SPECIAL REPAIR OF DISTRIBUTION PIPE LINES, DOOR / WINDOW, SANITARY WORK AT BLDG NO 47 INCLUDING MINOR WORK AT SUNJUWAN UNDER GE JAMMU

Amount

B/R Portion: - Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m deep for foundation etc and getting out in any type of soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm as in soft / loose soil complete all as specified and as directed.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

Dismantling floor, hearth or wall tiling, kitchen slab including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) not exceeding 1.5 Sqm each, including cutting holes for taking out holdfast or dismantling brick works (holes cut and any other damage to jambs, walls for taking out holdfast shall be finished identical to existing finish (without any extra cost to govt) and removing from site complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhat or frame with shutter without taking off shutter from the frame exceeding 1.5 Sqm and not exceeding 4 Sqm each and removing from site complete all as specified and as directed.

Demolition of brick work or stone / boulder masonry, built in lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Material and labour for brickwork with subclass 'B' bricks, straight or curved on plan exceeding 6m means radius built in CM (1:4) complete all as specified and as directed.

Material and labour non-skid / mat finish ceramic joint free tiles 7 to 8 mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

Material and labour glazed ceramic coloured tiles, (premier quality), of size 300mm x 450 mm x 7 to 8 mm to thick joint free on vertical surfaces such as skirting, dados and risers to steps etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including 10 mm thick rendering in CM (1:4) all as specified and directed. Note: - Design, shape and pattern of fixing of tiles complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including racking out joints, hacking for key, scrubbing down with water etc and removing unserviceable material outside cantt area complete all as specified and directed.

Material and labour for 15 mm thick cement plaster in CM (1:4) on external wall of external surfaces finished even and smooth using water proofing compound as per manufacturer's instructions complete all as specified and directed. Note: - Water proofing compound shall be measured separately.

Material and labour for 10 mm thick cement plaster in CM (1:6) on internal wall of internal surfaces complete all as specified and as directed.

Material and labour for 10 mm thick plaster on ceiling in cement mortar (1:3) finished even and smooth without using extra cement complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and as directed.

Taking down Gl tubing of 15 mm dia and connection including cleaning complete all as specified and directed.

Supply and fixing 15 mm dia galvanized pipes 'medium grade' with all fittings and fixed complete to wall and ceiling or laid in floor complete all as specified and directed.

Material and labour applying three coats of white wash on ceiling including preparation of newly plastered surface complete all as specified and directed.

Material and labour including preparation of newly plastered surfaces and applying two coats of cement based paint over a coat of primer complete all as specified and directed.

Material and labour for preparation of old decorated surfaces of walls, soffits / facia of chajja / roof slab etc and applying one coat of cement based paint complete all as specified and directed.

Material and labour for preparation and applying two coats of white wash on ceiling including preparation of old plastered surfaces complete all as specified and as directed.

Material and labour for preparation of new surface of wall and applying two coats of oil bound distemper white or tinted including 1 mm thick wall care putty complete all as specified and directed.

Complete removal of existing treatment of old decorated surfaces of wall and applying two coats of distemper oil emulsion white or tinted including 1 mm thick wall care putty complete all as specified and directed.

Preparation / scrapping the existing surfaces of wall including cornices, making good holes with chalk whiting, filling cracks etc and applying one coat of white wash on old prepared surface of walls complete all as specified and directed.

Material and labour for applying two coats of wheather proof paint exterior grade over one coat of wall care putty including all scaffolding arrangement up to four storeyed building complete all as specified and directed.

Taking down door and refixing shutters after making necessary repair of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed. Note: - Builder's hardware used in repairs shall be measured separately.

Supply and fixing factory made pressed steel frames of size 105 x 60 mm made out of PBI sheet 1.25mm thick for doors with one or more rebates including fixing lugs, hinge, lock strike plate etc complete including bottom of each chowkhat to be welded with 02 no's 25 x 25 x 3 mm angle iron projecting 10cm one either side including one shop coat of red oxide chrome primer and including PCC (1:3:6) type C-0 in back filling of chowkhats and tarring back of chowkhat and holdfasts complete all as specified and as directed.

