Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
Tender Value
₹84.3 L
EMD Value
₹1.7 L
Closing Date
20 Nov 2026, 3:00 pm4d left
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Revenue
P.WAY
14 conditions · 3 needing a document upload
Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees. N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. (For details refer tender documents)
Similar nature of work means: Execution of any P.way related works.
32 conditions · 2 needing a document upload
The tenderer(s) should submit the BID SECURITY in acceptable form i.e. only through net banking or e-payment gateway or submitted as Bank Guarantee Bond from a Scheduled Nationalized bank of India or as mentioned in the tender documents. The Bank Guarantee Bond shall be as per Annexure- VI(A) and shall be valid for a period of 90 days beyond the bid validity period.( NOTE: For submission of Bid Security in the form of Bank Guarantee, all the procedures mentioned at Para-5 Bid Security (3)(i) to (vii) mentioned in the tender document should invariably be followed.)
Whether History sheet of tenderers (Annexure-2 of Part-II of Tender documents) uploaded duly filled in with supportive documents.
Whether the details of facilities available vis-a-vis the requirements mentioned in STR in a tabular/narrative form if you are not on the approved list of RDSO, if required in the Annexed Document, is submitted.
Whether, EACH PAGE of the copy of documents/certificates in support of credential is self attested/digitally signed by tenderer/authorised representative with signature, stamp & date.
Whether all the documents related "Mandatory Requirement", as applicable and mentioned in the bid documents are enclosed with the tender.
Please submit bank details as per enclosed Annexure-12 of Part - II of Tender Documents or photo copy of a "Cancelled Cheque". (For details refer tender documents)
Please submit Certificate of Familiarisation as per Annexure-1 of Part-II of Tender Documents. (For details refer tender documents)
Please submit required details as required from Annexure 2 to 11 of Part-II of Tender documents duly filled in and signed. Supportive documents/separate sheet are to be submitted, if required. Annex-2: HISTORY SHEET OF THE TENDERER, Annex-3: TECHNICAL EIGIBILITY CRITERIA, Annex-4: DETAILS OF CONSTRUCTIONS MACHINERIES, TOOLS & PLANTS, VEHICLES ETC. AVAILABLE (ON HAND AND PROPOSED TO BE UTILISED, Annex-5: DETAILS OF TECHNICAL AND OTHER PERSONNELS AVAILABLE ON HAND & PROPOSED TO BE ENGAGED. Annex- 6: DETAILS OF WORKS COMPLETED DURING PREVIOUS THREE FINANCAIL YEARS & CURRENT YEAR, Annex-7: DETAILS OF WORKS ON HAND, Annex- 8: DECLARATION REGARDING ASSOCIATION OF RAILWAY OFFICER (S) WITH TENDERER(S), A n n e x - 9 : LIST OF COURT CASES, Annex-10: LIST OF ARBITRATION CASES. Annex- 11: BROAD PLAN FOR EXECUTION OF THIS WORK. (For details refer tender documents)
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / Hindu Undivided Family (HUF)/ Limited Liability Partnership (LLP) etc. If it is NOT mentioned in the submitted tender that tender is being submitted on behalf of a Sole Proprietorship firm/Partnership firm/Joint Venture/Registered Company etc., then the tender shall be treated as having been submitted by the individual who has signed the tender . The tenderer(s) shall enclose the attested copies of the constitution of their concern and copy of PAN card along with the tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be. (for details refer tender documents) NOTE: Any document containing PAN number of the tenderer(s) shall also be considered in lieu of PAN card. However, if no document having mention of PAN number is uploaded, offer will be summarily rejected. (For details refer Tender documents)
For all tenders having advertised cost of Rs.10 lakh or above, the contractor shall have to submit the option to take payment from Railways through a letter of credit (LC) arrangement. The tenderer shall affirm having read over and agreed to the terms and conditions of the LC option. The option of taking payment through LC arrangement, once exercised by tenderer at the time of bidding, shall be final and no change shall be permitted, thereafter, during execution of contract. (The tenderer have to submit the option to take payment from Railway through a Letter of Credit arrangement) (For details refer Tender documents)
The list of personnel / organization on hand and proposed to be engaged for the tendered work. Similarly, list of Plant & Machinery available on hand and proposed to be inducted and hired for the tendered work. (For details refer tender documents)
Documents to be submitted as per Clause 14 of GCC-April 2022 in support of (a)Sole Proprietorship firm (b) HUF (c) Partnership Firm (d) Joint Venture (JV) (e) Company registered under Companies Act 2013 (f) LLP (Limited Liability Partnership) (g) Registered Society & Registered Trust. (for details refer tender documents) NOTE: Non submission of above documents will lead to summarily rejection of the offer.
