Construction of Toilet Block with Dressing Room in Sports Stadium at Sohna in Gurugram Distt. (RECALL)

Amount

Earth work in excavation in foundations, trenches, etc. in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres as per HSR 6.6

Cement concrete 1 : 4 : 8 with stone aggregate 20 mm Nominal size in foundation and plinth. As per HSR 10.38

First class brick work laid in cement, stone dust (from crusher) mortar 1:6 in foundation and plinth. As per HSR 11.2

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinthlevel. As per HSR 11.7

Cement concrete 1:1 1.5:3 with stone aggregate 20 mm nominal size for reinforced concrete stone aggregate, complete in all respects as per HSR 10.86+10.95a

Cement concrete 1:1 1.5:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centering and shuttering , laid in position, complete in all respects as per HSR 10.82+10.95a

Steel reinforcement TMT bars FE-500 EQR/FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including straightening, bending, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights /depths/storeys/basements etc. (HSR 18.22) NOTE:- Reinforcement shall be measured in length including hocks, if any, separately for different diameters as actually used in work, excluding overlaps, Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement.

10mm thick cement plaster 1:3 (HSR: 15.2)

12mm thick plaster as per HSR 15.7

Earth filling under floor with combined lead 5km laying in layer watering and compaction complete (NS).

Conglomerate floor 40 mm thick cement concrete 1:2:4 on 100 mm cement concrete 1:8:16 and 100 mm sand or stone filling as per HSR 14.12

Providing & fixing ceramic tiles/ anty skid tile of size 400mm X 400mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles Note:- Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO,KAJARIA,SOMANI,ORIENT Bell, JONSONS , RAK & SIMPOLO(HSR 14.91) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material

Providing & fixing Ist quality ceramic glazed wall tilesconfirming to IS 15622 (thickness to be specified by manufacturer)of approved make in all colors,shade except burgundy,bottlegreen,black of any size as approved by engineer-In Charge in skirting ,risers of steps and dados over12mm thick bed of cement mortor 1:3 coarse and jointed with grey cement slurry,including pointing in white cement mixed with pigment to match the shade complete. Size of ceramic Glazed tiles 300mm X 450mm(HSR 14.92 b) Note:- Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO,KAJARIA,SOMANI,ORIENT Bell, JONSONS , RAK & SIMPOLO Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material

Providing and fixing Aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS;733 and IS;1285 fixed with raw plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom, and sides with required neoprene felt etc. aluminum sections shall be smooth, rust free straight mitered and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/paneling C.P brass/stainless steel screws. All complete. Fixed portion (Anodized Aluminum transparent or dyed to required shade according shade according to IS;1868, minimum anodic coating of grade AC 15) HSR 17.95

Providing and fixing 12 mm thick pre-laminated particle board flat pressed three layer or graded wood particle board conforming to IS;12823 grade 1 type II in paneling fixed in aluminum doors. Windows shutters and partition frames with c.p brass/stainless steel screws etc. complete. Pre-laminated particle board with decorative lamination on both sides. HSR 17.97b

Providing Aluminum jail of thickness 7mm thick with openings-75 mm X 75mm of including anodizing and fixing in frame with cost of screws etc. complete. HSR 17.100

Providing fixing Aluminum round shape handic of cuter dia 100 mm with screws etc. complete. Anodized (AC-15) Aluminum HSR 17.102 (i)

Providing fixing aluminum casement windows fastener of required length for aluminum windows with necessary screws etc. complete Anodized (AC-15) Aluminum. HSR 17.101 (i)

Cost of aluminium fitting cokmplte for doors and windows, such as tower bolts, handles, etc., and screws for these fittings (excluding sliding bolt)- for single lead shutter(HSR; 17.72) (a)

Providing and fixing sliding bolt with nuts and screws etc. complete- brass size 250 mm x 16 mm HSR 17.83 (a) ii

Providing and applying tow coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete (J.K/Birla make) HSR 16.81

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. HSR 16.58

Terracing consisting of tiles 22.86 cm X 11.43 Cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg per sqm on top of R.C.C slab including grouting with cement sand mortar 1:3 and top surface to be left clean etcHSr 13.13

