Providing / fixing of CC Hume pipes each 750 mm dia 1200 mm long required for excavation at site complete in all respect as per the direction of the Engineer-in-Charge.

Providing / fixing of 10.00/12.50/15.00 litres vitreous china low level flushing cistern with a pair of C.I. or mild steel brackets, complete with fitting such as lead valves less syphon, 15 mm nominal size brass ball valves with polygthene float. C.P. Brass handles unions and coupling for connections with inlet, outlet and over flow pipes , 40 mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet ( Overflow) pipe to be measured and paid for seperately.

Fixing inlet, outlet, over flow and Scour pipe of GMS pipe of following internal dia (medium grade) including extra carriage within all leads and lifts and as per the direction of the Engineer-in-Charge.

Providing & fixing of following diaCI sluice valve (with hand wheel) make leader/ Kirlisker as per IS 780:1984 Class - I upto 300mm dia. i/c brass spindle & as per 2906 - 1984 Class II for diameter more than 300mm complete with bolts, nuts, rubber insertion etc. (The tail pieces if required shall be measured & paid seprately) complete in all respect with in all leads & lifts.

80 mm dia PN-1

100 mm dia PN-1

Constructing chamber 600x600x750 mm size for sluice valve with CI surface box 100 mm top dia., 160mm bottom dia., & 180mm deep with chained lid & RCC top slab in 150mm thick RCC walls in c.conc. 1:2:4 (1 cement : 3 snad : 6 graded stone aggregate 20mm nominal size) 100mm thick foundation conc. 1:5:10 mix (1 cement : 5 sand : 10 graded stone agregate 40mmnominal size) & inside plastering with cement mortar 1:3 (1 cement : 3 sand) finished with a floating coat of neat cement i/c curing complete. complete in all respect within all leads & lifts.

Providing & fixing MS man hole cover having fram size 500x500 MM made from angle iron 65x65x5 mm base plate and man hole frame 45x45x5mm with 3.15 mm thick MS sheet cover having locking arrangment, lock & lifting handles. The frame should be duly embeded monollithically in concret during casting complete (Not less than 25 Kg) in all respect within all leads & lifts.

Providing and laying cement concrete 1:5:10 (1 cement : 5 sand : 10 graded stone aggregate 40 mm nominal size ) with 15% plum & curing complete excluding the cost of form work in retaining walls breast walls, the size of plums shall usually be 150 mm to 300 mm complete in all respect i/c all leads and lifts and as per the direction of the Engineer-in-Chaarge.

Excavation in foundation and trenches etc. in all kinds of soils such as pick work, jumper work, blasting in soft / hard rock, chiselling / wedging out of rock where blasting prohibited) saturated soil stacking the excavated soil as directed by the Engineer-in-charge clear from the edge of excavation and then returning the stacked soil in 15cm layers when reuired into plinth sides of foundation etc. consolidating each deposted layer by ramming and watering and then disposing of all surlus excavated earth as directed by the Engineer-in-charge in all leads and lifts.

Providing and laying cement conrete ement concrete 1:3:6 ( 1 cement :3 sand : 6 graded stone agg. 20 mm nominal size) complete and curing complete excluding cost of form work in foundation and plinth including carraige of material within all leads and lifts as per the direction of the Engineer-in-Charge.

Providing and laying cement concreteusing M-25 as per IS: 3370 Part-1,2009 and curing complete excluding the cost of form work & reinforcement for reinforced concrete work in :-

Foundation, footing, bases of columns & the like & the mass concrete

Column, pillars, posts & struts upto floor two level

floor two level to floor three level

floor three level to floor four level

floor four level to floor five level

Lintels, beams garders bressumers & cantilevers upto floor two level

floor two level to three level level

floor three level to all level level

Wall (any thickness, but not less than 0.10 m thickness) attached pilasters, buttresses, plinth & string course etc. from top of foundation level upto floor two level

floor three level to floor all level level

Arches upto floor two level

floor three level to floor four level

floor four level to floor five level

Suspended floors, roofs, landings etc.

Bottom ring beam & Top ring beam (floor two level to all level)

Providing formwork with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centring, shuttering and propping etc. with wooden battans and ballies height of propping and centring below supporting floor to ceiling not exceeding 4 meters and removal of the same for insitu reinforced concrete and plain

(i) Foundation, footing, bases of columns etc. and mass concrete

(ii) Flat surface such as soffits of suspended floors, roofs, landingand the like

(iii) Vertical surfaces such as walls (any thickness) partitions and the like i/c attached pillares buttresses, plinth & string courses and the like.

(a) Upto 4.00 mtrs.

(i) For vertical surfaces of tank

(iv) Columns, pillars, post & struts

(b) Beyond 4.00 mtrs.

(v) Beams, cantilever, girders & lintels, sides & soffits of beams, beam haunchings, cantilevers, bressummers & lintels not exceeding 1.00 mtrs. Depth in all height from floor

(vi) Providing form work of ordinary timber plankings, so as to give rough finish including centring, shuttering, strutting and propping etc. with wooden battans and ballies height of propping and centring below supporting floor to ceiling not exceeding 4m and removal of the same for insitu reinforced concrete and plain

(In Arches not exceeding 6.00 mtr.span) Beyond 4.0m height

Providing Tor steel reinforcement for RCC work including bending, binding & placing in position complete in all leads & lift upto floor all level

Providing in RCC work smooth finishing of the exposed surface with cement mortor 1:3 (1 cement : 3 Sand) complete in all respect within all leads & lifts.

Finishing wall with water proofing cement paint of approved brand & manufacture & of required shade on undecorated wall surfaces (two coats) to give an even shade after thoroughly brushing the surface to remove all dirt & remains of loose powdered material.

Providing & fixing 500 mm dia. CI man hole cover with frame and the weight of frame & cover should not be less than 100kg complete in all respect within all leads & lifts.

Fixing of GMS pipes conforming to relevant BIS codes of below mentioned diameters fully jointed with table - 5

b) Scour Pipe /in let/Outlet & Over flow pipe 80 mm dia.

