Construction of Proposed TNPCBs R and D Building for Tamil Nadu Pollution Control Board adjacent to existing TNPCB Corporate office at Guindy in Chennai city

Earth work excavation in all soils (including refilling) a) 0 to 2 mt.

b) 2 m to 3m

c) 3m to 4 m

d) 4 m to 5 m

e) 5 m to 6 m

Earth work excavation for Open foundation (excluding refilling) a) 0 to 2 mt.

Shoring with 'Z' section MS sheet piles side by side in all kinds of soil mechanically or manually as per approved drawing with contractor’s own arrangement Note: Payment will be made as per actual driven length of pile.

Earth work excavation for foundation in all soils and sub soils to the required depth as may be directed except in hard rock requiring blasting, inclusive of shoring, strutting and bailing out water wherever necessary, (Excluding refilling the sides of foundation) (Excluding Refilling)

Providing and fixing rock anchors by drilling holes of required diameter and depth in hard rock using approved rotary or percussion drilling equipment.

Filling with Excavated Earth

Supplying and filling with red earth of approved best quality for court portion including cost and conveyance of red earth of approved quality, labour charges for watering with soft potable water

Getting out and disposal of excavated excess earth, lead and lift as directed by Engineer-in-charge in All kinds of soil.

Dewatering with pumps of adequate HP including draining

Providing pre-constructional Antitermite treatment including cost of chemicals labour as per standard specifications

Plain cement concrete 1:5:10 for Foundation & Basement

Supplying and filling in foundation and basement with crushed stone sand in layers of 150 mm thickness

Providing and laying in position, Standardised Concrete Mix M-35 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for the all RCC items of works a. Below Ground level upto 4.5m

b. In Ground Floor

c. In First Floor

d. In Second Floor

e. In Third floor

f. In Fourth floor

g. In Fifth floor

Providing and laying in position, Standardised Concrete Mix M-40 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for the all RCC items of works a. In Foundation and basement

b. In Ground Floor

c. In First Floor

d. In Second Floor

e. In Third floor

f. In Fourth floor

g. In Fifth floor

Formwork using M.S.Sheet a) For Column footings, plinth beam, Grade beam, aftbeam, Raft slab etc.,

b) Plain surfaces such as Roof slab, floorslab, Beams, lintels, lofts,sill slab,staircase,portico slab and other similar works

c) For Square and rectangular columns and small quantities

d) Vertical wall

Providing additional Strutting to centering of R.C.C slab and beams of all surfaces or any other form works required at site during execution of work for every additional 1 1 RMT height

Supplying, Fabrication and placing of Mild steel grills Fe550D (Corrosion resistant reinforcement) of all diameters for reinforcements for all floors

Supplying & fixing PVC rungs at required spacing as per direction of Engineer-in-charge.

Supplying and fixing Mild Steel grills as per the design approved to verandah enclosure or gate

Supply,fabricating and errection of steel truss (weight basis) in suitable Tee angle, rafter, purlins, cross, 'I' angles, supporting angle, including cost of bolt and nut

Post Tensioning Work: Design and execution of post tensioning work, including decoiling, the strands, cutting to the required lengths, supplying, laying of HT strands sheathing (GI corrugated ducts 0.3mm thick) jointing with couplers a) Basement Roof

b) Ground Floor Roof

c) First Floor Roof

d) Second Floor Roof

e) Third Floor Roof

f) Fourth Floor Roof

Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry with 100 mm thick (As per manufacturer standard) with Grade-I AAC blocks of density 551 to 650 kg/ cum a) Ground Floor

b) First Floor

c) Second Floor

d) Third Floor

e) Fourth Floor

Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry with 200 mm thick (As per manufacturer standard) with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) a) Ground Floor

b) First Floor

c) Second Floor

d) Third Floor

e) Fourth Floor

f) Terrace Floor

Providing and laying factory made Precast concrete solid block work of 200 mm thickness of grade M10 from approved manufacturer in foundation, plinth and in in superstructure above plinth level up to floor V level in cement mortar 1:6 (1 cement : 6 coarse sand) a) Ground Floor

b) First Floor

c) Second Floor

d) Third Floor

e) Fourth Floor

Special ceiling plastering in cement mortar 1:3, 10 mm thick

Plastering in C.M. 1:4, 12 mm thick

Plastering with CM 1:3, with 20 mm thick mixed with water proofing compound (CICO) at the rate of 2 kg / 10 sq.m

BASEMENT & RC WALLS WATERPROOFING Supplying and installing waterproofing treatment for Raft Slab by using fully bonded HDPE sheet membrane on the Raft slab & RCC Wall.

Suppllying and applying waterproofing works including the following, 1. Surface Preparation: Providing and cleaning the surface to make it free from all the loose mortar, dust, 2. Applying two or more coats of water Proofing Brush Bond over the slab surface and allowing it to dry and ensuring the smooth finish. 3. Providing & laying to protective cement plaster in ratio 1:4

TERRACE WATERPROOFING (Floor area will be measured) Suppllying and applying waterproofing works including the following, 1. Surface Preparation: Providing and cleaning the surface to make it free from all the loose mortar, dust, and other contaminants and protrusions which may damage the membrane, 2. Applying two or more coats of water Proofing Brush Bond over the slab surface and allowing it to dry and ensuring the smooth finish. 3. Providing & laying to required slope CEMENT CONCRETE SCREED of mix 1:1.5:3

Plain cement concrete 1:8:16 (One of cement, eight of sand and sixteen of broken brick jelly) for foundation and other similar works using 20mm gauge broken Brick Jelly

Supply and laying of superior variety Concrete Designer tiles for flooring in CM 1:3

Supplying and fixing of Stain free Nano polish Vitrified Tiles of size (600x600x8mm) for flooring C.M 1:3, 20mm thick

Supplying and fixing of colour Granite slab (LEATHER FINISHED with machine cut edges) of required sizes of 20 mm thick for steps and landing flooring over cement plastering in CM 1:3, 20mm thick with Grout (Tile joint filler) ( Tan Brown)

Providing round nosing to the edges of Granite slab of 18 to 20 mm thick

Extra for making grooves in treads

Supplying and fixing of Granite slabs (Super fine polished with Machine cut edges) of size 4'x2' and above 18mm to 20 mm thick for flooring

Supplying and fixing of Granite Tiles (superfine polished with machine cut edges) of required sizes of 10 mm thick for wall cladding

Supplying and fixing of colour Anti Skid Vitrified Tiles of size 600 x 600mmx10mm for flooring and other similar works

Supplying and fixing of Colour glazed tiles using Grout (Tile Joint Filler), C.M 1:2, 10mm thick

Supplying and fixing of colour Vitrified Tiles of different sizes for flooring and other similar works in cement mortar 1:3, 20mm thick with grout (Tile joint filler) a) 1200x1200mm (Glazed)

b) 1200 x 1800mm (Glazed)

c) 1200 x 2400mm (Polished)

Providing and fixing 600x600x10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid

Finishing the top of Terrace floor with one course of solar reflective water proof, heat proof and cool roof ceramic tiles of size 300mmx300mmx8mm thick of approved quality

Painting the false ceilling / New walls with one coats of 1st class ready mixed plastic emulsion paint of best approved quality colour and shade including a priming coat

Finishing walls with 1st quality internal emulsion having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour

Providing & Applying high quality acrylic modified resin based texture as per the architectural Pattern with anti algae and UV resistance properties to be applied as intermediate finish in desired pattern

Finishing external walls with premium acrylic emulsion paint of exterior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and manufacture, including one coat of primer

Providing and applying low-VOC synthetic enamel paint on all MS works including thorough surface preparation by removing rust, oil, dust, and welding scales

RAILING WORKS Providing, fabricating, and fixing Stainless Steel (SS) handrail system with toughened glass panels, including all necessary accessories and supports, complete in all respects.

Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing

Providing 40 x 5mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter

Teak wood Wrought & Put up a) T.W. over 2 m & below 3 m

b) T.W. below 2 m length.

Supplying and fixing of Single leaf Solid core flush door shutters using boiled water resistance (BWR) teak wood ply as per IS 303-1989 b) Door size 900mm x 2400mm (single Leaf)

Supplying and fixing of Double leaf Solid core flush door shutters using boiled water resistance (BWR) teak wood ply as per IS 303-1989 c) 1800 x 2400mm

Providing and fixing in position Engineered Wooden Door as per IS 2202 (Part 2), including door frame of size 6" x 4", and door shutter of 35 mm suitable thickness

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/clerestory windows &desertory other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheathusk) Frame size 45 x 85 mm

Providing and fixing factory made single extruded WPC (WoodPolymer Composite) solid plain flush door shutter of requiredsize comprising of virgin polymer of K value 58-60 (SuspensionGrade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) 30mm thick shutters

Sliding WPC Doors : Providing and fixing factory made single extruded WPC (WoodPolymer Composite) solid plain flush door shutter 30mm thick shutters

Providing and fixing bright finished brass handles with screws (Basic price not less than Rs. 3500/-) etc. complete in all floors

Providing and fixing bright finished brass handles with screws (Basic price not less than Rs. 1300/-) etc. complete in all floors

Providing and fixing stainless steel fancy handle of approved make fixed with SS screws (Basic price not less than Rs. 750/-) etc.

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. (Basic price not less than Rs. 1500/-)

Providing and fixing bright finished brass 100 mm double door mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. (Basic price not less than Rs. 1500/-)

Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete as per samples approved by EIC complete in all floors ( for Main Doors) (Basic price not less than Rs. 250/-)

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body), with necessary accessories and screws

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. a) 250x10 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc a) 250x10 mm

Providing and fixing magnetic catcher of approved quality in doors, including fixing with necessary screws etc. complete

Providing wooden ( Melamine Door ) Polish for new wood by removing by blade scrapping the exisiting dirt from the wooden surface using sand paper with M50 and repeat M80 paper to get a smooth surface leave

Painting the new wood work with two coats of approved first class synthetic enamel ready mixed paint in addition to one coat of primer of approved quality and shade,

Providing and fixing fully glazed 12mm thick Toughened glass door comprising of two leaf glass shutters and height 2400mm fully glazed with necessary handles, etching,pivot arrangements complete etc.

Supplying and fixing of push and pull type steel Rolling shutters (Gear operated) of best approved quality

Service Windows Providing and fixing colour anodized aluminium service windows fabricated from approved quality extruded aluminium profiles conforming to IS:733 and IS:1285, LW1 (1000x2250mm)

LW3 (750x2250mm)

LW4 (3000x2900mm)

LW6 (1200x2400mm)

LW7 (3000x4400mm)

LW9 (2500x2500mm)

Fixed Aluminium Glazing Providing and fixing fixed aluminium glazing fabricated from approved quality extruded aluminium profiles conforming to IS:733 and IS:1285, finished with pure polyester powder coating of not less than 50–60 microns in approved colour. W1 (1000x2250mm)

Ventillators Providing and fixing aluminium ventilators fabricated from approved quality extruded aluminium profiles conforming to IS:733 and IS:1285, finished with pure polyester powder coating of not less than 50–60 microns in approved colour V1 (600x600mm)

Providing and fixing 80mm thk. Glass bricks of approved make, size and type in glass block adhesive

ROAD WORKS Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations

Crusher Run Macadam Sub Base/Base Course Providing crushed stone aggregate, depositing on a prepared surface by hauling vehicles, spreading and mixing with a motor grader, watering and compacting For 53 mm maximum size

Dry lean cement concrete Sub-base Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383

Cement Concrete Pavement Construction of un-reinforced, dowel jointed, plain cement concrete pavement M-40 grade concrete over a prepared sub base with cement, coarse and fine aggregate conforming to IS 383,

Supplying and laying of 60mm thick factory made cement concrete paver block of M-30 grade made by block making machine

Supplying and fixing of 20mm thick bituminous expansion joint filler pad of approved quality and make

Providing Silicon Sealant expansion joint treatment for the vertical wall, roof top sides using app sealant material

Drilling of Borewells anywhere in Tamilnadu including transportation from one place to another with in Tamilnadu in alluvial soil sedimentary strata of clay and sand stone shale pebbles boulders etc Upto 60 m Depth ending below ground level

