SPECIAL REPAIRS TO MD ACCN BLDG NO P-77 TO 80, PHILLORA ENCLAVE AND ADDN/ALTN TO BLDG NO B-41, B-51, B-57, B-60 AND B-70 AT PATIALA MIL STN

Amount

S&F Built in steel cup board with pressed steel frame of size 75 mm x 45 mm x 1.25 mm thick with pressed steel shutter 01 mm thick Godrej pattern fixed to masonry wall with hold fasts, made out of 25 x 3 mm flat iron including spray painting with two coats of synthetic enamel paint over one coat of red oxide primer all around on steel surfaces including taking down old existing wooden cup board including cutting hole making good disturbed portion in CM (1:3) to receive fresh PCC all as directed and shown on Drg. No. 178 sheet 1/4 to 4/4 dt12.05.2001. (Shelves shall be measured and paid for separately).

Demolition of brick work including all quoins arches pillars etc built in cement mortar complete as specified and directed.

M&L for brick work in cement mortar (1:6) using sub class 'B' bricks staight or curved on plan exc 6.0 m mean radius complete as specified and directed.

M&L PCC 1:7:12 type F-2 using 40 mm thick brick aggregate as in filling of sunken portion complete as specified and directed.

M&L 25mm thick PCC 1:2:4 type B0 using12.5 mm graded stone aggregate as in sunken floor complete as specified and directed.

M&L Rendering 15mm thick on concrete surface in Cement mortar 1:3, finishing surface mixed with integral liquid WPC as manufacturer's instruction as in sunken portion complete as specified & directed.

Taking down cement plaster on brick walls built in cement mortar including raking out joints and concrete surfaces as in wall or ceiling etc. including hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L Rendering 15mm thick on brick or concrete surface in Cement mortar 1:4, finishing surface w/o using extra Cement, mixed with integral liquid water proofing compound complete all as directed and specified.

Supply only integral water proofing compound.

M&L 10mm thick cement plastering in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed.

M&L 5 mm thick cement plastering in cement mortar 1:3 on fair faces of concrete ceiling surfaces finished even & smooth without using extra cement complete all as specified and directed.

Material and labour for efflorescence treatement to wall surface comprising of the following specifications, complete all as specified and directed by Engr-in-Charge :- (i) Cleaning of wall surface with mechanical means i.e. steel wire brush/air blower etc. and remove all loose /unsound material,dirt,dust etc and allow air dry for 48 hours. (ii) Washing of wall surface with HCL acid with dilution of water in ratio 1:50 till saturation point and allow air dry for 24 hours. (iii) Primer the wall surfaces with URP mixed in the proporation 1:1 (URP Cement) as bonding agent and cure the surface adequately for at least 48 hours. (iv) Prepare PMM consists of 1 part of cement +3 part sand + 15% URP+ 20% water (% by weight by cement) . After two days apply two coat URP mix with cement by the ratio 1 Kg URP : 1.5 Kg cement at the interval of 6 hour. (v) Apply two coat of Pidifin 2 kg( Two component ready to use pack) at the interval of 6 hours. After second coat of Pidifin 2K , sand shall sprinkle on the coated surface as sand plaster and allow air curing for 4 days. complete all as directed. Note -(i) Efflorescence treatemnt shall be got done from the agency approved by the GE. (ii) Contractor shall give written gurantee for five year against efflorescence treatement carried out. (iii) Gurantee Money @5% of efflorenscence treatment shall be kept reserve for a period of two years and shall be released on successful expiry of defect liability of effloresence treatment. This Guarantee money shall be in addition to performance security in terms of condition 19 of IAFW-2249.

Complete removal of existing treatment of any type/description such as distempering work, internal emulsion etc from internal surfaces of walls & ceiling with mechanical means/grinder complete all as specified and directed.

Applying acrylic wall care putty in external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving exterior painting complete all as specified and directed. Make of wall Putty : JK wall Putty / Birla Wall care Putty / Bison Wall Putty. Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further external finishes. Please note that the further external finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order.

Applying 02 coats of exterior emulsion paint (light shade) by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer complete all as specified and directed.

Applying 02 coats of interior emulsion paint (light shade) on wall surfaces over & including a coat of interior wall primer complete all as specified and directed.

Preparation of surfaces and applying 02 coats of interior emulsion paint (white shade) on ceiling surfaces of wall or false ceiling over & including a coat of interior primer complete all as specified and directed.