Supply and fixing factory made pressed steel frames of size 125 x 60 mm made out of PBI sheet 1.25mm thick for doors with one or more rebates including fixing lugs, hinge, lock strike plate etc complete including bottom of each chowkhat to be welded with 02 no's 25 x 25 x 3 mm angle iron projecting 10cm one either side including one shop coat of red oxide chrome primer and including PCC (1:3:6) type C-0 in back filling of chowkats and tarring back of chowkhat and holdfasts complete all as specified and directed.

Supply and fixing 35mm thick factory made second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part - l section 18, clause 8.24 (a) complete all as specified and directed.

Supply and fixing factory made, second class hard wood, plain framed panelled shutters (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial) veneering on both sides, the size of rail and stile as per IS : 1003 (Part-I) kiln seasoned chemically pressure treated 35mm thick complete all as specified and directed by Engineer-in-Charge.

Supply and fixing solid PVC door frame of size 50mm x 47mm, made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting frame work made out of mild steel tubes for top and bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap inserts for top rail and bottom rail panelling of plain colour PVC sheet to be fitted in the mild steel frame welded / sealed to the stiles and rail with suitable PVC sheets beading and jointed together with solvent cement, supply and fixing in frame at site as per specification and drawing in SSR 2020 part-Il complete all as specified and directed.

Supply and fixing 100mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinges complete all as specified and directed.

Supply and fixing 200mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

Supply and fixing Aluminium alloy, anodised, sliding door bolt of size 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolt of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

Supply and fixing box type steel windows comprised of tubular frame and shutter made out of 1.25 mm thick mild steel sheet tube factory made with double side shutter wire gauzed shutter and glass glazed shuter (wire cloth and glass panes will be measured and paid separately) with side hung shutters with mild steel handles and mild steel peg stay dovetailed or welded including 02 No's mild steel tower bolts 150 mm long for each leaf and 08 mm square bar grill / guard bars at spacing as shown on drawing welded mild steel flat iron frame work, including other fittings, hinges, mild steel handles, tarred hold fasts, PCC blocks for hold fasts etc complete all as specified and directed.

Supply and fixing box type steel ventilator comprised of tubular frame and shutters made out of 1.25 mm thick mild steel sheet tube factory made with fixed type wire gauged shutter (wire cloth and glass panes will be measured and paid separately) with side hung shuters with mild steel handles and mild steel peg stay dovetailed or welded including 02 No's mild steel tower bolts 150 mm long for each leaf and 08 mm square bar grill / guard bars at spacing as shown on drawing welded mild steel flat iron frame work, including other fittings, hinges, mild steel handles, tarred hold fasts, PCC blocks for hold fast etc complete all as specified and directed.

Supply and fixing galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with rails / wooden beading / steeI staple complete all as specified and directed.

Supply and fixing in repair mild steel powder coated colour decorative type drapery rod of 20mm dia approved pattern and design including decorative knobs (02 x No for each opening) and powder coated mild steel flat iron brackets fixed with steel screws and PVC rawl plugs / grip complete all as specified and directed.

Supply and fixing 3mm thick sheet glass ordinary quality and glazing with oil putty in square pane complete all as specified and directed.

Description all as per Ser item No 40.00 here-in-before but figured, pin head type and glazing with oil putty or wooden beads, in squares each pane complete all as specified and directed.

Supply and fixing in repair vitreous china squatting pan 'Orissa' pattern size 580 x 440mm white, with integral foot rest 'P' or 'S' trap, front or back inlet inicluding connectlon to trap and to flushing pipe, anti-syphonage pipe etc. complete making good to floor as existing all as specified and directed by Engineer-in-Charge.

Supply and fixing 20mm dia stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed..

Supply and fixing in repairs vitreous china wash hand basin white of size 580 x 400mm with PVC connection (15 x 450) mm long with PTMT nuts and PVC washer and including cutting for pinning in ends, brackets and provision of Gl waste pipe 32mm (light grade) of adequate size and length brass chromium plated waste coupling 32 mm dia, cast copper alloy chromium plated angle valve 15 mm dia bore chromium plated pillar tap fixing complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 10 litre capacity low level flushing cistern, with inlet float valve, moulded from virgin poly propylene single flush including provision of 32mm dia PVC flush pipe and making connections, ISI marked complete all as specified and directed.