From 60 m upto 90 m Depth ending from ground level

From 90 m upto 120 m Depth ending from ground level

Supply and erection of following dia of PVC casing pipes (6Kg/cm2) as per IS 12818/2010 of approved quality for bore wells a) 150mm dia of PVC casing pipes (6Kg/cm2) (Mediun depth)

Supply and delivery of 150mm dia of Ribbed screen PVC casing pipes (6Kg/cm2) without excise duty as per IS 12818/2010 of approved quality for bore wells

Labour charges for inserting of Following PVC Casing pipes assembly (With slots or without slots) in the drilled hole a) 150mm dia casing pipes assembly

Supply and fixing of 160mm dia PVC end cap of approved make as per IS 10124/1982 Part-II for borewell top cover of 6.1mm thick with inner thread

Charges for developing the bore well with air compressor of 600 CFM capacity (Minimun 8 Hours)

Supplying, laying, fixing and jointing the following dia HDPE pipes of approved make ISI suitable for borewell including the cost of suitable HDPE /GI specials/GM specials 32mm dia HDPE hose

Supply and delivery of required dia Nylon rope of superior quality for submersible pump1 Set in borewell

Supplying and fixing of following dia Gun Metal Gate Valve as per IS BS 5154 and related IS Specifications c. 32mm Gate valve

Supplying and delivery of following dia MS clamp 1 Sets as per IS 1239/part II for erection of submersible pump1 Set in wells b. 40mm dia M.S clamp 1 Set

Supply and delivery of clear water vertical wet type (Three Phase) submersible pump1 Set suitable for 150mm dia borewell conforming to IS 8034/2002 without panel board Duty:150 LPM x 125m

Labour charges for the erection of submersible pump1 Set in borewell /openwell including fixing and jointing submersible cable with proper clamps upto the starter to required depth Upto 5 HP

Supply and delivery of direct online starter single phase panel board with two level guard and auto start confirming to IS13947, IEC60947-1 and as amended thereafter with suitable KW rating for operation in AC/single Phase/50HZ(± 5%) and 230 V(±10%)

Supply and laying of PVC insulated and sheathed follwing core and sq.mm flat type copper cable confirming to IS 694/1990, cable for submersible motor etc a) 3 core 4 Sq.mm flat type copper cable

Supplying of following dia PVC pipes as per ASTM -D - 1785 of schedule 40 including conveyance charges etc Below G.L a) 32 mm dia PVC ASTM-D pipes Schedule- 40

INTERIORS AND FURNISHINGS Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) 12.5 mm thick fully Perforated Gypsum Board

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) With 8 mm thick fully perforated calcium silicate board

Providing & fixing 12mm thick clear toughened glass fixed partitions. The rate is inclusive of providing of 3M film as per approved pattern/ Design on the glass, cost of materials and labour charges etc.

Providing and fixing in position full Partition work as per drawing ,in frame work at 2’x2’ grind (horizontally and vertically)

Providing and fixing single leaf 12mm Toughened Glass door mounted on approved make fittings, Springs and handles

Supply and installation of Toilet Partition System comprising of 16mm thick particle board panels, laminated both sides with Melawood or Formica (of approved colour)

Manufacture, supply, and installation of modular office workstations, tables, and storage units made from high-quality materials as per approved design and drawings. Workstations shall be fabricated using 25 mm thick 2800x1200mm

Chairs Supplying of Ergonomically designed low back executive revolving chair with high density moulded foam seat, upholstered

Supplying of Ergonomically designed medium back visitor chair with moulded foam seat and back upholstered

Supplying of Ergonomically designed high back executive revolving chair with moulded foam seat and back, upholstered

Supplying of Ergonomically designed medium back chair with high density foam seat and back upholstered with leatherite, soft touch leatherite cushion arms and having cantilivered chromium plated frame.

Providing and fixing storage units of full/ low height as per requirements. They shall consist of 18mm thick.

Providing and fixing tables of various sizes on site/factory as per TNPCB requirements. All tables shall have tops and legs fabricated from 25 mm thick prelaminated boards Waiting Area - Reception Table (2400x600mm)

EE Room - Table (2000x1000mm)

JCEE Room - Table (2000x1000mm)

Meeting Room - Table (3000x1800mm)

Meeting Room - Table (2700x600mm)

Solids Room - Table for equipments (7850x600mm)

Solids Room - Central Table (1000x1500mm)

Solids Room - Corner curverd table (2700x600mm)

Physical Analysis - Table for equipments (1900x600mm)

Physical Analysis - Centre table (1900x600mm)

Physical Analysis - Corner table (2600x600mm)

Sample preparation room - Working Table (2000x600mm)

Sample receiving room - Table (1500x600mm)

Head scientist room - Table (1000x2000mm)

Water chemical analysis lab - BOD Table (1500x3600mm)

Water chemical analysis lab - COD Table (1500x3600mm)

Water chemical analysis lab - Hardness & Chloride table (1500x3600mm)

Water chemical analysis lab - TKN & AMMONICAL (1500x3600mm)

Water chemical analysis lab - TRC & DO (1500x3600mm)

Water chemical analysis lab - OIL INCREASE TABLE (1500x3600mm)

Water chemical analysis lab - FLUORIDE & SULPHATE, NITRATE ETC., (7200x1500mm)

Meeting Room - Table (1500x2800mm)

Equipment room for metal digestion - Working Table (4400x600mm)

Equipment room for Instrumentation room - Working table (2870x600mm)

Instrumentation room - Working table (4870x600mm)

Equipment room for heavy metal room - Working table (3630x600mm)

Heavy metal room - Working table (4730x600mm)

Equipment for trace metal room - Working table (2470x600mm)

Trace metal room - Working table (4720x600mm)

Direct Mercury Analysis - Working table (7200x600mm)

Total Organic carbon - Working table (7200x600mm)

Trace organics room - Working table (7200x600mm)

Air Lab - Tables (1500x3600mm)

Conference hall - Table (16230x600mm)

Conference hall - Projector with table (8320x3150mm)

Reception cum waiting - Reception table (1400x600mm)

Library - Circular table (1200mm dia)

Supplying and placing of Ergonomically designed high back Senior executive revolving chair with foam seat and back upholstered

Providing, fabricating, and installing a stepped deck with necessary support systems,

Supply, fabrication, and installation of counters made of plywood,

Supply and fixing of Fabric blackout blinds using in 0.4mm thick and of required sizes,

Brick cladding work (machine cut edges) with 20mm thick bricks (sample as approved by the architect) for exterior walls etc. (Basic price of cladding brick not less than Rs. 1600 per Sqm)

Supply, fabrication, and installation of acrylic letters and signage for logo and name boards, including backlit LED illumination

Supplying and laying of Jet black varieties Granite slabs (super fine polished with machine cut edges) of size 4'-0"x 2'-0" of 18 to 20 mm thick, for kitchen platform slabs pointing the joints with Grout (Tile joint filler) (Basic price of granite not less than Rs. 1300 per Sqm),

Miscellaneous Items Dismantling the damaged brick works in cement mortar in all floors without affecting the adjacent structures 3m high

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

Plastering in CM 1:5, 12mm thick for border finish in all floors a. 150 mm wide

b. 75 mm wide

c. 50 mm wide

Providing and laying cement concrete in string or lacing courses, parapets, coping, plain window sills etc., up to all floor levels

Providing and fixing precast cement concrete in string or lacing courses, parapets, coping, plain window sills etc., up to all floor levels

Providing and applying 12 mm thick (average) premixed formulated one coat gypsum light weight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976,

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Providing and fixing of Kota stone slabs 20 mm thick in risers of flooring, steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3

Providing and fixing parallel threaded couplers conforming to IS code on “Reinforcement Couplers for Mechanical Splices of Bars for Concrete Reinforcement Coupler for 16 mm diameter reinforcement bar

Coupler for 20 mm diameter reinforcement bar

Coupler for 25 mm diameter reinforcement bar

Coupler for 32 mm diameter reinforcement bar

Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete

Cutting holes in R.C.C beams / slabs with core cutter machine. upto 150mm dia

above 150mm and upto 300mm dia

above 300mm dia

Providing and laying machine cut, mirror polished, Imported Marble stone flooring laid in required pattern as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (Basic Price not less than Rs 7000/ Sqm)

Providing and fixing machine cut, mirror/ eggshell polished, Imported Marble stone work for dado, skirting, treads & risers of steps etc., (Basic Price not less than Rs 7000/ Sqm)

Extra for pre finished nosing to treads of steps, skirting of marble stone

Providing, installation, Testing & Commissioning of Bi-Parting Automatic Sliding Door Operator complete with a pair of bi-parting doors and two fixed side screens. (Basic Price not less than Rs 7000/ Sqm)

Providing and fixing STAINLESS STEEL BRASS ETCHING name plates

Providing and fixing BLUE ACRYLIC VINYL name plates for common areas

Providing and installation on FAÇADE SIGNAGE as per archictectural design with necessary backlighting

LANDSCAPE WORKS Plumeria Ulta (Temple Tree) – Supplying and planting with organic mix, proper spacing, and initial watering for plant/tree establishment (Height: 2.5 m).

Murraya Paniculata (Orange Jasmine) – Supplying and planting with organic mix, proper spacing, and initial watering for plant/tree establishment (Height: 2.5 m).

Duranta Goldii (Golden Duranta) – Supplying and planting for hedge/ground cover with organic mix, spacing, and initial watering for establishment (Height: 0.7 m).

Ficus Reginald (Weeping Fig) – Supplying and planting with organic mix, proper spacing, and initial watering for plant establishment (Height: 1.5 m).

Concrete Slab Flooring with Grass (Concrete tile size: 0.3 x 0.6 m with Bermuda grass in openings) – Supplying and laying concrete grass paver tiles with soil mix filling and turfing.

Concrete Kerb (0.15 m width, 0.23 m height) – Supplying and laying precast concrete kerb stones including base concrete, alignment, joint filling, and finishing.

Supply,Erection, testing and commissioning of 11KV, 25 KA, 630A, Indoor type Ring Main Gear (RMG HT RING MAIN GEAR comprising of Two Incoming Air Break Load Break Switches and One Outgoing HT Vacuum Circuit Breaker for INDOOR Installation

2) UNITIZED SUBSTATION Erection testing and commissioning of 630kVA Unitized Substation for INDOOR Installation 11KV, 25 KA, 630A, OUTDOOR SINGLE PANEL VACCUM CIRCUIT BREAKER 630kVA ANAN Dry type Transformer with OLTC 1000A 4P MDO 35kA ACB as LT Breaker

Supply laying and jointing of control cables for transformer and RTCC Panel 19C x 2.5Sqmm Cu cable

4C x 2.5Sqmm Cu Cable

2C x 2.5Sqmm Cu cable

HT Cable Supply and laying of HT Cable in the existing trench or cable tray with all necessary supports complete 1 Sets. 3C x 185Sqmm XLPE Al 11kV( E) cable

Heat shrinkable HT Cable Joints Supply erection, testing and commissioning of indoor type HT Cable joints with following specification 3C x 185Sqmm XLPE Al 11kV( E) cable

BUS BAR TRUNKING & RISING MAINS i) Supply Erection testing and commissioning of 800A Aluminium conductor Sandwich Design Rising Main with 40 X 6 (2) External Aluminium Earthing, 3 Plug in Points at every Floor, Spring & Rigid Hangers: Indoor : 50KA - IP 54

ii) Vertical / Horizontal Bend - Provision Cost (i,e Cost of Bus bars will be Calculated over & Above Straight Run Cost)

iii) End cover

iv) 400A Tap Off Box With MCCB (cost includes of MCCB + RHOM) with Dual Source Energy Meter

v) 100A Tap Off Box With MCCB (cost includes of MCCB + RHOM) with Dual Source Energy Meter

vi) 63A Tap Off Box With MCCB (cost includes of MCCB + RHOM) with Energy Meter

vii) Fabrication of structural supports for 400Amps BBT as required comprising of channels, angles, flats grouting, on coat of red oxide and two coats of synthetic paint. Complete 1 Set