M&L for preparing new plasterd surfaces of ceiling and applying three coat white wash complete all as specified and directed.

M&L for preparing old plasterd surfaces of ceiling and applying one coat white wash complete all as sepcifeid and directed complete.

M&L for preparing new plastered surfaces of walls and applying three coat whitewash complete all as specified and directed complete.

M&L for preparing old plastered surfaces of walls and applying one coat whitewash complete all as specified and directed complete.

Demolition of cement concrete in floors and pavings n. exc 15 cm thickness below or above ground level, complete all as specified and directed.

M&L 50mm thick, PCC 1:3:6, type C-1 using 20 mm graded stone aggregate, as in plinth protection finished even & fair without using extra cement complete all as specified and directed .

M&L 25mm thick, PCC 1:2:4, type B-0 (using 12.5mm graded stone aggregate), as in floor, sub base finished fair & even without using extra cement complete all as specified and directed .

Dismantling floor hearth or wall tiling including cement mortar bedding, removing serviceable tile to store and rubbish off the premises.

M&L for single charge, Ceramic, stain & scratch resistant, joint free, premium quality coloured tiles 600 X 600 mm and 9-10 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed with adhesive of Sika (Ceram Grey) @ 5 Kg/sq.m and pointed in white or coloured cement to match, in floors etc. over & including 15 mm thick screed in cement mortar (1:6) over and pointed in white cement with pigment to match the colour of tiles complete all as specified. Make : Johnson (Daisy SF/Gloria SF) or equivalent from Kajaria/Somany as approved by AO

M&L for single charge,Ceramic, stain & scratch resistant, joint free, premium quality coloured tiles 600 X 100 mm and 9-10 mm thick in any pattern of light & dark tiles as approved,on vertical surfaces such as in skirting/dado etc ,length of each unit not less than 600 mm and height not more than 150mm, set and jointed with adhesive of Sika (Ceram Grey) @ 5 Kg/sq.m over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified. Note : Skirting should be flushed with the wall plastering. Make : Johnson (Daisy SF/Gloria SF) or equivalent from Kajaria/Somany as approved by AO

M&L for non-skid ceramic joint free premium quality coloured tiles 400 X 400 mm and 6-7 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 15 mm thick screed in cement mortar (1:6) over and pointed in white cement with pigment to match the colour of tiles complete all as specified. Make : Johnson (Digital HD Tiles) (Barstow or Sobaro Deep) or equivalent from Kajaria/Somany as approved by AO

M&L for ceramic glossy finish, joint free premium quality coloured tiles 450 X 300 mm and 8-9 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified. Note : Dado should be flushed with the wall plastering. Make : Johnson (Digital HD Tiles) (Barstow Dark/Light/HL or Sobaro Deep/Bright/Bright Decor) or equivalent from Kajaria/Somany as approved by AO

M&L for non-skid ceramic joint free premium quality coloured tiles 300 x 300 mm and 6-7 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 20 mm thick screed in cement mortar (1:4) over and pointed in white cement with pigment to match the colour of tiles complete all as specified. Make : Johnson (Digital HD Tiles) (Barstow or Sobaro Deep) or equivalent from Kajaria/Somany as approved by AO

M&L for Baroda Green marble, machine cut as in shelves/steps/cills/jambs/skirting/border only in tile flooring and the like works and flooring etc, 20 mm thick including bull-nose the front length, set and jointed in cement slurry over & including screed of 15 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type granite polishing complete all as specified. Note : Single piece should be used in steps/cills/jambs/shelves.

M&L for 20mm thick granite (of telephonic black) work (table rubbed and polished)in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment and complete polishing and bull nosing at reqd places and including and over 20mm thick screed bed in CM 1:4 complete.

Machine cut kota stone slab as in steps of staircase and midlanding portion incl & 18-20 mm thick, set and jointed in cement slurry including border of 100mm wide kota of 18-20mm thick as per pattern approved over & including screed of 20-22 mm thick in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type granite polishing complete all as specified. Note : 1. All the edges of slabs shall be grinded/cutted at the right angle before laying, so that paper thin, smooth jointing to be obtained. 2. The colour of the slabs shall be uniform.