Miscellaneous P. Way works at Bhubaneswar Coaching Complex Yard, Mancheswar C&W workshop and Mancheswar Exchange yard under SSE(P.Way)/BBS in the jurisdiction ADEN/BBS of Khurda Road Division.
e-tender-CENTKUR-187-2026~ECOR
e-tender-CENTKUR-187-2026
Open
Works - General
16 Months
Unknown (Unspecified Location)
₹0
₹1.7 L
30 Oct 2026
30 Oct 2026
6 Nov 2026
74 items across 2 schedules · ₹74,02,336.74 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | For Casual/Scattered Rail Renewal work | RM | 1400.00 | 33.06 | 46,284 |
| 2 | For Casual/Scattered Rail Renewal work | RM | 1400.00 | 34.99 | 48,986 |
| 3 | For location of work not involving deep screening | Each | 700.00 | 315.7 | 2,20,990 |
| 4 | For location of work not involving deep screening | TRM | 400.00 | 153.77 | 61,508 |
| 5 | Fish plates with 4 fish bolts. | Joint | 80.00 | 181.67 | 14,533.6 |
| 6 | Fish plates of 6 bolts. | Joint | 180.00 | 253.16 | 45,568.8 |
| 7 | Through renewal of Metal / GFN liners in running track condition after cleaning of rail foot at liner seat, greasing of liner, liner seat and sealing of liner contact area at rail foot including removing, cleaning & lubrication of ER Clip & Insert Eye and re-driving the same with contractor's grease graphite of approved quality with all lead & lift. | Sleeper | 3000.00 | 18.19 | 54,570 |
| 8 | Through Fitting Renewal (TFR) on PSC track, comprising of renewal of Grooved Rubber Pads, Liners and ERCs without damaging PSC sleepers. Scope includes removal of all fittings, cleaning of rail seat, rail flange at liner seats, and eye of Inserts with wire brushes and applying Grease Graphite Grade "O" (IS:408) to eye of insert and central leg of ERC with contractor's grease of Railway's specification, fixing all fittings in correct position and sealing liner edges with grease all complete including collection and stacking of released materials at nominated locations within SSE Jurisdiction as directed by Engineer-in-Charge. Note: All the fittings will be supplied at SSE/Stores/Depot. | Sleeper | 1000.00 | 24.75 | 24,750 |
| 9 | Through replacement of Grooved Rubber Sole pads(GRSP) on PSC sleepers duly removing the ERCs and liners and replacing the GRSP by just lifting the rail after cleaning the rail seat, refixing the liner and ERC after greasing of ERCs, liners and Liner contact area including sealing with Contractor's G r e a s e Graphite Grade 'O' (IS:408) duly cleaning of rust/scale of ERC, Metal /GFN liners & SGCI insert by using wire brush, scrapper/sand emery paper etc., with all contractor's labour, tools, plants including collection and stacking of released materials at nominated locations within SSE Jurisdiction and as directed by Engineer-in-Charge. Note: GRSP will be supplied at SSE/stores/depot. | Sleeper | 1500.00 | 22.44 | 33,660 |
| 10 | For 1.00m long fishplates | Joint | 250.00 | 102.51 | 25,627.5 |
| 11 | For 610 mm long fish plates. | Joint | 100.00 | 69.94 | 6,994 |
| 12 | Lubrication of Elastic Rail Clips on PSC sleepers with contractor's grease, conforming to Railway's specifications, labour etc. complete as per procedure prescribed in latest edition of IRPWM. | ERC | 20000.00 | 2.96 | 59,200 |