Steel work welded in built up sections, trusses & framed work i/c cutting, hoisting fixing in position & applying a primary coat of red paint in grating, framed guard bars, ladders, railing, brackets & similar works

Fixing GMS pipes conforming to IS 1239-1990 / 2004 (Part-1) screwed & socketed joints (Light grade ) excluing the cost of excavation in trenches

Providing & fixing CI sluice valve (with hand wheel) as per IS 780:1984 Class - I upto 300mm dia. i/c brass spindle & as per 2906 - 1984 Class II for diameter more than 300mm complete with bolts, nuts, rubber insertion etc. (The tail pieces if required shall be measured & paid seprately) complete in all respect with in all leads & lifts.

P/Fixing Vent pipe i/c CI cowl complete for OHSR complete

Wiring for light/Fan point/Exhaust fan point/call bell point with 1.5 Sq.mm PVC insulated copper conductor cable in surface/recessed PVC conduct at required including carriage of all material within all leads and lifts. Group "C"

Wiring for light/power plug with 2 x 4 Sq.mm PVC insulated copper conductor or single core cable in surface/recessed steel conduit alongwith 1 No. 2.24 mm dia bare copper wire for loop earthing as required including carriage of materials within all leads and lifts.

Wiring for circuit wiring with 2 x 2.5 Sq.mm PVC insulated copper conductor single core cable in surface/recessed steel conduit as required including carriage of material within all leads and lifts.

Wiring for sub-main wiring with the following size of copper conductor single core cable in surface/recessed steel conduit as required including carriage of materials upto all leads and lifts. 2x6 Sq.mm

Supplying and fixing metal box of 180 x 100 x 60mm deep (Nominal size) on surface/recess with suitable size phonolic leminated sheet cover fixing 3 pim 15/16 amps socket tumber/piano type switch connections painting etc. including carriage of materials within all leads and lifts.

Supplying and fixing backellite batten/angle holder including connection as required.

Providing, installing, testing and commissioning of ceiling fan and regulator including wiring the rod of standard length (upto 30cm) with 1.5 Sqmm PVC insulated copper conductor single core cabe etc. as required sweep type. Category. A

Providing, installation, testing and commissioning of prewired flourscent tube fitting complete with ballast, starter and capactors but excluding flourscent tube rod, suitable to operate on 230 volts single phase A.C.supply directly on surface with copper wiring as required including carriage of materials within all leads and lifts tube fixture 1 x 36 watt Box type Category "A".

Supplying and fixing 40Amps to 63 Amps rating 240 Volts "L" series miniature circuit breaker of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required including carriage of material within all leads and lifts. Category- A, 63 Amps.

Supplying and fixing of following way single pole and neutral sheet steel MCB distribution board 240 volts on surface/recessed completed with tinned, copper busher neutral link, earth bar, detachable gland plate inter -connections, including painting, earthing etc. as required Bus bar 8 way.

Supplying and fixing 5 Amps to 32 Amps rating 240 volts, G series miniature circuit breaker of following poles in the existing MCB, DB complete with connections testing and commissioning etc. Category "A", single pole.

Earthing with G.I. pipe earth, pipe 4.5 mtrs length, 40mm dia including accessories and providing masonry enclousres with cover plate having locking arrangement and watering pipe etc.( but without charcal coke and salt) complete as required including carriage of materials within all leads and lifts.

Extra using salt and charcoal for pipe earth electrode as required, including carriage of materials within all leads and lifts.

Supplying and laying 6 Sqmm G.I.wire at 0.50 mtr below ground level for conductor earth electrode, including soldering etc. as required including carriage of materials within all leads and lifts.

Providing, fixing & testing Street Light Fixture with CFL of 36 watt, copper ballast, G.I. Pipe bracket, complete in all respects.

Rising main

Laying , jointing, testing and commissioning at site in trenches of GMS plain ended pipe conforming to IS 1239-1978 (latest with upto date amendments) capable of withstanding required text pressure as prescribed in BIS cde in a random length 5.50 to 6.50 mtrs. The pipe ends shall be beveled and suitable for but welding and including the cost of joints with but welding confirming to IS 816-1969 or latest as applicable (Leak proof) in three layers at site of work with welding rods of stand red make and all allied accessories whatever required for welding at site, tail pieces tees bends manufacture from parental pipes etc and cutting where ever required as per site including carriage i all lead and lifts. ( Earth work, Butt welding, MS Flanges shall be measured and paid for separately)

GMS pipe 80 mm dia (Medium class) from RD. 0 to 1500 with MS flanges Table -28 for WSS Sidh Chalet.

GMS pipe 80 mm dia (Medium class) from RD. 0 to 390 with MS flanges Table - 17 for WSS Kinno Aloh Suhin .

GMS pipe 80 mm dia (Medium class) from RD. 1500 to 2590 with MS flanges Table -17 for WSS Sidh Chalet.

GMS pipe 80 mm dia (Medium class) from RD. 0 to 10 with MS flanges Table -17 from T/Well to collection Tank of WSS Sidh Chalet.

GMS pipe 80 mm dia (Medium class) from RD. 390 to 870 with MS flanges Table - 5 for WSS Kinno Aloh Suhin .

Providing & welding of MS flanges confirming to table as specified below as per IS- 6392-1971 (latest with upto ammendment ) welding of MS flanges with GMSERW pipe on both end ( The cost of GMSERW pipe to be measured & paid for seperately)according to relevent BIS standard The welding of flanges with pipes as per IS: 816-1965 with electrode as per IS: 814-1967 including required Nos. and size of M.S nuts and bolts as per IS: 1369-1967 and compressed asbestos fibre jointing geskets sheet not less than 3 mm thick as per IS; 2712-1965. The welding of flanges to be done on both faces in three layers(two inner & one outer) to make the joints leak proof and to the entire satisfaction of the Engineer - in -charge. including carriage of material in all leads and lifts.

MS flanges Table - 28

MS flanges Table - 17

MS flanges Table - 5

Providing circumferencial butt welded joints by electrical arc welding to following dia & class pipes,welding of pipes to be done in three layers to make the joints leak proof and to achieve the minimum effective throat thickness of weld conforming to IS- 816-1969 specifications, by using welding electrodes of 2.5 mm to 6.3 mm of Advani oerlikon (Adore)-CITOJET/ESAB make, conforming to IS 814-1991, at site of work complete in all respects and including DPT test for joints & manual/mechnical handing of pipes in all leads and lifts to the entire satisfaction of Engineer- in- charge..