M&L for providing and Laying Premium (1st) quality straight edge, ceramic tiles WA value between 3% to 6% , flexural strength greater than 22N/mm², scratch resistance on mohs scale greater than 4 and crazing resistance of 2 cycles in area of each tile exceeding 0.06 sqm but not exceeding 0.16 sqm in floor, 8 to 10 mm thick in floors etc. in any shade and design/pattern of light & dark tiles etc as approved matching with wall tiles, set & jointed in neat cement slurry & pointed in matching colored polymer cement based grout to match over complete all as specified and directed by Engr-in-Charge.

M&L machine pressed rubber moulded ISI marked precast cement concrete interlocking paver block any shape and size and of with grey cement and pigment tiles confirming to IS-15658-2006 of 60mm thickness M-35 grade and including filling of interstices with fine sand complete all as specified.

M&L for 25 mm thick sand cushion under paving block including watering and consolidation for interlocking tiles all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 (using 40mm graded stone agg) as in sub base of path or hard standing complete all as specified and directed.

Dismantling loose/disintegrated portion of RCC Chajjas, bands, shelves, beams, column or slab and similar work including support if required and stitching of cracks with MS U clamps of 8mm dia @ 150mm c/c with inserting concrete block strecthner with cement mortar 1:3 mixed with adhesive chemical (polymer based) and reinforced with PVC chicken mesh including form work where ever required and finished with 10mm thick plastering in CM 1:4 finished even & smooth without using extra cement including preparation of surfaces to receive finishes complete all as specified and directed.

Taking down chowkhats or frames of any description exc 1.5 Sqm and n. exc. 4 sqm each (without taking off shutters from the frame) including cutting hole to size for receive fresh PCC of hold fast and making good the disturbed surface same complete all as specified and directed.

Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified.

S&F Pressed steel frames made of MS sheet of size 105x60mm and 1.20 mm thickness for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified,

S&F Pressed steel frames made of MS sheet of size 125x60mm and 1.20 mm thickness for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified,

S&F factory made ISI marked flush door shutters 35mm thick, BWP conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters incl two coat of synthetic enamel painting over a coat of pink primer complete all as specified and incl supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm - 1 No per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 No per leaf (f) Prepration of surface and two coats of synthetic enamal paint over a coat of pink primer

S&F 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-1 section 8 clause 8.20(a), kiln seasoned and chemically pressure treated all as specified including stainless steel 304 Grade wire cloth (0.36mm nominal dia of wire and average width of aperture 1.40mm) incl two coat of synthetic enamel painting over a coat of pink primer complete all as specified and including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x300mm - 1 No per leaf (e) Prepration of surface and two coats of synthetic enamal paint over a coat of pink primer

M & L for Solid PVC door frames of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube, and edges will be painted to match with printed sheet, supply & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

M & L for Factory Made Solid PVC Moulded flush Door Shutter, 28 to 30mm thick(stiles), with 2, 4, or 6 raised panel design with light colour matching to frame printed 4mm thick Moulded PVC Sheet on the front face & 4mm plain colour PVC sheet on back face, supplying & fixing in frame at site complete all as specified and directed by Engineer-in-Charge.

M & L for Powder coated (Minimum thickness of powder coating 50 micron ) Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer-in-Charge.

M & L for Aluminium window (Casement & sliding) and ventilator shutters with 50 micron powder coating double shutters made and to be fixed with EPDM gasket to render the glazing, air and water tight etc. and aluminium beeds in inner shutters complete fixed in all respect as specified & directed by Enginner-in-Charge. Note :- EPDM gasket shall be measured as supply only separately

S&F 4mm thick tinted glass for aluminium windows including EPDM gasket to render the glazing, air and water tight etc and power coated aluminium beeds 20 mm size complete all as specified and directed by Engr-in-charge

S&F stainless steel wire gauge 0.36 mm nominal dia of wire and average width of aperture 1.40mm to be fixed in Powder coated aluminium windows/ ventilators etc complete all as specified and directed by Engr-in-charge

S&F stainless steel (304 grade) finished butt hinges 75mm complete all as specified and directed.

S&F powder coated aluiminium tower bolt 100mm long complete all as specified and directed by Engr-in-charge.

S&F powder coated aluminium handles 150mm complete all as specified and directed by Engr-in-charge

S&F powder coated aluminium hook and eye of suitable length adjustable to aluminium window shutters complete all as specified and directed by Engr-in-charge

S&F 4mm thick frosted glass fixed to aluminium ventilator including necessary EPDM gasket to render the galzing, air and water tight etc and powder coated aluminium beeds 20mm sized complete all as specified and directed by Engr-in-charge

S&F stainless steel tubing of 25 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets/finials fancy type, stops fixed with ss screws etc all as specified & directed as in repair . Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered.