Supply and fixing in repair PVC connections 15mm size with PTMT nuts of length 600 mm complete all as specified and directed.

Supply and fixing in repair sheet glass shelf assembly consisting of guard rails and bracket 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long with aluminium alloy complete all as specified and directed.

Supply and fixing in repair tubular towel rail, 20mm dia, 'D' type and 60cm long between flange of brass chromium plated complete all as specified and directed.

Supply and fixing in repair chromium plated grating doom 100mm dia including embedding in tiles with white cement complete all as specified and directed.

Supply and fixing in repair stop valves cast copper alloy 15 mm dia; fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with capstan handle, screwed both ends for iron pipes or for unions and fixed complete all as specified and directed.

Supply and fixing in repair bib tap cast copper alloy with crutch or butterfly handle, chromium plated fancy type screwed for iron pipe, suitable for 15 mm bore complete all as specified and directed.

Supply and fixing in repair 15mm bore pillar cocks chromium plated brass with capstan head screwed down high pressure complete all as specified and directed.

Material and labour for applying two coats of synthetic enamel paint on wooden surfaces over one coat of pink primer including preparation of new surface over 10cm width or girth complete all as specified and as directed.

Material and labour for preparation of old wooden or wood based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.

Material and labour granite 15 to 18 mm thick (Pure black) (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) by using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed in CM (1:4) edges of slab to be rounded from all side (including cutting and polishing) complete all as specified and directed.

Supply and fixing in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm to 420mm bowl size 410 x 330mm x 160mm complete all as specified and directed.

Supply and fixing in repairs stainless steel plate rack 1.25mm thick of size 900 x 775 x 250mm including angle iron brackets and taking down of 19mm thick particle board shelf and removal from site complete all as specified and directed.

Dismantling water tanks complete all as specified and directed.

Supply and fixing 500 litre PVC rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in any type of soil complete all as specified and directed.

Material and labour for 100mm thick PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in flooring or sub base complete all as specified and directed.

Material and labour for 15mm thick screed bed or bedding layer for laying floor finishes in cement mortar (1:6) complete all as specified and directed.

Material and labour for chequered cement concrete tiles 20cm x 20cm x 25mm / 30cm x 30cm x 25mm thick, pre-polished set, jointed and pointed in neat cement slurry with grey / colour cement and pigment in floor complete all as specified and directed.

Material and labour for non skid ceramic black colour joint free 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 72 Sqm in floors / walls etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

Material and labour for providing and fixing stainless steel (grade 304) ailing made of hollow tubes, channels, plates etc, including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete including fixing the railing with necessary accessories and stainless steel dish fasteners, stainless steel bolts etc of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

Meterial and labour for providing and fixing stainless steel chain to post on granite platform complete all as specified and directed.

Material and labour for RCC (1:2:4) nominal mix with (using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Formwork to sides and soffits of rough finish surfaces of concrete floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams fair finished surfaces of concrete etc complete all as specified and directed.

Material and labour mild steel TMT bars 10mm and above, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in reinforcement complete all as specified and as directed.

Material and labour 5mm dia and over upto 10mm dia, cut to length, bent to shape required, including cranking, bending, spirally for hooking for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Material and labour PCC (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in foundation, filing and mass concrete complete all as specified and directed.

Material and labour for preparation of new steel surfaces of any description over 10cm in width or girth not otherwise described and applying two coats of synthetci enamel paint complete all as specified and as directed.

Supply and fixing in repair angle valves chromium plated screwed both ends for 15mm bore of iron pipe or for union and fixed complete all as specified and as directed.

E/M portion: - Supply and fixing cast iron rising sluice valve both end flanged class PN 1.6 conforming to IS-14846-2000 with iron wheel head and brass spindle including necessary joint with nuts bolt, washer, rubber or fibre board gasket, etc and testing complete all as specified and directed including taking down old one complete suitable for the 150mm bore of pipes. Note: - Rate quoted by the contractor inclusive of necessary arrangement required for fixing of the item.

Supply and fixing cast iron rising sluice valve both end flanged class PN 1.6 conforming to IS-14846-2000 with iron wheel head and brass spindle including necessary joint with nuts bolt, washer, rubber or fiber board gasket, etc and testing complete all as specified and directed including taking down old one complete suitable for the 200mm bore of pipes Note :- Rate quoted by the contractor inclusive of necessary arrangement required for fixing of the item

Supply and fixing cast iron non return valve both end flanged and fixed to the existing pipe line including joint with nut bolt, washers, rubber or fiber board gasket, etc testing complete all as specified and directed including taking down old one complete suitable for the 150mm bore of pipes.

Supply and fixing cast iron double orifice air release valve ISI marked IS : 14845 type DS-2 in PN 1.0 flanged end with provision for inbuilt isolating valve to the existing pipe line including joint with necessary fittings as required at site, testing complete all as specified and directed including taking down old one complete suitable for the 50mm bore of pipes.

Supply and fixing cast iron double orifice air release valve ISI marked IS 14845 type DS2 in PN 1.0 flanged end with provision for inbuilt isolating valve to the existing pipe line including joint with necessary fittings as required at site, testing complete all as specified and directed including taking down old one complete suitable for the 100mm bore of pipes.

Taking up or down existing leakage GI pipe line in position of any length for repair / rectification of leakage, replacement of unserviceable fittings and welding work as per site from trenches / walls, floors, ceiling etc and other restore the water supply for the 100mm bore of pipe complete all as specified and directed.

Taking up or down existing leakage GI pipe line in position of any length for repair / rectification of leakage, replacement of unserviceable fittings and welding work as per site from trenches / walls, floors, ceiling etc and other restore the water supply for the 80mm bore of pipe complete all as specified and directed.

Taking up or down existing leakage GI pipe line in position of any length for repair/rectification of leakage, replacement of unserviceable fittings and welding work as per site from trenches / walls, floors, ceiling etc and other restore the water supply for the 50mm bore of pipe complete all as specified and directed.

Taking up or down existing leakage GI pipe line in position of any length for repair/rectification of leakage, replacement of unserviceable fittings and welding work as per site from trenches / walls, floors, ceiling etc and other restore the water supply for the 40mm bore of pipe complete all as specified and directed.

Taking up or down existing leakage GI pipe line in position of any length for repair/rectification of leakage, replacement of unserviceable fittings and welding work as per site from trenches / walls, floors, ceiling etc and other restore the water supply for the 32mm bore of pipe complete all as specified and directed.

Taking up or down existing leakage GI pipe line in position of any length for repair/rectification of leakage, replacement of unserviceable fittings and welding work as per site from trenches / walls, floors, ceiling etc and other restore the water supply for the 25mm bore of pipe complete all as specified and directed.

Taking up or down existing leakage GI pipe line in position of any length for repair/rectification of leakage, replacement of unserviceable fittings and welding work as per site from trenches / walls, floors, ceiling etc and other restore the water supply for the 20mm bore of pipe complete all as specified and directed.

Taking up or down existing leakage GI pipe line in position of any length for repair/rectification of leakage, replacement of unserviceable fittings and welding work as per site from trenches / walls, floors, ceiling etc and other restore the water supply for the 15mm bore of pipe complete all as specified and directed.

Supply and fixing galvanised iron pipe medium grade laid in trenches with all fittings such as tee, bends, sockets, union etc all as required for the 100mm bore of pipe complete all as specified and directed.

Supply and fixing galvanised iron pipe medium grade laid in trenches with all fittings such as tee, bends, sockets, union etc all as required for the 80mm bore of pipe complete all as specified and directed.

Supply and fixing galvanised iron pipe medium grade laid in trenches with all fittings such as tee, bends, sockets, union etc all as required for the 50mm bore of pipe complete all as specified and directed.

Supply and fixing galvanised iron pipe medium grade laid in trenches with all fittings such as tee, bends, sockets, union etc all as required for the 40mm bore of pipe complete all as specified and directed.

Supply and fixing galvanised iron pipe medium grade laid in trenches with all fittings such as tee, bends, sockets, union etc all as required for the 32mm bore of pipe complete all as specified and directed.

Supply and fixing galvanised iron pipe medium grade laid in trenches with all fittings such as tee, bends, sockets, union etc all as required for the 25mm bore of pipe complete all as specified and directed.

Supply and fixing galvanised iron pipe medium grade laid in trenches with all fittings such as tee, bends, sockets, union etc all as required for the 20mm bore of pipe complete all as specified and directed.

Supply and fixing in galvanised iron pipe medium grade with all fittings such as tee, bends, sockets, union etc and fixed complete to walls and ceiling or laid in floors for the 40mm bore of pipe complete all as specified and directed.

Supply and fixing in galavnised iron pipe medium grade with all fittings such as tee, bends, sockets, union etc and fixed complete to walls and ceiling or laid in floors for the 32mm bore of pipe complete all as specified and directed.

Supply and fixing in galvanised iron pipe medium grade with all fittings such as tee, bends, sockets, union etc and fixed complete to walls and ceiling or laid in floors for the 25mm bore of pipe complete all as specified and directed.

Supply and fixing in galvanised iron pipe medium grade with all fittings such as tee, bends, sockets, union etc and fixed complete to walls and ceiling or laid in floors for the 20mm bore of pipe complete all as specified and directed.

Supply and fixing in galvanised iron pipe medium grade with all fittings such as tee, bends, sockets, union etc and fixed complete to walls and ceiling or laid in floors for the 15mm bore of pipe complete all as specified and directed.

Material and labour for gun metal gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 50 mm bore and fixed complete in existing position including taking down old one complete all as specified and directed.

Material and labour for gun metal gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 40 mm bore and fixed complete in existing position including taking down old one complete all as specified and directed.

Material and labour for gun metal gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 25 mm bore and fixed complete in existing position including taking down old one complete all as specified and directed.

Material and labour for gun metal gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 20 mm bore and fixed complete in existing position including taking down old one complete all as specified and directed.

Material and labour for gun metal gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 15 mm bore and fixed complete in existing position including taking down old one complete all as specified and directed.

Supply, lay, joint and fix and test including replacement of 150 mm dia bore centrifugally cast (Spun) DI pipe with spigot socket ends K 7 Class ISI marked confirming to IS 8329- 2000 with push on joint rubber gasket Tyton joint with cement mortar lining inside and metallic zinc coating with finishing layer bituminous paint on outside the pipe complete all as specified and directed. Note: - (i) The rate of jointing material is inclusive in the item. (ii) DI fittings and earthwork will be measured and paid separately. (iii) DI pipes shall be ISI marked with IS : 8329 of 2000 and the rates of testing also inclusive in item. (iv) No separate payment for cutting of pipes will be given. (v) Cost of all above elements shall be deemed to be included in the quoted rates of above items.

Supply, lay, joint and fix and test including replacement of 100 mm dia bore centrifugally cast (Spun) DI pipe with spigot socket ends K 7 Class ISI marked confirming to IS 8329- 2000 with push on joint rubber gasket Tyton joint with cement mortar lining inside and metallic zinc coating with finishing layer bituminous paint on outside the pipe complete all as specified and directed. Notes: - (i) The rate of jointing material is inclusive in the item. (ii) DI fittings and earthwork will be measured and paid separately. (iii) DI pipes shall be ISI marked with IS : 8329 of 2000 and the rates of testing also inclusive in item. (iv) No separate payment for cutting of pipes will be given. (v) Cost of all above elements shall be deemed to be included in the quoted rates of above items.

Supply, fixing, testing including replacement of ductile iron fittings such as bends (any type radius and angle) tapers any type (straight, bend, increasing, decreasing or double socket etc) Tee pieces single branch "Y" junction double branch, cross (all sockets or socket and spigot) collars, tail pieces with one end flanged (integrally cast) and one end socket, spigot caps and plugs suitable for 100 to 150 mm bore ductile pressure pipes of K-7 classification and push on flexible rubber gasket joints complete all as specified and directed. Note: - (i) DI fittings shall be of same make as of DI pipes or of make as recommended by manufacturers. (ii) The weight of the fittings shall be measured and paid as given in relevant IS or actually provided which ever is less. (iii) All fittings shall bear relevent IS stamping marking. (iv) Excavation and earth work shall be measured and paid for separately. (v) Cost of the joints and jointing materials shall be deemed to be included in the relevant items of DI pipes here-in-before.

Taking up CI / DI water mains (including all fittings) of dia 100-150 mm with spigot and socket ends and lead joints including burning out joints or flanged ends including disconnecting pipes and fittings complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of CI / DI specials for spigot and socketed CI / DI pipes 150 mm dia, such as bends (any type, radius and angle) tapers any type (straight bends, increasing, decreasing or double socket etc) Tee pieces single branch "Y" junction double branch, cross (all sockets or socket and spigot) collars caps and plugs etc. complete all as specified and as directed.

Supply and fixing in replacement of CI / DI specials for spigot and socketed CI / DI pipes 150 mm dia, such as connecting pieces one end flanged and other socket or spigot and bell mouth pieces one end flanged other end tapering as bell mouth complete all as specified and directed by Engineer-in-Charge.

Material and labour in repair of construction of brick masonary valve pit chamber of 1050 x 1050 x 1050 mm sizes (internal dimensions) with mild steel sheet cover 6 mm thick and angle iron 40 x 40 x 6 mm frame duly painted with two coats of synthetic enamel paint over one coat of red oxide primer including locking arrangement, necessary earth work etc complete all as specified and directed.

Material and labour in repair of construction of brick masonary valve pit chamber of 900 x 900 x 900 mm sizes (internal dimensions) with mild steel sheet cover 6 mm thick and angle iron 40 x 40 x 6 mm frame duly painted with two coats of synthetic enamel paint over one coat of red oxide primer including locking arrangement, necessary earth work etc complete all as specified and directed.

Material and labour in repair of construction of brick masonary valve pit chamber of 600 x 600 x 600 mm sizes (internal dimensions) with mild steel sheet cover 6 mm thick and angle iron 40 x 40 x 6 mm frame duly painted with two coats of synthetic enamel paint over one coat of red oxide primer including locking arrangement, necessary earth work etc complete all as specified and directed.

Material and labour for road cutting, PCC hard standing as per site requirement including excavation for laying of GI pipe and making good the disturbed surfaces all as per existing surface complete all as specified and directed.

Material and labour of galvanised iron pipe light grade 40 mm bore for cable protection as a guard pipe complete all as specified and directed.

Supply and laying well burnt old size sub class 'B' bricks laid flat with width equal to length of brick perpendicular to the direction of cable, adjacent / abutting each other complete all as specified and as directed by Engineer-in-Charge in trenches over the cable for protection complete all as specified and directed.

Supplying and laying in trenches clear sand for cushioning under ground cable 8 cm below and 15 cm above complete in level complete all as specified and directed.

Material and labour for PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in coping of poles and similar work including necessary form work and fair finish to exposed surfaces without using extra cement complete all as specified and directed.

Supply and fixing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 Sqmm, 4 core complete all as specified and directed by Engineer-in-Charge. Note: - Wherever cable fixing / connection, suitable thimble should be used as per site situation.

Supply and fix outdoor / indoor end termination joint heat shrinkable 1.1 KV grade cable complete with jointing material (Epoxy based) and accessories suitable for 3½ or 4 core XLPE armoured aluminium conductor cable of size 25 to 50 Sqmm complete all as specified and directed.

Supply and fix LED garden light 10 watt complete all as specified and directed.

NOTE NO 1: - Samples of materials as approved will be kept in GE's sample room. NOTE NO 2: - All fittings and fixtures mentioned above will be fixed to the satisfaction of Engr-in-Charge and GE. NOTE NO 3: - All plumbing works shall be laid or fixed as to be completely air tight or water tight as specified and Contractor will furnish its certificates towards air / water tight before completion of work under the Contract. NOTE NO 4: - Warranty certificate to the Engineer-in-Charge where ever applicable shall be submitted by the Contractor at the time of fittings.

M/S Sukhmani Construction Co.

GENESIS INDIA

M/S TRIKUTA BUILDERS

Bidder Name

M/S VED PAUL MAHAJAN

M/S TRIKUTA BUILDERS

M/S Sukhmani Construction Co.

GENESIS INDIA