6.10) MAIN LT PANEL Supply, erection, testing and commissioning of MV cubicle type suitable for 415V, 3-phase, 4 wire system, compatible to BMS totally enclosed floor mounted type, dust, damp and vermin proof main distribution board with made out of 14 SWG MS sheet RATING : 1000 AMPS

6.20) 250KVAR APFC Panel (Contactor Switching with Harmonic Filter) Supply of MV cubicle type suitable for 415V, 3-phase, 4 wire system, compatible to BMS totally enclosed floor mounted type, dust, damp and vermin proof main distribution board with made out of 14 SWG MS sheet RATING : 400AMPS

6.30) HVAC PANEL Supply, installation, testing and commissioning of MV cubicle type suitable for 415V, 3-phase, 4 wire system, compatible to BMS totally enclosed floor mounted type, dust, damp and vermin proof main distribution board with made out of 14 SWG MS sheet RATING : 250AMPS

6.40) POWER PANEL (PCC) Supply, installation, testing and commissioning of MV cubicle type suitable for 415V, 3-phase, 4 wire system, compatible to BMS totally enclosed floor mounted type, dust, damp and vermin proof main distribution board with made out of 14 SWG MS sheet RATING : 80AMPS

6.50) EXHAUST FAN PANEL Supply, installation, testing and commissioning of MV cubicle type suitable for 415V, 3-phase, 4 wire system, compatible to BMS totally enclosed floor mounted type, dust, damp and vermin proof main distribution board with made out of 14 SWG MS sheet RATING : 125AMPS

6.60) BASEMENT FLOOR PANEL Supply, installation, testing and commissioning of MV cubicle type suitable for 415V, 3-phase, 4 wire system, compatible to BMS totally enclosed floor mounted type, dust, damp and vermin proof main distribution board with made out of 14 SWG MS sheet RATING : 125AMPS

6.70) FLOOR PANEL(TYP) Supply, installation, testing and commissioning of MV cubicle type suitable for 415V, 3-phase, 4 wire system, compatible to BMS totally enclosed floor mounted type, dust, damp and vermin proof main distribution board with made out of 14 SWG MS sheet RATING : 200AMPS

6.80) LT PANEL-1 SITE-02 Supply, installation, testing and commissioning of MV cubicle type suitable for 415V, 3-phase, 4 wire system, compatible to BMS totally enclosed floor mounted type, dust, damp and vermin proof main distribution board with made out of 14 SWG MS sheet RATING : 80AMPS

6.90) LSB SITE-02 Supply, installation, testing and commissioning of MV cubicle type suitable for 415V, 3-phase, 4 wire system, compatible to BMS totally enclosed floor mounted type, dust, damp and vermin proof main distribution board with made out of 14 SWG MS sheet RATING : 100AMPS

6.10) SUB PCC SITE-02 Supply, installation, testing and commissioning of MV cubicle type suitable for 415V, 3-phase, 4 wire system, compatible to BMS totally enclosed floor mounted type, dust, damp and vermin proof main distribution board with made out of 14 SWG MS sheet

6.11) ELECTRIC CAR CHARGING DB Supply, installation, testing and commissioning of MV cubicle type suitable for 415V, 3-phase, 4 wire system, compatible to BMS totally enclosed floor mounted type, dust, damp and vermin proof main distribution board with made out of 14 SWG MS sheet

6.12) ISOLATOR WITH IP55 PROTECTION Supply, installation, testing and commissioning of MV cubicle type suitable for 415V, 3-phase, 4 wire system, compatible to BMS totally enclosed floor mounted type, dust, damp and vermin proof main distribution board with made out of 14 SWG MS sheet 1000 Amps 35kA 4Pole MCCB type isolator for 625kva DG 1 Set

7.10) LIGHT DISTRIBUTION BOARD (LDB) Supply, ercetion, testing and commissioning of 8 way TPN DB with following specifications. INCOMER : 63 AMPS 4 P MCB - 1 No. OUTGOING : 40 AMPS D P 30 MA RCB - 3 Nos. 6 AMPS SP MCB - 24Nos.

7.20) POWER DISTRIBUTION BOARD PDB) i) Supply, erection, testing and commissioning of 8 way TPN DB with following specifications. INCOMER : 63 AMPS 4 P MCB - 1 No. OUTGOING : 40 AMPS D P 100 MA RCBO - 3 Nos. 16/32 AMPS SP MCB - 24Nos.

ii) Supply, erection, testing and commissioning of 8 way TPN DB with following specifications. INCOMER : 63 AMPS 4 P MCB-1 No. OUTGOING : 40 AMPS DP A Type 30MA RCBO-3 Nos. 16/32 AMPS SP MCB- 24Nos.

7.30) UPS DISTRIBUTION BOARD (UPS DB) i) Supply, erection, testing and commissioning of 12 way TPN DB with following specifications. INCOMER : 63 AMPS 4 P MCB -1 No. OUTGOING : 40 AMPS DP A Type 30MA RCBO- 3 Nos. 16/32 AMPS SP MCB -36Nos.

ii) Supply, erection, testing and commissioning of 8 way TPN DB with following specifications. INCOMER : 63 AMPS 4 P MCB-1 No. OUTGOING : 40 AMPS DP A Type 30MA RCBO-3 Nos. 16/32 AMPS SP MCB- 24Nos.

iii) Supply, erection, testing and commissioning of 12 way SPN DB with following specifications. (M.ELDB) INCOMER : 32 AMPS 30mA RCBO - 1 No. OUTGOING : 16/6 AMPS SP MCB-10Nos.

iv) Supply, erection, testing and commissioning of 12 way SPN DB with following specifications. (M.ELDB) INCOMER : 32 AMPS 30mA RCBO -1 No. OUTGOING : 25 AMPS SP MCB - 10Nos.

v) Supply, erection, testing and commissioning of 12 way SPN DB with following specifications.(SUB.ELDB) INCOMER : 25 AMPS DP 30mA RCBO -1 No. OUTGOING : 6 AMPS SP MCB -10Nos.

vi) Supply, erection, testing and commissioning of 8 way SPN DB with following specifications.(SUB.ELDB) INCOMER : 25 AMPS DP 30mA RCBO - 1 No. OUTGOING : 16/6 AMPS SP MCB -6Nos.

7.4) VERTICAL DB Supply, ercetion, testing and commissioning of 8 way Vertical DB with following specifications. INCOMER : 63 AMPS 4P MCB -1 No. OUTGOING : 32 AMPS TP MCB - 8Nos.

CABLES/TERMINATIONS Supply, Laying, connecting and commissioning the following 1.1KV Grade AYFY/YFY/YWY Under Ground cables with necessary clamps screws a) 3.5C x 300Sqmm Al XLPE FRLS LH Cable

b) 3.5C x 240Sqmm Al XLPE FRLS LH Cable

c) 3.5C x 240Sqmm Al XLPE FS Cable

d) 3.5C x 150Sqmm Al XLPE FRLS LH Cable

e) 3.5C x 120Sqmm Al XLPE FRLS LH Cable

f) 3.5C x 95Sqmm Al XLPE FRLS LH Cable

g) 3.5C x 70Sqmm Al XLPE FRLS LH Cable

h) 3.5C x 50Sqmm Al XLPE FRLS LH Cable

i) 3.5C x 35Sqmm Al XLPE FRLS LH Cable

j) 4C x 25Sqmm Al XLPE FRLS LH Cable

k) 4C x 16Sqmm Al XLPE FRLS LH Cable

l) 4C x 16Sqmm Cu Flex. FRLS LH Cable

m) 4C x 10Sqmm Cu XLPE. FRLS LH Cable

n) 4C x 6Sqmm Cu XLPE. FRLS LH Cable

o) 4C x 4Sqmm Cu XLPE FRLS LH Cable

p) 4C x 2.5Sqmm Cu XLPE FRLS LH Cable

q) 4C x 10Sqmm Cu Flex. FRLS LH Cable

r) 3C x 6Sqmm Cu XLPE FS Cable

s) 3C x 6Sqmm Cu Flex. FRLS LH Cable

t) 3C x 2.5Sqmm Cu XLPE FS Cable

u) 3C x 2.5Sqmm Cu XLPE FRLS LH Cable

v) 3C x 2.5Sqmm Cu Flex. FRLS LH Cable

Supplying, terminating, connecting & commissioning the above underground cables with double compression type glands with all sockets etc complete i) 3.5C x 300Sqmm Al XLPE FRLS LH Cable

ii) 3.5C x 240Sqmm Al XLPE FRLS LH Cable

iii) 3.5C x 240Sqmm Al XLPE FS Cable

iv) 3.5C x 150Sqmm Al XLPE FRLS LH Cable

v) 3.5C x 120Sqmm Al XLPE FRLS LH Cable

vi) 3.5C x 95Sqmm Al XLPE FRLS LH Cable

vii) 3.5C x 70Sqmm Al XLPE FRLS LH Cable

viii) 3.5C x 50Sqmm Al XLPE FRLS LH Cable

ix) 3.5C x 35Sqmm Al XLPE FRLS LH Cable

x) 4C x 25Sqmm Al XLPE FRLS LH Cable

xi) 4C x 16Sqmm Al XLPE FRLS LH Cable

xii) 4C x 16Sqmm Cu Flex. FRLS LH Cable

xiii) 4C x 10Sqmm Cu XLPE. FRLS LH Cable

xiv) 4C x 6Sqmm Cu XLPE. FRLS LH Cable

xv) 4C x 4Sqmm Cu XLPE FRLS LH Cable

xvi) 4C x 2.5Sqmm Cu XLPE FRLS LH Cable

xvii) 4C x 10Sqmm Cu Flex. FRLS LH Cable

xviii) 3C x 6Sqmm Cu XLPE FS Cable

xix) 3C x 6Sqmm Cu Flex. FRLS LH Cable

xx) 3C x 2.5Sqmm Cu XLPE FS Cable

xxi) 3C x 2.5Sqmm Cu XLPE FRLS LH Cable

xxii) 3C x 2.5Sqmm Cu Flex. FRLS LH Cable

8.00) STRUCTURAL EARTHING I) Foundation Earthing Supply of 10 mm copper bonded Solid Steel Round Conductor with average coating thickness minimum of 100µm for Type-B Earthing and should be tested for Tensile strength, Electrical Resistance, salt mist, Bend & Adhesion to meet the requirements of IS/ IEC 62305 and IEC 62561-1&2.

Supply of 18 mm copper bonded Solid Steel Round Conductor with minimum coating thickness 70µm as integrated down conductor. Material should be tested Tensile strength, Electrical Resistance, salt mist, Bend & Adhesion to meet the requirements of IS/ IEC 62305 and IEC 62561-1&2.

Supply of stainless steel Straight Connector at every 5Mtr of integrated down conductor for interconnecting 10 mm dia copper bonded round conductor at straight connection Test Para1 RMTs: a) Static Mechanical Test b) Environmental Test Tested as per IEC 62561-1

Supply of 18mm stainless steel Straight Connector at every 5 Mtr of integrated down conductor and should be tested for electrical resistivity, mechanical load to meet the requirement for IS/IEC - 62305 and IEC 62561-1&2.

Supply of Stainless steel 304 Grade Cross Connector for 16-18 mm Copper bonded conductor at cross/Tee junction. Test Parameter a) Mechanical Load b) Electrical Test c) ENvironmental Test Tested for IEC 62561-1

Supply of Stainless steel 304 Grade Cross Connector for 8 mm dia Aluminium alloy round conductor & 10 mm Copper bonded conductor at cross/Tee junction. Test Parameter a) Mechanical Load b) Electrical Test c) ENvironmental Test Tested for IEC 62561-1

Supply of Corrosion Bitumen tape for inside soil.

Structural Down Conductors - Raiser Supply of 10 mm Copper bonded Steel Round Conductor as integrated down conductor. Material should be tested Tensile strength, Electrical Resistance, salt mist, Bend & Adhesion to meet the requirements of IS/ IEC 62305 and IEC 62561-1&2.

Supply of Bonding clamp for interconnecting Round Conductor with reinforcement rebar at every 3Mtr inside the concrete to meet the requirements of IS/IEC 62305.