Taking up or down steel tubing and connections incl cleaning for refixing or removing to store yard of size 15mm bore.

S&F Steel water tubing medium grade 15mm bore galvanised with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed.

All as per Serial Item No 58 abovehere-in-before but except water tubing (Old serviceable tubing as retrieved vide item above shall be reused under this item).

Taking up or down steel tubing and connections incl cleaning for refixing or removing to store yard of size 20mm bore.

S&F Steel water tubing medium grade 20mm bore galvanised with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed.

All as per Serial Item No 61 above here-in-before but except water tubing (Old serviceable tubing as retrieved vide item above shall be reused under this item).

S&F flushing cistern of PVC 10 ltr. cap. with dual flushing system, valveless syphonic action type, , low level, white/ivory/off white with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete in all respect all as specified. Make : Hindware (Sleek Essence Dual Flush) or equivalent from Parryware/Cera as approved by AO

M&L for Vitreous china squatting pan of Orissa patten size 580mm x 440mm white with (C I 'P' trap long size) joint run and lead front or back inlet with integral footrest including connection to trap and to flushing pipe,anti-syphonage pipe, etc, fixed in repair complete and making good to floor in CM 1:3 all as directed and specified.

S&F vitreous china premium/1st quality wash basin (under counter), off white, size 580x430 mm including all accessories as recommended by manufacturer incl. CP bottle trap 32 mm with inlet and outlet screwed for pipe or connections incl all necessary accessories for fixing, packing, union and incl 32mm brass CP waste coupling and completein fixed in position in all respect as per manufacturer's instructions and taking down existing of any description/size all as specified and directed by Engineer in Charge. Note : The items for counter will be measured and paid seperately. Make : Cera / Jaquar/Kohelr/Hindware.

Vitreous china wash down water closet pan including seat cover (Pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), (Fixed in repairs) P or S trap, including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge. Make : Make : Cera / Jaquar/Kohelr/Hindware.

S&F Health faucet (ABS Body) with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. Make : Cera / Jaquar/ Kohelr/ Hindware.

S&F Concealed Stop Cock, fancy type chromium plated with long shank and cu[p, exposed part kit with all flange, fitting sleeve, operating lever, adjustable wall flange and including regular brass body of concealed stop cock suitable for 15mm line with protection cap fixed in position complete all as specified and directed. Make : Cera / Jaquar/Kohelr/Hindware.

S&F Angular Stop Cock with wall flange, fancy type chromium plated cast copper alloy screwed down, high pressure, screwed ends for 15mm bore of iron pipe or for union and fixed in position complete all as specified and directed. Make : Cera / Jaquar/Kohelr/Hindware.

S&F towel rack CP 60 cm long with lower hanger / hook fixed in position complete all as specified and directed.

S&F single liver basin mixer with popup waste system and 450 mm long braided hoses, fancy type, cast copper alloy, with capston head chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts screwed for 15 mm bore of iron pipe complete all as specified and directed by Engineer in Charge. Make : Cera / Jaquar/Kohelr/Hindware.

S&F single lever Sink mixer with swinging spout with connecting legs and wall flanges, wall mounted fency type chromium plated cast copper alloy screwed down high pressure, screwed ends for 15mm bore of iron pipe or for union and fixed in position complete all as specified and directed by Engineer in Charge. Make : Cera / Jaquar/Kohelr/Hindware.

S&F wall mixer assembly, brass chromium plated, comprising of centre outlet tap, double inlet for hot and cold water with connecting legs and wall flange fancy type suitable for 15 mm tubing fixed in position complete all as specified and as per sample. Make : Cera / Jaquar/Kohelr/Hindware.

S&F Stainless Steel sink with drainage board, AISI 304 quality grade, 1.00 mm thick, glossy finish, for kitchen with plugs washers and CP waste coupling of 32mm dia and including cantilever cast iron brackets, connecting union, etc, overall size 915mm x 460mm / 928mm x 458mm with bowl size 410 mm x 355mm x 185mm / 430mm x 355mm x 200mm including strainer of minimum 110 mm dia and making good disturbed portion in cement mortar 1:3 or PCC 1:2:4 type B0 complete all as specified and directed by Engineer in Charge.

