Civil work

Amount

SUB HEAD - I : EARTH WORK:

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. (a) All kinds of soil.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

(a) Ordinary rock.

(b) Hard rock (blasting prohibited).

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. (a) All kinds of soil.

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms,lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.

(a) Ordinary rock.

(b) Hard rock (blasting prohibited).

Credit of Hard rock

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with river sand under floors, including watering,ramming, consolidating and dressing complete.

Supply and filling good earth brought from out side MOD land filling in layer not exceeding 20 cm thickness at all height and depth including levelling, watering compaction etc. all complete (Deduct for 5% voids).

Drilling holein rock with required Dia. As Per Manufacture Specification - Cleaning by Air vaccum cleaner including at all height and level, scaffolding and grouting reinforcement bar with and according to Hilti RE 500 or Wuerth make PE-500 EPOXY CHEMICAL etc. all complete.

(a) 12 MM Dia. Hole 250 mm depth with RE-500 or PE-500 epoxy chemical of Hilti/Wuearth Make or Equivalent.

(b) 16 MM Dia. Hole 250 mm depth with RE-500 or PE-500 epoxy chemical of Hilti/Wuearth Make or Equivalent.

(c) 20 MM Dia. Hole 250 mm depth with RE-500 or PE-500 epoxy chemical of Hilti/Wuearth Make or Equivalent.

SUB HEAD - II : ANTI TERMITE TREATMENT WORK:

Supplying chemical emulsion in sealed containers including delivery as specified. (a) Chlorpyriphos/ Lindane emulsifiable concentrate of 20%.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : (a) Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.: (i) With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : (a) Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: (i) With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

SUB HEAD-III : PLAIN AND REINFORCED CEMENT CONCRETE WORK:

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

(a) 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size).

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses,parapets, coping, bed blocks, anchor blocks, plain window sills, fillets,sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing : a) 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately).

(a) All works upto plinth level.

(a) All works above plinth level upto floor V level.

Extra for Deduction of not pumping of concrete to site of laying.

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete,improve workability without impairing strength and durability as per direction of the Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum.Excess/less cement used as per design mix is payable/recoverable separately)

(a) All works upto plinth level.

(b) All works above plinth level upto floor V level.

Add / Deduct for using extra cement in the items of design mix over and above the specified cement content therein.

Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete. a)Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size) including Providing & applying a coat of DAMP PROOF membrane approved on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification ( per 50 kg cement).

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Centering and shuttering including strutting, propping etc. and removal of form for:

(a) Foundations, footings, bases of columns etc. for mass concrete.

(b) Walls (any thickness) including attached pilasters, butteresses,plinth and string courses etc.

(c) Suspended floors, roofs, landings, balconies and access platform.

(d) Lintels, beams, plinth beams, girders, bressumers and cantilevers

(e) Columns, Pillars, Piers, Abutments, Posts and Struts.

(f) Stairs, (excluding landings) except spiral-staircases.

(g) Weather shade, Chajjas, corbels etc., including edges.

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentring at all levels, over a height of 3.5 m, for every additional height of 1 meter or part thereof (Plan area to be measured). (a) Suspended floors, roofs, landing, beams and balconies (Plan area to be measured).

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm thick as per design for expansion joints. (a) 300 mm wide.

Providing and laying 40 mm wide expansion joints to roof as per details shown in the drawing and filling the same with filler board & back up rod of approved make and top 40 x 20 mm gap from finished surface shall be sealed with THIOFLEX 600 two part, polysulphide sealant, manufactured by Fosroc to BS 4254 :1983 after priming using Primer 7E. The Cost shall inclusive of sealant material, labour for necessary surface preparation, and application and excluding of filler board & back up rod.

SUB HEAD - IV : BRICK WORK:

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : (a) Cement mortar 1:6 (1 cement : 6 coarse sand.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: (a) Cement mortar 1:6 (1 cement : 6 coarse sand).

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : (a) Cement mortar 1:6 (1 cement : 6 coarse sand).

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement : 4 coarse sand) including Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. (a) Cement mortar 1:4 (1 cement : 4 coarse sand).

SUB HEAD - V : FINISHING:

Providing of 6mm cement plaster of mix in all surface with cement mortar 1:3 (1 cement : 3 fine sand) at all levels. .

Providing of 12 mm cement plaster of mix in all surface with Cement mortar 1:6 (1 cement : 6 fine sand) at all levels.

Providing of 15 mm cement plaster on the rough side of single or half brick / C.C wall of mix 1:6 (1 cement : 6 fine sand) at all levels.

Providing of 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

12 mm cement plaster finished with a floating coat of neat cement of mix 1:3 (1 cement: 3 fine sand).

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer Including with Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Finishing walls with water proofing cement paint of required shade : (a) New work (Two or more coats applied @ 3.84 kg/10 sqm.

Finishing walls with Acrylic Smooth exterior paint of required shade : (a) New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).

Applying priming coat:

With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works

Painting with synthetic enamel paint on Steel Body of approved brand and manufacture to give an even shade Two or more coats on new work.

Varnishing on Wooden Surface with varnish of approved brand and manufacture with Two or more coats of glue sizing with copal varnish over an under coat of flatting varnish including with French spirit polishing with Two or more coats on new works including a coat of wood filler.

Painting with synthetic enamel paint on Wooden Body of approved brand and manufacture to give an even shade with Two or more coats on new work.

Providing & fixing chicken wire mesh at the junctions of RCC and C.C , 200mm overlapping on both sides with all necessary hardware etc., complete with guage and mesh size - 20swg and 20mm mesh

SUB HEAD - VI : FLOORING WORK:

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Make of NITCO Company : Model name Exotica/Maxima series or ,Made of Somany Company : Model name Trecker/Sprinkler series or , Made of Kajaria Company : Model Name GaniliaCrema /Beige/Almono Made of Johnson /Equivalent.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. (a) 40 mm thick with 20 mm nominal size stone aggregate

52 mm thick cement concrete flooring with concrete hardener topping,under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. (a) 18 mm thick.

Extra for making chequers of approved pattern on cement concrete floors,steps, landing, pavements etc.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White,Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Make of NITCO Company : Model name Exotica/Maxima series or ,Made of Somany Company : Model name Trecker/Sprinkler series or , Made of Kajaria Company : Model Name GaniliaCrema /Beige/Almono Made of Johnson /Equivalent.

Providing and laying Double Charged vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Made of NITCO Company :Model name -Bermuda or Made of Somany ompany :Model name Celestial /Elegance series or Made of Kajaria company :Model name Super Glossy Nanotech K-6016/6018/6019/6101/6012 & Jhonson Make : Quarzet DK & Quarzet HL Or Equivalent a) Size of Tile 600x600 mm.

Providing and laying Double Charged Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), including routing the joint with white cement & matching pigments etc. Made of NITCO Company :Model name -Bermuda or Made of Somany ompany :Model name Celestial /Elegance series or Made of Kajaria company :Model name Super Glossy Nanotech K-6016/6018/6019/6101/6012 , Jhonson Make : Quarzet DK & Quarzet HL Or Equivalent. (a) Size of Tile 600x600 mm.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : (a) Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. (a) Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Proving and Laying Vaccum dewatered cement concrete 1:1.5:3(1 cement ;1.5 coarse sand and 3 graded aggregate of 20mm)flooring in alternate panels of 3x4m including reinforcement 8mm at 200 c/c .Vaccum dewatered technic to accelerate the evaporation of excess water in green concrete using rigid or flexible suction mat incorporating filter layer and vaccum generators (80 to 90% vaccum to be applied at the rate of 3 to 5 minute per 25mm depth ) all as per specification including cutting grooves 4mmx20mm deep in flooring with diamond saw cutting machine before the concrete is seven days old including providing and filling the grooves with polysulphate sealant of approved make or equivalent (modified semi rigid epoxy joint filler ) including cost of required the panel shuttering work with steel channel and as per direction of Engineer-In- charge.The work shall be carried out by specialist agency approved by Engineer -in charge

Anti static Flooring : Preparing the concrete floor surface using captive shot blasting machine .Cut open all construction joints to fill with epoxy putty using Nitocote VF or Equivalent .Same treatment will be carried out to treat shrinkage joints.Providing and laying one coat of Nitoprime 25 or equivalent .Providing and applying Nitoflor SL or equivalent conductive undercoat and overcoated with Notoflor SL or equivalent conduvtive top coat in 2mm thick over primed surface at 7.5 sq mt per pack and finishing as per Forsroc specification .When measured for surface resistance in accordance with BS2050:1978 (A-1984) and DIN EN 1081 ,the static conductive topping including under coat shall be in range of 50-1000 K ohms . When tested for static decay as per Federal test method 101B ,Method 4046, the static conductive tppic shall take not more than a time of 0.01 seconds to decay with +5KV peak charge to 0% .The surface resistance of the conductive undercoat shall be in the range of 3-9 K ohms .Note : Copper strip will be provided to connet earthing point for safe discharge of charges .Make : Forsroc or Equivalent.

Providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing to edges to give high gloss finish etc. complete at all levels. a) Granite of any colour and shade. i) Area of slab over 0.50 sqm.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc.complete as per design approved by Engineer-in-Charge. a) Granite work.

Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. (a) Granite Stone of approved shade.

SUB HEAD - VII : WOOD WORK / ALUMINIUM WORK :

Providing and fixing pressed steel door frames conforming to IS: 4351,manufactured from commercial mild steel sheet of 1.60 mm thickness, including jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm,pressed mild steel welded or rigidly fixed together by mechanical means, with mortar guards,lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: a) Profile C - 125 X 60 X 1.6 mm i) Fixing with adjustable lugs with split end tail to each jamb.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. (a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws including Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters.

Extra for Not Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete : (a) 125 x 64 x 2.5 mm.

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness .The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat.Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

Providing and fixing : (a) 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/ Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : a) For fixed portion. i) Powder coated aluminium (minimum thickness of powder coating 50 micron):

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) a) Powder coated aluminium (minimum thickness of powder coating 50 micron).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

(a) With float glass panes of 5.50 mm thickness.

(b) With Tinted Glass panes of 6 mm Thickness.

(c) With Toughned Glass of 12 mm Thick..

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. (a) Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868),transparent or dyed to required colour or shade, with nuts and screws etc. complete : (a) 300x16 mm.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : a) 150x10 mm.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : a) 125 mm.

Providing and fixing aluminium hanging floor door stopper, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. a) Twin rubber stopper.

Providing and fixing of rubber nylon door buffer (dia of 40mm and 50mm long) on wall with rowl plug and screw.

Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : (a) 300x16 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish,(Barrel type) with necessary screws etc. complete : (a)150x10 mm.

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : (a)100 mm.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge.

Providing and fixing of Galvanized steel flush doors of Shakti-Met-Dor Ltd make or equivalent. The door frame shall be single rebate profile of size 100 X 57 mm made out of 1.60 mm thick galvanized steel. The shutter shall be 45 mm thick fully flush made out of 1.20 mm thick galvanized steel both sides, unfill material shall be resin bonded honey comb craft paper for rigidity and sound insulations. Door frames and shutters shall be finished with two coats of epoxy zinc phosphate primer and finished paint shall be in polyurethane aliphatic grade for superior addition, scratch resistant etc. Inclusive of approval of shop drawings, gaskets & all other hardware etc.all complete. (a) Above 3.0 m and upto 6.0 m height.

SUB HEAD - VIII : STEEL WORK:

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Structural steel work riveted, bolted or welded in built up sections,trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Supply febrication and erection members like purlins, side runner etc., made of cold formed galvanized C and Z sections with available thickness 1.6mm, 1.8mm, 2.0mm, 2.5mm, of strangth (345 Mpa) and galvanised for not less than 275 GSM etc., all complete.

Supplying , transporting to site and erecting plate -factory fabricated pre - Engineered Building (PEB ) including submission of shop drawings for approval, including all the materials required at site, columns , girders bracing members etc shown in the drawings and with necessory acessories, sand blasting applying one coat of zinc chromate primer and two coats of synthetic enamel paint all as directed by engineer-in-charge. steel shall be high grade of strength not less than 345 MPa.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. (a) Using M.S. angels 40x40x6 mm for diagonal braces.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. (a) 80x0.90 mm M.S. laths with 0.90 mm thick top cover.

Providing and fixing ball bearing for rolling shutters.

Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer-in- charge, (area of grill to be measured).

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

SUB HEAD - IX : ROOFING & WATER PROOFING:

Supplying and fixing of precoated Zincalume / Galvalume sheet roofing of 0.5mm TCT -AZ-150, 550 mpa (Alumunium Zinc Alloy coating of 150 gms, per sqm total on both sides) as per AS: 1397 in cover width of 1000-1020 mm, (size, shape and pitch of corrugation as approved by Engineer-in-charge).The end rib shall be designed for anti-capillary action, to avoid any seepage of water through the lateral overlap. The feed material is manufactured out of nominal 0.45 mm Base Metal Thickness (BMT), Hi-strength steel with min. 550 MPa yield strength. The steel sheet shall be fastened with 25 μm zinc-tin alloy coated, Hex head, self-drilling screw as per AS 3566-2002 Class 3 fasteners of approved make with EPDM washer as per the requirement considering the profile shape and design load. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12meter or as directed by Engineer-in-charge.(Make : Tata or Equivalent)

Supply and Fixing of Mechanically strong, impact resistant, light weight, weather proof and fire resistant ‘Rhino Tuff’ ‘U.V. Coated Polycarbonate Multi-Wall Sheet in any size as per requirement and in a thickness of 8.0 mm. The Sheets are provided with a protective U.V. Coating both side to guard against the harmful U.V. Rays of Sun. The Sheets are also provided with a protective P.E. Film on both sides to guard against any damage in the course of handling or transporting the P.C. Sheets.

Supply and Fixing of Turbo Jet Roof Ventilation with Specification , Effective Throatal - 24" , Ventilator Outer Dia. - 30" Overall Height - 19" , all Complete

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre,shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I.

wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills,diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : (a)12.5 mm thick tapered edge gypsum moisture resistant board. (Make : Gproc , L Strong , Armstrong)

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.

Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. (a)12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/ sqm).

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs,balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : (i) With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (a) 110 mm diameter.

SUB HEAD - X : SANITARY INSTALLATIONS WORK:

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : (Make: JAQUAR , SOLO SERIES , Modle No.: SLS-WHT-6751P for W.C & SLS-WHT-6201 for Flushing Cistern).

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern,with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass,including painting of fittings and cutting and making good the walls and floors wherever required : (a) Single half stall urinal with 5 litre P.V.C. automatic flushing cistern.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: (a) White Vitreous China Table Top Basin (JAQUAR Cat. No. -FLS-WHT-0539.

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in- charge.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing toilet paper holder : (a) C.P. brass.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. (a) 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : (a) 15 mm nominal bore (Make : Jaquar , Model No, - CON-037KN)

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. (a) 15 mm nominal bore. (Make : Jaquar , Model No, - CON-107KN)

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. (a)15 mm nominal bore.

Providing and fixing S.S. grating, including setting in floor with cement mortar 1:3. with all complete as per direction of Engineer - in - Charge. (Make: KINGSTON , Accessories Series, Modle No.: AGR-ACS-39 or Equivalent).

Providing and Fixing Health Faucet Jaquar Cat. No. 573 (Allied Series) or equivalent make Kingston-AGR ACS 49, KOHLER Cat. No. 12925IN-CP (HEALTH FAUCET W/WHITE SDSPRAY, M HOSE) with flexible pipe and wall hook with each European W.C. Pan.

SUBHEAD - XI : WATER SUPPLY:

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall

(a) 20 mm outer dia pipes

(b) 25 mm outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

(a) 15 mm nominal outer dia Pipes

(b) 20 mm nominal outer dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External Work

(a) 25mm nominal outer dia pipes

(b) 40mm nominal outer dia pipes

(c) 65 mm nominal inner dia Pipes

(d) 80mm nominal outer dia pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

(a) 25 mm nominal bore.

(b) 32 mm nominal bore.

(c) 40 mm nominal bore

(d) 65 mm nominal bore

(e) 80 mm nominal bore

Providing and fixing ball (brass) valve of approved quality. High or low pressure, with plastic floats complete: (a) 25 mm nominal bore

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : (a) With common burnt clay F.P.S (non modular) bricks of class designation 7.5.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. (a) Circular tank.

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : (a) With common burnt clay F.P.S (non modular) bricks of class designation 7.5.

Providing & fixing BUTTERFLY VALVE with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/hot water circulation as specified (a) 80 mm dia

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber, insertions etc. complete (The tail pieces, tapers etc if required will be paid separately). (a) 50 mm dia.

Providing and fixing in position C.I 560 mm dia cover with frame (Heavy duty) manhole cover of approved quality . Circular shape 560 mm internal dia.

SUBHEAD - XII : SOIL WASTE AND VENT PIPE AND FITTINGS WORK:

Providing and fixing SWR uPVC pipes (Type-B) confirming to IS 13592 : 1992 complete with all fittings e.g. plain or door bends, junctions, cowls, offsets, access pieces etc. jointing with rubber rings and solvent cement including fixing the pipes on wall face with MS galvanized holder bat clamps or suspended below ceiling with MS galvanized hangers/supports and fasteners all as approved by the engineer in charge including Cutting holes in walls, floors excavation, refilling and disposal of surplus earth wherever required and making good . The rates shall be inclusive of painting of all supports and clamps with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation.(Sample of holder bat clamps,hangers / supports to be approved by the Engineer-in-Charge.) (a) 110 mm dia.