Supply of Earthing stud & suitable Clamp of dimension 69 x 69 mm used in structural steel ring earthing system to meet the requirements of IS/IEC 62305. (for interconnecting Air termination and structral down conductors)

External Lightning Protection System -Air Termination System and Inter-Connection Supply of 8mm dia Aluminium alloy Solid Round Conductor of material AlMgSi used in air termination system . Cross sectional area of conductor should be 50 mm². Test Parameter: a.Lightning impulse current of 100kA for 10/350 µs b.Electrical resistivity - 0.034 µΩm, c.Tensile strength - 178 MPa or N/mm² d. Salt spray - No Sign of Corrosion. Tested as per IEC 62561-2.

Supply of Nylon Conductor Holder for Parapet wall for holding 8 mm dia Aluminium alloy round Conductor.

Supply of Nylon roof conductor holder for flat roof with concrete block for fixing 8 mm dia Aluminium alloy Solid Round Conductor in the terrace flat surface at every 1 mtr.

Supply of Expansion Joint with connector to compensate the expansion and contraction of Solid Round Al. Conductor during temperature variations. Expansion Joint should be consider at every 20 mtr length of straight horizontal air termination and connected at both the end with use of straight connector conductor.

Supply of Aluminium Straight conductor connector for interconnecting 8mm Aluminium conductor to meets the requirement of IS/IEC 62305. Test Para1 RMTs: a) Mechanical Load b) Electrical Resistivity c) Environmental Test Tested as per IEC 62561-1

Supply of air termination rod of 2mtr length of material AlMgSi of dia1 RMT ø 16/10 mm crimped on both the ends (Tappered Type). The rod shall be mounted with stainless steel clamp and fixing accessories . Test Parameter for 2 mtr vertical air terminal a)ELectrical Resistivity b) Tensile Strength c) Condition of Salt Mist Tested as per IEC 62561-2. Test Para1 RMTr for Wall clamp a) Mechanical load as per IEC 62561-1

Supply of air termination rod of 3 mtr length of material AlMgSi of dia1 RMT ø 16/10 mm crimped on both the ends(Tappered Type). The rod shall be mounted with stone and fixing accessories . Test Parameter for 3 mtr vertical air terminal a)ELectrical Resistivity b) Tensile Strength c) Condition of Salt Mist Tested as per IEC 62561-2.

Supply of stainless steel Earth stud of dimension 69 x 69 mm integrated inside concrete and should be tested for electrical resistivity, salt spray and humidity test & short circuit to meet the requirements of IS/IEC 62305 and IEC 62561-1&2. (for interconnecting Air termination and structral down conductors)

Supply of CAPE make connecting point made of stainless steel for terminating 10mm copper conductor.

Supply of Air termination rod made up of material AlMgSi of dia1 RMT Ø 10 mm. The rod shall be connected to the horizontal air termination using stainless steel connector to meet the requirement of IS/IEC 62305.

Supply of Stainless steel SS 304 Grade Folding Clamp as per sheet profile for 8 mm dia Aluminium alloy Solid Round Conductor for horizontal Air terminal above metal sheet to meet the requirements for IS/IEC 62305. Test Parameter: a) Mechanical Load b) Environmental Test Tested as per IEC 62561-4

TN-S PME Earthing System Supply of 18 mm copper bonded Solid Steel Round Conductor with minimum coating thickness 70µm as integrated down conductor. Material should be tested Tensile strength, Electrical Resistance, salt mist, Bend & Adhesion to meet the requirements of IS/ IEC 62305 and IEC 62561-1&2.

Supply of Bonding clamp for interconnecting Round Conductor with reinforcement rebar at every 3Mtr inside the concrete to meet the requirements of IS/IEC 62305.

Supply of Diagonal clamp MS for interconnecting 10 mm Round Conductor with reinforcement rebar at every 3Mtr inside the concrete to meet the requirements of IS/IEC 62305.

Supply of stainless steel Straight Connector at every 5Mtr of integrated down conductor for interconnecting 10 mm dia copper bonded round conductor at straight connection Test Para1 RMTs: a) Static Mechanical Test b) Environmental Test Tested as per IEC 62561-1

Supply of MS cross connector for 10 mm round conductor at cross junction.

Supply of suitable MS cross connector for 18 mm round conductor inside concrete and should be tested for electrical resistivity and mechanical load to meet the requirement of IS/IEC - 62305 and IEC 62561-1&2.

Supply of stainless steel Earth stud of dimension 69 x 69 mm integrated inside concrete and should be tested for electrical resistivity, salt spray and humidity test & short circuit to meet the requirements of IS/IEC 62305 and IEC 62561-1&2.

Supply of Earthing stud with fixing clamp accessories of dimension 69 x 99 mm used in structural steel ring earthing system to meet the requirements of IS/IEC 62305. Rated Current (CPRI TESTED): Irms- 8 KA; Ipeak- 17 KA Per sec

Supply of SS Earthing stud with fixing clamp accessories of dimension 79 x 149 x 205 mm used in structural steel ring earthing system to meet the requirements of IS/IEC 62305. Rated Current (CPRI TESTED): Irms- 9 KA per sec; Ipeak-21 KA per sec

Supply erection testing and commissioning of Maintenance Free Earthing system comprising of 14.2 mm dia 3 mtr long Earth electrode of low carbon steel electrode with 250 micron copper bonding & 1 bag of Carbon based Ecosafe environment friendly backfill RMG .. 4 1 Sets

Supplying, laying and connecting 50 x 6 mm. GI Flat laid in open fashion with necessary clamps,screws, interlinks etc for inter connecting of the earth pits

Supplying, laying and connecting 25x 6 mm. Cu Flat laid in open fashion with necessary clamps,screws, interlinks etc for Neutral Earthing of transformer & DG 1 Set

Supplying, laying and connecting 50 x 6 mm. GI Flat laid in open fashion with necessary clamps,screws, interlinks etc for Body Earthing of transformer, DG 1 Set & Main LT Panel

Supplying, laying and connecting 25 x 6 mm. GI Flat laid in open fashion with necessary clamps,screws, interlinks etc for Body Earthing of Sub Panels Etc.,

Supplying, laying and connecting 25 x 3 mm. GI Flat laid in open fashion with necessary clamps,screws, interlinks etc for Body Earthing of Lift Etc.,

Supplying, laying and connecting 8SWG Cu wire laid in open fashion with necessary clamps,screws, interlinks etc for earthing of All DBs ,Fans, Lift & AC Equipments

Supplying, laying and connecting 1C x 10Sqmm Cu FRLS LH wire laid in open fashion/in cable tray / PVC conduit with necessary clamps,screws, for earthing of UPS

Supplying, laying and connecting 1C x 6Sqmm Cu FRLS LH wire laid in open fashion/in cable tray / PVC conduit with necessary clamps,screws, for earthing of UPS

Supplying, laying and connecting 1C x 4Sqmm Cu FRLS LH wire laid in open fashion/in cable tray / PVC conduit with necessary clamps,screws, for earthing of Inverter

9.00) SAFETY EQUIPMENTS i) Supplying, erecting and connecting Treatment Chart in English and Local Language directly fixed on to the wall with necessary screws etc.

ii) Supplying 440 V Gloves

iii) Supplying 11 KV Gloves

iv) Supplying, and laying 2000 mm. x 1000 mm x 3 mm. thick 3.3kV ISI Marked Synthetic mats to be laid in Front of the Panel Boards.

v) Supply & fixing of First aid box of Thadani make containing full compliment of medicines, ointments & bandages etc.,

vi) Supplying and fixing 11 KV Danger Boards

vii) Supplying and fixing 440 V Danger Board.

viii) Supply & fixing of 230V, 2X11W PL Lamp AC portable & re chargeable emergency light with LED Light of BPL/Panasonic Make

ix) Supply of 11KV Earth discharge rod made of FRP complete with earth terminal & 10sqmm copper pvc insulated conductor of 10mtr length.

x) Supply & fixing of 60X40cm teak wood box with glass door& hooks for hanging keys& space for keeping hand gloves complete with lock & three keys

xi) Supply & Installation of cast iron HT cable route markers with necessary angle iron supports& civil works (Gate to RMG)

CABLE TRAY Supplying,erecting & connecting and commissioning Cable Trays of following measurements with necessary Box Channel for cable supports and other allied fabrication works i) 900 x 75 x 2mm Ladder Type Cable Tray

ii) 750 x 75 x 2mm Ladder Type Cable Tray

iii) 600 x 75x 2mm Ladder Typer Cable Tray

iv) 450 x 50 x 1.6mm Ladder Type Cable tray

v) 300 x 50 x 1.6mm Ladder Type Cable Tray

vi) 150 x 50 x 1.6mm Ladder Type Cable tray

viii) 150 x 50 x 1.6mm perforated Type Cable tray

ix) 300 x 50 x 1.6mm perforated Type Cable tray

x) 450 x 50 x 1.6mm perforated Type Cable tray

xi) 600 x 50 x 2mm perforated Type Cable tray

Supply & Installation of 150mmx 100mm Powder coated Trunking 1.6mm thick with cover to be used for running the wires/cables near the DB locations.

LIGHT POINT WIRING Mains Wiring (DB to Switch Board) & DB to First point of MCB controlled light i) Supplying, wiring, connecting & commissioning the Light Points with 3 Runs of 2.5 Sqmm. PVC Insulated multistranded copper conductor FRLS LH wires

PRIMARY POINT WIRING ii) Supplying, wiring, connecting & commissioning the Primary Light Points with 3 Runs of 1.5 Sqmm. PVC Insulated multistranded copper conductor FRLS LH wires

SECONDARY POINT WIRING iii) Supplying, wiring, connecting & commissioning the Secondary Light Points with 3 Runs of 1.5 Sqmm. PVC Insulated multistranded copper conductor FRLS LH wires

12) EMERGENCY LIGHT POINT WIRING Supplying, wiring, connecting & commissioning the Light Points with 3 Runs of 2.5 Sqmm. PVC Insulated multistranded copper conductor FRLS LH wires

13) RAW POWER WIRING i) Supplying, wiring, connecting & commissioning the Power Points with 3Core 4 Sqmm. PVC Insulated multistranded copper conductor FRLS LH wires

ii) Supplying, and fixing 6/16 AMPS Switched Socket combined in 1.6 mm. thick in Manufacturer's mounting box fixed flush with the wall. - FOR RAW POINT WIRING & UPS POWER WIRING

iii) Supplying, and fixing 6 AMPS Switched Socket combined in 1.6 mm. thick in Manufacturer's mounting box fixed flush with the wall. - RAW POWER & UPS POWER

iv) Supply Installation, testing and commissioning of 16A single phase metal Clad sockets with 16A DP/SP MCB as control with manufacturer's enclosure at Floor/Wall including interconnection with 4 Sq.mm.flex cables and terminations.

14) UPS POWER WIRING Supplying, wiring, connecting & commissioning the Power Points with 3C x 4 Sqmm. PVC Insulated FRLS LH multistranded copper conductor cable in 25mm heavy duty GI conduit laid in open fashion above false ceiling with necessary clamps, screws, etc.,

Supplying, wiring, connecting & commissioning the Power Points with 3C x 4 Sqmm. PVC Insulated FRLS LH multistranded copper conductor cable in already laid conduit/raceways in open fashion above false ceiling with necessary clamps, screws, etc.,

Supplying, wiring, connecting & commissioning the Power Points with 3C x 2.5 Sqmm. PVC Insulated FRLS LH multistranded copper conductor cable in already laid conduit/raceway laid in open fashion above false ceiling with necessary clamps, screws, etc.,

Supplying, and fixing 2 x 6 AMPS Socket controlled by 1No. 16A Switch combined in 1.0 mm. thick in Manufacturer's mounting box fixed flush with the wall.

Supplying, and fixing 3 x 6 AMPS Socket controlled by 1No. 16A Switch combined in 1.0 mm. thick in Manufacturer's mounting box fixed flush with the wall.