S&F PVC (HDPE) SWR, 40 mm bore, single socketed in any length with rubber ring joints using solvent cement as per manufacturer's instruction, including reducer, socket, bends, TEE etc and laid in wall / floor for connecting bottle traps complete all as specified and directed by Engineer in Charge.

S&F toilet paper holder with flat recessed type stainless steel complete all as specified and directed by Engineer in Charge.

S&F Stainless steel plate rack made out of 1 mm thick stainless steel sheet of size 900x750x250mm complete all as specified and directed by Engineer in Charge.

S&F Brass chromium plated shower roses 125mm size with swivel joint any size fixing in repairs all as directed and specified.

S&F 450mm long PVC connection of approved quality with brass check nuts at both ends for 15mm bore pipe complete all as specified and directed.

S&F Bib tap cast copper alloy chromium plated, fancy type long body, with capstain head handle screwed down screwed for iron pipe and fixed fo 15mm bore pipe after taking down of old brass bib tap complete all as specified.

S&F Rotational moulded polythene water storage tanks, double layered (Cylindrical vertical with closed top) of capacity 500 ltrs, hoisted and fixed in position as in repair and taking down old one complete all as specified.

S&F Ball brass valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed to dia of pipe 20mm as in repairs, complete all as specified and directed.

M&L 20mm bore, gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete.

M&L for cast iron multifloor trap / nahni trap 100 mm dia and 450mm long including jointing with solvent cement fixed in repair complete all as specified and directed by Engineer in Charge.

Cast Iron gully traps,Centrifugal type 150 x 150mm size , square or roundmouthed, type 'P' or 'S' including CI grating fixed in repair complete all as specified abd directed.

Supply and fixing in repairs MS powder coated peg set of Six complete.

S&F in repairs stainless steel soap dish approx size 100x80mm fixed to walls of approved make complete all as specified.

S&F in repairs stainless steel grating with anti-foul self closing cockroach trap of 100 mm dia for floor/nahni traps complete all as specified.

S&F cast iron sand cast soil waste & vent pipe in any length with or without ears with cement joints fixed to walls 100 mm bore including stack clamps, nut bolts etc. and making necessary connections, fixed in repairs complete all as specified and directed by Engineer in Charge.

S&F cast iron sand cast soil waste & vent pipe in any length with or without ears with cement joints fixed to walls 75mm bore in and including stack clamps, nut bolts etc. and making necessary connections, fixed in repairs complete all as specified and directed by Engineer in Charge..

S&F 100mm bore cast iron sand cast soil waste & vent pipe in any length with or without ears with cement joints laid in trenches or in floors complete.

S&F 75mm bore cast iron sand cast soil waste & vent pipe in any length with or without ears with cement joints laid in trenches or in floors complete.

S&F CI bend (any radius) of 100 mm bore in repair.

S&F CI bend (any radius) of 75 mm bore in repair.

S&F CI bend (any radius) with oval access door of 75 mm bore in repair.

S&F CI cowl 100 mm dia.

Taking down eaves, gutters and rain water pipes (any sizes or pattern) incl all fitting incl cleaning for refixing or removing to store yard.

150mm dia PVC(SWR) rain water pipes single socketed in any length with rubber ring joints fixed to walls with and including holder bat clamps made out of 40mm by 3mm FI and 12mm dia round iron stays and making good the disturbed portion in CM 1:3 to match with surrounding area, complete all as specified and directed

PVC(SWR) bends for 150mm dia rain water pipes with rubber ring joints complete all as specified and directed

S&F 6mm thick looking mirror fixed to wall with stainless steel plugs/connecter/spacers/screws etc. chrome finish with wooden beading french polished, etc.complete fixed in position all as specified and directed.

Dismantling wooden boarding of any description, fixed in any position with nails as in shelves of cup board and pelmets of any description complete all as specified and directed by Engineer-in-Charge.

S&F 18 mm thick with min density 600 Kg/cum LEAD FREE PVC Celuka ply of both side plain white colour fixed with screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed. Make : Rajshri Plastiwood /Century ply/National plywood industries.

S&F 18 mm thick with min density 600 Kg/cum LEAD FREE PVC Celuka ply of single side rigid laminate of approved colour and other side plain white colour fixed with SS screws and solvent cement/ adhesive to make kitchen cabinet shutters complete as per manufacturer’s specifications complete all as specified and directed. Make : Rajshri Plastiwood /Century ply/National plywood industries.