Cement concrete 1:2:4 gola 10 cm X 10 cm quardrant along junction of roof with parapet wall finished smooth, where specially specified. HSR 13.64

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE A RANGE OF THREE URINALS FLAT BACK OR ANGULAR LIPPED FRONT IN VITREOUS CHINA-WARE WITH 10 LITRES CAPACITY BEST INDIAN MAKE C.I. AUTOMATIC FLUSHING CISTERN WITH FITTINGS AND FLUSH PIPE ETC., COMPLETE AS FULLY DESCRIBED ITEM NO. 30.19 ABVOE (HSR 30.21)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT WITH NON-CONCEALED ‘P’ OR ‘S’ TRAP with or without vent and all other necessary Fittings as fully described in item no. 30.3 above. White HSR 30.4 i

PROVIDING AND FIXING IN POSITION INDIAN MAKE (ORDINARY) LAVATORY SUITES Consisting of Lavatory in VITREOUS CHINAWARE size as given Below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary; R.S or C.I BRACKETS for building into wall including Painting; 32 mm C.P BRASS WASTER WITH C.P brass chain and rubber plug; 15 mm C.P BRASS SCREW DOWN PILLAR TAP WITH Jamnuts or couplings best design ( as approved by the Engineer- In-charge)HSR 30.41 White (iii)

Providing and fixing in position 15 mm i/d C.P brass bib Cocks of best quality (as required by Engineer-in-charge) Bib cock long body as per HSR 30.75 a

Providing and fixing in position C.P brass stop cocks (as Approved by the Engineer-in-charge) 15 MM STOP COCK Stop cock male and female end (HSR 30.76) (a) (i)

Looking glass and mirror

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE TOWEL RAILS FIXED in with rawlslugs embedded in walls with C.P brass screws. Complete in all respect INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. C.P brass two swivel towel rail 400 mm long. HSR 30.68 d

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P brass screws and complete in all respects including cutting and making good the wells etcs. CP BRASS Soap dish 160 mm HSR 30.70 a (i)

Providing and fixing 15 mm C.P brass Laboratory cock swan neck of best quality (to the approval of the Engineer-in-charge) Two Way HSR 30.78b

CONSTRUCTING BRICK MASONRY INSPECTION CHAMBER SIZES AS GIVEN BELOW UPTO 0.60 METRE AVERAGE DEPTH in cement Mortar 1:5 LIME CONCRETE with 40 percent lime mortar 2:3 in foundation Cement mortar 1:2:4 BENCHING 12 mm THICK CEMENT PLASTER 1:2 with a floating Size 450 mm x 600 mm inside (with 455 mm x 610 mm cover and frame light duty single seal pattern I weighing 38 kg with C.C.topping ) HSR 29.84 b

Providing & fixing PVC Rain water pipe 6 Kg Pressure of ISI Mark in cement mortor during masonery work. 100MM dia PVC pipe 6Kg. Pressure HSR 13.89 a

Providing & fixing PVC Bend ISI Mark 100MM dia PVC pipe 6Kg. Pressure HSR 13.90 a

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 15 mm dia nominal bore(DSR 18.10.1) Make:- UNIK, TATA, ZOLOTO.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 20 mm dia nominal bore(DSR 18.10.2) Make:- UNIK, TATA, ZOLOTO.

Providing and fixing HDPE water storage tanks of sintex, Diplast, O.K. supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing Iin position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction to the Engineer.(HSR-30.119) 1000 Ltr. Cap.

CUTTING HOLES UPTO 23 CM SQUARE THROUGH BRICK WORK IN MUD WALLS FOR PIPES AND MAKING GOOD INCLUDING REPOINTING REPLASTERING AND FINISHING according to existing finish where required. per HSR 28.23 (a) 11.43 cm wall

(b) 22.86 cm wall Note:- In Case of any difference in the DNIT & Nomenclature of any of HSR Items of Civil, PH Work Depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable

Shahid Ahmed