15) PVC/GI FLEXIBLE HOSE Supply and laying of PVC/GI Flexible Hose with all necessary accessories i) 25mm GI Flexible Hose

16) PVC/GI CONDUIT Supply and laying of heavy duty PVC conduit concealed in wall/floors/ceilings with necessary clamps, screw with 1 Run of 16SWG G.I. Fish wire i) 25mm heavy duty PVC Conduit. - FOR ELECTRICAL CONTRACTS & NETWORKING

ii) 25mm heavy duty GI Conduit.

17) RACEWAYS Supplying, fabricating, laying and connecting the following GI/Aluminium Race Ways of 1.6mm. thick embedded in the floor/ceiling. For Electrical & Networking Cables in Floor a) 60 x 40 mm. Al Raceway with suitable Cover

b) 100 x 40 mm. Al Raceway with suitable Cover

c) 150 x 40 mm. Al Raceway with suitable Cover

For Electrical & Network Cables in Ceiling with suitable supports a) 60 x 50 mm. Powder coated Raceway with suitable Cover

b) 100 x 50 mm. Powder coated Raceway with suitable Cover

c) 150 x 40 mm. Al Raceway with suitable Cover Note:- All Raceways are with cover only.

18.00) CEILING/FLOOR JUNCTION BOXES Supplying, erecting 14 G thick Junction boxes with cover of 50 mm. height of suitable sizes as per Site conditions. The Ceiling/Floor Junction boxes shall be fixed flush with the floor (powder coated) i) 100mm x 100mm Junction Box

ii) 200mm x 150mm Junction Box

iii) 350mm x 150mm Junction Box

19.00) FLOOR CUTTING Charges for cutting RCC Floor over & above the depth as required for fixing of raceway upto a depth of 50mm as per site condition

20.00) HUME PIPE Supply and laying of heavy duty Hume Pipe in underground at depth of 1.0Mtrs, excluding the earth excavation and refilling of the excvated soil, etc., complete as per site condition. i) 450mm Hume Pipe Class: NP-2

ii) 300mm Hume Pipe Class: NP-2

iii) 200mm Hume Pipe Class: NP-2

LIGHT FIXTURES Supply Installation testing and commissioning of light fixtures i) Supply installation testing and commissioning of LED light with system wattage of 20W (±10%). CCT shall be 4000K and CRI ≥ 80. Housing shall be synthetic chrome/Engineering plastic with IP20 protection. The THD shall be ≤ 20% with suspended rod

ii) Supply installation testing and commissioning of LED light with system wattage of 20W (±10%). CCT shall be 4000K and CRI ≥ 80. Housing shall be synthetic chrome/Engineering plastic with IP20 protection. The THD shall be ≤ 20%.

Supply installation testing and commissioning of Recess mounted LED downlighter with system wattage as 18W(±10%) & system lumens not less than 2200lm lumens.

Supply installation testing and commissioning of Recess mounted LED downlighter with system wattage as 12W(±10%) & system lumens not less than 2200lm lumens. The system efficacy shall be ≥100 lm/W CCT.

Supply, installation, testing, and commissioning of wall-mounted 12W LED light fixture, complete with all accessories

Supply installation testing and commissioning of LED Bulkhead light with system wattage of 10W to 11W & minimum system lumen output of 1000lm.. CCT shall be 6500K/5700K/4000K

Supply & Installation of Standard commercial roadway lighting poles of 6.0mtr height with control box, 4way loop in loop out connectors suitable for 3C x 2.5Sqmm Cu cable, SP MCB ,

Supply installation testing and commissioning of 30W LED street light with SMD type LED having minimum system efficacy of ≥ 100 lm/W using cool white LEDs made up of Pressure Die

Supply installation testing and commissioning of LED linear 2' surface mounted luminaire with system wattage not more than 9W to 11W. The system lumen shall be 1100 lm with system efficacy of ≥ 100 lm/W. CRI shall be ≥ 80

Supply, installation, testing, and commissioning of Passive Infrared (PIR) presence/motion sensor, suitable for automatic control of lighting based on occupancy detection, Ceiling mounted, detection range of 7 meters (diameter), Detection angle of 360° (ceiling type) complete with all necessary mounting accessories, wiring, and connections.

Supply, installation, testing, and commissioning of 2’x2’ (600x600mm) clean room type LED light fixture consuming a system wattage of 30W (±10%) delivering an initial system lumen of 3000 lumens & the luminaire

Supply, installation, testing, and commissioning of decorative ceiling-mounted dome light fixture consuming a system wattage of 20 - 25W (±10%) with integrated LED or lamp holder, suitable for surface

Supply installation testing and commissioning of Recess mounted LED 2'x2' luminaire consuming a system wattage of 30W (±10%)

Supply, installation, testing, and commissioning of flexible LED strip light (cove lighting) consuming a system wattage of 5W/mtr

Supply, installation, testing, and commissioning of LED downlight with integrated motion sensor (PIR type), output range of 800W Resistive load/ 400W

22.00) JUNCTION BOX / AVIATION LIGHT/ISOLATORS Supply, erection, testing and commisioning of junction box of following specification complete 1 Set for street light fixtures. i) Supply of 6Way 16A Terminals in weather proof thermo plastic box with 3Nos. Of cable gland suitable for 3C x 4Sqmm Cables make - Hensel.

ii) Supply of LED AVIATION OBSTRUCTION light with red colour LEDs, intensity 30 candela in one direction, total intensity 600 candela (Type - L1 - 300)

iii) Supply erection testing and commissioing of isolator in a sheet steel enclosure to be fixed near by the equipment in wall with all accessories a) 100A 4P 100mA RCBO with IP65 protection

b) 63A 4P 100mA RCBO with IP65 protection

c) 32A 4P 100mA RCBO with IP65 protection

d) 63A 4P isolator MCB Type with IP65 Protection

e) 32A 4P Isolator MCB Type

f) 63A 4P Isolator MCB Type

g) 25A 4P Isolator MCB Type

h) 40A 4P Isolator MCB Type

iv) Supply , Installation , Testing & Commisioning of remote ON/OFF LOCKABLE push button station Mounted on wallwith suitable size MS powder Coated MS Box with space provision to terminate incoming and outgoing of suitable size cable. ( For Fans/Pumps/Motors) with IP55 Protection

20kVA UPS Supply, Installation, Testing and Commissioning of 3 Phase in put & 3Phase out put 20kVA Conventional UPS configuration using IGBT rectifier & IGBT Inverter to achieve Unity IPF & <3% THDi as per the enclosed technical data sheet. Modbus connectivity and load testing at site complete 1 Set

10kVA UPS Supply, Installation, Testing and Commissioning of 3 Phase in put & 3Phase out put 10kVA Conventional UPS configuration using IGBT rectifier & IGBT Inverter to achieve Unity IPF & <3% THDi as per the enclosed technical data sheet. Modbus connectivity and load testing at site complete 1 Set

5kVA Inverter Supply erection testing and commissioning of 5kVA Inverter with 90Minutes battery back up

1.5kVA Inverter Supply erection testing and commissioning of Single Phase I/P and Single Phase output 1.5kVA Inverter with 90Minutes battery back up

CAR CHARGING POINT Supply, installation, testing, and commissioning of Electric Vehicle (EV) Charging Points suitable for charging electric cars in designated parking spaces.

NETWORKING WORKS 1) TELEPHONE, TV & DATA CABLES Supply and laying of cables in already laid PVC Conduit concealed in wall/floors/ceilings with necessary clamps, screw etc., i) CAT6 cable UTP (305M)

ii) 7 ft Modular Mounting Cord for Active Data User Side (Yellow color)

iii) 7 ft Modular Mounting Cord for Active Data Rack side (Yellow color)

iv) RG6 TV Cables

2) DATA SOCKET Supplying, and fixing Cat6 RJ45 Socket in 1.6 mm. thick in Manufacturer's mounting box fixed flush with the wall.

3) TELEPHONE SOCKET Supplying, and fixing of Cat6 RJ11 Socket in 1.0 mm. thick in Manufacturer's mounting box fixed flush with the wall.

4) TELEVISION SOCKET Supplying, and fixing TV Socket in 1.6 mm. thick in Manufacturer's mounting box fixed flush with the wall.

5) JACK PANELS Supply erection testing and commissioning of Jack panels of following specification i) 24Port Patch Panel

NETWORKING RACKS Supply erection testing and commissioning of racks with all accessories like PDU, cable manager etc complete of following specification i) 36U Rack with all accessories

ii) 15U Rack with all accessories

iii) 9U Rack with all accessories

iv) 6U Rack with all accessories

v) 21U Rack with all accessories

7) DATA CABLE TESTING Scanner testing for data cabling

FIBER CABLE FOR FLOOR TO FLOOR CONNECTIVITY Supply and laying of cables in already laid PVC Conduit concealed in wall/floors/ceilings with necessary clamps, screw etc., i) 6 Core Multimode outdoor type Fiber Optic Cables

ii) End 24port LIU with slicing tray

iii) LC Pigtile -1Mtrs

iv) Patch code SC to LT -3Mtrs

HDMI POINT Supply and installation of HDMI point including HDMI wall plate with female connectors, concealed in wall or surface mounted trunking

USS 630KVA, 11KV/433V outdoor Dry Type Resin Cast Transformer with OLTC/RTCC/AVR and as per the data sheet

RING MAIN GEAR (RMG) 11KV 25KA 630Amps HT RING MAIN GEAR comprising of Two Incoming Air Break Load Break Switches and One Outgoing HT Vacuum Circuit Breaker for INDOOR Installation

DG 1 Set Supply and Erection of 415V 3Ph 650 KVA (Prime Duty), diesel generating 1 Set with accoustic enlcosure along with radiator type cooling arrangements and associated accessories including, starting batteries, AVM Pads, fuel tank, Residential Silencers and as per the specification complete 1 Set. Including freight charges.

2) ERECTION OF DG 1 SetS a) Unloading & Positioning of the 625 KVA DG 1 Set in the prepared foundation, rection testing and commissioning of DG 1 Set

b) Supply and Erection of 10" Dia M.S. B-Class Pipe with all necessary bends, flanges and reducers-5mm thickness

c) Thermal Insulation for Residential Silencers.

d) Thermal Cladding for 10" Dia Piping with 24G Aluminium Sheets-(50mm thick 96kg/cm3 density Rockwool)

e) Supply & Erection of Exhaust Bellow with Necessary Accessories

f) M.S angles & channels with enamel paint for support of Exhaust Pipes and Fuel Pipes And Structure for DG 1 Sets etc..

CONTROL CABLING Control cabling between DG 1 Sets, Main LT Panel & Synchronizing Panel with necessary cables and other accessories complete 1 Set. a) Supply & installation of 3cx2.5 Sqmm Cu arm.Multistrand cables with Double compression gland End termination

b) Supply & installation of 4Cx2.5 Sqmm Cu arm.Multistrand cables with Double compression gland End termination

c) Supply & installation of 12Cx2.5 Sqmm Cu arm.Multistrand cables with Double compression gland End termination

d) Supply & installation of 4cx4 Sqmm Cu arm.Multistrand cables with Double compression gland End termination

e) Supply & installation of 150mmx50mmx2mm thick Perforated type cable tray

f) Supply & installation of 25x6mm thick GI strip

PHE works SANITARY FIXTURES Supply,Installation, Testing and Commissioning of Vitreous china Wall mounted Europian water closet having back inlet with in-built siphonic P Trap and Dual flush type concealed flushing cistern 4/2 Litres Per Flush Location - All floor toilets

2) Supplying and fixing of best approved quality of following CP water supply/Sanitary fittings confirming to I.S. specification b) CP two Way bib cock with health faucet (<= 4 LPM)

3) Supply , Fixing, testing and commissioning of WHITE coloured vitreous china under counter Regular rectangular & Oval WASH BASIN with brackets / G.I. rag bolts and nuts painted, 32mm dia brass C.P. waste coupling, (heavy) 32mm dia brass C.P. bottle trap & etc., The work shall include,required extension nipples, cutting / chasing and making good the walls and floors - toilets.Location - All floor toilets

4) Supply and Fixing of wash basin Brass Chromium Plated Pillar Tap (Heavy Type) - 15 / 12mm dia, required cp flanges & etc complete,Location-wash basin.

