Civil and Electrical works towards housing of pilot plant for non-leather footwear in Tannery building at CLRI Regional Centre, Jalandhar, Punjab 144021

Civil Items

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Dismantling cement asbestos or galvalume sheet or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials to CLRI store.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete below and above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls Under 20 cm wide

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, and paneling to be paid for separately) : For fixed portion powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, and paneling to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness (Make: M/s Ozone , M/s Godrej , M/s Hettich)

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 100 kg to 120 kg and door width from 701 mm to 1200 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.20 mm M.S. laths with 1.20 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 10.00 sqm and upto 16.80 sqm in the area

Removing dry or oil bound distemper, water proofing cement paint, interior emulsion paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Providing and applying white cement based putty (Make: " Birla wallcare putty" or Asian putty )of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Wall painting with premium acrylic emulsion paint of interior grade, with roller finish (Make:M/s. Asian, "Royale Health shield" or "Asian Aspira") consists of silver ion technology, superior stain resistance, teflon surface protector, enhanced Anti-microbal formula as per EN ISO 22196:2007 having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work.

Providing and fixing color coated/ pre-painted galvalume(Make: TATA / JSW / JINDAL or equilvaent) (Aluminium 55%, Znl 43.4% at SI-1.6%) profile sheets of approved design, minimum thickness of 0.5mm having yield strength of 550 MPA, coating mass of AZ 150 g/m2 including all complete as per ASTM - A792M (or) IS:277. The sheet shall be fixed using self drilling /self tapping screws of size (5.5 x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Finishing the fresh concrete surfaces with power driven trowelling machine before the initial setting time of concrete to obtain smooth, dense and to achieve neat finish of the concrete surfaces with even level complete all as required to suit site conditions along with necessary miscellaneous reparir works involved complete all as required to suit site conditions in all leads & lifts and all as directed by the Engineer-In-Charge.

Providing and fixing Mineral Fibre Acoustical Suspended false Ceiling tile with washable metallized polyester foil backing and vinyl covered Edge in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. The tiles should have module size of 600 x 600 x 9mm.

Providing and applying 4 mm thick self levelling epoxy based resin Industrial flooring system. Work includes preparation of surface by diamond cutting machine to grind the floor and cutting the patches and cleaning the surface thoroughly & removing all the resides to leave a dry and dust free open tenured surfaces. Ist step : Applying of primer one (or) more coats and allow it to cure as per the requirement of site. IInd step : Applying of 2mm self levelling screed by using steel trowel and allow it to dry complete as per the requirement of site. IIIrd step : Applying of top coat with 2 mm epoxy self levelling topping with required colour/shade and allow it to dry etc ; to suit site condition. Further work includes miscellaneous repair / items as per the site requirement all as required to suit site conditions complete in all leads & lifts and all as directed by the Engineer-In-Charge.

Application/Laying of two or more coats with epoxy self-levelling topping strips for making the machines pathway of width 100 mm. complete all as required to suit site conditions in all leads & lifts and all as directed by the Engineer-In-Charge.

Electrical Items

MODULAR LT./FAN PT: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5sqmm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with angle pattern holder,modular switch, modular plate, suitable size GI. box and earthing the point with 1.5sqmm. FRLS PVC insulated copper conductor single core cable etc., as required.

THREE PHASE DB : Supplying and fixing of 6 way surface/recess mounting, horizontal type three pole and neutral, sheet steel, MCB distribution board,415V, on surface/recess, dust protected, duly powder painted, inclusive of 200A tinned cuppoer bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. 6 way (4+18), Double door

Single phase DB: Supplying and fixing following way, single pole and neutral, sheet steel, SPN MCB distribution board, 240Volts, on surface/ recess, complete with tinned suitable size copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required.(But without MCB/RCCB/Isolater) 6 way , Double door

SINGLE POLE MCB FOR DBs: Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections,testing and commissioning etc. as required. 16 amps to 32 amps Single pole

DOUBLE POLE MCB: Supplying and fixing 32 amps rating, 240/415 volts, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections,testing and commissioning etc. as required. 32 amps Double pole

TRIPLE POLE MCB: Supplying and fixing 32 amps rating, 415 volts, 16 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCCB DB complete with connections,testing and commissioning etc. as required. 32 amps Triple pole

ISOLATER: Supplying and fixing following rating, four pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

A.C. POINT: Supplying and fixing two modular G.I box per each socket & MCB with modular plate and cover in front on surface/recessed including providing and fixing 25A socket outlet and 25A modular SP MCB,"C" curve including connections, testing and commissioning etc.as required.

CIRCUIT WIRING : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

CIRCUIT WIRING : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

CIRCUIT WIRING : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

MODULAR 5A SWITCH : Supplying and fixing following modular switch(including indication lamp) on the existing modular plate & switch box including connections but modular plate etc. as required. 5/6 amp switch

MODULAR 5/6A SOCKET : Supplying and fixing following modular socket on the existing modular plate & switch box including connections but modular plate etc. as required. 3 pin 5/6 amp socket outlet

MODULAR 15/16A SOCKET : Supplying and fixing following modular socket on the existing modular plate & switch box including connections but modular plate etc. as required. 6 pin 15/16 amp socket outlet

MODULAR 15/16A SWITCH : Supplying and fixing following modular switch (suitable size/model) on the existing modular plate & switch box including connections but modular plate etc. as required. 15/16 amp switch

MODULAR BOX WITH COVER PLATE: Supplying and fixing of 2 Modules, G.I box alongwith modular base & cover plate for modular switches in recess etc. as required.

MODULAR BOX WITH COVER PLATE: Supplying and fixing of 6 Modules, G.I box alongwith modular base & cover plate for modular switches in recess etc. as required.

MODULAR BOX WITH COVER PLATE: Supplying and fixing of 12 Modules, G.I box alongwith modular base & cover plate for modular switches in recess etc. as required.

EXHAUST FAN LOUVER: Extra for fixing the louvers/shutters complete with frame for 300mm exhaust fan. As required.

EARTH WIRE: Providing and laying 6 SWG dia G.I wire on surface/recess for loop earthing as required.

EARTH STRIP: Providing and laying 25 x 5mm G.I strip on surface/recess and providing and fixing of G.I strip earth bus on surface or in recess for loop earthing as required.

EARTH PLATE: Earthing with G.I earth plate 600mm x 600mm x 6mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long, each termination should be with suitable 2 set of G.I bolt, nut & flat & spring washers of each run, testing earth resistivity of the Electrode and provision of 2'x2'x1' brick & cement chamber with 2'x2' RCC cover and including painting,marking of value etc. with charcoal/coke and salt as required.

HOT DIPPED G.I CABLE TRAY: Supplying and installing following size of perforated hot dipped G.I cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenent sections, joined with connectors, suitable support MS 'L' angles to wall with G.I bolts & nuts,etc. as required. 300 mm width x 50 mm depth x 1.0 mm thickness

FIXING OF DOWNROD IN TWIN LED TUBE LIGHT: Installation, testing and commissioning of prewired, Twin LED of all types, complete with all accessories etc.,including supplying and fixing ball and socket arrangement, 2no's.down rods of 20mm dia x 1.6mm thick steel conduit upto 200cm length, painting and wiring the down rods and connections with 1.5sqmm FRLS PVC insulated, copper conductor, single core cable and down rods fixing of top side suitable size MS angle/rod support hook, earthing etc.as required.

CABLE END BOX: Supplying and fixing of cable end box ( Loose wire box) suitable for following TPN Vertical type, sheet steel,MCCB distribution board,415V on surface/recess,complete with testing and commissioning etc.as required. For 6 way, Double door VTPN MCCB DB

CABLE END BOX: Supplying and fixing of cable end box ( Loose wire box) suitable for following TPN horizontal, sheet steel,MCB distribution board,415V on surface/recess,complete with testing and commissioning etc.as required. For 6 way,Double door TPN MCB DB

CABLE END BOX: Supplying and fixing of cable end box ( Loose wire box) suitable for following SPN horizontal, sheet steel,MCB distribution board, 230V on surface/recess,complete with testing and commissioning etc.as required. For 6 way,Double door SPN MCB DB

Ceiling Fan 1200mm: Supply, Installation, Testing and Commissioning of 1200mm sweep, BEE 5 star rated, Ceiling fan with Brush Less Direct Current(BLDC) Motor, Class of Insulation : B, 3 No's of blades, 30 cm to 150 cm long suitable size down rod and down rods fixing of top side suitable size MS angle/rod support hook, 2No's canopies, shackle kit, safety rope, copper winding, Power factor not less than 0.9, service value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min,350 RPM (tolerence as per Is:374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 deg C(max),insulation resistance morethan 2Mega ohm, suitable for 230V,50Hz, single phase AC supply, earthing etc complete as required.

CABLE END TERMINATION: Supplying and making end termination with brass compression gland and copper/aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. Upto 3 x 10 SQMM (22MM)

CABLE END TERMINATION: Supplying and making end termination with brass compression gland and copper/aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. Upto 4 x 10 SQMM (25MM)

CABLE END TERMINATION: Supplying and making end termination with brass compression gland and copper/aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 x 16 SQMM (28mm)

CABLE END TERMINATION: Supplying and making end termination with brass compression gland and copper/aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 x 25 SQMM (28mm)

CABLE END TERMINATION: Supplying and making end termination with brass compression gland and copper/aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ x 50 SQMM (35mm)

CABLE END TERMINATION: Supplying and making end termination with brass compression gland and copper/aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ x 120 SQMM (45mm)

CABLE END TERMINATION: Supplying and making end termination with brass compression gland and copper/aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ x 185 SQMM (57mm)

MV CABLE LAYING IN OPEN DUCT: Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry opn duct as required. UPTO 35 SQMM

MV CABLE LAYING IN OPEN DUCT: Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry opn duct as required. ABOVE 95 SQMM AND UPTO 185 SQMM

MV CABLE LAYING IN EXISTING PIPE: Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL/DWC pipe as required. UPTO 35 SQMM

MV CABLE LAYING IN EXISTING PIPE: Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL pipe as required. ABOVE 95 SQMM AND UPTO 185 SQMM

MV CABLE LAYING IN WALL: Laying and fixing of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size on wall surface as required.[cable will be supplied by deparment] Upto 35 sq.mm (clamped with 1mm thick saddle)

MV CABLE LAYING IN WALL: Laying and fixing of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size on wall surface as required.[cable will be supplied by deparment] ABOVE 35 SQMM AND Upto 95 sq.mm (clamped with 25X3mm MS flat clamp)

DWC HDPE PIPE LAYING in concrete flooring: Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc.conforming to IS 14930, Part II complete with fitting and cutting,jointing etc., in proposed concrete flooring complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal)

DWC HDPE PIPE LAYING: Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc.conforming to IS 14930, Part II complete with fitting and cutting,jointing etc.direct in ground (75cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc.,complete as required. 90 mm dia (OD-90 mm & ID-76 mm nominal)

SS Stand : Providing and fixing stainless steel ( Grade 304) stand for indistrial socket box made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishingand making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainlesssteel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge.

REMOVEL OF ELECTRICAL ITEMS: Removing the existing panel board's cable connection,wires, switch boards, light fittings, ceiling fans, & fixtures etc., and same to be hand over to Dept as directed by Engineer.

REMOVAL OF EXISTING OLD POWER PANEL: Removing of existing 3 phase Power panel and surface of wall/floor mounted & it incoming & outgoing's disconnecting the existing power cables connections without any damage and handed over to electrical division etc. The work also include providing temporary power supply to the essential existing loads as required.as directed by the site Engineer.

SUPPLYING AND FIXING OF EXHAUST FAN (450mm) : Supplying Installation and testing commissioning of 450mm Sweep 900rpm, heavy duty Exhaust fan complete with all accessories.. etc, fixing in the existing hole and fixing accessories including connections with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc., as required (The rate inclusive of required louver etc.,)

THREE PHASE DB (Vertical) : Supplying and fixing of 6way double door VTPN DB on surface/recess mounting, alongwith 4 pole 100A, 10kA, MCCB for incommer and out going MCB distribution board,sheet steel, 415V, on surface/recess, dust protected, duly powder painted, inclusive of 200A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs) as required. 6 way , Double door

SUPPLYING AND FIXING OF TWIN LED TUBE LIGHT FIXTURE : Supply, Installation, testing and commissioning of Pre-wired Twin LED 4 ft fitting 20W,230V complete with all accessories.. etc., directly mounted on existing down rods including connections with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc., as required.

MAKING HOLE FOR 450MM EXHAUST FAN: Making Exhaust fan holes in exisiting Brick/Rcc wall (Length up to 1 metre wall) with 450 dia mm exhaust fan, including good and finishing wall/brick etc., as per direction of enginner in charge.

MAIN PANEL BOARD: Supply, Installation, Testing & Commissioning of cubical pattern power distribution panel, modular compartmentalized, floor/wall mounted type with 40X6 mm thick MS angle frame , 3 phase and neutral MCCB power distribution board fabricated with suitable size, 14 SWG CRCA sheet powder coated/load/non-load bearings and earth bus consisting of the following as required: (a) Incomer:One chamber consisting of suitable size with mounting arrangements,supplying and fixing of 1no 4 pole 400A, 50kA FPMCCB (b) Out going MCCB: (i) 1 No. 250A, 36kA, 415 V, FPMCCB (ii) 1 No. 125A, 25kA, 415 V, FPMCCB (iii) 3 Nos. 63A, 16kA, 415 V, FPMCCB The above MCCBs should be mounted in individual chambers consisting of suitable size with mounting arrangements. (c) Suitable front operated handle in all MCCB's with auxillary contact and Suitable size copper bus bars chamber with insulated colour coded insulation along with 25x3mm copper earth bus for entire system. (d) Interconnection with suitable size insulated Copper link, provision of inscription labels etc. (e) Suitable cable chamber with knock out holes, terminal blocks, interconnection materials etc.as required. (f) 400/5A or suitable rating Current Transformer(cappa/AE/pragati) with Multifunction Metering arrangement and phase indicator lamps, Name Plate, etc.as required. Note: General arrangement drawing should be got approved before fabrication and including civil work for fountation bolt, nut & washers along with MS angle support as per site condition as required.

MAIN PANEL BOARD (NLP Plant): Supply, Installation, Testing & Commissioning of cubical pattern power distribution panel, modular compartmentalized, floor/wall mounted type with 40X6 mm thick MS angle frame , 3 phase and neutral MCCB power distribution board fabricated with suitable size, 14 SWG CRCA sheet powder coated/load/non-load bearings and earth bus consisting of the following as required: (a) Incomer:One chamber consisting of suitable size with mounting arrangements,supplying and fixing of 1no 4 pole 250A, 36kA FPMCCB (b) Out going MCCB: (i) 4 Nos. 100 A, 25kA, 415 V, FPMCCB (ii) 3 Nos. 63 A, 16kA, 415 V, FPMCCB The above MCCBs should be mounted in individual chambers consisting of suitable size with mounting arrangements. (c) Suitable front operated handle in all MCCB's with auxillary contact and Suitable size copper bus bars chambers with insulated colour coded insulation along with 25x3mm copper earth bus for entire system. (d) Interconnection with suitable size insulated copper link,provision of inscription labels etc. (e) Suitable cable chamber with knock out holes, terminal blocks, interconnection materials etc.as required. (f) 250/5A or suitable rating Current Transformer(cappa/AE/pragati) with Multifunction Metering arrangement and phase indicator lamps, Name Plate, etc.as required. Note: General arrangement drawing should be got approved before fabrication and including civil work for fountation bolt, nut & washers along with MS angle support as per site condition as required.