Providing and fixing uPVC deep seal 'P' or 'S' / Nahani trap of self cleansing design with or without vent arm with provision for connecting uPVC inlet fitting complete including cost of cutting and making good the walls and floors wherever required. (a) For 110mm inlet and 80mm outlet.

Providing and fixing uPVC threaded waste pipes (I.S:4985-2000) Class - 6 including all fittings e.g bends, junctions, elbows, tees, offsets etc. jointing with screwed joints including cutting holes in walls, floors excavation, refilling and disposal of surplus earth wherever required and making good.

(a) 32 mm nominal bore.

(b) 50 mm nominal bore.

(c) 80 mm nominal bore.

SUB HEAD -XIII : INTERNAL ELECTRIFICATION WORK:

LIGHT POINTS: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (a) Group - C

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. (a) Group - C

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. a) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (a) 4 X 10 sq.mm + 2 X 6 sq.mm earth wire

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (a) 4 way (4 + 12), Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) a) 8 way (4 + 24), Double door

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) 40 A

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) Single pole

Supply of the following Light Fixture with lamp, Control Gear & All necessary accessories. Luminaries with all electrical accessories & it should be energy efficient, low loss, ortho cyclically wound open construction copper ballast, ignitor & power factor improvement capacitor or Electronics Ballast etc are prewired to the terminal block & mounted on are movable control gear module for ease of maintenance. All electrical connections of the control gear module with the rest of the luminaries should be click fix & require use of no tools. Mounting options should be for both lateral as well as pole top mounting. with Lamp Control Gear & Fixing Accessories.

(a) 20W LED Surface Type Light Fixture (Make: Wipro cat no LL20-221-XXX-65AL1 or Eqivalent)

(b) 2x20W LED Surface Type Light Fixture (Make: Wipro cat no WIO922208 + 2* LL13-181-65SE or Eqivalent)

(c) 2'x2' LED Recessed Type Light Fixture (Make: Wipro cat no CRCO10R038HP57G1 or Eqivalent)

(d) 18 W LED Ceiling Light Fixture Recessed Type (Make: Philips Cat No. DN195B LED20S-6500 PSU WH S1 Wipro cat no CRDL11R023HP57 or Eqivalent)

(e)15W LED Ceiling Light Fixture Surface Type (Make: Wpro cat no `LD99-211-XXX57SMWH or Eqivalent)

(f) 15W LED Ceiling Light Fixture Recessed Type (Make: Wipro cat no LD71-161-SML-65-XX** or Eqivalent)

(g) LED Highway Light (Make: Regent Cat No.LED 3664-Hogvik-150w / Wipro cat no LH14-192-XXX-57-G2 or Eqivalent)

(h) 1 x 10W LED Bulk Head Light Fixture Make: Wipro cat no LW07-141-XXX-57-XX or Eqivalent)

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Supply of ceiling fan of 1200mm sweep ( white colour) suitable for operation on 230/240V, 50Hz, single phase, AC Supply complete with double ball bearing motor, required down rod, capacitor, three MS blades etc complete. (5 Star Rating)

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Supply, Installation & testing of 400mm wall bracket fan suitable for use on single phase, 230 volt, 50Hz AC supply complete with all accessories as required

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supply, Installation & testing of 400mm pedestal fan suitable for use on single phase, 230 volt, 50Hz AC supply complete with all accessories as required

Supply of following 900 RPM Exhaust fan non metalic suitable for single phase 230/240V, AC Supply complete with motor louvers , mounting brackets, all accessories etc complete as required. a) 300mm dia

Supply of following 900 RPM heavy duty Exhaust fan suitable for single phase 230/240V, AC Supply complete with motor MS louvers , mounting brackets, all accessories etc complete as required. a) 300 mm dia

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. (a) Upto 450 mm sweep

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

SUB HEAD-XIV : POWER WIRING:

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (a) 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (a) 4 X 6 sq. mm + 2 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (a) 4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (a) 4 way (4 + 12), Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (a) 6 way (4+18) double door (Horizontal type)

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) 63 A

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) Single pole

Supply, installation, Testing and Commissioning of 3 phase and Neutral 415V 4 wire Free Standing Floor mounted indoor MV panel made out of 14 SWG MS sheet after seven tank process and painting with Epoxy powder coating. The panel shall consist of suitable rating TPN Aluminium bus bar (at the rating of 0.8A/Sq.mm) supported with DMC / SMC barriers and color coded with Heat shrinkable sleeves. The Metering shall be provided as specified. The panel shall have short circuit withstanding capacity of minimum 35KA and consist of the switchgear as mentioned below. The panel shall be got fabricated from manufacturer with CPRI Test certificate only. The PCC shall have at least two spare cubicles of the maximum rating. The size of all Panel Mounting Meters shall be 96X96mm. The Panels shall be mounted on U channels including supply and fixing of the same.

SUB HEAD - XV: UPS WIRING:

Supplying and fixing 6 module (200mm x75mm) GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. 3 pin 5/6A modular socket outlet and 1 no. 15/16A modular switch, connection, painting etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (a) 2 X 2.5 sq.mm +1 X 2.5 sq.mm Earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (a) 2 X 10 sq.mm + 1 X 6 sq.mm earth wire

Supplying and fixing following way, single pole and neutral,sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earthbar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (a) 12 way , Double door.

Supplying and fixing following rating, double pole, (single phaseand neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.. (a) 40 A

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) Single pole

UPS PANEL-2 (UPS) INCOMING : 63 Amp DP (10KA) miniature circuit breaker.- 1 No. BUSBAR: 100 Amp. DP CU. Busbar. OUTGOING : 40 Amp DP (10KA) Miniature circuit breaker - 4 Nos

SUB HEAD -XVI : SHOP ELECTRICALS:

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 63 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 63 A, “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

(a) 100 A, 25KA,FP Moulded case circuit breaker with operating handle.

(b) 160 A, 25KA,FP Moulded case circuit breaker with operating handle.

(c) 250 A,36KA,FP Moulded case circuit breaker with operating handle.

(d) 400 A, 36KA, FP Moulded case circuit breaker with operating handle.

Supplying and fixing of metal one way sheet steel enclosure for FP MCCB Suitable for 100A and 160A complete with connections, testing and commissioning etc. as required.

Supplying and fixing of metal one way sheet steel enclosure for FP MCCB Suitable for 250A complete with connections, testing and commissioning etc. as required.

Supplying and fixing of metal one way sheet steel enclosure for FP MCCB Suitable for 400A complete with connections, testing and commissioning etc. as required.

Supplying of XLPE insulated, PVC sheathed 1.1 KV grade aluminium conductor armoured power cable as per IS : 7098 of following sizes:

(a) 3.5 core 240 sq. mm.

(b) 3.5 core 120 sq. mm.

(c) 3.5 core 70 sq. mm.

(d) 3.5 core 35 sq. mm.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.

(a) Upto 35 sq. mm

(b) Above 35 sq. mm and upto 95 sq. mm

(c) Above 95 sq. mm and upto 185 sq. mm

(d) Above 185 sq. mm and upto 400 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

(a) 3.5 core 240 sq. mm.

(b) 3.5 core 120 sq. mm.

(c) 3.5 core 70 sq. mm.

(d) 3.5 core 35 sq. mm.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

(a) 150 mm width X 50 mm depth X 1.6 mm thickness

(b) 300 mm width X 50 mm depth X 1.6 mm thickness

Supply, installation, Testing and Commissioning of 3 phase and Neutral 415V 4 wire Free Standing Floor mounted indoor MV panel made out of 14 SWG MS sheet after seven tank process and painting with Epoxy powder coating. The panel shall consist of suitable rating TPN Aluminium bus bar (at the rating of 0.8A/Sq.mm) supported with DMC/ SMC barriers and color coded with Heat shrinkable sleeves. The Metering shall be provided as specified. The panel shall have short circuit withstanding capacity of minimum 50KA and consist of the switchgear as mentioned below. The panel shall be got fabricated from manufacturer with CPRI Test certificate only. The PCC shall have at least two spare cubicles of the maximum rating. The size of all Panel Mounting Meters shall be 96X96mm. The Panels shall be mounted on U channels including supply and fixing of the same.