| 13 | Lubrication of ERCs and its liner contact area by removal of ERCs and Metal / GFN liners in rail panel, cleaning of rust / scale of ERC, Metal / GFN liners & SGCI insert by using wire brush, scrapper / sand emery paper etc supply and application of graphite grease, as prescribed by Railway for under side of liners & corresponding area of rail foot & SGCI insert with ERCs and re-fixing the same as per procedure prescribed in latest edition of IRPWM with contractors grease and all other tools & plants complete and as directed. Note: Each ERC in this item shall constitute 1 ERC and its Liner Contact area. | ERC | 6000.00 | 4.08 | 24,480 |
| 14 | Removing seized ERC from SGCI inserts of existing track by using suitable approved chemicals and re-fixing after greasing of insert eye and ERC with Contractor's grease of specified quality as per provisions of IRPWM, as directed by Engineer in-charge. Note: 1.List of Seized ERC along with location shall be prepared after inspection of SSE/P.Way and marked prior to execution of this item. 2. Due care shall be taken to avoid any damage to the sleeper 3.A penalty of 50% of the basic cost of new sleeper in nearest sleeper factory shall be levied on each, if SGCI insert is broken or sleeper gets cracked in the process. | ERC | 800.00 | 59.81 | 47,848 |
| 15 | Lubrication of gauge face of rail on curves, cross overs, points & crossings, turn-in curves and at locations as required with contractor's grease graphite grade "O" IS 408 and as directed. | RM | 5000.00 | 3.58 | 17,900 |
| 16 | By using Contractor's Grease Graphite | Each | 3000.00 | 32.71 | 98,130 |
| 17 | GRSP | Each | 600.00 | 19.21 | 11,526 |
| 18 | ERCs | Each | 1000.00 | 6.42 | 6,420 |
| 19 | Metal/GFN Liners | Each | 1000.00 | 4.28 | 4,280 |
| 20 | Renewal of seized Plate/Rail screws on PSC Sleepers by using gas or any approved methods, duly drilling holes in broken screw and removing existing screw pieces from the holes along with existing dowels and fixing new contractor's dowels (procured from RDSO approved sources) and grouting around dowel with Epoxy materials of approved specification and refixing new Railway's rail/Plate screws duly greasing the s c r e w w i t h specified grease with all contractor's materials, consumables, tools & plants, labour with all lead, lift. Note: 1.Seized screws shall be identified and marked by JE/P.Way and verified at minimum SSE/P.Way In charge) level. 2. Due care shall be taken to avoid any damage to the sleeper 3.A penalty of 50% of the basic cost of new sleeper in nearest sleeper factory shall be levied on each, if sleeper gets damaged in the process. | Each | 400.00 | 290.31 | 1,16,124 |
| 21 | Rail section of 52Kg and above | Each | 150.00 | 112.21 | 16,831.5 |
| 22 | Sleepers up to 2.85 m length | Each | 44.00 | 563.99 | 24,815.56 |
| 23 | Sleepers of length more than 2.85 m and up to 4.20 m | Each | 66.00 | 776.72 | 51,263.52 |
| 24 | Sleepers of more than 4.20 m length | Each | 24.00 | 1,223.68 | 29,368.32 |
| 25 | 1 in 8½ Turnout | Set | 3.00 | 3,557.04 | 10,671.12 |
| 26 | 1 in 8½ Switch Assembly | Set | 3.00 | 12,535.87 | 37,607.61 |
| 27 | For 1 in 8.5 Turnouts | Set | 10.00 | 4,181.08 | 41,810.8 |
| 28 | Turnout sleepers of length up to 2.85 m | Each | 200.00 | 127.88 | 25,576 |