5) Supplying and fixing of brass Chromium Plated Towel Rail 60cm long and 20mm dia with Brackets, including cost of screws, TW plugs and labour charges for fixing in position etc. complete in all respects and as directed by the departmental officers.

6) Supply & fixing of Toilet paper holding including brass screws, washers, and cutting, making finishing the wall surface with necessary fittings and accessories.

7) Supply & Fixing of stainless steel twin coat hook fixed to wooden cleats with CP brass screws. Location - All floor toilets

8) Supplying, fixing, testing and commissioning, Stainless steel sink with single bowl and double drain board manufactured from 1 mm thick stainless steel, 18G high grade. Location - Pantry & lab area. a) Single bowl sink (1040 mm x 510 mm)

b) Single bowl (1200 x 550 x 180mm ) (For lab quantity assumed-ID not available)

9) Supply and Fixing of chromium plated angle valve with SS braided hose-18 inches long with nut and rubber washer complete as required.

10) Supply , Fixing, testing and commissioning of urinal with automatic flushing systems <= 2.5 LPF to ensure pre-flush & flushing only

Supply and fixing of Automatic Electrical Water Heater with copper container, with Glass Wool / Puf Insulation with MS powder coated shell suitable for following capacity 230V / 1000W (Higher End) a) 25 Litres

II) SOIL, WASTE, VENT AND RAIN WATER PIPES Supplying, fixing and testing and commissioning of UPVC soil and waste pipes (SWR) confirming to IS 13592 :1990, type B Location: Inside Toilet a) 75mm dia

b) 110mm dia

2) Supplying, fixing and testing and commissioning of UPVC soil, waste and vent pipes (SWR) confirming to IS 13592 :1990, type B Location :Shaft & ceiling pipe a) 63mm dia (Vent)

b ) 75mm dia

c) 110mm dia

3) Supplying ,fixing, testing and commissioning of PVC pipe confirming to IS 4985 of Agricultural series - 6 kgs / sq.cm pressure rated, Location: External soil & waste pipe a)110mm dia

b)160mm dia

4) Supply, Installation, Testing and Commissioning of mineral filled 3 layered (PP/PP mineral filled/PP) Polypropylene low noise pipes and fittings of min. density 1.9 gm/cm3, pipes of 40 mm – 200 mm - FOR LABORATORY WASTE LINES a)75mm dia

b)110mm dia

c)160mm dia

5) Supplying, fixing and testing uPVC pipe class V pipes (10 Kg/sqcm) confirming to IS:4985:2000 for waste connection from wash basin, kitchen sinks to floor trap / anti syphonage pipe with solvent cement joints, hanging rods including all the fittings, laid under floor / concealed in wall etc., the work shall include wall chase and making good the same in cement mortar etc., complete. Location: Internal WB & UR connection pipe a) 50mm dia (For kitchen sink & washing machine)

b) 40mm dia (For toilet & other area hand wash)

6) Supply, Installation, testing and commissioning Rain water pipe confirming to IS 4985 of SWR Class - III (6 Kg/sqcm) quality pressure rates as mentioned Location :Shaft & ceiling (RWP) a) 160 mm dia

7) Supplying ,fixing, testing and commissioning of PVC pipe confirming to IS 4985 of Agricultural series - 6 kgs / sq.cm pressure rated, for underground soil, waste and vent laid under the soil from manhole to manhole outside the building. Location: External rain water pipe a) 160mm dia

b)200mm dia

8) Supplying and fixing of Leaf trap with kurra made out of PVC with flange and grating for rain water outlets on terrace etc., complete. a) 160 mm dia

9) Supply, fixing and testing PVC Floor Trap (Necessory of multitrap connection (heavy duty hinged type trap of 100 mm dia inlet and 75 mm dia outlet fixed on a bed of cement concrete etc.complete.)

10) Supplying and fixing of SS heavy grating cover (Cockroach trap) (150 mm x 150 mm). etc., complete. (The frame and grating shall be approved by Architects) ( Chilly Make grating only )

11) Supply,Laying, Testing and Commissioning of PVC Cleanout with heave duty nickel bronze gasket cover for Soil, Waste pipes inside the Toilet area and making it complete for operation. a) 75 mm dia

b) 110 mm dia

III) WATER SUPPLY SYSTEM (WATER PIPE & ACCESSORIES) Cold water pipe: Supplying, fixing, jointing, testing and commissioning of approved make Chlorinated Polyvinyl Chloride pipes (CPVC) up to 50 mm dia SDR 11 as per IS 15778: 2007 & SDR 11 fittings as per ASTM D2846 / D2846M - 14 a) 20 mm nominal dia

b) 25 mm nominal dia

c) 32 mm nominal dia

d) 40 mm nominal dia

e) 50 mm nominal dia

2) Supplying and fixing full way lever operated of following dia of gun metal ball valve (Heavy Duty) a) 20 mm dia

b)25 mm dia

c) 32 mm dia

d) 40 mm dia

e) 50 mm dia

3) Supply, installation, testing and commissioning of butterfly valve ( IS 13039) of CI body SG iron rilson coated disc ,Working pressure not less than 10Kg/Sq.cm. Including rubber gasket, flanges, nuts, bolts, washers & painting a) 65 mm dia

b) 100mm dia (Gate valve)

4) Supplying & fixing screwed ended gun metal horizontal / vertical non return valve conforming to IS 5312 of PN 10 pressure rating b) 100 mm nominal dia

5) Supplying & fixing of brass Auto Air vent with isolation valve for cold water supply risers, suitable for working pressure not less than 10 Kg/Sq.cm a) 20 mm dia

6) Supply and installation of 65mm∅, 80mm∅ &100mm∅ electromagnetic flow meter - equipped and connected with data logger sensor, ABB type or equivalent, a) 50 mm dia

b) 100 mm dia

7) Supply Installation, testing & commissioning of dual flange CI `Y' strainer PN10 (flanged) with stainless steel fine wire mesh perforated sheet basket with necessary flange / unions, nuts, bolts and wahsers etc with following sizes. a)100 mm dia

IV) PUMPS & ACCESSORIES 1) Supplying, installing, testing and commissioning of Domestic Water Transfer Pump for domestic OHT Filling of continuous duty submersible centrifugal non-clogging pumps complete with 3 phase motor. 2 nos. (1 working + 1 standby) Pump capacity - 2.5 LPS Head - 45 TO 50 mtrs

2) Supply, Installation, testing and commissioning of domestic water booster pump 1 Set with diaphragm type pressure 2 nos. (1 working + 1 standby) vertical or horizontal in line, multistage, centrifugal pumps complete in S.S. coupled with TEFC motor. Pump capacity - 3 Lps Head - 20 mtrs Motor Power ± : kw

3) Supply, Installation, testing and commissioning of gardening / excess water transfer pump submersible with electric control panel 2 nos. (1 working + 1 standby) Pump capacity - 2 LPS Head - 20 mtrs

4) Supply, installation in position, testing and commissioning of electrically driven Submersible Dewatering pumps of Semi-open non clog impeller with control panel a) Location: Pump room drain sump Pump capacity - 2.7.0 LPS/ each Head - 10 to 15 meters

V) ETP & ACCESSORIES Supply, installation, testing and commissioning of 10 Kld capacitie of Effluent Treatment Plant consists of units like Bar screen, Raw effluent transfer pumps (2 nos ( 1 w + 1 s )

VI) EXTERNAL MANHOLE & ACCESSORIES Providing and constructing as per detailed drawing Manhole/ chamber Providing and constructing inspection chamber internal dimension of size 600 mm x 600 mm in 230 mm thick using fly ash brick masonry in CM 1:4, over a bed of 200mm thick M10 grade (20mm metal)

Providing and constructing inspection chamber internal dimension of size 1200 mm x 900 mm using fly ash brick masonry min crushing strength of 5 N/sq.mm., of varying thickness (230mm thick upto 1.0m , 345mm thick above 1.0m to 2.0m, 450mm thick wall above 2.0m to 2.5m) in CM 1:4, over a bed of 200mm thick M10 grade (20mm metal)

Supply and fixing in position Upvc Gully traps 150 x 150mm size with cover including masonry chamber with 200 mm thick wall of clear internal size as 300mm x 300mm with cement plaster 12mm finishes

Supply and fixing in position Upvc Gully traps 150 x 150mm size with cover including masonry chamber with 200 mm thick wall of clear internal size as 450mm x 450mm

Providing and constructing rain water collection chamber internal dimension of size 450 mm x 450 mm in 230 mm thick using fly ash brick masonry in CM 1:4, over a bed of 200mm thick M10 grade (20mm metal)

Supply and installation of Rain Water Percolation pits - 1200 mm in diameter up to 3200 mm deep, bottom 500 mm filled with boulders 150 - 230 mm size

VII) CIVIL WORKS / MISCELLANEOUS ITEMS Providing and fixing 600 mm long MS hot dip galvanized PUDDLE FLANGES fabricated out of 8 mm thick MS plates of suitable size and IS:1239 heavy class pipes a) PUDDLE FLANGES FOR OHT 50 mm dia (screwed ends)

65 mm dia (flanged ends)

150 mm dia (flanged ends)

b) PUDDLE FLANGES FOR UG SUMP 50 mm dia (screwed ends)

100 mm dia (flanged ends)

150 mm dia (flanged ends)

Supplying, fixing, jointing, testing and commissioning of approved make Chlorinated Polyvinyl Chloride pipes (CPVC) up to 50 mm dia SDR 11 as per IS 15778: 2007 & SDR 11 fittings as per ASTM D2846 / D2846M - 14, both of approved make PIPE INSIDE THE S. LAB , ALL CEILING PIPE & ETC a) 20 mm nominal dia

b) 25 mm nominal dia

c) 32 mm nominal dia

d) 40 mm nominal dia

e) 50 mm nominal dia

Supplying & fixing full way lever operated gun metal ball valve (IS-9890 -1981) working pressure not less than PN10 with threaded joints a) 20 mm dia

b)25 mm dia

c) 32 mm dia

d) 50 mm dia

Supplying & fixing screwed ended gun metal horizontal / vertical non return valve conforming to IS 5312 of PN 10 pressure rating e) 50 mm nominal dia

Supply and installation of 65mm∅, 80mm∅ &100mm∅ electromagnetic flow meter - equipped and connected with data logger sensor, ABB type or equivalent a) 50 mm dia

Supply Installation, testing & commissioning of dual flange CI `Y' strainer PN10 (flanged) with stainless steel fine wire mesh perforated sheet basket a)50mm dia

II) PUMPS & ACCESSORIES Supply, Installation, testing and commissioning of DM water booster pump 1 Set with diaphragm type pressure vessel, electronic pump controller, pressure switch, pressure transmitter, electrical wiring, cabling with cable tray as specified, level controller 2 nos. (1 working + 1 standby) vertical or horizontal in line, multistage, centrifugal pumps complete in S.S. coupled with TEFC motor. Pump capacity - 2.5 Lps Head - 20 mtrs

III) DEMINERALIZATION PLANT & ACCESSORIES Supply, installation, testing and commissioning of DM water treatment plant with automatic back wash system, which contains filter feed pump 1 Set -2 Nos (1 W + 1 S )

HVAC Works VARIABLE REFRIGERANT SYSTEM(VRF SYSTEM) VRF Outdoor Unit Supply, Lifting, Installation, Testing & Commisioning of VRF unit with inverter scroll compressor connectable to multiple indoor units. a) 20.0 HP

f) 10.0 HP for UPS Room (1W+1S)