Busbars : 1000A TPN Aluminium Busbar-1set Outgoings : 3 Nos 160 Amp 4P (25KA)moulded case circuit breaker with operating handle. 6 Nos 100 Amp 4P (25KA) moulded case circuit breaker with operating handle. 10 Nos 63 Amp 4P (10KA) Miniature circuit breaker.

Busbars : 2500A TPN Aluminium Busbar-1set Outgoings : 4 Nos 400 Amp 4P (25KA) moulded case circuit breaker with operating handle. 3nos 250 Amp 4P (25KA) moulded case circuit breaker with operating handle. 2nos 160 Amp 4P (25KA) moulded case circuit breaker with operating handle. 1no 100 Amp 4P (25KA) moulded case circuit breaker with operating handle. 10 nos 63 Amp 4P (10KA) Miniature circuit breaker.

Busbars : 800A TPN Aluminium Busbar-1set Outgoings : 3 Nos 160 Amp 4P (25KA) moulded case circuit breaker with operating handle. 4nos 100 Amp 4P (25KA) moulded case circuit breaker with operating handle. 10 nos 63 Amp 4P (10KA) Miniature circuit breaker.

Busbars: 500A TPN Aluminium Busbar-1set Outgoings : 5 Nos 100 Amp 4P (25KA) moulded case circuit breaker with operating handle. 10 nos 63 Amp 4P (10KA) Miniature circuit breaker.

Busbars : 315A TPN Aluminium Busbar-1set Outgoings : 3 Nos 100 Amp 4P (25KA) moulded case circuit breaker with operating handle. 10 nos 63 Amp 4P (10KA) Miniature circuit breaker.

Busbars: 315A TPN Aluminium Busbar-1set Outgoings: 4 Nos 100 Amp 4P (25KA) moulded case circuit breaker with operating handle. 10 nos 63 Amp 4P (10KA) Miniature circuit breaker.

SUB HEAD -XVII : TELEPHONE / TV / LAN CONDUITING:

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. (for Telephones, TV and Data) (a) 25 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. (for Telephones, TV and Data) (a) 32 mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. (a) Telephone socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. (a) TV antenna socket outlet

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. (a) 1 or 2 Module (75 mmX75 mm)

Supply and fixing of Data outlet (RJ45) with anodised GI box with front plate etc. complete as required

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. (a) 2 Pair

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. (a) 10 Pair

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. (a) 50 Pair

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supply and installation of following size Krone connectors in MS box complete as required. (a) 20 Pair

Supply and installation of following size Krone connectors in MS box complete as required. (a) 100 Pair

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (60 cm deep) and re-filling etc. as required (a) 80 mm dia

SUB HEAD -XVIII : SPECIAL EARTHING:

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

SUB HEAD -XIX : LIGHTNING PROTECTION:

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or on surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or on surface of wall for lightning conductor complete as required. (For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 Nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

SUB HEAD -XX : EXTERNAL POWER SUPPLY:

Flywheel, flexible coupling, air cleaner, corrosion resistor, Radiator, fan with guard, Fuel pump,fuel filter, Electronic governor, starting system with separate Battery charger with 2nos 24Vsealed Maintenance Free Batteries, Voltageregulator, Instrument panel with RPM Indicator, Exhuast silencer (hospital), protections against Low Lub.oil pressure,highwater temperature and with suitable capacity fueltank, fuel lines from Fuel tank to DG set,battery stand, anti vibration pads and first filling of lubricating oil and fuel oil for set. The Alternator shall be suitable for415V 3phase, 4wire, 50HZ AC supply operation and shall be able to deliver full load current at 20% Unbalance load.As per CPCB approved.

Supply and installation of 990Ltrs capacity Fuel tank made out of MS sheet with Inlet/ Outlet connecting pipes, plugs, Drain valve from DG sets to tank and Scale with level monitoring.

Supply and Fixing of MS Exhaust Pipe of 300mm dia cladded with 50mm thick Glasswool insulation covered with 24SWG Aluminium sheet.

Supply, Receiving, Unloading, Shifting, Installation Testing & Commissioning of indoor type 11 KV Single Breaker Vacuum Circuit Breaker Panel Board as 1 Incomming / Outgoing shall be metal clad floor mounting complete as per specification and as described. Manually and motor operated, spring charged (release closing mechanism) trip free type,triple pole truck mounted draw out, vacuum circuit breaker, incorporating mechanical as well as electrical ON/OFF indication. Spring charge/discharge mechanical indication"OFF" push buttons for emergency trip (shrouded) test/service position limit switches with 6 NO/6 NC breaker auxilliary contacts in service position, 24 Volts DC shunt trip coil and strip heater to prevent moisture absorption.

1 Set of following indicating lamps. Red, Yellow & Blue for phase indication. Amber for Trip indication. Red `ON' Green `OFF'. Spring charge indication. Auto trip indication. 1 No. hooter with hooter acceptance and reset push button. 1 No. master trip relay. ( Electromechanical Type ). 1 No.Trip ckt supervision relay. (Electromechanical Type ). 600A color coded heat shrinkable sleeved TP Copper busbar of 350 MVA fault rating. 1 Set of fuses, ferrules, wiring etc. as required. 1 Set of Power Pack 220 Volt A.C. / 24 Volt D.C. complete as required. 1 No. control Transformer of 1KVA for giving supply to indication lamps etc having 11 KV/415-230V AC rating epoxy cast resin dry type Transformer. The connection for control transformer shall be taken from the cable side before the circuit breaker tapping.

Note: All spare contacts of breaker or any other equipment inside the breaker shall be wired upto the outgoing terminal strip with appropriate ferrules / coding. The terminal strip rating shall be suitable for connecting two wires of 2.5sqmm subjected to providing minimum size strip suitable for 4/6sqmm.

Design, manufacture, supply, installation, testing and commissioning of 1600 KVA, 11 KV /0.415 KV, 3 phase, 6.25 % impedance, 50 Hz delta/star-11 connected, outdoor type, copper wound transformer, oil immersed ONAN cooled, complete with all fittings such as oil conservator, silica gel breather, thermometer, explosion vent with on Load Tap changing (OLTC) arrangement on HV side with Tapping for variations of high voltage from (+) 5% to (-) 15% in steps of 1.25% each with integrated microprocessor based RTCC Panel, bi-directional roller, diagrams & rating plate, Oil temperature indicator, & Winding temperature indicator, Buchholz relay, weather proof Marshalling Box, lifting lugs, first filling of oil, weather proof H.T/L.T cable box etc. complete as per specification. All relays, contacts & CT terminals to be wired upto marshalling box. The Transformer losses should confirm to IS - 1180 Part-1 (2014) with energy efficiency level 2 [4.20 KW at 50% load & 11.8 KW at 100% load shall not exceeds by 5.0% (@ 11 KV) of the maximum total loss values. a) 1600KVA

Design, Manufacturing, Supply, Receiving, Unloading, Shifting, Installation, Testing & commissioning of Main L.T. Panel Cum Synchronizing Panel with Micro PLC / relay control, this will be floor mounted, free standing, compartmentalized, indoor duty, dust proof, vermin proof, front operated, electrical panel fabricated, painted and manufactured exactly as per specifications laid in this document and will be complete with the main and auxiliary bus bars, interconnection, earth terminals, earth bus and will be powdered coated finished. All the busbar joint shall be protected by clip on type sleeve. The control panel shall use all draw out 3 position withdrawn type breakers suitable for 415 V AC, 3 phase, 50 Hz, 4 wire supply system and will have fault level of 35 KA or as required as per consultant approval. The panel will be made as per detailed specifications and drawings forming part of this document.The current density of main bus bar & drooper bus bar up to 1000 Amp shall be minimum 1.00 sq mm / amp & for 1250 / 1600 amp shall be minimum 1.30 sq.mm / amp.& for 2000 / 2500 / 3200 amp shall be minimum 1.60 sq.mm / amp

Each Incoming / Outgoing Air Circuit Breaker Breaker shall have microprocessor release with adjustable over current, short circuit & earth fault protection with instantaneous as mentioned in specification. The Panel will be made as per detailed specifications & drawings forming part of this document. Fault level of panel shall be 50 KA. Each Bus Coupler Air Circuit Breaker shall be with inbuilt U/V release. The Panel will be made as per detailed specifications & drawings forming part of this document. Fault level of panel shall be 50 KA. Each Outgoing MCCB shall have thermal release with adjustable over current, short circuit & eartg fault protection (Inbuilt / External module) up to 250 Amp and above shall have microprocessor release with adustable overload, short circuit & earth fault protection. (Ics shall be 35 KA).

