Shifting of 33 KV, 11 KV and LT Lines Due to Road Widening From Nabi Panah to Andhe ki Chauki Road (Chanaige no. 02, 02-04 Km) Lucknow.

Amount

Laying and Jointing PVC Pipe. Heading

Safe loading & carriage including unloading & proper stacking of following store materials from ESC Daliganj/JE store to site of work.

11KV 3X185 SQ MM XLPE CABLE

11KV END TERMINATION O/DOOR & I/DOOR 3X185 SQ MM

ACSR CONDUCTOR Dog

ABC 3X95+1X70+1X16

ABC SINGLE PHASE (1x16+1x25)

3.5X240 SQ MM PVC CABLE

11/0.4 KV 100 KVA T/F

11/0.4 KV 63 KVA T/F

STP 11 M LONG

V TYPE X-ARM ANGLE 65X65X6MM

11KV PIN INSULATOR

11KV PIN WITH NUT

M S EARTHING ROD 20X2500 MM

M.S. CHANNEL 100X50MM

11KV DISC INSULATOR T&C

GI WIRE 8 SWG

STAY WIRE

DISC FITTING T&C

M.S. ANGLE IRON 65X65X6MM

33 KV LINE WORK

Fabrication & erection of single pole support for 33 KV line on 11 M long ST Pole with fixing of necessary clamp & other acessories like 1 no. Channel cross arm, Danger board, barbed wire etc. contractor shall provide, necessary clamps, F-Bracket etc. as per RESPO norms.

Fabrication, erection of sectional double pole for 33 KV line on 11 M long ST Pole with fixing of necessary clamps & other accessories like 1 no. top channel 125X65 mm - 3.24 M 1 no. Guarding Angle 3.5 mtrand 3 X bracing, No plate, danger board and barbed wire,installation of 8 no stay set included in this work etc.(all material arranged by contractor except steel & pole & insulators).as per RESPO norms.

Fabrication, erection of tri pole for 33 KV line on 11 M long ST Pole with fixing of necessary clamps & other accessories like 2 no. top channel 100X50 mm - 3.24 M. 2 no. Guarding Angle and 3 X bracing etc ono plate, danger board barbed wire etc.(all material arranged by contractor except steel & pole & insulators).as per RESPO norms.

Fabrication, erection, of end type double pole of with one side cable exposure for 33 KV line on 11 M long ST pole with fixing of necessary clamps & other accessories like disc insulator, 1 no. top chennel 125×65 mm - 3.20M & 1 no. gaurding angle and 1 no. X bracing,disc fittingits,33kv pin with pin insulator ,danger board,number plate,barbed wire,jumpering by PG clamp etc. (all material arranged by contractor except steel,insulator,disc insulator with fitting & pole).as per RESPO norms.

Conversion of existing 33 KV single pole support into section type double Double pole by fixing of 1 no top channel 125x65 mm of 3244 mm, 1 no guarding angle 3500 mm long 6 nos 33 KV disc fitting and disc insulator 24 no 3 no pin and 33 KV pin Insuator and other associated work grouting , painting and plinthing of new pole also include this work(all material arranged by contractor except steel & pole & insulators)as per RESPO norms.

Erection of single stud pole support on ST pole 11 M long with fixing of necessary clamps and other accessories required for erection.

Providing , Stringing and sagging of three nos. 6SWG Earth/GI wire with caddle guarding of above 33KV line one span as per RESPO Norms. Including provision of all necessary clamps and hooks. Shifting of existing line conductor of 11 KV/LT lines to maintain proper clearence in between both lines.(All Materials provided by contractor except GI wire 6 SWG)

Laying of 33 KV XLPE Cable.

Double circuit Cable laying in normal soil by digging of trench 1050 mm deep, 750 mm wide including supply of required material as fine sand, 1st class bricks, stone slab. Inter axial spacing between the two cable should be in between 0.25 m to 0.40m. the two cables should be seprated by a partition of single bricks (All the material required for laying will be supplied by the contractor except 33 KV XLPE cable)

Cable laying By dirll method Single circuit

In RCC pipe single circuit.

In MS pipe 200 mm dia single circuit.

In HDPE pipe 160 mm dia

Fixing of cable marker on 33 kv cable route.dipitching feeder name and voltage on route marker

Temporary Laying of 33 KV XLPE Cable.

Temporary Laying of 33 KV XLPE Cable as per site requirement.

Dismantling and rerolling of temporary laid 33 KV 3x300 sq mm XLPE cable as per site requirement

Temporary hoisting and dehoisting of 33 KV XLPE cable 3x300 sq mm

Hoisting of 33KV XLPE cable on double pole with MS pipe of size 5/6" dia 3 M long including its jumpering complete with clamps, nuts and bolts(all material arranged by contractor).

