REPAIR AND MAINT OF PLASTERING, TILING, PLUMBING, SECURITY WALL AND PERIODICAL SERVICES TO BOUNDARY WALL IN ZONE B AND SAINIK ARAM GRAH AT SUNJUWAN UNDER GE JAMMU

Amount

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each, including cutting holes for taking out holdfasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish (without any extra cost to Govt) and removing from site complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm each and not exceeding 4 Sqm, including cutting holes for taking out holdfasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish (without any extra cost to Govt) and removing from site complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each complete and removing from site complete all as specified and directed by Engineer-in-Charge.

Taking down shutters and refixing in same opening after resecuring or easing and adjusting, also refixing builder's hardware as required including renewal of unserviceable screws etc of any description exceeding 1 Sqm and not exceeding 2 Sqm each complete all as specified and directed by Engineer-in-Charge.

Material and Labour for factory made pressed steel frames of size 105 x 60mm made out of PBI sheet 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete including bottom of each chowkat to be welded with 02 no's 25 x 25 x 3mm angle iron projecting 10cm one either side including one shop coat of red oxide chrome primer and including PCC (1:3:6) type C-0 in back filling of chowkats and tarring back of chowkats and holdfasts complete all as specified and directed by Engineer-in-Charge.

Material and Labour for factory made pressed steel frames of size 125 x 60mm made out of PBI sheet 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete including bottom of each chowkat to be welded with 02 no's 25 x 25 x 3mm angle iron projecting 10cm one either side including one shop coat of red oxide chrome primer and including PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) in back filling of chowkats and tarring back of chowkats and holdfasts complete all as specified and directed by Engineer-in-Charge.

Supply and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet and edges will be painted to match with printed sheet, reinforced with mild steel square tube, supplying and fixing in opening as per specification complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 30 mm thick PVC factory made panel door shutter (style) consisting of frame made out of mild steel tubes for top and bottom rail, mild steel frame shall be covered with heat moulded wood grain printed PVC channel and 5 mm thick X 15 mm wide PVC sheet beading used inside style and rails and decorative PVC beading of 10 x 10 mm used instead of exposed portion of PVC sheet beading as in toilet / kitchen cabinet shutters complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 30mm thick flush shutters, soild core construction, with particle board core and plywood face panels, both faces are covered with decorative face veener with lipping / frame to match complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 35mm thick factory made Ist class hard wood, glazed and skelton shutter open, rebated and prepared to receive glass, gauge, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR 2020 Pt-I Section 8.24(b) supplied and fitted to chowkhats complete all as specified and directed by Engineer-in-Charge.

Supply and fixing mild steel butt hinges medium weight 100 mm long complete all as specified and directed by Engineer-in-Charge.

Supply and fixing box type steel windows / Ventilator (factory made) outer frame made out ERW tube 'P' section 65 X 45 X 25 mm and shutter of ERW tube 'P' section 50mm X 35mm X 20mm openable (double shutter) with glazed shutter on external side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 no's on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler / AC window complete all as specified and shown on drawing No CEPZTD-324/07 Sh 1/3 to 3/3. Note:- The quoted rates shall also include: - (i) One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrete surface. (ii) 4 no's MS steel lugs made of 20 X 5 mm Iron flat 200 mm long. (iii) 10 mm Sq Bar grill / guard bar design as per drawing. (iv) PCC block for embedding lugs.

Supply and fixing in repairs 18 / 19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws / nails to timber / steel frame work as in shelves, cup board shutters, book case, writing table stand, shelves etc including fixing of plain fillets square or rectangular of 2nd class hard wood not exceeding 3 Sq.cm in leaping to shutters / shelves compete fixed all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair continuous piano hanges, mild steel, bright finish or electrogalvanised, width of flap 30mm (when open) fixed with welding complete all as specified and directed by Engineer-in-Charge.

S & F Hasp & staple size 100 mm, alumium anodised, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed by Engr-in-Charge.

S&F Aluminium handle cast type, anodised size 150mm long, D type complete all as specified and directed by Engr-in-Charge.

S&F Aluminium anodised barrel tower bolts, with bright bolt and fixed 200mm complete all as specified and directed by Engr-in-Charge.

S&F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repairs Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks,or galvanised wire staples complete all as specified and directed by Engr-in-Charge.

S&F in repairs Helical door spring 150mm including roller and roller plate complete fixed with welding to existing steel chowkhats complete all as specified and directed by Engr-in-Charge.

Hacking out old broken glass of any thickness, size, quality or description from the wooden/ steel frames glazing with puttyor fixed with wooden beads complete all as specified and directed by Engr-in-Charge.

S&F 3mm thick ordinary glass sheet quality and glazing with oil putty in square n. exc 0.5 sqm in each pane including punching or drilling out old glazing pins or spring clips and providing and fixing new clips or pins, including scaffolding to reach up to 4 story building complete all as specified and directed by Engr-in-Charge.

Description all as per serial item no 22 above but frosted glass complete all as specified and directed by Engr-in-Charge.

M&L applying two coats of synthetic enamel paint on wooden surface over one coat of pink primer including prepartion of new surface over 10cm width or girth complete all as specified and directed by Engr-in-Charge.

M&L for two coat synthetic enamel paint on new steel surfaces of any description not otherwise described over 10 cm width or girth including preparation of new surface complete all as specified and directed by Engr-in-Charge.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps cills, sunshades, shelves,lintels etc; and cutting chases for concealed water tubing and making good, cutting not exc. 10cm girth complete all as specified and directed by Engr-in-Charge.

Taking up or down steel tubing with connections for cleaning complete of bore 15mm complete all as specified and directed by Engr-in-Charge.

Taking up or down steel tubing with connections for cleaning complete of bore 20mm complete all as specified and directed by Engr-in-Charge.

S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15mm, complete all as specified and directed by Engr-in-Charge.

S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs,unions etc.) of nominal bore 20mm, complete all as specified and directed by Engr-in-Charge.

Refixing only 15mm dia steel tubing and connections in new or old position including cleaning of old steel tubing complete all as specified and directed by Engr-in-Charge.

Refixing only 20mm dia steel tubing and connections in new or old position including cleaning of old steel tubing complete all as specified and directed by Engr-in-Charge.

M&L for Opening of air lock/blockage in GI pipe line from outlet of water tank to all internal GI pipes/ fittings to smooth flow of water from bibtaps/ shower/WHB pillar tap/stop valves complete by air pressure/ water gravity pressure etc complete all as specified and directed

M&L for Replacing 15 mm GI fittings of medium grade ISI mark like butt Elbow, socket, nipple, union socket, tee etc complete all as specified and directed by Engr-in-Charge.

M&L for Replacing 20 mm GI fittings of medium grade ISI mark like butt Elbow, socket, nipple, union socket, tee etc complete all as specified and directed by Engr-in-Charge.

Complete removal of vegetations,roots and shurbs from wall and making good the wall with cement,brick work and plastering including all scaffolding up to 4 storey building complete all as specified and directed by Engr-in-Charge.

M&L for Disconnecting existing tanks of capacity exc 250 ltrs but n exc 500 ltrs, setting aside for repairs, cleaning etc and hoisting if required reconnecting and refixing in position after Cleaning and removing all scale dirt etc from tanks complete, all as directed at site and writing date of cleaning with synthetic enamel paint complete all as specified and directed by Engineer-in-charge.

M&L for Disconnecting existing tanks of capacity exc 500 ltrs but n exc 1000 ltrs, setting aside for repairs, cleaning etc and hoisting if required reconnecting and refixing in position after Cleaning and removing all scale dirt etc from tanks complete, all as directed at site and writing date of cleaning with synthetic enamel paint complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC low level flushing cistern valve less,syphonic action type of 10 ltrs capacity white with inlet, ball valve, float and handle incl. cast iron brackets, PVC flush pipe 32mm dia ,PVC connection (15x 450 mm) long complete all as specified and directed by Engr-in-Charge.

Material and Labour for Repairing of PVC low level/high level cistern by changing its internal fitting including PVC flush pipe etc complete all as specified and directed by Engr-in-Charge.

S&F in repair Vitreous china squatting pan 'Orissa' pattern ' size 580x440mm white, with integral foot rest 'P' or 'S' trap,front or back inlet including connection to trap and to flushing pipe,anti syphonage pipe, etc. Complete making good to floor as existing complete all as specified and directed by Engr-in-Charge.

S&F in repairs Vitreous china wash down water closet pan (pedestal pattern), white including fixing bolts,flush pipe and joints complete all as specified and directed by Engr-in-Charge.

S&F in repairs Vitreous china wash hand basin white ,flat back of size 550x400mm including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed by Engr-in-charge.

S&F in repairs Pillar tap fancy type chromium plated with capstan head,screwed down high pressure with long screwed shanks and fly nuts,screwed for iron pipes 15 mm bore dia complete all as specified and directed by Engr-in-charge.

S&F in repairs brass CP Mixer of bore dia of pipe 15mm for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed by Engr-in-charge.

Dismantling PVC water tank of capacity upto 1000 ltrs complete all as specified and directed by Engr-in-charge.

S&F Rotational moulded polyethylene water storage tank including, plastic lid cover, double layered, cylindrical vertical with closed top hoisted and fixed in position of capacity 500ltrs including making connections,20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe anf fixed (min wt210 gram) complete all as specified in SSR Part I.

S&F Rotational moulded polyethylene water storage tank including, plastic lid cover, double layered, cylindrical vertical with closed top hoisted and fixed in position of capacity 1000 ltrs including making connections,20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ballscrewed for iron pipe anf fixed (min wt210 gram) complete all as specified in SSR Part I.

S&F in repairs Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms) of 15 mm bore complete all as specified and directed by Engr-in-charge.

S&F in repairs 20 mm dia Ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ballscrewed for iron pipe anf fixed (min wt 210 gram), screwed for iron pipe or brass ferrule and fixed complete all as specified and directed by Engr-in-charge.

Repairing of existing float valve by replacing its rod of brass or plastic float of any description complete all as specified and directed by Engr-in-charge.

Taking down cement plaster of any description on brick or stone walls or from concrete surface incl raking out joints, hacking for key,scrubbing down with water and removing unserviceable material outside cantt area complete all as specified and directed by Engr-in-Charge. (Note: Plaster work may be in patches upto triple storey)

M&L Rendering 10 mm thick in CM 1:6 on fair faces of brick surface finished even and smooth without using extra cement upto height of four storey building complete all as specified and directed by Engr-in-charge.

M&L Rendering 5 mm thick in CM 1:3 on fair faces of concrete surface of ceiling, finished even and smooth without using extra cement , complete all as specified and directed by Engr-in-charge.

M&L Rendering 15mm thick in CM 1:4 in two layers of 10 mm thick and 5 mm thick with WPC on fair faces of brick surface finished even and smooth without using extra cement etc complete all as specified and directed by Engr-in-charge.(Including all necessary scaffolding lifiting arrangement for external surfaces).

M&L for two coats of oil bound distemper to newly plastered surfaces including preparation of surfaces complete all as specified and directed by Engr-in-charge.

M&L applying two coats of cement base paint over a coat of primer including preparation of new plastered surface complete all as specified and directed by Engr-in-charge.

Complete removal of existing treatment and applying two coat of exterior emulsion paint on old surface of chajjas including preparation complete all as specified and directed by Engr-in-charge.

M&L for two coats of oil bound distemper to old plastered surfaces of wall including preparation of surfaces complete all as specified and directed

M&L applying three coats of white wash on ceiling including preparation of newly plastered surface complete all as specified and directed by Engr-in-charge.

Dismantling floors hearth or wall tilling including cement mortor bedding (but not backing) removing unserviceable materials outside MOD area and rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L Non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm,in floors etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed by Engr-in-charge.

M&L Non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.18 sqm but not exc 0.38 sqm,in floors etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed by Engr-in-charge.

Description same as per item no 64 above but as in skirting including 10 mm thick rendering in cement mortar 1:4, complete all as specified and directed by Engr-in-charge.

M&L Vitrified tiles light shade 10mm thick (square/rectangular) polished,area of each tiles not exceeding 0.36 sqm, as in floors etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match shade over and including screed bed 15mm thick in CM 1:4 complete all as specified and directed.

M&L Vitrified tiles light shade 10mm thick (square/rectangular) polished,area of each tiles not exceeding 0.36 sqm,as on vertical surfaces etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match shade over and including 10 mm thick screed in CM 1:4 complete all as specified and directed .

M&L Glazed ceramic coloured tiles 300x450x7 to 8 mm thick on vertical surface as in skirting,dado set and jointed with neat cement slurry and pointed in white or coloured cement to match with the surface over and including taking down old plaster and 10 mm thick screed in CM 1:4 complete all as specified and directed.

Rougening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed.

M&L Granite 18 to 20mm thick (Pure black) (tabled rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar 1:4 including pointing in colour cement 1:2 using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screedbed in cm1:4 edges of slab to be rounded from all sides (including cutting, wastage and polishing) complete all as directed.

Supply only liquid water proofing compound complete all as specified and as directed.

S&F in repairs chromium plated bib tap 15mm size with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-charge.

S&F in repairs Bib tap of bore 15mm standard of PTMT any colour high pressure screwed for iron pipe and fixed.(Minimum weight 15mm -90 gm) complete all as specified and directed by Engineer-in-charge.

S&F in repair CP health faucet with 1 mtr long CP flexible pipe complete all as specified and directed by Engineer-in-charge.

S&F in repair angle/stop valve of cast copper alloy screwed down high pressure with crutch or butterfly handle screwed bother ends for iron pipe or for uniorns and fixed 15 mm bore complete all as specified and directed by Engineer-in-charge.

S&F in repairs brass chromium plated shower rose 125mm size any colour with or without swivel joints, arm 15mm size 195mm long including fixing to steel pipe or union complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC connection 15mm, 450mm long with nuts and washers complete all as specified and directed

M&L for 75mm thick cement concrete (1:3:6) type C-1 (using 20mm graded stone aggregate) as in floor/plinth protection laid in suitable panels finished even and fair all as specified. 6mm Joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 gde and three part of sand (all by weight) complete all as specified and directed by Engineer-in-charge.

M&L in repair for double action floor spring hydraulically regulated made of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed by Engineer-in-charge.

S&F in Repair to Aluminium door including adjusting , necessary bedding, clip, rubber beader, repair to floor door closer complete all as specified and directed by Engineer-in-charge.

S&F 5.50 mm thick sheet glass fixing for Aluminium doors and windows including 25 micron reflective type sun control film complete all as specified and directed by Engineer-in-charge.

S&F in repair Aluminium (extruded section) body door closer hydraullicaly regulated designation No 2, universal type suitable for door shutters of 701 to 850mm in width and of weight between 36 and 60kg and fixed complete all as specified and directed by Engineer-in-charge.

S&F in repairs waste coupling of PTMT (half or full threaded) of bore dia 32 mm discharge pipe complete all as specified and directed by Engineer-in-charge.

Material and Labour for Repairing of existing Bib cock by replacing its jumper/washer etc to make it functional complete all as directed at site complete all as specified and directed by Engineer-in-charge.

S&F in repair brass Phase for CP bib tap, pillar tap, angle valve for suitable 15mm dia full turn, half turn as per sample complete all as specified and directed by Engineer-in-charge.

S&F in repair Grating doom 100mm dia without hole chromium plated complete all as specified and directed by Engineer-in-charge.

S&F in repair Grating doom 100mm dia with hole,chromium plated complete all as specified and directed by Engineer-in-charge.

S&F in repair 15mm bore long body Bib tap cast copper alloy fancy type chromium plated with capstan handle screwed down screwed for iron pipe or for brass ferrule. complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC Waste pipe 32 mm dia and suitable length straight or flexible type for wash hand basin / sink complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC tank cover for water stoarage tank for 500 ltr capacity including locking arrangement complete all as specified and directed by Engineer-in-charge.

S & F in repair 110 mm dia bore PVC (SWR) pipes single socketed in any length with solvent cement joints, fixed to wall complete all as specified and directed by Engineer-in-charge.

S & F in repair 75 mm dia bore PVC (SWR) pipes single socketed in any length with solvent cement joints, fixed to wall complete all as specified and directed by Engineer-in-charge.

S&F in repairs PVC SWR bends of bore 110mm dia complete all as specified and directed.

S&F in repairs PVC SWR bends of bore 75 mm dia complete all as specified and directed.

Removing existing treatment from roof surfaces such as tiling, tarfelt, fungus,moss,dust etc.,cleaning the surface of all foreign material by wire brushing and dusting and racking out RCC slab complete all as spd and removing the debries outside defence land complete all as specified and directed by Engineer-in-charge.

M&L for Rendering 20 mm thick in CM 1:4 on fair face of brick work surfaces finished even and smooth without using extra cement up including mixing liquid water proofing compound complete all as specified and directed by Engineer-in-charge.(Note- liquid water proofing compound shall be measured and paid seperately)

Cleaning the roof surfaces and applying bitumen primer @ 0.30 kg/sqm, providing and laying 3mm thick APP modified water proofing membrane weighing not less than 3.00 kg/sqm reinforced with non woven polyester mat weighing not less than 160 gm/sqm, having softening point not less than 800 N /Sq cm, tearing strength of 180N, with minimum of 10 cm side laps and 15cm end laps, laying by application of torch, and applying industrial bitumen 85/25 @ 1.2 kg/sqm on top surface complete all as specified and directed by Engineer-in-charge.

Taking down steel rolling shutters of size exc 10sqm but n'exc 30 sqm gear operated type and fixing in the same opening after carrying out repair of Oiling and greasing with approved make of lubricant to guide rails, repair/replacing of gear box etc of rolling shutter of any size including rolling straightening of any strip, hood cover, guide rail, suspention shutter shaft, pullies, helical wire spring and tightening of rolling springs complete all as specified and directed by Engineer-in-charge.

Taking down steel rolling shutters of size n,exc 10sqm manual/push pull type and fixing in the same opening after carrying out repair of Oiling and greasing with approved make of lubricant to guide rails etc including rolling straightening of any strip, hood cover, guide rail, suspention shutter shaft, pullies, helical wire spring and tightening of rolling springs complete all as specified and directed by Engineer-in-charge.

Demolition Brickwork or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engineer-in-charge.

M&L Brickwork with sub class "B" bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 complete all as specified and directed by Engineer-in-charge.

Description all as per serial item no 101 above but except bricks complete all as specified and directed by Engineer-in-charge.

M & L 15 mm thick rendering on brick work or concrete surface in cement mortar 1:4, surface finished even and fair without using extra cement complete all as specified and directed.

M&L applying one coat of cement base paint including preparation of old plastered surfaces of any description in any pattern / colour complete all as specified and directed.

Dismantling cast iron work ie fencing posts, horns, barbed wire etc in compound wall in any condition and in any position complete all as specified and directed.

M & L mild steel angle iron work as in posts (swan neck), struts in fencing, grills grating etc, including cutting to shape, drilling hole, notching for wire etc. including all necessary drilling bolting or reveting etc and similar work confirming to FE-410-O or 310-O, complete all as specified and directed.

S&F in repair barbed wire, galvanized steel, 2 strand 2.24 mm dia with 2mm dia barbs at 75mm spacing straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossings with and provision of galvanized mild steel wire, staples or steel pins, etc complete all as specified and directed. (each line wire to be measure) .

S & F precast cement concrete louvres and jallies, 40mm thick (measured solid), including all moulding and set in 1:4 cement mortar complete all as specified and directed.

NOTE NO 1: - Samples of materials as approved will be kept in GE's sample room. NOTE NO 2: - All fittings and fixtures mentioned above will be fixed to the satisfaction of Engr-in-Charge and GE. NOTE NO 3: - Warranty certificate to the Engineer-in-Charge where ever applicable shall be submitted by the Contractor at the time of fittings.

M/S PRITHIVI RAJ AND SONS

ASHFAQ AHMED MANHAS

M/S CJ CONSTRUCTIONS

M/S Shesh Paul Gupta

M/S TRIKUTA BUILDERS

M/S BALWAN SINGH

Bidder Name

M/S Shesh Paul Gupta

M/S VED PAUL MAHAJAN

M/S TRIKUTA BUILDERS

ASHFAQ AHMED MANHAS

M/S PRITHIVI RAJ AND SONS

M/S CJ CONSTRUCTIONS

M/S BALWAN SINGH