INCOMING: 1 Nos. 2500 Amp FP Electrically operated horizontal drawout type Air Circuit Breaker. 2 Nos. 1250 Amp FP Electrically operated horizontal drawout type Air Circuit Breaker. BUSCOUPLER: 21 No. 1250 Amp FP Electrically operated horizontal drawout type Air Circuit Breaker as buscoupler. AUTO OPERATION OF INCOMER / BUSCOUPLER ACB's. Micro PLC / relay control shall be provided to achieve the following functions. Auto changeover. Auto synchronization & Load management. Buscoupler switching. Interlocking. Automatic system shall be user friendly and shall have manual override.

BUSBARS: 2500 Amp TPN busbars of aluminium alloy as per SLD. OUTGOING: (EACH OUTGOING FEEDER SHALL HAVE DUAL SOURCE DIGITAL ENERGY METER.) 02 Nos 1600 Amp TPN MDO Air Circuit Breaker (50 KA). 01 No 800 Amp TPN MDO Air Circuit Breaker (50 KA) 02 Nos 630 Amp TPN Moulded Case Circuit Breaker(35KA) 03 Nos 400 Amp TPN Moulded Case Circuit Breaker(35KA) 03 Nos 400 Amp TPN Moulded Case Circuit Breaker(35KA) 03 Nos 250 Amp TPN Moulded Case Circuit Breaker(35KA) 01 Nos 200 Amp TPN Moulded Case Circuit Breaker(35KA) 09 Nos 100 Amp TPN Moulded Case Circuit Breaker(35KA) 03 Nos 63 Amp TPN Moulded Case Circuit Breaker(35KA)

APFC PANEL - 650 KVAR: Incoming : 1 Nos. Digital Multifunction Meter with CT's. Metering : 1 Sets of phase indicating lights (RYB) with protection MCB's. 1 Sets breaker 'ON' & 'OFF' indicating lamp. 16 Step Automatic Power Factor Correction relay (APFC relay). BUSBARS 2000 Amp TPN busbars of aluminium alloy as per SLD.

OUTGOING: Outgoings : 02 Nos. 250 Amp TP MCCB (35 KA) with capacitor duty contactor with 14% detuned reactor (one for each 100KVAR capacitor unit). 07 Nos. 125 Amp TP MCCB (35 KA) with capacitor duty contactor with 14% detuned reactor (one for each 50KVAR capacitor unit). 03 Nos. 63 Amp TP MCCB (35 KA) with capacitor duty contactor with 14% detuned reactor (one for each 25KVAR capacitor unit). 02 Nos. 32 Amp TP MCCB (35 KA) capacitor duty contactor with 14% detuned reactor (one for each 10KVAR capacitor unit). 01 Nos. 16 Amp TP MCCB (35 KA) capacitor duty contactor with 14% detuned reactor (one for each 5KVAR capacitor unit).

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

(a) Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

(b) Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

(c) Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 50 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Supply and laying of 11KV grade Rubber Mats as per IS 15652 of size1000mm x 2000mm

Supply and fixing of 4 nos fire bucket painted red and duly filled with MS sand complete as required. conforming to IS:2546-1974.

Supplying and fixing of shock restoration chart written in English and Hindi duly framed in glass as required.

Supplying and fixing carbon dioxide fire extinguisher type 4.5 Kg. capacity of approved make wall mounting bracket as required conforming to IS;2878/1976.

Supplying of first aid box as approved complete with standard kit as prescribed by Indian Red Cross.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supply of Hand Gloves -11KV grade

Supplying of XLPE insulated and PVC sheathed 1100V armoured copper conductor control cable as required. (a) 4 x 1.5 Sqmm

Supplying of XLPE insulated and PVC sheathed 1100V armoured copper conductor control cable as required. (a) 10 x 1.5 Sqmm

Supplying of XLPE insulated and PVC sheathed 1100V armoured copper conductor control cable as required. (a) 14 x 1.5 Sqmm

Supplying of following size aluminium conductor XLPE 11 KV (E) cable complete as required. The cable shall conform to IS : 7098/ Part II (a) 3C x 240 Sqmm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. (a) Above 120 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. (a) Above 120 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonry open duct as required. (a) Above 120 sq. mm and upto 400 sq. mm

Supplying and making indoor cable end jointing with cast resin compound, including lugs and other jointing materials, for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : (a) 3C x 240 Sqmm

Supplying of XLPE insulated, PVC sheathed 1.1 KV grade aluminium conductor armoured power cable as per IS : 7098 of following sizes:

(a) 3.5 core 400 sq. mm.

(b) 3.5 core 300 sq. mm.

(c) 3.5 core 240 sq. mm.

(d) 3.5 core 185 sq. mm.

(e) 3.5 core 150 sq. mm.

(f) 3.5 core 95 sq. mm.

(g) 3.5 core 70 sq. mm.

(h) 3.5 core 35 sq. mm.

(i) 4 core 16 sq. mm.

(j) 2 core 6 sq. mm.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. (a) Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

(a) Upto 35 sq. mm

(b) Above 35 sq. mm and upto 95 sq. mm

(c) Above 95 sq. mm and upto 185 sq. mm

(d) Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. (a) Above 185 sq. mm and upto 400 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

(a) 3.5 core 400 sq. mm.

(b) 3.5 core 300 sq. mm.

(c) 3.5 core 240 sq. mm.

(d) 3.5 core 185 sq. mm.

(e) 3.5 core 150 sq. mm.

(f) 3.5 core 95 sq. mm.

(g) 3.5 core 70 sq. mm.

(h) 3.5 core 35 sq. mm.

(i) 4 core 16 sq. mm.

(j) 2 core 6 sq. mm.

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. (a) 100mm dia

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. (a) 150 mm dia

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. (a) 300 mm dia

SUB HEAD - XXI : FIRE ALARM SYSTEM:

Supplying, installation, testing & commissioning of addressable beam detector with short circuit isolator (inbuilt) or seperate) complete with emitter and receiver including connections with remote test features etc complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector acclimate type sensetive level (0.524%) OVS/ft. complete with mounting base complete as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. (75 DBA @3 mtr. & 75CD flashing)

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

Supply, fixing and installation of fire exit signage's self illuminating light fixtures displaying exit with an arrow towards the exit door.

SUB HEAD - XX : HVAC WORK:

VRV/VRFSystem: Supply, Installation, testing and commissioning of AIR COOLED & INVERTER BASED VARIABLE REFRIGERANT VOLUME / VARIABLE REFRIGERANT FLOW MODULAR TYPE AIR CONDITIONING SYSTEM with R410A suitable for 415 ± 10% , 50 Hz. The unit shall consist of indoor units and external condensing units and other accessaries as listed below complete in all respects as under

Outdoor Unit: SITC Modular type outdoor units equipped with highly efficient inverter type scroll compressor(s) with special precoated heat exchanger, low noise condenser fan housed in compact housing duly powder coated. Outdoor units shall have both cooling & heat pump mode, and environmet friendly refrigerant R-410A.The C.O.P shall be confirmed by vendor at full and part load at 41 deg C ambient temperature.Complete with M.S mounting stand of approved design for outdoor unit.Nitogen Flushing before gas charging.Pressure testing should be done after installation.Anti corrosive coating should be done at site.

(a) 20 HP (Actual) at 41 Deg C

Indoor Units: Supply,Installation, testing and commissioning of both interconnected with copper refrigerant & drain pipe of required length, insulation, full charge of refrigerant gas and oil, M.S. base frame duly primered & painted, supports etc. complete as per specifications and drawings.

Cassette Type: SITC of Imported Air Cooled VRV/VRF Cassette type Indoor units equipped with pre-filter, fan section with low noise fan, multispeed motor, coil section with DX coil, electronic expansion valve, outer cabinet, drain Pump and pan, insulation, pipe connections,control and power panel with corded remote control etc. etc. of various capacities as per specifications and drawings

HI-Wall Type: SITC of Imported Air Cooled VRV/VRF HI-Wall type Indoor units equipped with pre-filter, fan section with low noise fan, multispeed motor, coil section with DX coil, electronic expansion valve, outer cabinet, insulation, pipe connections,control and power panel with corded remote control etc. etc. of various capacities as per specifications and drawings

Installation &Allied Works: Y-joints & header etc above complete as per specification and drawings.

Supply,Installation, testing and commissioning of Centralised remote controllers for operation & status monitoring of VRV/VRF indoor units.

Refrigerant Piping: Supply,installation,testing and commissioning of Interconnecting non exposed refrigerant pipe work with (19mm/13 mm thick) , Class 'O', k value-0.035 w/mk minimum, Density not less than 55 Kg/cu.m closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with MS hanger & clamps.

(a) 41.3 mm O.D. (insulation : 19 mm)

(b) 34.9 mm O.D. (insulation : 19 mm)

(c) 28.6 mm O.D. (insulation : 19 mm)

(d) 22.2 mm O.D. (insulation : 13 mm)

(e) 19.1 mm O.D. (insulation : 13 mm)

(f) 15.9 mm O.D. (insulation : 13 mm)

(g)12.7 mm O.D. (insulation : 13 mm)

(h) 9.5 mm O.D. (insulation : 13 mm)

(i) 6.5 mm O.D. (insulation : 13 mm)

Supply,installation,testing and commissioning of Interconnecting exposed refrigerant pipe work with (19mm thick) , Class 'O', k value-0.035 w/mk minimum, Density not less than 55 Kg/cu.m closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with MS hanger & clamps Refrigerant piping will be coated with three layers of feviprotekt (only pidilite) weather coating.

28.6 mm O.D. (insulation : 19 mm)

15.9 mm O.D. (insulation : 13 mm)

Fresh air unit (for VRV): Supply, installation ,testing and commissioning of ventilation Ceiling Suspended Fan Sections of Single Skin Construction made of 18 G pre plasticized GI sheet, belt driven DIDW centrifugal forward curve fan with vibration isolators and canvas connection , squirrel cage induction motor with class-F insulation (IEE-3), mounted within the housing and all other details as in the drawings & specifications. Fan section supplied,filter sections with 50 mm thick washable synthetic type pre filter having efficiency 90% down to 10 micron,fine filters having efficiency 99% down to 3 micron with extruded aluminum frame as detailed in the drawings. The fan motor shall be suitable for operation on Single speed , the motor with Class-F insulation, 415 ± 15 Volts, 50Hz, Ac power.The fan static pressure shall be 80 mm WC static.Makes-(Zeco, System Air, Caryaire) (a) Fresh Air CFM=1200

Ventilation: Inline Fans : Supplying, Installing, Testing and Commissioning of Inline fans complete with motor, supporting frame, gravity louvres,etc. as per drawings and specifications. (a) 400 CFM ,. @ 15mm Static.

Drain Piping : Supply,installation,testing and commissioning of rigid PVC piping complete with fittings, supports as per specifications and duly insulated with 6 mm thick closed cell nitrile rubber class ‘O’. Providng and fixing pipes with all necessary fittings, supports and insulation.

Ducting: Supply, fabrication, installation, balancing and commissioning of factory fabricated GI sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings of following gauges as per SMACNA standard:- (a) Thickness 24 G sheet

Grilles/Diffusers: Supply,installation, testing and commissioning supply and return air grilles/ diffusers as per specifications and drawings including fixing frame of G.I./wooden in false ceiling/walls.

(a) Aluminium supply air grill with VCD

(b) Aluminium return/exhaust air Diffuser without VCD

Control & Transmission Wiring: Supply,installation,testing and commisioning of control cum transmission wiring of 2 core x 1.5 sqmm unarmoured copper in 25 MM heavy duty PVC conduits between indoor and out door unit & outdoor units to central remotes controllers.

A.C. Panel (For VRV/VRF): Supplying, assembling, erecting, connecting, testing and commissioning Outdoor type of dust, damp and vermin proof free floor standing factory built sheet steel enclosed non-drawout modular type Panel fabricated out of suitable sized angle iron and flats, base channel and covered with 2.0mm thick PCRC sheet, duly painted complete with earth bus, aluminium bus bar, numbering & sign writing, interconnection & including the cost of connection through bus bar / copper conductor flexible connection with all accessories, rotary handles,phase barriers etc. complete as shown in drawing & as per specifications and mounted with the followings etc. complete as required. (All the starters should have NO/ NC contacts for remote/ fire control facility etc. complete). 'Incomer: 1 No. 160 Amps MCCB TP+NL incoming. '1 No. 200. Amps aluminium conductor bus bar duly sleeved. 1 No. electronic energy meter with CTs. '1 No. Ammeter with ASS & CTs. 1 No. voltmeter with VSS. '3 Nos. phase indicating lamps '3 Nos. On,Off,Trip indicating lamps

Weather Proof isolators: Supply, installation, testing and commissioning of out door weather proof switch box of continuous welded construction, fabricated out of 2 mm thick G.I. sheet complete with water tight gasket with front openable and lockable door including earthing, painting, glands, danger boards etc. suitable for mounting on wall with M.S. angle iron frame of size 40x40x6 mm consisting of relevant I.S. specifications and drawings. Weather proof box with MCCBs of suitable ratings near the outdoor units for isolations for VRV Outdoor Units.(63 Amps)

Electrical cable: Supply of PVC insulated armoured Copper conductor cables of 1.1 Kv grade. (a) 4 core - 10 mm2

Termination: Supplying and making end termination with brass compression gland and Copper lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (a) 4 core - 10 mm2

SUB HEAD - XXI : EOT CRANE WORK:

EOT CRANE FOR PROCESS BUILDING , CURING BUILDING , MACHINING BUILDING:

Part-I: - Supply:

Design, manufacture and supply of Double Girder EOT Cranes with all speeds 'VVVF' Drive control and micro speed arrangement for Hoist, CT & LT as per the specifications given in Annexure-IV and conforming to IS 807/IS 3177 and other relevant IS standards of the latest revisions as shown below complete with all taxes, duties and other charges such as transportation to site, loading and unloading at stores/building, where to be installed etc.,movement of material to work spot including the cost of paint as required. The Crane shall be designed for earthquake and sesmic qualification. Span to be measured by the Bidder at Site and it shall be his sole responsibility to provide span suitable.

Supply of 15 Ton capacity Double Girder crab type EOT Crane with VVVF drive & Digital Display for Lift Weight complete with long travel and cross travel movements as per technical specifications and as per IS: 807 / IS: 3177 and other relevant IS standards of the latest revision. All drives should be provided with alternative parallel path with DOL starter for main speed only. Building :Process Building-1No, Curing Building – 1No & Machining Building – 1No Span:16 + 0.5 mts Lift: 6 mts. Bay length: 60 mts.

Supply of shrouded bus bar system with double shoe copper current collections system complete with support tracks, cable loops, junction boxes and cable from main supply point to crane festoons with all necessary fixtures.

Supply of material for Gantry Rails section 40 Square bar of prime material in length of 10 mts and above complete with mounting arrangement at the building over the crane girder including painting of rails with approximate colour code as approved by the dept.

Part-II: - Erection, testing and commissioning :

Erection, testing and commissioning of EOT crane and other allied items mentioned in item S.No.16.01 of Part-I as per the relevant IS standards and as mentioned in the technical specifications given in Annexure-III of this Tender Enquiry.

Erection, testing and commissioning of 15 Ton capacity crab type EOT crane mentioned in Item S. No.16.03 of Part-I as per the relevant IS standards inclusive of installation of complete Crane completion of all electrical and mechanical works including performance tests with No load, Full load and over load testing as per the approved QA Plan etc complete.

Erection testing and commissioning of shrouded type current collection system complete as per the item Sl No 16.04 of Part I over the crane bay including tapping of supply for electrical panel testing & handing over the crane as per the approved QA plan etc complete.

Erection, testing & commissioning of Gantry rail section 40 Square bar mentioned in item Sl No 16.05 of Part -I with mounting arrangement and fixing hardware etc., complete over the bay length to match the span of the crane within the permissible accuracy levels for span in height variation as per the QA Plan etc complete.

EOT CRANE FOR INTEGRATION BUILDING:

Part-I: - Supply:

Design, manufacture and supply of Double Girder EOT Cranes with all speeds 'VVVF' Drive control and micro speed arrangement for Hoist, CT & LT as per the specifications given in Annexure-IV and conforming to IS 807/IS 3177 and other relevant IS standards of the latest revisions as shown below complete with all taxes, duties and other charges such as transportation to site, loading and unloading at stores/building, where to be installed etc.,movement of material to work spot including the cost of paint as required. The Crane shall be designed for earthquake and sesmic qualification. Span to be measured by the Bidder at Site and it shall be his sole responsibility to provide span suitable.

Supply of 5 Ton capacity Double Girder crab type EOT Crane with VVVF drive & Digital Display for Lift Weight complete with long travel and cross travel movements as per technical specifications and as per IS: 807 / IS: 3177 and other relevant IS standards of the latest revision. All drives should be provided with alternative parallel path with DOL starter for main speed only. Building :Integration Building-1No Span:16 + 0.5 mts Lift: 6 mts. Bay length: 60 mts.

Supply of shrouded bus bar system with double shoe copper current collections system complete with support tracks, cable loops, junction boxes and cable from main supply point to crane festoons with all necessary fixtures.

Supply of material for Gantry Rails section 40 Square bar of prime material in length of 10 mts and above complete with mounting arrangement at the building over the crane girder including painting of rails with approximate colour code as approved by the dept.

Part-II: - Erection, testing and commissioning :

Erection, testing and commissioning of EOT crane and other allied items mentioned in item S.No.16.01 of Part-I as per the relevant IS standards and as mentioned in the technical specifications given in Annexure-III of this Tender Enquiry.

Erection, testing and commissioning of 15 Ton capacity crab type EOT crane mentioned in Item S. No.16.03 of Part-I as per the relevant IS standards inclusive of installation of complete Crane completion of all electrical and mechanical works including performance tests with No load, Full load and over load testing as per the approved QA Plan etc complete.

Erection testing and commissioning of shrouded type current collection system complete as per the item Sl No 16.04 of Part I over the crane bay including tapping of supply for electrical panel testing & handing over the crane as per the approved QA plan etc complete.

Erection, testing & commissioning of Gantry rail section 40 Square bar mentioned in item Sl No 16.05 of Part -I with mounting arrangement and fixing hardware etc., complete over the bay length to match the span of the crane within the permissible accuracy levels for span in height variation as per the QA Plan etc complete.

EOT CRANE FOR PRESSURE TEST FACILITY:

Part-I: - Supply:

Design, manufacture and supply of Double Girder EOT Cranes with all speeds 'VVVF' Drive control and micro speed arrangement for Hoist, CT & LT as per the specifications given in Annexure-IV and conforming to IS 807/IS 3177 and other relevant IS standards of the latest revisions as shown below complete with all taxes, duties and other charges such as transportation to site, loading and unloading at stores/building, where to be installed etc.,movement of material to work spot including the cost of paint as required. The Crane shall be designed for earthquake and sesmic qualification. Span to be measured by the Bidder at Site and it shall be his sole responsibility to provide span suitable.

Supply of 5 Ton capacity Double Girder crab type EOT Crane with VVVF drive & Digital Display for Lift Weight complete with long travel and cross travel movements as per technical specifications and as per IS: 807 / IS: 3177 and other relevant IS standards of the latest revision. All drives should be provided with alternative parallel path with DOL starter for main speed only. Building :Integration Building-1No Span:10 + 0.5 mts Lift: 5 mts. Bay length: 16 mts.

Supply of shrouded bus bar system with double shoe copper current collections system complete with support tracks, cable loops, junction boxes and cable from main supply point to crane festoons with all necessary fixtures.

Supply of material for Gantry Rails section 40 Square bar of prime material in length of 10 mts and above complete with mounting arrangement at the building over the crane girder including painting of rails with approximate colour code as approved by the dept.

Part-II: - Erection, testing and commissioning :

Erection, testing and commissioning of EOT crane and other allied items mentioned in item S.No.16.01 of Part-I as per the relevant IS standards and as mentioned in the technical specifications given in Annexure-III of this Tender Enquiry.

Erection, testing and commissioning of 15 Ton capacity crab type EOT crane mentioned in Item S. No.16.03 of Part-I as per the relevant IS standards inclusive of installation of complete Crane completion of all electrical and mechanical works including performance tests with No load, Full load and over load testing as per the approved QA Plan etc complete.

Erection testing and commissioning of shrouded type current collection system complete as per the item Sl No 16.04 of Part I over the crane bay including tapping of supply for electrical panel testing & handing over the crane as per the approved QA plan etc complete.

Erection, testing & commissioning of Gantry rail section 40 Square bar mentioned in item Sl No 16.05 of Part -I with mounting arrangement and fixing hardware etc., complete over the bay length to match the span of the crane within the permissible accuracy levels for span in height variation as per the QA Plan etc complete.

SUB HEAD - XXIV: EXTERNAL WATER SUPPLY SYSTEM.:

Providing and fixing G.I. pipes of following sizes complete with G.I. fittings including trenching and refilling etc.

a) 80 mm dia nominal bore

b) 65 mm dia nominal bore

c) 50 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :

a) 25 to 40 mm nominal bore.

b) 50 to 80 mm nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approvedvquality (screwed end) :

a) 80 mm nominal bore

b) 65 mm nominal bore

c) 50 mm nominal bore

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

a) With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

SUB HEAD - XXV : ROAD WORK:

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in-Charge: (a) All kinds of soil

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Supply and laying of moorum (of plasticity index <6) in road embankment to proper grade and level in layer of 150mm thickness and consolidating with road roller to achieve the modified proctor density of 97%, all complete as per drawing, specficiations and directions of Engineer-in-Charge.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all eads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. (a) With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30.

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing and applying tack coat using hot straight run bitumen of grade VG - 10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler,cleaning and preparing the existing road surface as per specifications : (a) On W.M.M. @ 0.75 Kg I sqm.

Providing and laying Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade,level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge. (a) 40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.

SUB HEAD - XXVI : SECURITY WALL:

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. (a) All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in Depth,consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

(a) 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : (a) Cement mortar 1:6 (1 cement : 6 coarse sand).

Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like. (a) Cement mortar 1:6 (1 cement : 6 coarse sand).

Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) : (a) Flush/ Ruled pointing

SUB HEAD -XXVII : ARBORICULTURE / LANDSCAPING:

Supply of grass and planting by dibbling the area including watering & Maintenance of Lawn for 30 days or more till grass forms a thick lawn cushion free from weeds. With Bermuda Grass (15 cm x 15 cm apart) Including One Year Maintenance after Completion of Work.

Trees:- Digging of pits of size 1x1x1m and refilling with good agriculture soil and well decomposed cattle manure in 4:1 ratio. Supply and planting of approved Tree species of healthy grownup saplings with good root system. Saplings should be of minimum 4 ft height from ground level after plantation. Maintenance includes, regular watering, de-weeding, loosening of soil fortnight, manuring with cattle manure and fertilizer, training, pruning, staking and spraying of insecticide and fungicide, Including One Year Maintenance after Completion of Work.

Shrubs: Digging of pits of size 0.60x0.60x0.60m and refilling with good agriculture soil and well decomposed cattle manure in 3:1 ratio. Supply and planting of approved Shurbs species of healthy grownup saplings with good root system. Saplings should be of minimum 2 ft height from ground level after plantation. Maintenance includes, regular watering, de-weeding, loosening of soil fortnight, manuring with cattle manure and fertilizer, training, pruning, staking and spraying of insecticide and fungicide, Including One Year Maintenance after Completion of Work.

Hedges: Digging of trenches of size 0.30 x 0.30m (width & depth) and refilling with good agriculture soil and cattle manure in 4:1 ratio. Maintenance includes, regular watering, de-weeding, loosening of soil fortnight, manuring with cattle manure and fertilizer, pruning, shaping and spraying of insecticide and fungicide, Including One Year Maintenance after Completion of Work.

Flower Beds: Digging upto 0.10m refilling with good soil and cattle manure in 3:1 ratio. Preparation of beds supply and planting of of healthy grown up plant material. Maintenance includes regular watering, de-weeding, manuring with manure and fertilizer.pruning, shaping and spraying of insecticide and fungicide, Including One Year Maintenance after Completion of Work.

Potted Plants: Supply and maintaining the Indoor and Outdoor potted plants in a good healthy and disease free condition of various varieties and in different type of pots.

Clearing jungle including uprooting of trees and saplings of girth 30 cm to 50 cm and replanting of uprooting trees as per direction of Engineer - in - charge.

SUB HEAD XXVIII : FURNITURE:

Supply of Sr. Executive Table of curve shape of size 3000 x 1050 x 750mm made out of 19mm thick commercial board with 4mm thick Teak veneer in Double (Decorative) pattern & top to have 30mm thick, front. having 4 Nos drawers (Right/Left) ride on Quadro Sliding channels, with locking arrangment with teak wood foot rest of size 100 x 30, all exposed edges to have teak wooden Beading and top to have finish with PU polish and inner sides with 0.8 lamination etc. all complete and Executive Side Unit of size 1350 x 525 x 750 mm and Executive back unit of 3000 x 450 x 750 mm. of Godrej or equivalent as per direction Engineer-in-Charge.

Supply and placement of Executive high back chair, The cushioned seat assembly shall consists of insert moulded polyurethane foam upholstered with foam laminated mesh fabric. the insert moulded foam is assembeled over a load bearing plastic seat cover. The back shallmade up of two piece injection moulded frame. The inner frame shall be upholstered with mesh fabric and mounted on the main assembly. Size of back shall be (W)-48.5cm, (H)-62.0cm & size of seat shall be (W)-52.5cm x (D)-51.0cm.armrest shall be injection moulded with height adjustable up to 4.5+/-0.5cm in 3 steps and width adjustable up to 20mm. The mechanism of chair shall have following features:360 degree revolving type, Front pivot Synchro mechanism, Tilt tension adjustment, 3 position tilt limiter with Anti-Shock feature. Spine bracket shall made of Aluminium diecast piece connecting back with mechanism. Neck rest assembly shall made up of polyurethane foam upholstered with foam laminated mesh fabric. The neck rest assembly is mounted on the top of back. it can be adjusted up to 4.5+/-0.5cm up-down and has regular adjustment of 30 degree +/-2 of Godrej or equivalent.