SUPPLY OF 3.5 x 120 SQ MM, ALUMINIUM ARMOURED CABLE: Supplying of 3.5 X 120 sqmm XLPE,sheathed and armoured aluminium conductor 650/1100V grade UG cable conforming to IS 7098(Pt-1)1988 and submit with necessry test certificate etc..,as required.

SUPPLY OF 3.5 x 150 SQ MM, ALUMINIUM ARMOURED CABLE: Supplying of 3.5 X 120 sqmm XLPE,sheathed and armoured aluminium conductor 650/1100V grade UG cable conforming to IS 7098(Pt-1)1988 and submit with necessry test certificate etc..,as required.

SUPPLY OF 3.5 x 50 SQ MM, ALUMINIUM ARMOURED CABLE: Supplying of 3.5 X 50 sqmm XLPE,sheathed and armoured aluminium conductor 650/1100V grade UG cable conforming to IS 7098(Pt-1)1988 and submit with necessry test certificate etc..,as required.

SUPPLY OF 4 x 25 SQ MM, ALUMINIUM ARMOURED CABLE: Supplying of 4 X 25 sqmm XLPE,sheathed and armoured aluminium conductor 650/1100V grade UG cable conforming to IS 7098(Pt-1)1988 and submit with necessry test certificate etc., as required.

SUPPLY OF 4 x 16 SQ MM, ALUMINIUM ARMOURED CABLE: Supplying of 4 X 16 sqmm XLPE,sheathed and armoured aluminium conductor 650/1100V grade UG cable conforming to IS 7098(Pt-1)1988 and submit with necessry test certificate etc., as required.

SUPPLY OF 4 x 2.5 SQ MM, COPPER ARMOURED CABLE: Supplying of 4 X 2.5 sqmm XLPE,sheathed and armoured copper conductor 650/1100V grade UG cable conforming to IS 7098(Pt-1)1988 and submit with necessry test certificate etc., as required.

SUPPLY OF 4 x 4 SQ MM, COPPER ARMOURED CABLE: Supplying of 4 X 4 sqmm XLPE,sheathed and armoured copper conductor 650/1100V grade UG cable conforming to IS 7098(Pt-1)1988 and submit with necessry test certificate etc., as required.

Making hole50mm in Wall : Making hole through wall & providing PVC pipe (50mm) for installation of AC outdoor unit pipe & cable by demolishing brick work manually and the same as good finishing of wall by plastering etc as required.

3 PIN INDUSTRIAL WITH PLUG: Supplying and fixing DP sheet steel enclosure on surface/recess in existing G.I tube/flat/wall alongwith 25/32A, 240V, "C" curve Double pole MCB with PVC SPN industrial type 3 pin socket outlet and industrial type with 3 Pin Plug including connection, earthing etc.as reqiured.

5 PIN INDUSTRIAL WITH PLUG: Supplying and fixing FP sheet steel enclosure on surface/recess in existing G.I tube/flat/wall alongwith 63A, 415V, "C" curve Four pole MCB with PVC SPN industrial type 5 pin socket outlet and industrial type 5 Pin Plug incloding connection, earthing etc.as reqiured.

SUPPLYING AND FIXING OF BLDC WALL MOUNT FAN (400mm) : Supplying Installation and testing commissioning of 400mm Sweep BLDC Wall Mounting fan complete with all accessories.. etc, fixing in the accessories including connections etc., as required.

LED PANEL LIGHT: Supply and fixing of Pre-wired ultra modern recess mounting LED panel light fitting, size of ceiling cutout 583 x 583mm, 36W/230V/6500K complete with all accessories etc., directly mounted on Gypsum/(2x2) false ceiling/ recess with suitable metal angle clamps including chain fixing, including earthing and connections etc., as required.

Buy Back Items

BUYBACK OF OLD POWER PANEL: Buy back of existing Old LT Panel consists of Switch fuse unit with individual compartment,Copper/Aluminium Busbars etc.