80 mm dia GMS Pipe (Medium)

Laying, jointing and testing in trenches GMS pipes ( light grade) confirming to ISI specification including commissioning and cost of all fittings such as Tees, Union, albow, Reducer etc. in respect of following diameters in distribution system (Earth work in trenches to be measured and paid for separately) including entire carriage of material in all leads and lifts as per the directoon of the Engineer-in-charge.

15mm dia.

20mm dia.

32mm dia.

40 mm dia.

50 mm dia.

65 mm dia.

Providing and fixing of brasss full way valves with ( hand wheel ) complete in all respect and as per the direction of the Engineer-in-Charge in all leads and lifts of the following diameters.

15 mm dia.

20mm dia.

25 mm dia.

32 mm dia.

50 mm dia.

65 mm dia.

Dismentalling of of old pipe GMS pipes in existing distribution system where changing is required of following including stacking of material at site in all leads and lifts and as per the direction of the Engineer-in-Charge.

15mm dia.

20 mm dia.

40 mm dia.

50 mm dia.

Re-Laying, jointing and testing in trenches GMS pipes ( light grade) confirming to ISI specification including commissioning and cost of all fittings in respect of following diameters in distribution system (Earth work in trenches to be measured and paid for separately) including entire carriage of material in all leads and lifts as per the directoon of the Engineer-in-charge.

20 mm dia.

40 mm dia.

50 mm dia.

Submersible Pump for LWSS Kinoo Aloh Suhin

Supply of submersible pumping set of reputed make such as KSB/ Calama / BS/ Worthigton / Groundfos/ LUBI / Hindustan/ Sabar/ Seerex/Johnston / Amrut, confirming to latest relevent BIS . The pump should be fitted with free fine impellers of suitable alloys as per BIS ; 5659-1978 with upto date amendments, suitable for raw / clear water having greased packed bearing and shell with wound stator on motor side and with shaft protection on pump side ensuring better life for shaft conforming to BIS specifications. The pump shall be directly coupled to submersible motor of same as that of offered submersible pump make confirming to BIS ;9283-1979 with upto date amendments, totally dust and water proof for submersible pump, duly isolated from the pump by intermediate casing with double mechanical seal in oil chamber and grease packed, lubricated bearing and provided with stainless steel thrust bearing plate to withstand non vertical loads with minimum wear tear.It should also be fitted with a device to make up expantion of water with heating of motor. The pumpset should include water level guard i/c cable ,errection clamps, cable clips and depth gauge etc. and suitable for opertion on data given below. . Specifications offered a Pumps :- Specifications i) Make ii) Model iii) No. of stages iv) Manufacter's certificate to be attached Performance i) Discharge ii) Head iii) Efficiency of Pump a) Duty Head b) (+) 10% Duty Head. c) (-) 15% Duty Head d) Performance curve to be attached b) Motors; Specification i) Make ii) Model iii) B.H.P iv) Speed v) Insulation

Discharge, (Q) 4.15 LPS

Total Head ( H ) 77.77 Mts.

SWL in Tubewell 40.00 mtr. bgl.

R.L. point of discharge 101.60 mtr

Seasonal fluctuation + draught condition + bowl assembly.9 mtrs.

Drawdown in Tubewell 12.00 mtrs.

R.L. of lowest point of pump set installation 31.60 mtr

Static coulmn lift= 67.00 mtrs.

Rsiing Main Column pipe

Length = 180.00 mtrs Length 75.00 mtr

Dai 80 mtrs Dia 80 mm

Class GMS (M) Class GMS (M)

iv) Pumping hours 8 hours

v) Alititude of installations above M.S.L 478.00_mtr

vi) Characteristic of water

a) Temperature 25 Deg Cel.

b)Turbidity __________________JTU

c) Allkanity _________________mg/1Ca Co3

d) Size of solids _______________ mm

e) others

vii) Depth of T/well 89.00 mtr

viii) Dia of T/well assembly 175 mm

ix) Length of assembly pipe mtr

x) Dia of housing pipe 175 mm

xi) Length of housing pipe mtr

OPERATING CONDITIONS

i) Type of current A.C Three phases.

ii) Frequency 50 Cycles/ Sec.

iii) Rated Voltage 415+/-15% Volts

iv) System of earthing Double Loop earthing as per BIS 3843-1987 latest

v) Speed of Revolution __________________ RPM 2900

MOTOR

i) Ref to BIS code BIS 9283-1979 with upto date amendments

ii) Type of enclousre of motr As per BIS :4691-1985 (latest)

iii) Mechnical out put in HP

iv) Class of insulation : Class B The motor should be able to withstand intial current of 2.50 times the rated current for two minutes without suffering damages of permanet deformations

i) Ref to BIS code BIS 5659-1978 with upto date amendments

ii) Driver Type Electric drivern

iii) Operating Range -15%to +10% of Total head at duty point

iv) Deliver size of Pump ;---------- (to be quoted by tenderer)

Providing ICTP Main Switch with HRC fuses of Havell/L&Tmake and having capacity extra of the operational rating as per IS : 4864-1978I with upto date amendments. ICTP Switch: i) Make: ii) Type: iii) Capacity: 32 Amp.

Providing MS Sheet steel fabricated floor mounted switch board including angle iron post of suitable height and size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising and capable of mounting the following accessories with all internal connections. ICTP Switch: i) Make ii) Type (iii) Capacity : 63 Amp Panel /Switch Board. i) Drawing. ii) layout Plan.