S&F 12 mm thick with min density 600 Kg/cum LEAD FREE PVC Celuka ply fixed with SS screws and solvent cement/ adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per manufacturer’s specifications complete all as specified and directed. Make : Rajshri Plastiwood /Century ply/National plywood industries.

S&F 18 mm thick LEAD FREE PVC Celuka ply as in frames of size 75X40mm of both side plain of approved color other than white colour fixed with screws, solvent cement/ adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed. Make : Rajshri Plastiwood /Century ply/National plywood industries

S&F auto closing hinges 35 mm of 0 crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position all as specified. Make : KAFF/Hettich/Kesi/Hetzon

S&F Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs, Make : KAFF/Hettich/Kesi/Hetzon

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150mm long matt finished complete fixed in position all as specified. Make : Harrison (Jasmine)/Adity/Dorset/Sterling

S&F Piano/continuous hinge of size 19 mm stainless steel complete all as specified.

S&F ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions all as specified. Make : KAFF/Hettich/Kesi/Hetzon

S&F Stainless Steel 304 grade wire Basket (avg. wait 2.5 to 4 Kg. per basket) of pull out type like plain/cup&saucer/bottle/multi purpose/2-3 shelf baskets etc. for kitchens of required size complete fixed in position all as specified. Make : Hettitch/Godrej/Kaff/Harrison

S&F Stainless Steel 304 grade Basket Cutlery of size 370X485mm premium quality complete fixed in position all as specified. Make : Hettitch/Godrej/Kaff/Harrison

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engr-in-charge

S&F mild steel work in tubular trusses vertical posts, purlings rafters including special shaped washer etc. complete using ERW or induction butt welded tubes complete all as specified and directed.

Dismantling of asbetos/fibre cement corrugated/semi corrugated sheet in roof covering including ‘J’ or ‘L’hooks complete all as specified and directed by Engr-in-charge

S&F pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick as in covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Mild steel framed work of Fe-290 (Gde E-165) quality as in Doors or gates made of angle and other sections with gusset plates rails braces etc. Complete including drilling and welding for fixing of steel sheeting or other covering of doors, gates etc to be prepared for hanging or sliding with and including drilling and welding for fixing of steel sheeting or other covering of doors gates etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting( Exclusive of steel sheeting or other covering running rails and guides) and handing also fastening and fixing, complete all as specified and directed by Engineer-in-Charge.

Material and labour for providing and fixing stainless steel (grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessaries & stainless steel dash fasterners, stainless steel bolts etc., of required size, on teh top of floor or the side of waist slab with suitable arrangement complete all specified and directed by Engineer-in-Charge.

Taking down carefully existing points wiring on surface conduit/ concealed conduit for light/ fan/socket /power/ bell from wall & roof along with fitting and fixtures such as switches, sockets, ceiling roses, batten holders, unserviceable light fittings, piece of wires,gutties, conduit, wooden boards etc and making good the disturbed portion of all floor, ceiling etc all as specified and directed.

M & L for point wiring with 1.5 sqmm PVC insulated and unsheathed FRLSH(FLAME RETARDANT LOW SMOKE AND HALOGEN) single core multi-stranded copper conductor for one light/fan and including PVC rigid concealed conduit medium grade 19/20 mm dia to be terminated in pressed steel terminal boxes with top cover plate including 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper earth continuity conductor controlled by one switch and/or one regulator including repairing the surfaces in CM 1:3 and finishing the surface as per existing treatment required for fitting of flush and junction boxes all as specified and directed for One light/fan point controlled by one switch 6 amp one way (Switches and regulators shall be measured and paid for separately.) ( Wiring shall be done as per colour code in IS for phase, neutral and earth) (In case of Modular: Modular cover plate and metal flush boxes incl in Point wiring) NOTE:-1.The contractor must produce certificate of FRLSH wire as well as on site testing of FRLSH wire. 2.Make of The modular cover plate must be same make of switch/socket.

All as per item no 120 above but point wiring with 2.5 sqmm single core multi stranded copper conductor PVC insulated & unsheathed cable 1100 volt grade and 1.5 sqmm PVC insulated and unsheathed cable 1100 volt grade with multi stranded copper conductor for earth wire for 15/16 amp multi purpose socket combination point on independent board.

All as per item no 120 above above herein before but one 5Amp socket point on same board but with other switches complete all as specified and directed.