| 29 | Sleepers of length more than 2.85 m and up to 4.20 m | Each | 200.00 | 153.45 | 30,690 |
| 30 | Sleepers of length more than 4.20 m | Each | 200.00 | 166.24 | 33,248 |
| 31 | Depth of 200 mm below bottom of sleeper - For Plain Track : | TRM | 150.00 | 433.64 | 65,046 |
| 32 | Depth of 200 mm below bottom of sleeper for Turnouts | TRM | 130.00 | 693.83 | 90,197.9 |
| 33 | Lifting and packing for regrading the existing PSC sleeper track to required height / level in stages not exceeding 75mm or part thereof at a time, providing permissible ramp for the track, insertion of moorum / sand / stone ballast uniformly under the existing track and placing the same to safe approved gradient, gauge, cushion including levelling and one round of through packing to allow train movement at restricted speed of 30 kmph for a specified length with all leads & lifts and fixing, marking, painting rail level pegs at every 30m interval. Note: Lifting of track shall be done in stages as per procedure prescribed in latest edition of IRPWM to get the proposed final level as per approved working profile, as directed by Engineer in- charge. | TRM | 4500.00 | 165.82 | 7,46,190 |
| 34 | Boxing and profiling of ballast as per procedure prescribed in latest edition of IRPWM including cess dressing on both sides of track. The work will include removing excess ballast from track and putting the same in crib and shoulder by leading to a maximum of 50m including crossing of track, deweeding on ballast section etc and as directed by Engineer-In charge. | TRM | 6000.00 | 24.39 | 1,46,340 |
| 35 | For 60 Kg/60EI-R260 grade Rail, Single shot crucible fitted with Automatic Tapping Thimble Technology, 3 pieces Mould (Zircon washed) and Compressed Air Petrol heating technique. | Each | 55.00 | 1,741.94 | 95,806.7 |
| 36 | For 52 Kg - 90 UTS or 52 Kg 72UTS Rail, Single shot crucible fitted with Automatic Tapping Thimble Technology, 3 pieces Mould (Zircon washed) and Compressed Air Petrol heating technique. | Each | 20.00 | 1,741.94 | 34,838.8 |
| 37 | For PSC sleeper Track with Sleeper Density of 1540 Sleepers/Km or more | TRM | 9000.00 | 96.79 | 8,71,110 |
| 38 | For PSC Sleeper | TRM | 2500.00 | 82.96 | 2,07,400 |
| 39 | For PSC Sleeper Track with Sleeper Density of 1660 | TRM | 300.00 | 127.76 | 38,328 |
| 40 | For PSC Sleeper Track with Sleeper Density of 1660 | TRM | 300.00 | 98.28 | 29,484 |
| 41 | Packing of isolated loose PSC sleepers on plain track below the bottom of the sleepers and surrounding through out its length duly opening two galas on either side of the renewed sleepers and packing the sleeper to bring the track to normal speed including gauging, aligning, squaring of sleepers and sectioning of ballast to the required profile with all contractor's labour, tools and plant etc. including all lead and lift and crossing of tracks where ever necessary complete and as directed by the Engineer-in-charge. | Sleeper | 3000.00 | 75.21 | 2,25,630 |
| 42 | For PSC sleeper Track with Sleeper Density of 1540 sleepers/Km or more | TRM | 5000.00 | 164.96 | 8,24,800 |
| 43 | Removing weeds & bushes in ballast section and cess up to 3.95m from centre line of track in mid section & station yard, as specified by Engineer in-charge including disposal of branches, bushes outside cess/yard. | TRM | 60000.00 | 13.8 | 8,28,000 |
