Installation of Street light, high mast light and Divider in Built-up area between Ch. 32/500 to 50/500 on NH-162A

Earthwork in cutting with lead up to 50 metres and lift up to 1.50 metres, including finishing of formation to the required camber and grade, and leveling and dressing of the disposed soil, complete as per specifications.

Providing and laying plain cement concrete of M-15 grade using 20 mm nominal size graded stone aggregate, mechanically mixed and vibrated, in foundation up to a depth of 1.50 m below ground level and/or up to 1.50 m above ground/bed level, including all materials, labour, compaction, curing, tools and plants, complete in all respects.

Providing and fixing Precast Concrete Interlocking Paving Blocks, 80mm thick, Medium traffic category, M-40 grade designation, manufactured on fully computerized automatic vibro-pressed machine as per IS:15658-2006, laid on 50mm average thick bed of coarse sand with joints filled with fine sand, laid on compacted sub-base, inclusive of earthwork in cutting of B/T or WBM road and disposal of unserviceable material with all leads/lifts

Providing and laying Reinforced Cement Concrete (RCC) M20 mix with 20 mm nominal size stone aggregate, mechanically mixed and vibrated, for bed plates, excluding steel reinforcement but including centering and shuttering, laid in position, complete as per MoRTH Specifications, Clause 1000/700.

Earth work in excavation, including stacking/disposal of surplus material with all lifts and lead up to 50 meters, exclusive of compensation of earth [MoRTH specification : Clause 301 to 305] In ordinary Soil Mechanically by power shovel, including mechanical loading and carriage up to 50m.

Providing and laying cement concrete of M-25 grade using 20 mm nominal size graded stone aggregate, mechanically mixed and vibrated, in foundation and plinth, including compaction, curing, centering and shuttering, and all materials, labour, tools and plants, complete in all respects. Mix proportion: 1:1:2 (1 cement : 1 sand : 2 graded stone aggregate).

Providing and laying Steel reinforcement at any level in foundation complete as per drawing and technical Specification.[MoRTH Specification : Section: 1600(N)] HYSD bar reinforcement

Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces on old surface

Supply and erection of Galvanized Iron pole with galvanizing done in single dipping (Average coating thickness Minimum 65 Microns) Swaged tubular pole conforming to IS: 2713-1980 (part I to II) with galvanised base plate, the pole shall be made from steel tube & Pipe (IS:1141, Fe 410) including excavation of the pit and filling the same with C.C. of M-20 grade (1:1.5:3) from base plate to 50 cm above ground level, with the help of steel frame not less than 40 cm dia up to 114.3mm outer dia and 50 cm beyond 114.3mm outer dia around the pole. Duly finished with cement plaster, earthing terminals, cable entry with 32 mm dia. 'B' class GI cable sleeves complete as required, of following height & designation (see Table P-03 for specs). HEIGHT/DESIGNATION: 9.0 Mtr. (410 SP-28).

Providing & Fixing of IK08, IP-66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing and secondary lens on each LED/integrated lens diffuser without cover & should be High power LED of 3 to 5 watt each. The System efficacy >=135 lm/wt and integrated metal case potted driver has a unique BIS R number (as per IS 15885) with Input Voltage AC 120-270V, High voltage Cutoff @>=300V AC & Low Voltage cutoff @>=90V AC with Auto resetting Safety, Power Factor >0.95, driver Efficiency >85%, THD(I) <10%, Humidity 10-90% RH, Working Temp -5°C to 45°C, LED driving output current <750mA. Luminaire shall be BIS certified (Fitting & driver both have separate BIS R number) and Trade mark certified. Life Expectancy >=50,000 burning hrs with min. 70% lumen maintained, CRI >70,CCT 5700K ±355K. Surge protection min >=4KV internal and 10KV external inside driver compartment; phase-to-phase protection of 440V for 4 Hrs as required. RATING: Minimum lumen output 8,100 lm.