All as per item no 120 above herein before but one 5Amp socket point on independent board but with other switches complete all as specified and directed.

M&L modular switch 1 way 6 A, 1 module

M&L modular socket, 6A-2/3 pin combined, 2 module.

M&L modular switch 16 Amps, 2 module with indicator.

M&L modular socket 16 Amps, 6 pin, 2 module

S & F fan regulator modular type 2 module complete all as specified.

S&F ceiling rose 65x17mm three terminals

S& F Modular Bell switch 1 way, 6 Amps, 1 module complete all as specified.

Suppy and fix bell ding dong type AC 230 volts complete all as specified and directed.

S&F Lamp holder ,PVC/polycarbonate type with back plate suitable for batten fitting.

S&F LED bulb 9 watt all as directed by Enineer-in-charge

Supply and fix in replacement of old unsv building light ,25 W IP 66 LED security light for building luminaire comprising of die cast aluminium housing with weather proof gasket for lamp & driver compartment with system wattage of 25 W . The LED must be of minimum 100 lumen/watt CCT 6500K .The driver must be power factor > 0.95 with short circuit protection , open circuit protection , reverse polarity protection , high voltage protection. the luminaire must have secondary optics with perfectly matched lens for better light control with GI bracket of suitable size and clamps with fixing accessories connection with PVC insulated three core flexible copper conductor cable 0.75X3 Sqmm with proper clamps .complete all as specified and directed by Engr in charge.

S&F incl taking down 20 watt wall mounted, new generation LED batten fitting 4 feet with polycarbonate diffuser andextruded thermoplastic body > 90 lumen/watt having correleted color temperature(CCT) of Emitting light 6500/3000 K with CRI of LED >90 . including all fixing accessories & connecting up with PVC insulated twin core flexible copper conductor cable of suitable size complete all as specified and directed by Engr in Charge.

S&F incl taking down 10 watt wall mounted, new generation LED batten fitting 2 feet with polycarbonate diffuser andextruded thermoplastic body > 90 lumen/watt having correleted color temperature(CCT) of Emitting light 6500/3000 K with CRI of LED >90 . including all fixing accessories & connecting up with PVC insulated twin core flexible copper conductor cable of suitable size complete all as specified and directed by Engr in Charge.

Supply and fixing earth metal plug and socket single pole and neutral with a two pin and earth plug and socket alongwith one single pole MCB of 20 Amp concealed in wall all as directed by Enineer-in-chargr.

M & L for replacement of Sub main wiring with two single core 6.0 Sqmm PVC insulated and unsheathed FRLSH ,stranded copper conductor cable drawn through PVC concealed conduit 25 mm dia including 6.0 Sqmm PVC insulated unsheathed FRLSH stranded copper conductor cable as earth wire all as specified and directed by Engineer-in-charge. Note 1:- 2(two) Runs of 6.00 Sqmm Copper conductor cable, 1 Run of PVC conduit & 1 Run of 6.00 Sqm Copper conductor Earth wire shall be measured as one unit) Note 2 :(i) Rate quoted for this items shall be inclusive of the cost of (i) Rigid non-metallic PVC conduit of 25 mm dia with tees, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. (ii) Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to match the existing surfaces and cutting not exc. 10 cm girth . (iii) Including taking out/down existing unserviceable sub main wiring.

M & L for Sub main wiring with two single core 4.0 Sqmm PVC insulated and unsheathed FRLSH ,stranded copper conductor cable drawn through PVC concealed conduit 25 mm dia including 4 Sqmm PVC insulated unsheathed FRLSH stranded copper conductor cable as earth wire all as specified and directed by Engineer-in-charge. Note 1:- 2 Runs of 4.00 Sqmm Copper conductor cable, 1 Run of PVC conduit & 1 Run of 4.00 Sqm Copper conductor Earth wire shall be measured as one unit) Note2 : Rate quoted for this items shall be inclusive of the cost of (i) Rigid non-metallic PVC conduit of 25 mm dia with tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. (ii) Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to match the existing surfaces, cutting not exc. 10 cm girth . (iii) Taking out/down existing unserviceable sub main wiring.

supply and fixing exhaust fan 300mm,metalic body single phase ac 220 V silent type with 4 no of blades compelete all as specified and as directed.

supply and fixing Exhaust fan pvc body 250mm,single phase ac 220 Vcompelete all as specified and as directed.