Digging of pit of size 3x2x1.2 mtr. for making straight through joint 33 KV after making of joint the joint should provide cushioning and covering by brick sand and stone slab .Work included filling of soil,leveling and ramming of the same .( S/Th Provided by department)

Stringing & sagging of three phase 33 KV line on ACSR Dog conductor as per RESSPO Norms.

Providing ,Stringing and sagging of three nos. 6SWG Earth/GI wire with caddle guarding of above 33 kv line one span as per RESPO Norms. Including provision of all necessary clamps and hooks. Shifting of existing line conductor of 33 KV lines to maintain proper clearence in between both lines.(All Materials provided by contractor except GI wire)

Making proper markig of cable by markig tape/marking tag st proper interval (every 0.5 mtr underneath ) marking tape /tag provided by contractor

Plotting of cable layout rute on graph paper (i.e. depth underneath and distance from either side from prominent reference fixed point ) the reference point must not be more than 100 mtr.

11 KV & LT LINE WORK

Fabrication & erection of 11 KV cable exposure type double pole with the provission of cable with fixing of necesory clamps and other acessories like danger board,number plate,barbed wire,2 no. channels 100x50 mm (1600mm each),1 no.MS channel 100x50mm(3200mm in length) for supporting the hoisting of cable & poles.its jumpering by single core PVC aluminium cable with proper size Al.lug after making three phase busbar with help of 11 KV pin,pin insulator and PVC cable. (all material arranged by contractor except steel,pole,PVC aluminium cable & insulator).as per RESPO norms.

Fabrication & erection of S/S type double pole for 11KV line on 11 M long ST pole with fixing of necessary clamps & other acessories like 1 no. top channel 100×50 mm,2 no.MS angle 65x65x6mm,danger board,number plate,barbed wire,TPMO set & D.O.fuse set.

Fabrication, erection of Single pole for . 11 KV line on 11 M long ST Pole with fixing of necessary clamps & other accessories like 1 no. 11KV V-type Cross arm,1 no. Guarding Angle 65x65x6.

Fabrication, erection of single section pole for 11 KV line on 11 M long ST Pole with fixing of necessary clamps & other accessories like 1 no. top channel 100X50 mm - 2.24 M. 1 no. Guarding Angle disc fitting and disc insulators etc.(all material arranged by contractor except steel & pole and insulators ).as per RESPO norms.

Fabrication, erection of double pole for end terminations with one side cable exposure for 11 KV line on 11 M long ST Pole with fixing of necessary clamps & other accessories like 1 no. top channel 100X50 mm - 2.24 M. 1 no. Guarding Angle and X bracing etc.(all material arranged by contractor except steel & pole).as per RESPO norms.

Fabrication, erection of sectional double pole for 11 KV line on 11 M long ST Pole with fixing of necessary clamps & other accessories like 3 no. top channel 100X50 mm - 2.24 M 2 no. Guarding Angle and 3 X bracing etc.(all material arranged by contractor except steel & pole & insulators).as per RESPO norms.

Fabrication, erection of for conversion of existing single pole supprt into sectional double pole for 11 KV line on 11 M long ST Pole with groting plinthing and paintig of one st pole in the alignment of existing pole fixing of necessary clamps & other accessories like 3 no. top channel 100X50 mm - 2.24 M 2 no. Guarding Angle and 3 X bracing etc.(all material arranged by contractor except steel & pole & insulators) necessary stay set shall be provided by contractor at his own cost.as per RESPO norms.

Fabrication, erection of tri pole for 11 KV line on 11 M long ST Pole with fixing of necessary clamps & other accessories like 1 no. top channel 100X50 mm - 2.24 M. 1 no. Guarding Angle and X bracing etc.(all material arranged by contractor except steel & pole & insulators).as per RESPO norms.

Erection of single stud pole support on ST pole 9 M long with fixing of necessary clamps and other accessories required for erection.

Holding of exsting 11KV overhead line on exsting D/P or S/P for enabling removal of conductor on one side of 11 KV overhead line ,its stringging on D/P or S/P .(agency also to provide temporary stay at the time of dismantaling of overhead line)

Providing , Stringing and sagging of two nos. 6SWG Earth/GI wire with caddle guarding of above 11 kv line one span as per RESPO Norms. Including provision of all necessary clamps and hooks. Shifting of existing line conductor of 11 KV/LT lines to maintain proper clearence in between both lines.(All Materials provided by contractor)

Stringing & sagging of three phase 11 KV line on ACSR Dog conductor as per RESSPO Norms. (Conductor provided by the department. )

Laying of 11 KV XLPE Cable.