| 44 | 60 Kg - 110/90 UTS - Outside Track | Each | 50.00 | 303.09 | 15,154.5 |
| 45 | 52 Kg - 90 UTS - Outside Track | Each | 20.00 | 277.35 | 5,547 |
| 46 | 60 Kg - 110/90 UTS - On Running Line | Each | 300.00 | 384.24 | 1,15,272 |
| 47 | 52 Kg - 90 UTS- On Running Line | Each | 30.00 | 310.55 | 9,316.5 |
| 48 | Outside Track | Each | 60.00 | 52.94 | 3,176.4 |
| 49 | On Running Line | Each | 450.00 | 68.3 | 30,735 |
| 50 | Drilling holes of specified size for bond holes with 7.2mm dia drill twist to correct spacing and location on 60kg/52kg rails on cess or under traffic block with contractor's tools and plant, equipment, consumable, labour etc complete as directed by the Engineer in charge at site. | Each | 50.00 | 41.16 | 2,058 |
| 51 | I n Wagon where mechanical handling is possible and traffic block is not required or in Truck/trailer. | MT | 20.00 | 128.97 | 2,579.4 |
| 52 | For lead up to 500 metre. | MT | 125.00 | 356.93 | 44,616.25 |
| 53 | For lead up to 500 metres | MT | 120.00 | 277.85 | 33,342 |
| 54 | Lead beyond 20 Km and up to 30 km | MT | 30.00 | 231.42 | 6,942.6 |
| 55 | From Truck / Trailer | MT | 30.00 | 136.19 | 4,085.7 |
| 56 | Rails, switches, crossings, SEJ, Glued Joints, Check Rails etc. | MT | 75.00 | 382.22 | 28,666.5 |
| 57 | All type of PSC sleepers | MT | 150.00 | 414.79 | 62,218.5 |
| 58 | Manufacturing, supplying and fixing Curve Indicator / Point Indicator / SEJ Boards to be provided at various locations on formation, made out of MS sheet 2mm thick of size 450mm x 300mm duly fixed with MS frame of 25mm x 25mm x 3mm angle welded to 50mm x 50mm x 3mm MS angle, 1000mm long post split and bent 100mm at bottom end with all lead & lift as per specification and including painting of details with enamel paint, as directed by Engineer in-charge (Earthwork & concreting will be paid separately) | Each | 50.00 | 1,066.15 | 53,307.5 |
| 59 | 18 mm dia. | Each | 2.00 | 1,906.23 | 3,812.46 |
| 60 | 28.75 mm dia. | Each | 10.00 | 3,881.34 | 38,813.4 |
| 61 | Supplying and spraying in specified proportion Weedicide Chemical, capable to kill entire weed on track / cess / embankment with all labour, material, tools & plants etc. complete job in all respect. Scientific name of the chemical is Isopropylamine Salt of Glyphosate, in which active ingredient is Glyphosate (41%), colour is light amber to brownish, very low in toxicity and has favourable environmental characteristics. It will be ensured that no weed growth occurs up to six months period, otherwise re- spraying shall be done by the contractor free of cost. | Sqm | 361140.00 | 0.51 | 1,84,181.4 |
| 62 | JCB Backhoe Loaders 3DX Plus or similar with minimum 1.10 cum bucket capacity | Hour | 30.00 | 802.46 | 24,073.8 |
| 63 | Hydra or similar tyre mounted Pick-n-Carry crane of 12T capacity for misc. works of handling of material | Hour | 30.00 | 1,134.57 | 34,037.1 |
| 64 | Tractor with Trolley for local transportation or other misc. works. | Hour | 30.00 | 356.23 | 10,686.9 |
| Schedule total | ₹61,87,056.64 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TenderCondition-GCC25.05.2026.pdf
ATTACHMENT
SpecialConditionsforP-WayRelatedWorks.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .