Special repair of PHC Kadma in Charkhi Dadri Distt. (Reinvite)

Amount

Dismantling brick work, Tile masonary or tile linning & tile terracing in cement (HSR 8.5,b)

Removing door and windows (wood and steel) with howkats by makig recesses in walls whe the wall is not to be dismantled(HSR 8.18,a,b) Door

Windows

Scraping cement plaster (HSR 8.32,c)

First class brick work laid cement sand mortar 1:4 in foundation and plinth (HSR 11.4)

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 meters above plinth level (HSR 11.7)

Tile teracing with one layer of tiles 22.86 cmx1.43cm x3.81cm laid dry over a layer of mud mortar including grouting with cement sand mortar 1:3 and top surface to be left clean(HSR 13.14)

12mm thick cement plaster 1:4(HSR 15.5)

Factory manufactured panelled and glazed door shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash, etc.(non-coniferous timber other than teak, conforming to I.S. specifleation no. 1003, kiln seasoned), with 100mm wide vertical styles 150mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 12 mm thick commercial veneered both sides particle board or plywood of B.W.R. grade, hot-pressed, including cost of iron hinges, screws, chocks/cleats, stops and nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above but including labour for fixing the same in position : 30mm thick (17.91,c (-) Note 17.18)

Factory manufactured wire gauze door and windows shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash etc. (non coniferous timber other teak, conforming to I.S. specification NO.1003, kiln seasoned) with 100mm wide vertical styles, 150mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above but including labour for fixing the same in position : 30 mm thick

Factory manufactured solid flush door shutters , with block board core as per IS 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot –pressed , conforming to IS 2202 part I and II , fixed in position , including iron hinges , screws , chocks /cleats and stops , etc (excluding the cost of any fittings other than specified above , but including labour for fixing the same in position . Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges. (i) 30mm thick

Providing and fixing DND fibre shed (NS)

Providing and laying 80mm thick interlocking paver blocks of all shapes and colours in design mix cement M-35 over a bed of 30mm thik fine sand complete in all respect.(HSR 10.159)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge), INDIAN TYPE ORISSA OR ORYA WATER CLOSET SUITE for sinking into floor, with raised foot treads COMPLETE WITH 100 MM H.C.I. ‘P’ TRAP with or without vent as required and all OTHER NECESSARY FITTINGS as fully described in item no.30.1 above. (HSR 30.2 b i)

Providing and fixing in position best indian make (as approved by the engineer-in-charge European type water closet suite, syphonic type consisting of- (i) VITREOUS CHINAWARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge). (ii) One piece SEAT AND LID IN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge) COMPLETE in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS. (b) Double trap syphonic (ii) Single Color. [HSR 30.5 (b) (ii)].

EXTRA OVER item nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY VITREIOUS CHINA HIGH LEVEL CISTERN COMPLETE with internal brass fittings instead of 12.5 litres capacity high level C.I. cistern complete (as approved by the Engineer-in-charge) (i) White (HSR 30.8)

EXTRA OVER item nos. 30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow Black or white plaster seat and lid.(i) White plastic seat (Solid). [HSR 30.13 (i)].

PPROVIDING AND FIXING IN POSITION BEST INDIAN MAKE A RANGE OF THREE STALL URINALS 1150 MM HIGH IN VITREIOUS CHINAWARE WITH ONE NO. 10 LITRES CAPACITY C.I. AUTOMATIC FLUSHING CISTERN WITH FITTINGS AND FLUSH PIPE COMPLETE as fully described in item no. 30.29 above. (HSR 30.31 i)

Providing and fixing 25 mm thick marble partition for different type of urinals. Small size 680mm x 330 mm Single Color(HSR 30.40 b ii)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE LAVATORY SUITES (WITH FULL ANTI SPLASH RIM IN VITREIOUS CHINAWARE and all other necessary fittings as fully described in item no.30.41 above. White Size 510 mm X 400 mm with one no tap(HSR 30.42 i)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE CHROMIUM PLATED BRASS 2ND TAP FOR LAVATORY SUITE. (HSR 30.45)

Providing and fixing in position best quality Stainless Steel Sinks with Complete fittings as fully described in item No. 30.51. (a) 600 mm x 450 mm x 200 mm. [HSR 30.53 (a)].

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE TOWEL RAILS FIXED in with rawlslugs embedded in walls with C.P. brass screws. Complete in all respect INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (d) CP Brass two swivel towel rail 400 mm long (HSR 30.68 d)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRROR mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHROMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (HSR 30.71 a i)

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-charge). [HSR 30.75]. (a) Bib cock long body.

(c) Bib cock

Providing & fixing in position C.P. brass stop cock (as approved by the engineer-in-charge). (a) 15 mm Stop cock. (ii) Concealed stop cock with flange. [HSR 30.76 (a) (i) Stop cock male and female end

(ii) Concealed stop cock with flange

Providing and fixing 15 mm C.P. brass Laboratory cock swan neck of best quality (to the approval of the Engineer-in-charge) two way (HSR 30.78 b)

Providing and fixing in position best Indian make flexible tube connection. (a) aluminium (iii) 15mm x 450 mm. [HSR 30.82 (a) (iii)].

Providing and fixing in position H.C.I. Soil waste vent or antisyphonage pipes to I.S.I. specifications of E.L.C. manufacture or of any other reputed firm including cutting and wastage etc. and cutting holes in walls, roofs or floor etc. and making good to its original condition but excluding cost of lead jointing. (HSR 30.84) (a) 100 mm internal diameter.

Cutting chase in brick wall in cement or in floor for embedding G.I. or H.C.I. pipe lines and making good the same to its original condition. [HSR 30.95 (a)]. (a) Size 75 mm x 75 mm.

AMIT KUMAR CONT