MCB of L&T/Havells make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. MCB (1) Make (ii) Type iii) Range iv) Capacity. 32Amp

ELCB of recommended make L&T/Havells as per IS ;2516-1985 with up to date ammendments, and of suitable range which should have control box , operating handle and trip / reset bush button on / off of indicators,reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. ELCB I) MAKE II) Type iii ) Range iv) Capacity. 25 Amp

The voltage monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage,reverse phasing,overloading and phase voltage difference as per IS; 3842 ( Latest Edition ) Voltage Monitor Relay I) MAKE II) Type iii ) Range 0-500 amp

Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current one copper bar of half the rating of full length for neutral phase as per IS : 8084-1976 and IS: 11353-1985 read with BIS : 5578- 1985 with upto date ammendments Three phase indicator lamps complete with toggle switches for Bus Bar Chamber individual motors as per IS: 3452 (P-I&II) with upto date ammendments. i)Type ii)Make iii)Rating

Three phase indicator lamps complete with toggle switches for individual motors as per IS 3452 ( P- I&II) with upto date amendments. Three phase indicator

Capacitor of BHEL / GEC / L&T /Mecheil make as per IS ; 2834-1968 with upto date amendments, to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter / IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB. (i) Type (ii) Make (iii) Range 3 KVAR

Providing suitable DOL starter of L&T/BHEL make as per IS : 8544-1979 with'upto date amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic 'type overload release and dashpot, time lag, under voltage release with or without 'initial oil filling as the case may be with single phase prventor as per IS ;1248 ( P-5)1983 with up to date amendments.Single Phase Preventor i) Type ii) Make

Providing and fixing of double flange Cast Iron Sliuce valve of Leader / Kirloskarr make for the Column pipe of pump and capable of withstanding the normal seat pressure and as per IS 780-1984(Cast Iron) with latest ammendments PN 1.0 in Column pipe 80 mm dia.

Providing and fixing of double flanged swing type cast iron Reflux valve of Kirloskar/ Leader make having Bye pass arrangement on the Rising Main of the of the Pump and capable of 'withstanding normal Seat Pressure as per IS:5312-1984 (P-I) (Cast Iron) with latest ammendmets PN 1.00 in R/main 80 mm dia.

Providing pressure gauge of Prega/Precision make complete with all accessories such as stop cock, Copper tubing as per IS: 3624-1987 with upto date ammendments. Pressure Gauge i)Make ii)Range.

Supply of PVC 3 core jointless, flat water proof copper cable with copper conducter as per BIS 694-1998 latest with upto date amendments, suitable for the pumpsets offered from MCB to motor including all other electrical equipments/ accessories such as thimble, flexible pipe,solder, nuts and bolts, cable glands, clips etc, laid in pipes or trenches under floor . The type, size and make shall be subject to approval of HPSEB authorities. Submersible Cable i)Make. Finolex / Havells ii) Size. 4 mm Sq.

Lowering of GMS(M) Column pipe assembly 80 mm dia(MG) including MS flanges of Table 17 as per IS : 6392-1971 with upto date amendments, rubber/asbestos gasket of min. 3mm thickness as per IS 2712-1979 and required numbers of nuts and bolts as per IS ;1364-1983 . The Column pipe shall be as per relevent IS Code The Column pipe should be extended upto 5 mtr. beyond the outer wall of the pump house in the direction of Rising main . The Column pipe should be properly jointed with the Rising main including all necessary accessories like increaser / reducer, flanges, bends etc, including supporting clamps (2Nos.) at the top of T/well assembly, and as per the direction of Engineer - in - Charge. Column Pipe i) Size 100 mm dia. ii) Class GMS. iii) length. mtrs. Pipes shall be issued free of cost by the deptt at divisional store at Barnoh).

Installation of all items appearing above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and laying copper PVC insulated 3 core armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS :1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster/IEC/ICC/EICO/National / Grandlay make including all othe accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor. Armoured Power Cable From Supply Side From meter of HPSEB to Bus Bar and Switch) i) Size 4mm Sq. ii) Make finolex /Havells iii) Type armound power cable iv) Capacity v) Core.

Providing and fixing double earthing with G.I. wire 8 SWG thick electrode complete with material such as thimble, nuts and bolts, charcoal, salt, copper strip as per IS 3043-1987 with upto date amendments for motors and other eletrical equipments and digging of pits etc. complete in all restect as per the dirction of the Engineer-in-Charge. i) G.I. wire 8 SWG

Centrifugal Pumping Machinery for WSS Kinoo Aloh Suhin

Providing horizontal spindle ,horizontal / radial split casing / end suction (back pull out arrangement). Single / double / multi stage centrifugal pump or combination of pumps in series / parallel of recommended make such as Mather and Platt /KSB/Beacon weir/Kirloskar / BE/ Jyoti/LUBI/GROUNDFOS/HINDUSTAN as per BIS IS 1520 1980 with upto date ammendments read with IS- 9137. 1978 or latest edition suitable for lifting water for under mentioned characteristic with Bronze impellers / priming funnels, casing ring and shaft sleeves of Bronze shaft of stainless steel with cast iron casing, coupled directly through a flexible coupling on a common cast iron/cast steel base plate (base plate to be framed from the manufacturers of the pumping unit only) to slipring/Squirrel cage screen protected drip proof induction motor/,motors of standard make such as Kirloskar /Bhel /Crompton/NGEF /GEC/ Seimens /jyoti/ LUBI/GROUNDFOS/ HINDUSTAN and suitable for operation on 415 (+/-5%) volts. 50 Cycles/Sec., 3 phase AC electric supply. The power of electric motor/motors should be at least + 10% in excess of the maximum power required by the pump/pumps in the Operation range of (+10%) and (-15%) of the duty point head. The motor/motors as per IS 325 IS 1978 with upto date amendments read with IS 900 1972 it should include cost of Bearing. Nuts, Bolts and painting etc. and should meet the following requirements.

Coupling

Base Plate

Discharge (Q) 4.15 LPS.

Total Head (H) 88.75 mtrs.

LWL In collection tank 98.60 mtr

b)R.L. of shaft 98.60 mtrs.

c)R.L. of discharge Pt. 172.80 mtrs.

d)Suction lift.

e)Discharge Head = 3.00 mtrs

f) Static Head 74.20 mtrs.

Rising main.

Length 690 mtrs.

Diameter 80 MM

Class GMS (M)

Pumping hours. 8 hours.

Altitude of installations above M.S.L 478.00 mtrs.

Characteristic of Water

a)Temperature 20 Deg.Col.

b)Turbidity ________ JTU

c)Alloanity _________ mg/1 ca Co3

d)Size of solids __________ mm

e) Others.

Providing ICTP Main Switch with HRC fuses of Kilburn/L&T / Havells/Siemens/Standard make and having capacity 30% extra of the operational rating as per IS-4064 : 1978 with upto date amendments, immediately after the Energy meter of the HPSEB. ICTP Switch: i)Make ii)Type iii)Capacity: 63 Amp

Providing ICTP Main Switch with HRC fuses of Kilburn/L&T / Havells/Siemens/Standard make and having capacity 30% extra of the operational rating as per IS-4064 : 1978 with upto date amendments, immediately after the Energy meter of the HPSEB. ICTP Switch: i)Make ii)Type iii)Capacity: 32 Amp

Providing MS Sheet, steel fabricated floor mounted switch board i/c angle iron post of suitable height and size ISA 40x40x6mm duly painted with steel sheet of 16 Gauge comprising and capable of mounting the following acccessories with all internal connections. Panel/Switch Board. i)Drawing ii)Layout Plan.

MCB of Kilburn/ L&T/MEI /GEC make and of suitable capacity on incoming feeder with or without initial oil filling as the case may be with neutral linked under voltage releases as per IS: 2516-1985 with upto date amendments. MCB i)Make ii)Type iii)Range iv)Capacity. 32 Amp.

ELCB of recommended make L&T/Havells as per IS ;2516-1985 with up to date ammendments, and of suitable range which should have control box , operating handle and trip / reset bush button on / off of indicators,reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. ELCB I) MAKE II) Type iii ) Range iv) Capacity. 25 Amp

Power factor meter of AE/L&T make as per relevent IS Code with upto date ammendments.i)Make ii)Type iii)Range

Frequency meter of AE/L&T make as per relevent IS Code with uptodate ammendments. .i)Make ii)Type iii)Range

Bus bar chamber of L&T / Havells make having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current one copper bar of half the rating of full length for neutral phase as per IS : 8084-1976 and IS: 11353-1985 read with BIS : 5578- 1985 with upto date ammendments. Bus Bar Chamber i)Type ii)Make iii)Rating

Three phase indicator lamps complete with toggle switches for individual motors as per IS: 3452 (P-I&II) with upto date ammendments. i)Type ii)Make iii)Capacity.

Pdg Hour run meter of recommended make of suitable capacity as per IS:722 (latest edition) i) Type ii) Make iii) Range

Capacitor of Mechell/BHEL/GEC/ L&T make as per IS ; 2834-1968 with upto date amendments,to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter/IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB Capacitor i) Type ii) Make iii) Range. 3 KVAR

Providing suitable DOL starter of L&T/Hevells/Kilburn make as per IS: 8544-1987 with upto date ammendments for squirrel cage/slip ring motor mounted on panel board with magnetic type overload release and dashpot, time lag, under voltage release with or without initial oil filling as the case mayu be with single phase preventor as per IS 1248 (P-V)-1983 with upto date ammendments.Star Delta Starter i)Type ii)Make Single phase Preventor i)Type ii)Make

Providing and fixing of double flanged cast iron sluice valve of kirloskar/Leader / Kartar/Kilburn /BHEL / GLAD / Foures / BIR make for suction pipe and capable of withstanding the normal seat pressure as per IS 780-1984 with latest ammendments i) 80 mm dia class PN1.00 cast iron.

Providing and fiximg of double flanged Cast iron Sluice valve of Leader/Kirloskar make of 65 mm dia for the delivery pipe of pump and capable of with standing the normal Seat Pressure as per BIS 14846 (Cast iron) as the case may be with latest ammendments. Sluice Valve i)Make ii)Class PN-1.00 iii)Seat pressure(MPa) iv)Material Cast iron

Providing and fiximg of double flanged Cast iron double flanged reflux valve of Leader/Kirloskar make of 65 mm dia for the delivery pipe of pump and capable of with standing the normal Seat Pressure as per BIS 14846 (Cast iron) with nuts and bolts and rubber insertion sheet of 52 kgf/cm2 complete in all respect.. Reflux Valve i)Make ii)Class PN 1.00 iii)Seat pressure(MPa) iv)Material Cast iron

Providing and fiximg of double flanged Cast iron Sluice valve of Leader/Kirloskar make of 80 mm dia for the delivery pipe of Rising Main and capable of with standing the normal Seat Pressure as per BIS 14846 (Cast iron) as the case may be with latest ammendments. Sluice Valve i)Make ii)Class PN-1.00 iii)Seat pressure(MPa) iv)Material Cast iron

Providing 100 mm dia circular dial pressure gauge of Prega/Precision make complete with all accessories such as stop cock, Copper tubing as per IS: 3624-1987 with upto date ammendments. i)Make ii)Range.

Installation of all above item as per the systematic drawing attached with the tender documents or as per the direction of Engineer-in Charge.The contarctor should ensure proper jointing of delivery pipe line of pump with the Rising main including all necessary accessories like increaser /reducer specials etc. as per site conditions and as per direction of the Engineer-in Charge.

Fixing of double flanged GMS piping work(layout to be approved by Engineer-in-Charge) for suction and delivery pipes suitable to pumps offered and common header as per the rising main respectively complete with all specials such as bends,Tees,Reducers Inceasers with companion flanges matching with the relevant specifications of the accessories as indicated in the Drawing i/c rubber/ asbestos gasket of 3 mm thickness as per IS : 2712-1979 and required number of Nuts and Bolts as per 1364-1983.-the pipes shall be as per relevent IS code and to withstand 1.5 times total head. (The pipe shall be issued free of cost at divisional store. However MS flanges will be provided by the firm)

i) Suction Pipe 80 mm dia. GMS pipe (M)

ii) Delivery Pipe 65 mm dia GMS pipe (M)

iii) Common Header 80 mm dia. GMS pipe (M) and will extend upto 5 metres from the outer wall of the pump house in the direction of Rising main of 80 mmm dia to be joined.

Providing and laying 3 core copper PVC Insulated armoured power cable(One cable carrying all the three phases) of suitable size and capacity to motors and all other elelctrical equipments as per IS: 1554(P-I)1988 or latest with upto date amendments of Seimen/Gloster/IEC/ICC/EICO/National/Grandlay make including all other accessories such as thimble, flelxible pipes, solder, nuts & bolts, cable glands etc. laid in pipes or trenches under floor.