VRF Indoor Unit Supply of Indoor Units shall be Ductable / Cas1 Sette / Hiwall split type units as specified. The indoor unit shall have independent electronic control valve to control the refrigrant flow rate a) 3.18TR / 1130CFM

b) 2.01TR / 830CFM

c) 1.59TR / 812CFM

d) 1.28TR / 600CFM

e) 1.02TR / 459CFM

Hi-wall Split Unit a) 1.59TR / 530CFM

High static Ductable Unit a) 7.95TR / 2825CFM

b) 6.36TR / 2400CFM

c) 4.55TR / 1624CFM

d) 3.18TR / 1130CFM

Treated Fresh Air Unit Supply,Transport to site, Installation, Testing and Commisioning of Double Skin with Thermal Break Profile of 45+/-2 mm rockwool with density of 40 kg/cu.m and aluminium corner profile with necessary Protection. a) TFA - 470 CFM / 3.8 TR / ESP 25 mm wg for First Floor

b) TFA - 1650 CFM / 13.4 TR / ESP 25 mm wg for Second Floor

c) TFA - 1035 CFM / 8.5 TR / ESP 25 mm wg for Third Floor

d) TFA - 265 CFM / 2.1 TR / ESP 25 mm wg for Fourth Floor

e) TFA - 575 CFM / 4.7 TR / ESP 25 mm wg for Building-02

Refrigerant Piping Supply and Installation of 18G Copper Refrigerant Piping with necessary fittings, Y Joints and headers, insulated with19mm thick elastomeric nitrile rubber insulation and wrapped with polyshield coating between indoor & outdoor units as per specifications a) 28.6 mm dia

b) 25.4 mm dia

c) 22.2 mm dia

d) 19.1 mm dia

e) 15.9 mm dia

f) 12.7 mm dia

g) 9.5 mm dia

h) 6.4 mm dia

Supply, installation, testing and commissioning of Refnet joints

Supply & installation of GI Hot Dip / Powder Coated 16 SWG Cable Tray with 50mm height, covered with G.I.Sheet for copper pipes and cables (for Expsoed tray at external building and terrace) a) 150mm wide

b) 300mm wide

c) 450mm wide

d) 600mm wide

Supply & Laying of High Density PVC drain pipe with necessary supports. a) 25mm dia

b) 32mm dia

c) 40mm dia

Supply and providing of pipeline nitrle rubber insulation for Refrigerant and drain pipe lines. a) 25mm dia

b) 32mm dia

c) 40mm dia

Supply,Laying & Termination of 2C x 1.5sq.mm Transmission cable between IDU to ODU with Necessary supports, screws, etc.

Supply & fixing of GI conduit pipe 15mm B Class complete with all fittings & accessories with Necessary supports, screws ,etc.

Supply & laying of 8SWG Copper wire with double run from panel board to indoor & indoor to outdoor unit for Earthing.

Supply, laying & termination of following cable from Isolator to VRF Outdoor unit and from 10Amps power socket to indoor units with necessary supports and PVC flexible hose, a) 3C x 1.5Sqmm copper Armoured Cu cable

b) 4C x 6Sqmm copper Armoured Cu cable

c) 4C x 10Sqmm copper Armoured Cu cable

d) 4C x 16Sqmm copper Armoured Cu cable

e) 4C x 25Sqmm copper Armoured Cu cable

Supply and installation of Centralized Remote unit ( I tourch manager ) for scheduling, ON / OFF control

Supply & Fixing of Insulated (13mm Nitrile Rubber) Drain drip Tray for ductable unit

Supply and Fixing of Max flow drain pump for ductable unit

Supply and Fixing of Max flow drain pump for Hi wall split unit

Air Distribution System Supply, Fabrication and erection of fabricated ducting made up of GI Sheets of following Gauge thickness c) GI sheets of 22 Gauge thickness up to 751 to 1500mm

d) GI Sheets of 24 Gauge thickness Up to 750mm

Supply and install GI sheet metal Factory Fabricated Round ducting with fittings. bend, coupling. transfer piece, confirming SMACNA standards for connecting flexible duct and spigot damper with necessories fixing arrangements. A) 24 SWG G.I

Supply and providing thermal insulation of 9mm thick vidoflex with Aluminum Foil

Supply and providing acoustic for initial portion of ducting with 12mm thick Fibre Glass Rigid Board covered with Tissue Paper and Aluminum Perforated Sheet.

Supplying and of installation of Underdeck Thermal insulation using Extruded Polystyrene Insulation board with Rigid Closed Cell Chlorofluoro carbons & Hydro chlorofluoro carbons Free, Extruded Polystyrene Insulation Foam Board of desired thickness a) 50mm-U value of 0.58W/m2K

Supply and fixing of extruded aluminum powder coated, Supply and return Air Grilles / Diffusers with Volume Control Damper

Supply and fixing of Duct Mouth Dampers

Supply & Fixing of Insulated Flexible Ducting Factory Fabricated Insulated Flexible duct for connecting from main duct to diffuser box with Grip clamp. The length of the flexible duct shall be around 1.0 to 1.8 mtr a) 300 mm dia

b) 250 mm dia

c) 100 mm dia

Supply & Fixing of GI round spigot damper for flexible duct connection. a) 300 mm dia

b) 250 mm dia

Supply & Fixing of GI round Constant Air Volume Box for flexible duct connection a) 100 mm dia

Supply, installation, testing and commissioning of Factory fabricated Rectangular shape - GI Non-return dampers, 18G GI Frame & 22G blade, Multiple-blade, parallel action gravity balanced, with center-pivoted blades of maximum 75-mm width, with sealed edges, assembled in rattle-free manner with 90-degree stop, steel ball bearings, and axles; and as per specifications.

Supply & fixing - Extruded Aluminimum powder coated Supply/Fresh air grills with necessary GI Screw, bolt, nut & supports. ( colour for the grill to b conifremed by Arch/ PMC team before placing the order) The Grille plenum should be fixed to the false ceiling using 4inch tap (Water proof PE coated fabric Tap withy thick of 0.26mm+/- 10%) to ensure Zero leakage before fixing grilles at false ceiling.

Supply & fixing - Extruded Aluminimum powder coated Return/Exhaust air grills without VCD with necessary GI Screw, bolt, nut & supports. ( colour for the grill to b conifremed by Arch/ PMC team before placing the order)

Supply, installation, testing and commissioning of extruded Aluminium powder coated Fresh air & Exhaust air louver to be installed in external Facade. HVAC vendor to be coordinate with civil vendor for the installation of same & Finishing of same to in civil scope.The color & pattern shall be pre-approved by Architects/Client

Supply, installation, testing and balancing of aluminium powder coated non-vision door transfer grilles as per approved shop drawings and specifications with standard flange size.

Ventilation System Liftwell Pressurization Unit Supplying, installing, testing and commissioning of Axial fans with 25 MM Static pressure as per specifications. Fan shall be Tube axial (AMCA certified) Motors shall be suitable for 415+10% volts, 50 cycles , 3 phase AC supply Capacity - 10000CFM

Supply ,Installation & Commissioning of Double skin type Centrifugal Inline Exhaust fan with suitable Static Pressure for following areas a) Capacity-1950CFM for 3F equipment Room EA Fan

b) Capacity-1500CFM for All Floor Toilet EA Fan

c) Capacity-1450CFM for 2F & 3F equipment Room EA Fan

d) Capacity-1200CFM for 2F equipment Room EA Fan

Supplying, installing, testing and commissioning of direct driven PROPELLER FANS for exhaust air a) Capacity-1000CFM for GF Pump Room EA Fan

b) Capacity-800CFM for GF Electrical Room EA Fan

c) Capacity-750CFM for GF Electrical Room EA Fan

d) Capacity-425CFM for 2F Solids Room EA Fan

e) Capacity-350CFM for GF Equipment Room EA Fan

f) Capacity-300CFM for 2F Sample Preparation Room EA Fan

g) Capacity-125CFM for GF Common Toilet EA Fan

h) Capacity-100CFM for GF Driver & Maintenance & 3F Head Scientist Toilet EA Fan

i) Capacity-200CFM for All Floor Toilet EA Fan

Supplying, installing, testing and commissioning of Circular inlne exhaust fan with 15mm g motor shall be suitable for 220±10% volt single phase 50 cycles AC supply a) Capacity-400CFM for 1F VIP Toilet EA Fan

FIRE PUMPS AND ACCESSORIES STANDBY DIESEL ENGINE PUMP Supply, installation, testing and commissioning of Diesel Engine Driven Main Fire Pump suitable for automatic operation and consisting of following and complete in all respects as required.

MAIN ELECTRICAL DRIVEN FIRE PUMP 1 Set Supply, erection, testing and commissioning of Fire Fighting Application Horizontal Centrifugal Type Pump Rated for 2280 LPM at 70 1 RMTs head with Electrical Motor of 60 HP of 415 volt 3 phase connection

JOCKEY PUMP 1 Set Supply, erection, testing and commissioning of 180 LPM, 70 1 RMTs Head Pressurization Pump with 10HP electrical motor

Supply, Installation, Testing & Commissioning of double flanged Air cushion tank/ pressure vessel of 300mm dia fabricated from 10mm M.S. plate with dished ends from 10mm M.S. plate, outside with one coat of primer and two coats of synthetic enamel paint of approved shade

DIESEL ENGINE AUTO STARTER PANEL Supplying, erection, testing and commissioning of Diesel Engine Pump Main Control Panel & Jockey Pump

Supply, Laying, Testing and Commissioning of the following size a) 12 Core 2.5 Sq.mm PVC Copper Armoured Cable

Electrical Panel Supplying, installation, testing and commissioning of Fire Fighting Electrical Control Panel of cubical construction, floor mounted type fabricated using CRCA sheet

Cables For electrical main panel a) 3.C x 70 sq.mm for main pumps (Al) FS cable

b) 3 core 6 Sqmm. Jockey pumps / Booster Pumps (CU) FS cable

c) 2 core 2.5 sq.mm. armoured Copper cable

CABLE TRAY Supplying and fixing of Cable Tray of following size by using 16SWG GI Hot Dip / Powder Coated Cable tray from wall a) 150mm width and 50mm height

b) 300mm width and 50mm height

EARTH Supplying and fixing of G.I. Earthing strips of 25mm X 6mm thick, strip shall be run on floor / ceiling / walls, from the equipment to the nearest Earth pit with necessary accessories

Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm a) 250 mm Nominal Bore (NB)

b) 200 mm Nominal Bore (NB)

c) 150mm Nominal Bore (NB)

d) 100mm Nominal Bore (NB)

e) 80 mm Nominal Bore (NB)

f) 50 mm Nominal Bore (NB)

g) 25mm Nominal Bore (NB)

Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water a) 250 mm Nominal Bore (NB)

b) 200 mm Nominal Bore (NB)

c) 150 mm Nominal Bore (NB)

d) 100 mm Nominal Bore (NB)

e) 80 mm Nominal Bore (NB)

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor a) 150 mm Nominal Bore (NB)

b) 100 mm Nominal Bore (NB)

Supply, erection, testing and commissioning of cast iron body and gun metal or stainless steel Internal Non-Return Valve of size of 80mm dia to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor

Supplying, installing and commissioning C.I.flanged "Y" type Strainer with SS mesh,suitable adapter flanges, nuts, bolts, gaskets etc. complete. (suction side) PN16 Rating a) 200 mm Nominal Bore (NB)

b) 100 mm Nominal Bore (NB)

Supply, erection, testing and commissioning of Gun Metal Gate Valve of size 50mm dia size including necessary MS flange of table „E‟, gaskets, bolts & nuts

Supply, Installation of Flow 1 RMT (Electronic type) on Test line to measure 150 % of pump flow and suitable to 150 mm dia. (PN20) with fittings of screwed end type.

Test Array Manifold Arrangement for pump1 Set with pressure gauge (1 No.), pressure switch (3 No.) as per specification i) Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve Make: H-GURU / ISI MAKE / EQUIVALENT ii) Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line Indfoss or Donfoss including necessary valves Make: DONFOSS / INDFOSS / ISI MAKE / EQUIVALENT

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure

Supply and installation of hot dip GI puddle flanges, as per IS-1239, Own Make out of 6mm MS Plate, fixed at the RCC walls of the fire tanks & Over head tanks, work includes painting with 2 coats of primer a) 150mm Nominal Bore (NB)

b) 100mm Nominal Bore (NB)

Supply, erection, testing and commissioning of Fire Fighting 4 Way Fire Brigade Inlet with necessary gun metal 63mm dia non return spring shutter arrangements

Supply, erection, testing and commissioning of Fire Fighting 2 Way Fire Brigade Inlet with necessary gun metal 63mm dia non-return spring shutter arrangements

Supply, fabricating , installing structural steel secondary supports & external pipes for fixing all sizes of MS pipes from ceiling / wall with MS Channels as required at site

EXTERNAL HYDRANT Above ground pipe - Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm a) 150mm Nominal Bore (NB)

b) 80mm Nominal Bore (NB)

Under ground pipe - Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm a) 150mm Nominal Bore (NB)

b) 80mm Nominal Bore (NB)

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve

Supply, and fixing in position of Fire Fighting Application Hose of 63mm dia of 15 1 RMTs length binded by copper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901

Supply, and fixing in position of Fire Fighting Application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore.