Double circuit cable laying in normal soil by digging of trench 1050 mm deep, 750 mm wide including supply of required material as fine sand, 1st class bricks, stone slab. Inter axial spacing between the two cable should be in between 0.25 m to 0.40m. the two cables should be seprated by a partition of single bricks (All the material required for laying will be supplied by the contractor except 11 KV XLPE cable)

S/C Cable laying in normal soil by digging of trench 900 mm deep, 500 mm wide including supply of required material as fine sand, 1st class bricks, stone slab. (All the material required for laying will be supplied by the contractor except 11 KV XLPE cable)

Cable laying By dirll method Single circuit

Laying in RCC hume pipe with coller NP-4 200 mm dia single circuit.

In MS pipe 4" dia single circuit.

In HDPE pipe 160 mm dia

Laying of 11 KV XLPE Cable in HDPE pipe 160 mm dia by horizontal deep drilling method

Fixing of cable marker stone on 11 KV cable route and dipitching of feeder name and voltage on cable marker

Hoisting of 11KV XLPE cable on double pole with MS pipe of size 5/6" dia 3 M long including its jumpering complete with clamps, nuts and bolts(all material arranged by contractor).

Digging of pit of size 3x2x1 mtr. for making straight through joint 11 KV work included filling of soil leveling and ramming of the same .( S/Th Provided by department)

Making proper markig of cable by markig tape/marking tag st proper interval (every 0.5 mtr underneath ) marking tape /tag provided by contractor

Plotting of cable layout rute on graph paper (i.e. depth underneath and distance from either side from prominent reference fixed point ) the reference point must not be more than 100 mtr.

High Pressure testing of 33 KV & 11 KV XLPE cable. Testing equipment will be arranged by the contractor.

33 KV cable

11 KV cable

LT WORK

Placement of 11/0.4 KV T/Fs on S/S Type D/P & installation,commissioning of 100/63/25/ KVA T/F including cost of L-pieces and lugs jumpering with the system ( All the required matrial for above job shall be provided by contractor except T/Fs)

Earthing by way of boring and lowering of "B" class GI pipe 50mm dia from ground upto the water level (minimum 30 meter deep) as per standard practicel(all material arranged by contractor including GI flat 50x6 mm ).

Installation of tell less fuse unit on D/P for 100/63/25 KVA T/F (Tell less fuse unit provided by contractor)

Laying of LT PVC Cable 3.5x240/3.5x400/3.5x70 sq mm D/C Cable laying in normal soil by digging of trench 900 mm deep, 650 mm wide including supply of required material as fine sand, 1st class bricks, stone slab. Inter axial spacing between the two cable should be in between 0.25 m to 0.40m. the two cables should be seprated by a partition of single bricks (All the material required for laying will be supplied by the contractor except cable)

Laying in RCC hume pipe with coller NP-4 200 mm dia single circuit.

In MS pipe 4" dia single circuit.

Fixing of cable marker on LT cable route

Construction of T/F plinth of size 2x2x1.5 m on a padding 0.25M deep in ground 1:5:10 cemend sand and brick ballast on the top of padding brick work Ist class brick of 0.95 mtr hight & 0.35 mtr wall will be constructed.Rest wall should be 0.23 mtr thick.brick work in ratio 1:4 cement & cores Sand in the hollow portion the sand should be fiilled from the ground level up to 15 centimeter below from the top of wall,Cement,sand & brick Ballasts should be filled up to 15 centimeter.Two no. of channel 100x50 in length 1500mm will be grouded.0.35 CM.RCC will be done with cores sand,cement and stone ballast in the ratio of 1:2:4.The t/fs plinth should be plastered on all sides 12mm thick in ratio 1:6 by cement and cores sand. (All the material will be arranged by the contractor .)

Placement of 11/0.4 KV T/Fs from dump place to newly constructed T/Fs plinth & installation,commissioning of 400/250/100 KVA T/Fs of T/F Plinth and including jumpering with the system ( All the required matrial for above job shall be provided by contractor except T/Fs)

Costruction of toe wall around the 11/0.4 KV S/S,fuse unit size 0.75 Mt.At Base and 0.23 Mt. At top as per RESSPO Norms by lst class bricks in the ratio 1:6, Base concreting of the wall to be done in ratio 1:6:12 and plaster 12 mm thick in ratio 1:4.(all material arranged by contractor).