Armoured Power Cable (A) Motor side (From Switch to Starter & Starter to motor) i) Size 4 mm2 ii) Make iii)Type iv) Capacity v) Core 3

(B) Supply Side (From meter of HPSEB to Bus Bar & Switch) i) Size 4 mm2 ii) Make iii) Type iv) Capacity v) Core 3

Providing and fixing double loop earthing with Copper wire/plate 600 mm x 600mm x3.15mm thick electrode complete with material such as thimble, Nuts & Bolts charcoal, salt as per IS:3043-1987 with upto date amenments GI plate & strip of suitable size for motors and other electrical equipments and digging ofpits etc. complete in all respect as per the direction of the Engineer-in-Charge. Copper flat 25x3mm above 50HP (Copper plate 600 mm x 600mm x3.15mm)

For WSS Slana Maslana

Supply of submersible pumping set of reputed make such as KSB/ Calama / BS/ Worthigton / Groundfos/ LUBI / Hindustan/ Sabar/ Seerex/Johnston / Amrut, confirming to latest relevent BIS . The pump should be fitted with free fine impellers of suitable alloys as per BIS ; 5659-1978 with upto date amendments, suitable for raw / clear water having greased packed bearing and shell with wound stator on motor side and with shaft protection on pump side ensuring better life for shaft conforming to BIS specifications. The pump shall be directly coupled to submersible motor of same as that of offered submersible pump make confirming to BIS ;9283-1979 with upto date amendments, totally dust and water proof for submersible pump, duly isolated from the pump by intermediate casing with double mechanical seal in oil chamber and grease packed, lubricated bearing and provided with stainless steel thrust bearing plate to withstand non vertical loads with minimum wear tear.It should also be fitted with a device to make up expantion of water with heating of motor. The pumpset should include water level guard i/c cable ,errection clamps, cable clips and depth gauge etc. and suitable for opertion on data given below. . Specifications offered a Pumps :- Specifications i) Make ii) Model iii) No. of stages iv) Manufacter's certificate to be attached Performance i) Discharge ii) Head iii) Efficiency of Pump a) Duty Head b) (+) 10% Duty Head. c) (-) 15% Duty Head d) Performance curve to be attached b) Motors; Specification i) Make ii) Model iii) B.H.P iv) Speed v) Insulation

Discharge, (Q) 4.11 LPS

Total Head ( H ) 58.23 Mts.

SWL in Tubewell 30.00 mtr. bgl.

R.L. point of discharge 406.20 mtr

Seasonal fluctuation + draught condition + bowl assembly.9 mtrs.

Drawdown in Tubewell 12.00 mtrs.

R.L. of lowest point of pump set installation 338.20 mtr

Static coulmn lift= 54.00 mtrs.

Rsiing Main Column pipe

Length = 10.00 mtrs Length 61.10 mtr

Dai 80 mtrs Dia 80 mm

Class GMS (M) Class GMS (M)

iv) Pumping hours 16 hours

v) Alititude of installations above M.S.L 475_mtr

vi) Characteristic of water

a) Temperature 25 Deg Cel.

b)Turbidity __________________JTU

c) Allkanity _________________mg/1Ca Co3

d) Size of solids _______________ mm

e) others

vii) Depth of T/well 91.50 mtr

viii) Dia of T/well assembly 175 mm

ix) Length of assembly pipe mtr

x) Dia of housing pipe 175 mm

xi) Length of housing pipe mtr

OPERATING CONDITIONS

i) Type of current A.C Three phases.

ii) Frequency 50 Cycles/ Sec.

iii) Rated Voltage 415+/-15% Volts

iv) System of earthing Double Loop earthing as per BIS 3843-1987 latest

v) Speed of Revolution __________________ RPM 2900

MOTOR

i) Ref to BIS code BIS 9283-1979 with upto date amendments

ii) Type of enclousre of motr As per BIS :4691-1985 (latest)

iii) Mechnical out put in HP

iv) Class of insulation : Class B The motor should be able to withstand intial current of 2.50 times the rated current for two minutes without suffering damages of permanet deformations

i) Ref to BIS code BIS 5659-1978 with upto date amendments

ii) Driver Type Electric drivern

iii) Operating Range -15%to +10% of Total head at duty point

iv) Deliver size of Pump ;---------- (to be quoted by tenderer)

Providing ICTP Main Switch with HRC fuses of Havell/L&Tmake and having capacity extra of the operational rating as per IS : 4864-1978I with upto date amendments. ICTP Switch: i) Make: ii) Type: iii) Capacity: 32 Amp.

Providing MS Sheet steel fabricated floor mounted switch board including angle iron post of suitable height and size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising and capable of mounting the following accessories with all internal connections. ICTP Switch: i) Make ii) Type (iii) Capacity : 32 Amp Panel /Switch Board. i) Drawing. ii) layout Plan.

MCB of L&T/Havells make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. MCB (1) Make (ii) Type iii) Range iv) Capacity. 32Amp

ELCB of recommended make L&T/Havells as per IS ;2516-1985 with up to date ammendments, and of suitable range which should have control box , operating handle and trip / reset bush button on / off of indicators,reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. ELCB I) MAKE II) Type iii ) Range iv) Capacity. 25 Amp

The voltage monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage,reverse phasing,overloading and phase voltage difference as per IS; 3842 ( Latest Edition ) Voltage Monitor Relay I) MAKE II) Type iii ) Range 0-500 amp

Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current one copper bar of half the rating of full length for neutral phase as per IS : 8084-1976 and IS: 11353-1985 read with BIS : 5578- 1985 with upto date ammendments Three phase indicator lamps complete with toggle switches for Bus Bar Chamber individual motors as per IS: 3452 (P-I&II) with upto date ammendments. i)Type ii)Make iii)Rating

Three phase indicator lamps complete with toggle switches for individual motors as per IS 3452 ( P- I&II) with upto date amendments. Three phase indicator

Capacitor of BHEL / GEC / L&T /Mecheil make as per IS ; 2834-1968 with upto date amendments, to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter / IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB. (i) Type (ii) Make (iii) Range 3 KVAR

Providing suitable DOL starter of L&T/BHEL make as per IS : 8544-1979 with'upto date amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic 'type overload release and dashpot, time lag, under voltage release with or without 'initial oil filling as the case may be with single phase prventor as per IS ;1248 ( P-5)1983 with up to date amendments.Single Phase Preventor i) Type ii) Make

Providing and fixing of double flange Cast Iron Sliuce valve of Leader / Kirloskarr make for the Column pipe of pump and capable of withstanding the normal seat pressure and as per IS 780-1984(Cast Iron) with latest ammendments PN 1.0 in Column pipe 80 mm dia.

