Special Repair of PHC at BHAGAL in Kaithal District

Amount

Base course of floors consisting of 100 mm thick cement concrete 1:8:16 and 100 mm sand or stone filling. (HSR 14.1)

Conglomerate floor 50 mm thick cement concrete topping 1:2:4 (HSR 14.10)

Plastering on walls 12 mm thick cement plaster 1:4 (HSR 15.5)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.58).

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (b)].

Painting two coats with synthetic enamel paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. [HSR 16.5].

Finishing walls with exterior decorative cement based paints such as snowcem, Robbiacem etc. on old work, one coat to give an even shade. (HSR 16.62)

Factory manufactured solid flush door shutters, with block board core as per I.S.No.1659- 1969 bonded with water proof type phenol formaldehyde synthetic resin,hotpressesd, conforming to I.S.2202 part I and II, fixed in position,including iron hinges,screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above,but including labour for fixing the same in position)- (HSR 17.93a) iii) - note (i) of HSR 17.18)

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the engineer-in-charge). (HSR 30.75) Bib cock

Bib cock long body

Providing and fixing in position C.P brass stop cocks (as approved by the Engineer-in-Charge) a) 15mm stop cock (HSR 30.76a) i) Stop cock male and female end.

ii) Concealed stop cock with flange

Providing and fixing in position best indian make flexible tube connection b) C.P brass i) 15mmx300mm. (HSR 30.82b)

Providing and fixing in position best Indian make European type water closet suite with concealed 'P or 'S trap with or without vent (as approved by the Engineer-in-charge) and all other necessary fitting as fully described in item no. 30.3 above. (i) white (HSR 30.6(i)

Providing and fixing 15 liters capacity low level vitreous china ware cistern complete with flush bend all other necessary fitting instead of C.I high level cistern complete with fitting. (i) white (HSR 30.12(i)

Providing and fixing best indian make plastic hygenic seat with lid complete instead of hollow black or white plastic seat and lid (HSR 30.13) (i) white plastic seat (solid) (HSR 30.13(i)

Providing & fixing in position best Indian make white lavatory suites (with full anti splash rim in vitreous chinaware and all other necessary fittings as fully described in item no. 30.41 above (iii) 610mmx510mm with one No. tap (HSR 30.42(iii)

Providing and fixing in position 32mm dia G.I waste pipe embedded in wall or lead waste pipe (weighing 3.47 kg. per metre and 2.8 mm thick) upto floor level including cost of wipped solder joint etc. complete (as required by the Engineer-in-charge) (HSR 30.48)

Providing and fixing in position best Indian make vitreous chinaware sinks with complete fittings as fully described in item no. 30.51. White (a) Size 600 mm x 450 mm x 200 mm (HSR 30.52a)

Providing and fixing HCI floor traps ISI marked of the self cleaning design with C.P brass hinged grating with frame with or without vent arm and including cement concrete 1:2:4 under and around the floor trap where required upto floor level complete in all respects including cutting and making good the walls and floors etc. minimum depth of water should be 150 mm with a minimum seal of 50mm b) With 75mm I/d outlet. (HSR 30.89b)

Providing and fixing HDPE water storage tanks of sintex, Diplast, O.K. supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing Iin position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction to the Engineer. 1000 Ltr. Cap. (HSR 30.119)

Providing and fixing GI pipes complete with GI fittings and clamps i/c cutting and making good the walls (DSR 18.10) 15mmq

Providing and fixing GI unions in GI pipes i/c cutting and threading the pipe and making long screws etc. complete (DSR 18.46) 15mm

Providing and fixing Gun Metal Gate valve with CI wheel of approved qualtity screwed end (DSR 18.17) 15mm

The Sismor co op L and C Society Ltd

The Friends Co op L and C Society Ltd. Kaithal