Construction of fuse unit plinth as per norms,,installation of fuse unit on newly constructed plinth.(all the materials arranged by contractor )

Hoisting, winding and jumpering of of LT cable size 3.5x240 sq mm between LT distribution box/fuse unit & constructed overhead line with proper lugging and clamping

Providing earthing strip size 50x6mm and connecting from earthing pipe/m.s.earting rod to fuse unit/tronsformer body/neutral earthing(Earthing rod & earthing strip arranged by contractor).

Opening of consumer connection from existing line again reconnection with newly ercted L.T. distribution box/pillar box.

3 Phase (cable provided by contractor)

Single Phase (cable provided by contractor)

Fabrication & erection of single pole for LT line on 09 M long ST pole with fixing of necessary clamps & other acessories like clamp hook,dead/suspension clamp,neutral clamp,ABC pressure clamp (if required) and danger board with clamp.(all material arranged by contractor except steel & pole if required).

Stringing,Sagging,winding and jumpering of LT line with AB Cable (3x120+1x95+1x16) conductor as per RESSPO Norms.(AB Cable provided by deptt and balance material like holding clamp,eye hook,suspension clamp and dead end clamp arranged by contractor .)

Stringing,Sagging,winding and jumpering of LT line with AB Cable (3x95+1x70+1x16) conductor as per RESSPO Norms.(AB Cable provided by deptt and balance material like holding clamp,eye hook,suspension clamp and dead end clamp arranged by contractor .)

Stringing,Sagging,winding and jumpering of LT line with single phase AB Cable conductor as per RESSPO Norms.(AB Cable provided by deptt and balance material like holding clamp,eye hook,suspension clamp and dead end clamp arranged by contractor .)

Mounting and fixing of LT distribution box 3 phase 4 wire on existing wall/ Pole support with proper clamping of flexible pipe for casing of cable at suitable place for giving supply.

Nozeling ,winding & grouting of stay set. (All the civil material & stay set will be arranged by the contractor except stay wre).

Fixing of earth rod (2500x20mm) as per norms. For earthing support of old existing poles of 33, 11 KV lines including 6 SWG GI/Earth wire . (earthing rod provided by department)

Fixing of earth rod (2500x20mm) as per norms. For earthing support of old existing poles of LT lines including 6 SWG GI/Earth wire . (All Materials provided by contractor)

Grouting,Plinting and Painting of new erected 11M long ST poles of single pole support,double pole cable exposures and end type poles of 11 &33 KV lines

Digging of Pit in kachcha/Pakka land in depth upto 1/6 length of Pole, Dragging of STP from near by place/Dump, Erection of Single pole along with stone pad in bottom with proper alignment of line for 33 KV line on 11 M long ST Pole and refilling with ramming of earth.

Grouting of pole in depth of 1/6 the length of pole in ratio 1:4:8 in cement sand and brick balast as per RESPO norms.

Construction of pole plinth 300mm x 450 mm above ground level in 1:2:4 in cement, coarse sand and stone gritt as per RESPO norms.

Painting of new erected ST pole with two coat of red oxide paint,PO red paint at top of pole 2 M & balance by two coats of best quality aluminium paint ISI of Burger/Nerolac/Asian mark as per norms.

Grouting,Plinting and Painting of new erected 9 M long ST poles of single pole supports for LT line and stud polse for LT, 11 & 33 KV lines

Digging of Pit in kachcha/Pakka land in depth upto 1/6 length of Pole, Dragging of STP from near by place/Dump, Erection of Single pole along with stone pad in bottom with proper alignment of line for 33 KV line on 11 M long ST Pole and refilling with ramming of earth.

Grouting of pole in depth of 1/6 the length of pole in ratio 1:4:8 in cement sand and brick balast as per RESPO norms.

Construction of pole plinth 300mm x 450 mm above ground level in 1:2:4 in cement, coarse sand and stone gritt as per RESPO norms.

Painting of new erected ST pole with two coat of red oxide paint,PO red paint at top of pole 2 M & balance by two coats of best quality aluminium paint ISI of Burger/Nerolac/Asian mark as per norms.

Providing of 4 No supervisory manpower on Temporary basis for the proper monitoring and execution of Projet/work.

Dismentling of 33 KV,11KV line, L.T. lines & distribution boxes and its dump at suitable place on site up to complition of work and its safe loading/unloading/weighing carriage from dump site to je"s store/ESC daliganj (Except broken PCC Pole).

Steel scrap of st Pole 11 Mt Long

11/.4 KV T/F 250 KVA

11/.4 KV T/F 25/63/100 KVA

11/.4 KV T/F 10 KVA

pcc pole

ACSR mix conductor

Steel material

Tree branches cutting and chopping where required aprox 1 KM.

Sidhi Enterprises

ARIHANT ELECTRIC COMPANY