Providing and fixing of double flanged swing type cast iron Reflux valve of Kirloskar/ Leader make having Bye pass arrangement on the Rising Main of the of the Pump and capable of 'withstanding normal Seat Pressure as per IS:5312-1984 (P-I) (Cast Iron) with latest ammendmets PN 1.00 in R/main 80 mm dia.

Providing pressure gauge of Prega/Precision make complete with all accessories such as stop cock, Copper tubing as per IS: 3624-1987 with upto date ammendments. Pressure Gauge i)Make ii)Range.

Supply of PVC 3 core jointless, flat water proof copper cable with copper conducter as per BIS 694-1998 latest with upto date amendments, suitable for the pumpsets offered from MCB to motor including all other electrical equipments/ accessories such as thimble, flexible pipe,solder, nuts and bolts, cable glands, clips etc, laid in pipes or trenches under floor . The type, size and make shall be subject to approval of HPSEB authorities. Submersible Cable i)Make. Finolex / Havells ii) Size. 4 mm Sq.

Lowering of GMS(M) Column pipe assembly 80 mm dia(MG) including MS flanges of Table 17 as per IS : 6392-1971 with upto date amendments, rubber/asbestos gasket of min. 3mm thickness as per IS 2712-1979 and required numbers of nuts and bolts as per IS ;1364-1983 . The Column pipe shall be as per relevent IS Code The Column pipe should be extended upto 5 mtr. beyond the outer wall of the pump house in the direction of Rising main . The Column pipe should be properly jointed with the Rising main including all necessary accessories like increaser / reducer, flanges, bends etc, including supporting clamps (2Nos.) at the top of T/well assembly, and as per the direction of Engineer - in - Charge. Column Pipe i) Size 100 mm dia. ii) Class GMS. iii) length. mtrs. Pipes shall be issued free of cost by the deptt at Divisional store at Barnoh).

Installation of all items appearing above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and laying copper PVC insulated 3 core armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS :1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster/IEC/ICC/EICO/National / Grandlay make including all othe accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor. Armoured Power Cable From Supply Side From meter of HPSEB to Bus Bar and Switch) i) Size 4mm Sq. ii) Make finolex /Havells iii) Type armound power cable iv) Capacity v) Core.

Providing and fixing double earthing with G.I. wire 8 SWG thick electrode complete with material such as thimble, nuts and bolts, charcoal, salt, copper strip as per IS 3043-1987 with upto date amendments for motors and other eletrical equipments and digging of pits etc. complete in all restect as per the dirction of the Engineer-in-Charge. i) G.I. wire 8 SWG

Centrifugal Pumping Machinery for WSS Slana Maslana

Providing horizontal spindle ,horizontal / radial split casing / end suction (back pull out arrangement). Single / double / multi stage centrifugal pump or combination of pumps in series / parallel of recommended make such as Mather and Platt /KSB/Beacon weir/Kirloskar / BE/ Jyoti/LUBI/GROUNDFOS/HINDUSTAN as per BIS IS 1520 1980 with upto date ammendments read with IS- 9137. 1978 or latest edition suitable for lifting water for under mentioned characteristic with Bronze impellers / priming funnels, casing ring and shaft sleeves of Bronze shaft of stainless steel with cast iron casing, coupled directly through a flexible coupling on a common cast iron/cast steel base plate (base plate to be framed from the manufacturers of the pumping unit only) to slipring/Squirrel cage screen protected drip proof induction motor/,motors of standard make such as Kirloskar /Bhel /Crompton/NGEF /GEC/ Seimens /jyoti/ LUBI/GROUNDFOS/ HINDUSTAN and suitable for operation on 415 (+/-5%) volts. 50 Cycles/Sec., 3 phase AC electric supply. The power of electric motor/motors should be at least + 10% in excess of the maximum power required by the pump/pumps in the Operation range of (+10%) and (-15%) of the duty point head. The motor/motors as per IS 325 IS 1978 with upto date amendments read with IS 900 1972 it should include cost of Bearing. Nuts, Bolts and painting etc. and should meet the following requirements.

Coupling

Base Plate

Discharge (Q) 4.11 LPS.

Total Head (H) 265.98 mtrs.

LWL In collection tank 403.65 mtr

b)R.L. of shaft 403.65 mtrs.

c)R.L. of discharge Pt. 618.10 mtrs.

d)Suction lift.

e)Discharge Head = 3.00 mtrs

Static Head 214.45 mtrs.

Rising main.

Length 2590 mtrs.

Diameter 80 MM

Class GMS (M)

Pumping hours. 8 hours.

Altitude of installations above M.S.L 450.00 mtrs.

Characteristic of Water

a)Temperature 20 Deg.Col.

b)Turbidity ________ JTU

c)Alloanity _________ mg/1 ca Co3

d)Size of solids __________ mm

e) Others.

Providing ICTP Main Switch with HRC fuses of Kilburn/L&T / Havells/Siemens/Standard make and having capacity 30% extra of the operational rating as per IS-4064 : 1978 with upto date amendments, immediately after the Energy meter of the HPSEB. ICTP Switch: i)Make ii)Type iii)Capacity: 90 Amp

Providing ICTP Main Switch with HRC fuses of Kilburn/L&T / Havells/Siemens/Standard make and having capacity 30% extra of the operational rating as per IS-4064 : 1978 with upto date amendments, immediately after the Energy meter of the HPSEB. ICTP Switch: i)Make ii)Type iii)Capacity: 63 Amp

Providing MS Sheet, steel fabricated floor mounted switch board i/c angle iron post of suitable height and size ISA 40x40x6mm duly painted with steel sheet of 16 Gauge comprising and capable of mounting the following acccessories with all internal connections. Panel/Switch Board. i)Drawing ii)Layout Plan.