Supply of Fire Fighting Application MS Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside

Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water a) 150mm Nominal Bore (NB)

Supply, Installation, Testing & Commissioning of NP2 Class Hume Pipe for road crossing a) 200mm Nominal Bore (NB)

b) 300mm Nominal Bore (NB)

Wrapping and coating anti-corrosive treatment for the following under ground MS pipe a) 150mm Nominal Bore (NB)

b) 80mm Nominal Bore (NB)

Providing, fixing pipe supports from columns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods threaded a) 80mm Nominal Bore (NB)

INTERNAL HYDRANT BOOSTER PUMP1 Set Supply, erection, testing and commissioning of fire fighting application monoblock motor pump1 Set of 900 LPM at 40 1 RMTs head to develop 3.5 kg/sq.cm at the heightest and farthest hydrant point to make 30 m water jet at the time of fire fighting emergency

BOOSTER PUMP PANEL Supply, erection, testing and commissioning of Fire Fighting Electrical Control Panel of 15 HP, 415 V, 50 Hz Rating Wall Mounted Type fabricated using CRCA sheet, hinged lockable door, dust and vermin proof

Cable for Terrace Pump Supply and laying of 4 core 10 sq.mm. armoured copper cable for power wiring to the Terrace Pump Motor with runs of 14 SWG TC wire

Above ground pipe - Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm a) 150mm Nominal Bore (NB)

b) 100mm Nominal Bore (NB)

c) 80mm Nominal Bore (NB)

Under ground pipe - Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm a) 100 mm Nominal Bore (NB)

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia

Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water a) 150mm Nominal Bore (NB)

b) 100mm Nominal Bore (NB)

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser,

Wrapping and coating anti-corrosive treatment for the following under ground MS pipe having one coat of anticorrosive metal primer, one layer of asphalt tar tape wound over the MS Pipe as per standard methods as per standard specifications a) 100 mm Nominal Bore (NB)

Providing, fixing pipe supports from columns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods a) 100mm Nominal Bore (NB)

b) 80mm Nominal Bore (NB)

SPRINKLER SYSTEM Above ground pipe - Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm a) 65mm Nominal Bore (NB)

b) 50mm Nominal Bore (NB)

c) 40mm Nominal Bore (NB)

d) 32mm Nominal Bore (NB)

e) 25mm Nominal Bore (NB)

Supply and fixing nominal bore quartized bulb type sprinkler K80 bulb 68 Deg C fast response pendent type including GI collar for each sprinkler bulb, mounted in MS pipe line

Supplying and installing of approved type Rosette Plates (Recessed Type in Two Pieces) for sprinklers below false ceiling area.

Supply, Installing, testing and commissioning of Stainless Steel Corrugated Flexible Braided Pipe (Hose)

Supply, Installation, Testing & Commissioning of standard response Extended Coverage Sidewall Sprinklers of 68 Deg.C.Temp. rating K80 sprinkler

Supply, Installation, Tesing & Commissioning of electrically operated water flow switches (Vane type) a) 100mm Nominal Bore (NB)

b) 80mm Nominal Bore (NB)

Supply, installation, testing and commissioning of inspectors test assembly complete with test valve PN 16 Rating, with all necessary accessories.

Supplying, installing, testing and commissioning of hydraulically operated 150mm dia Sprinkler control valve, with water motor gong bell

Providing, fixing pipe supports from columns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement a) 100mm Nominal Bore (NB)

b) 80mm Nominal Bore (NB)

c) 50mm Nominal Bore (NB)

d) 40mm Nominal Bore (NB)

PORTABLE FIRE EXTINGUISHER Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683

Supply and fixing of Water CO2 Stored Pressure Type 9 litres capacity Fire Extinguisher as per new IS 15683

Supply, Installation, Testing & Commissioning of clean agent fire extinguisher of 4kg.capacity with necessary accessories etc.

Supply, Installation, Testing & Commissioning of FE-36 clean agent Celing mounted fire extinguisher of 5 kg.capacity with necessary accessories etc.

Supply, Installation, Testing & Commissioning of AFF Mechanical Foam type capacity of 9 litre fire extinguisher.

Supply and installation of Fire buckets of 9 ltrs capacity. Stand made of MS Channel and angle to accommodate 4 No of buckets filled with cleaned soft sand. Rate shall be inclusive of red paint as per Fire Codes for buckets and MS Stand.as per specification

SIGNAGES The following descriptive photoluminescent Green or Red color safety signages in different sizes / graphics /colours / texts can be made according to the standards a) RUNNING MAN ARROW DOUBLE SIDE (150X400mm)

b) EXIT (400x150mm)

c) FIRE EXIT (400x150mm)

d) INCASE OF FIRE DONT USE LIFT,USE STAIRCASE (250x300mm)

e) FIRE HYDRANT & HOSE REEL(150x200mm)

f) MANUAL CALL POINT (150X400mm)

g) FIRE EXTINGUISHER (150x400mm)

Supply & Installation of EVACUATION MAP color which needs to be displayed onto a GLASS frame which are Self Glow type. Size should be A2 Size 17" x 22". (samples to be shown before execution) Placed Inside the FCC Room & Each Floor.

Supply & Installation of" Fire Pump Details & Operation Sequence"t should contain the following matter on 3mm thick "Opaque" PVC foam board of computerised cut, PVC non-reflective self adhesive vinyle painted foam board of 3' * 4'

Supply & Installation, in position the signages "FIRE ORDER" it should contain the following matter on 3mm thick "Opaque" PVC foam board of computerised cut, PVC non-reflective self adhesive vinyle painted foam board of 3' * 4'

ELV works Fire Detection & Alarm System Fire Alarm Panel Addressable Fire Alarm Control Panel consists of display board which will have 160 Character Display

Addressable Detectors with base with Binary coded address setting. Dual LED’s for 360° visibility i) Smoke detector Ground Floor

First Floor

Second Floor

Third Floor

Fourth Floor

ii) Multi Sensor - Heat Cum Smoke detector Ground Floor

First Floor

Second Floor

Third Floor

Fourth Floor

DEVICES Fault Isolator Module capable of monitoring shorted loop circuit and automatically restore communications Ground Floor

First Floor

Second Floor

Third Floor

Fourth Floor

Addressable Manual Call Point - Re1 Settable type - with back box with Binary coded address 1 Setting with Status LED for 360° visibility. Ground Floor

First Floor

Second Floor

Third Floor

Fourth Floor

Control Module for Hooter : Supply, Installation, testing and commissioning of Addressable Control Modules for activating hooters with all the mounting accessories complete as required. Ground Floor

First Floor

Second Floor

Third Floor

Fourth Floor

Control Module for Access Controllers System Integration: Supply, Installation, testing and commissioning of Addressable Control Modules for overriding access door command with all the mounting accessories complete as required.

Control Module for PA Integration: Supply, Installation, testing and commissioning of Addressable Control Modules for overriding PA system with all the mounting accessories complete as required. One CM shall provide one activation signals.

Control Module for Lift Integration: Supply, Installation, testing and commissioning of Addressable Control Modules for overriding Lift with all the mounting accessories complete as required. One CM shall provide one activation signals.

Monitor Module- Flow switch monitoring: Supply, Installation, testing and commissioning of Addressable Monitor Modules for Flow switch monitoring with all the mounting accessories complete as required.

NOTIFICATION DEVICES Conventional type Horn wall mounted type rated at 100 dBA @ 1m for Audible announcation.

CABLES, CONDUITS, HUME PIPES & RACEWAYS Cable 2 Core - 1.5 sq.mm

OTHER EQUIPMENTS Supply, Installation, testing and commissioning of DC Regulated Power Supply, 230 to appropriate 24 Volts requirement of Hooters

PUBLIC ADDRESS & VOICE EVACUATION SYSTEM Supply of 9U rack with accessories for switch., all complete and as directed by the departmental officers

System Controller Supply of 8 Zone Voice Management Controller with accessories., all complete and as directed by the departmental officers

Amplifier Supply, installation, testing and commissioning of PA Booster Amplifier 480W

Supply and installation of Speaker Ground Floor

First Floor

Second Floor

Third Floor

Fourth Floor

Conduit Supply and Laying of 20mm PVC RIGID conduit Pipes with ISI conduit pipe Heavy with Accessories

Supply of 5MP IP Bullet / Dome Camera with SD card Support. (For Indoor Application) Ground Floor

First Floor

Second Floor

Third Floor

Fourth Floor

Supply of 5MP IP Bullet / Dome Camera with SD card Support. (For Outdoor Application) etc., all complete and as directed by the departmental officers Ground Floor

NVR & Display Supply of 40-Ch IP NVR Input, resolution up to 12MP, Dual RJ45 port, 4SATA (up to 10TB), 1 HDMI&VGA, 2USB, RAID

Supply, Installation, Testing & Commissioning of 55'' LED Monitors complete with Desktop mount kit

POE SWITCH FXS - 16 Port for IP Extension

CABLE Supply of Cat 6-A, LAN UTP Cable for CCTV etc.,

Supply of Fiber Single Mode Cables 12 Core Armoured

CONDUIT Supply & Laying of 25mm PVC conduit for CCTV etc., all complete and as directed by the departmental officers

Cable tray Supplying and fixing of GI Hot Dip / Powder Coated 16 SWG Cable Tray with Accessories

Supply, Installation, Testing & Commissioning of Hume pipe of 150mm dia with required bends and other accessories as required

Access Control Software Supply, Installation, Testing & Commissioning of Windows Operating System supported Access Control & Attendance Management Software with Accessories

Supply and Installation of Personal Computer with Accessories HDD - 500 GB 4 GB RAM I 5 processor R/W CD drive Monitor - 21"

Biometric reader Supply, Installation, Testing & Commissioning of Biometric type reader for Indoor Application

Door Controller Supply, Installation, Testing & Commissioning of 2 reader interface modules i.e 1 door controller with necessary mounting rack and power supply units & accessories

Locks & Switches for Door Supply, Installation, Testing & Commissioning of Single Leaf EML with door magnetic contact for Indoor Application

Supply, Installation, Testing & Commissioning of Double Leaf EML with door magnetic contact for Indoor Application

Cable & Conduiting Supply, Laying, Termination of 8 core, 0.75 sq.mm, ATC Multi Strand,Shielded, PVC insulated, unarmored, Tinned Copper, , Cable with proper ferrules, lugs and other necessary accessories. For Reader to Controller

Supply, Laying, Termination of 4 core, 0.75 sq.mm, 16 twists per meter, PVC insulated, Unarmored, Tinned Copper, overall shielded, Cable with proper ferrules, lugs and other necessary accessories. For Lock

Supply, Laying, Termination & Testing of Power Cable – 3 Core 1.5 Sq.mm, Unarmored, Copper Cable with overall PVC Insulation (Power socket to be provided near access control panel)

Supply, Laying, Terminating, Testing and Commissioning of ISI Certified ACS Communication Cable

Supply & Laying of 1", 2mm thick, FRLS PVC Conduit with bends, collar, saddles, saddle base and other accessories.

Design, Supply, Installation, Testing, Commissioning towards On-Grid Roof Top Solar PV Power plant as per the following specification System Size-Total Capacity – 50 KW DC Area Required for Installation - 500 SQM of non-Shade free

Lift arrangements Design, Supply, Delivery, Installation,Testing and Commissioning of Goods/Service lift ( 16 Persons capacity/1800kg) MRL, Speed 1.5 m/s with Stainless Steel

Lift arrangements Design, Supply, Delivery, Installation,Testing and Commissioning of Goods/Service lift ( 8 Persons capacity/544kg) MRL, Speed 1.5 m/s with Stainless Steel

Please Enable Macros to View BoQ information