Supply,installation and testing of minimum 5 star rated electric water heater (Geyser) metal body storage type of 25ltrs capacity of Steel tank including 04 nos anchor fastening for mounting geyser and other nut,bolt and washers with 3 core flexible wire of size 2.5 Sqmm from Geysere to metal plug and socket including 02 Nos of PVC Pipes all as directed .

M&L in replacement of old/damaged earthing complete with galvanized steel earth plate electrode 600mmx600mmx6.3 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level,the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15cm on all side and including connected toand including galvanized earth lead wire 4.0 mm dia upto 7.5 mtrs long by means of nuts and bolts, check nuts and washers of GI and connected to earhing test point and earth dolly all as shown in electrical plate No 3 of MES SSR part I and testing on completion including necessary excavation and earth work in any type of soil,PCC(1:3:6)type C1 chamber,pre-cast RCC slab 50mm thic in cement concrete (1:2:4),type B1,reinforced with welded steel wire fabric or XPM,(weight not less than 4 Kg per Sqm) with cast iron frame,funnel with watering pipe 20mm dia medium grade,wire mesh and lugs,GI protection pipe,15mm dia,light grade,7.5 mtr long for protection of earth lead upto test point etc all as specified and as directed.

Supply and fix incl taking down new generation energy saving 9/10 watt LED bulk head (porch light fitting) made of plasitic housing with opal diffuser With IP 65. having correleted color temperature(CCR) of Emmiting light 6500/3000 K with CRI of LED >90. connection with PVC insulated twin core flexible copper conductor cable of suitable size.complete all as specified and directed by Engr in Charge.

Supply and fix incl taking down Led Stellar Square/round SURFACE Mounted Asthetically designed energy saving LED LIGHT for indoor application of capacity 10 watt having correleted color temperature(CCR) of Emitting light 6500 OR 3000 K(According to requirement) with CRI of LED >90.complete with all electrical connection with PVC insulated twin core flexible copper conductor cable 0.75X2 Sqmm with proper clamps.complete all as specified and directed by Engr in charge.

Supply and fix incl taking down antique look decoretive surface mounted classic living room wall light with base cap B22/E27 body made with METAL and glossy GLASS having fitting capacity upto 20 watt. connection with twin core twisted flexible copper conductor cable .75X2 Sqmm with proper clamps complete all as specified and directed by Engr in Charge.

Supply and fix incl taking down outdoor decorative LED Post top lantern with spun aluminium die cast Housing cum heat sink PMMA diffuser in IP66 with base cap B22/E27 fitted LED bulb of 20watt. complete all as specified and directed by Engr in Charge.

Preparation of surfaces and applying 02 coats of exterior emulsion paint (light shade) by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer over and including 1.5 to 2.5mm thick wall care putty complete all as specified and directed.

M&L hardcore of broken bricks of gauge n exc 63mm, deposited, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface complete.

M&L for rubber moulded coloured chequered tiles 20cm x 20cm x 25mm thcik with grey cement and pigment, set jointed and pointed in neat cement slurry as in floor complete all as specified and directed.

M&L cement concrete type B1 1:2:4 (20 mm graded stone aggregate) in roof kerbs, paddings or mud stops rounded or chamfered, coping etc complete all as specified and directed.

Excavating in post holes in soft/ loose soil (or similar holes) each n exc. 0.5 cum , getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

M&L for preparation of surfaces of steel and applying two coat synthetic enamel paint over a coat of red oxide primer complete, all as speciifed and directed.

S&F pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick as in covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Reinforced concrete pipes of 150mm dia, class NP3, laid and jointed complete with collars and jointed complete in cement mortar (1:1) complete all as specified and directed by Engr-in-charge.

Excavation in trenches in soft/loose soil not exceeding 1.50 Mtr wide and not exceeding 1.50 Mtr in depth and getting out in soft/loose soil complete all as specified and directed Engineer-in-Charge

M&L for concrete bed type D-2 1:4:8 using 40mm stone agg) to drain pipes of any sizea and of any dia complete.

Returning and filling incl spreading, levelling, water and well ramming in layers not exceeding 25cm thick complete all as specified and directed Engr-in-charge

Removal of excavated material n. exc 50 M and depositing where directed at a level not exc 1.5 M above the starting point

Buttar Construction Co. (BID ID -3101461)

DELTA CONSTRUCTION CO (BID ID -3108537)

AR CONSTRUCTIONS (BID ID -3108635)

Arneja Builders (BID ID -3097890)