MCB of Kilburn/ L&T/MEI /GEC make and of suitable capacity on incoming feeder with or without initial oil filling as the case may be with neutral linked under voltage releases as per IS: 2516-1985 with upto date amendments. MCB i)Make ii)Type iii)Range iv)Capacity. 63 Amp.

ELCB of recommended make L&T/Havells as per IS ;2516-1985 with up to date ammendments, and of suitable range which should have control box , operating handle and trip / reset bush button on / off of indicators,reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. ELCB I) MAKE II) Type iii ) Range iv) Capacity. 63 Amp

Power factor meter of AE/L&T make as per relevent IS Code with upto date ammendments.i)Make ii)Type iii)Range

Frequency meter of AE/L&T make as per relevent IS Code with uptodate ammendments. .i)Make ii)Type iii)Range

Bus bar chamber of L&T / Havells make having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current one copper bar of half the rating of full length for neutral phase as per IS : 8084-1976 and IS: 11353-1985 read with BIS : 5578- 1985 with upto date ammendments. Bus Bar Chamber i)Type ii)Make iii)Rating

Three phase indicator lamps complete with toggle switches for individual motors as per IS: 3452 (P-I&II) with upto date ammendments. i)Type ii)Make iii)Capacity.

Pdg Hour run meter of recommended make of suitable capacity as per IS:722 (latest edition) i) Type ii) Make iii) Range

Capacitor of Mechell/BHEL/GEC/ L&T make as per IS ; 2834-1968 with upto date amendments,to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter/IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB Capacitor i) Type ii) Make iii) Range. 7KVAR

Providing suitable Star Delta starter of L&T/Hevells/Kilburn make as per IS: 8544-1987 with upto date ammendments for squirrel cage/slip ring motor mounted on panel board with magnetic type overload release and dashpot, time lag, under voltage release with or without initial oil filling as the case mayu be with single phase preventor as per IS 1248 (P-V)-1983 with upto date ammendments.Star Delta Starter i)Type ii)Make Single phase Preventor i)Type ii)Make

Providing and fixing of double flanged cast iron sluice valve of kirloskar/Leader / Kartar/Kilburn /BHEL / GLAD / Foures / BIR /LP bandmake for suction pipe and capable of withstanding the normal seat pressure as per IS 780-1984 with latest ammendments i) 100mm dia class PN1.00 cast irn

Providing and fiximg of double flanged Cast steel Sluice valve of Leader/Kirloskar make of 65 mm dia for the delivery pipe of pump and capable of with standing the normal Seat Pressure as per BIS API 600 cast steel as the case may be with latest ammendments. Sluice Valve i)Make ii)Class ASA-300 iii)Seat pressure(MPa) iv)Material Cast iron

Providing and fiximg of double flanged Cast steel double flanged reflux valve of Leader/Kirloskar make of 65 mm dia for the delivery pipe of pump and capable of with standing the normal Seat Pressure as per API-6D (cast steel) as the case may be with latest ammendments complete in all respect.. Reflux Valve i)Make ii)Class ASA 300 iii)Seat pressure(MPa) iv)Material Cast steel

Providing and fiximg of double flanged Cast steel double flanged reflux valve of Leader/Kirloskar make of 80 mm dia for the delivery pipe of Rising main pump and capable of with standing the normal Seat Pressure as per API -6D as the case may be with latest ammendments complete in all respect.. Reflux Valve i)Make ii)Class ASA 300 iii)Seat pressure(MPa) iv)Material Cast steel

Providing 100 mm dia circular dial pressure gauge of Prega/Precision make complete with all accessories such as stop cock, Copper tubing as per IS: 3624-1987 with upto date ammendments. i)Make ii)Range.

Installation of all above item as per the systematic drawing attached with the tender documents or as per the direction of Engineer-in Charge.The contarctor should ensure proper jointing of delivery pipe line of pump with the Rising main including all necessary accessories like increaser /reducer specials etc. as per site conditions and as per direction of the Engineer-in Charge.

Fixing of double flanged GMS piping work(layout to be approved by Engineer-in-Charge) for suction and delivery pipes suitable to pumps offered and common header as per the rising main respectively complete with all specials such as bends,Tees,Reducers Inceasers with companion flanges matching with the relevant specifications of the accessories as indicated in the Drawing i/c rubber/ asbestos gasket of 3 mm thickness as per IS : 2712-1979 and required number of Nuts and Bolts as per 1364-1983.-the pipes shall be as per relevent IS code and to withstand 1.5 times total head. (The pipe shall be issued free of cost at divisional store. However MS flanges will be provided by the firm)

i) Suction Pipe 100 mm dia. GMS pipe (M)

ii) Delivery Pipe 65 mm dia GMS pipe (M)

iii) Common Header 80 mm dia. GMS pipe (M) and will extend upto 5 metres from the outer wall of the pump house in the direction of Rising main of 80 mmm dia to be joined.

Providing and laying 3 core copper PVC Insulated armoured power cable(One cable carrying all the three phases) of suitable size and capacity to motors and all other elelctrical equipments as per IS: 1554(P-I)1988 or latest with upto date amendments of Seimen/Gloster/IEC/ICC/EICO/National/Grandlay make including all other accessories such as thimble, flelxible pipes, solder, nuts & bolts, cable glands etc. laid in pipes or trenches under floor.

Armoured Power Cable (A) Motor side (From Switch to Starter & Starter to motor) i) Size 10 mm2 ii) Make iii)Type iv) Capacity v) Core 3

(B) Supply Side (From meter of HPSEB to Bus Bar & Switch) i) Size 6 mm2 ii) Make iii) Type iv) Capacity v) Core 3

Providing and fixing double loop earthing with Copper wire/plate 600 mm x 600mm x3.15mm thick electrode complete with material such as thimble, Nuts & Bolts charcoal, salt as per IS:3043-1987 with upto date amenments GI plate & strip of suitable size for motors and other electrical equipments and digging ofpits etc. complete in all respect as per the direction of the Engineer-in-Charge. Copper flat 25x3mm above 50HP (Copper plate 600 mm x 600mm x3.15mm)

Pawan Kumar Sharma Govt Contractor

Vivek Dhiman

Sushant Puri

M/S. Mast Ram Jaswal And Co.

SG Engineers and Consultants