Supply and placement of Visitor / conference chair : The seat shall be made up of 1.2 +/- 0.1 cm thick hot pressed moulded reconstituted wood & upholstered with leather and moulded polyurethane foam. The back shall be designed with contoured lumber support for extra comfort. Size of back shall be (W)-45.0cm, (H)-49.0cm & size of seat shall be (W)-49.0cm x (D)-49.5cm. High Resilience (HR) foam should be used in making seat & back which shall be moulded with density 45 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression. The back rest should be connected to the mechanism with a drop-lift mechanism which can be adjusted in the range of 7.0+/-0.5cm for the comfortable back support to suitable individual need. Armrests should be pressure die casted in polished aluminium with PP arm tops of Godrej or equivalent

Supply of Officer`s table of size 2100 X 1050 X 750 mm made out of 19mm thick commercial block board including side unit fronts & sides, top to have 19mm thick commercial board with 4 mm thick one side teak wood ply, having 4 Nos drawer on Right / Left hand side (as required) with locking arrangement for one drawer & , including necessary hardware & fittings , all edges covered with teak wood beading & finish with melamine polish. etc all complete of Godrej or equivalent including side unit.

Supply and placement of high back chair, The seat is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18.The Back is made up of injectionmoulded glass filled nylon & upholstered using Net fabric with high tenacity BACK SIZE : 45.0 cm. x 65.3 cm. HIGH RESILIENCE POLYURETHANE FOAM: The HR polyurethane foam is moulded with density=55+/-2 kg/m³ and hardness 16 ± 2 kgf asper IS:7888 for 25% compression. The armrests have an Up-Down adjustment of 8.5 ± 0.5cm which is provided in armrest structure. Armrest Top has an integrated layer of Thermoplastic Elastomer(TPE). LUMBAR SUPPORT ASSEMBLY:The Lumbar support consists of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0 ± 0.5cm in height of Godrej marvel or equivalent

Supply of Executive Designer Five seater sofa (3+1+1) made out of 50 x 25mm second class hard wood frame having with teak wood in designer & decorative pattern and 100mm thick high density foam in seat & back with 50mm thick rubber foam quitting with 20mm thick u foam of high density including upholstry with fabric of approved shade & quality all exposed teak wood frame finish with melamine polish . Three Seater Size 1790 x 835 x 550 and single seater sofa Size 670 x 835 x 550mm). etc all complete of Godrej or equivalent.

Supply of Officer`s table of size 1800 X 1050 X 750 mm made out of 19mm thick commercial block board fronts & sides, top to have 19mm thick commercial board with 4 mm thick one side teak wood ply, having 4 Nos drawer on Right / Left hand side (as required) with locking arrangement for one drawer & , including necessary hardware & fittings , all edges covered with teak wood beading & finish with melamine polish. etc all complete of Godrej CIGNUS or equivalent.

Supply of Officer`s table of size 1600 X 900 X 750 mm made out of 19mm thick commercial block board fronts & sides, top to have 19mm thick commercial board with 4 mm thick one side teak wood ply, having 4 Nos drawer on Right / Left hand side (as required) with locking arrangement for one drawer & , including necessary hardware & fittings , all edges covered with teak wood beading & finish with melamine polish. etc all complete of Godrej or equivalent.

Supply and placement of Visitor / conference chair : Upholstered with fabric and moulded Polyurethane foam and back covers. The back foam shall be designed with contoured lumbar support for extra comfort. Dimensions of Back shall be: (W)46.0 cm x (H)50.5 Cm, and of Seat : (W)46.0cm x (D) 48.0 cm. The HR polyurethane foam shall be moulded with Density= 45 ±2 kg/m3 and back hardness load 12 ± 2 kgf and seat hardness load 16 ±2 as per IS:7888 for 25% compression. spine cap shall be made up of Polypropylene which covers the back frame and spine junction. The armrests shall have only Up-Down adjustment- 8.0±0.5cm (8 positions) which shall be provided in armrest structure. Armrest Top is made up of PU with metal insert fitted on the armrest structure of Godrej ACE or equivalent.

Supply and placement of high back chair, The seat is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18.The Back is made up of injectionmoulded glass filled nylon & upholstered using Net fabric with high tenacity BACK SIZE : 45.0 cm. x 65.3 cm. HIGH RESILIENCE POLYURETHANE FOAM: The HR polyurethane foam is moulded with density=55+/-2 kg/m³ and hardness 16 ± 2 kgf asper IS:7888 for 25% compression. The armrests have an Up-Down adjustment of 8.5 ± 0.5cm which is provided in armrest structure. Armrest Top has an integrated layer of Thermoplastic Elastomer(TPE). LUMBAR SUPPORT ASSEMBLY:The Lumbar support consists of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0 ± 0.5cm in height of Godrej or equivalent.

Supply of 600mm deep and 750 mm height Conference Table for 25 persons ( `U` Shaped) made out of 19 mm thick commercial board with 4 mm teak veneer & top to have 40mm thick with 4mm thick teak and italian veneer on top in designer pattern and 19 mm thick commercial board tapered foot rest, vertical member with 19mm thick commercial board. Back with 19mm thick commercial board including 4 mm thick teak veneer all exposed edges to have teak wood beading including PU polishing etc. all complete of Godrej or equivalent.

Supply and placement of Mid back conference chair. BACKREST : The back is made up of 12mm thick (7 layers) hot pressed plywood and moluded back foam upholstered with Leatherette. The back ply and foam is designed with contoured lumber support for achieving comfortable seating posture. Back rest available in two sizes - High Back (HB) 790mm (H) X 500mm (W), Medium Back (MB) 620mm (H) X 500mm (W). The backrest tested for 1,20,000 cycles to be completed with a load of 44.5Kg as per ANSI / BIFMA X5.1. SEAT : The seat is made up of 12mm thick (7 layers) hot pressed plywood and moluded seat foam upholstered with fabric / Leatherette. Seat Size 490mm (W) X 500mm (D). The seat tested for 1,00,000 cycles to be completed with a load of 57kg impact force on the seat as per ANSI / BIFMA X5.1. ARM REST : ADJUSTABLE ARM : The armrests made up of black integral skin polyurethane with 40-55 Shore Hardness and reinforced with 2mm thick M.S. insert. Arm pad size 258mm (L) x 112mm (W). The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 6mm thick. HR steel. Arm rest available in 1D arm.

Supply of Single seater sofa made out of teakwood framework 25 x 50mm for the seat and back flat plastic newar strips for seat and back cladded with 100m thick high density foam for seat and 75mm thick for back, 12mm thick poly foam contouring with cotton lining cloth, upholstered with fabric of approved shade, armrest of 95 x 22mm wide of TW section and polished with melamine polish etc complete of Godrej or equivalent.

Supply of 2 seater sofa in approved configuration of size 1350 x 750 x 700mm made out of teakwood frame work, seat and back with 2nd class hard wood , seat cushioned with 75mm thick high density foam and extra padding with 20mm thick foam for making shape on seat & back. Back with 50 mm thick high density foam duly upholstered with fabric of approved shade & quality all exposed wooden surface finished with Melamine polish etc. all complete of Godrej or equivalent.

Supply of 3 seater sofa in approved configuration of size 1850 x 750 x 700mm made out of teakwood frame work, seat and back with 2nd class hard wood , seat cushioned with 75mm thick high density foam and extra padding with 20mm thick foam for making shape on seat & back. Back with 50 mm thick high density foam duly upholstered with fabric of approved shade & quality all exposed wooden surface finished with Melamine polish etc. all complete of Godrej or equivalent.

Supply and placement of Almirah large of size 900mm(W)x507mm (D)x1950mm(H) (Height without leveler) Aesthetically appealing Slimline, completely knock down construction. Removable Skirting to cover integral legs. Legs fitted with screw type leveler, Made from combination of CRCA 0.8 mm & 0.6 mm Thickness. Steel Hinged Door Handle & Base Aesthetically appealing, Ergonomic, flush with door made from Zinc alloy. 3 way 90 Degree Removable key type Cam lock & locking mechanism Fixed Half locker on RH side. Hinged Door, 2 way Cam lock with Knob type handle Height wise Adjustable Shelf Mounting. 4 Nos. of Full Adj.Shelves, Epoxy Powder coated to the thickness of 50 microns (+-10). Make Godrej or equivalent.

Supply and placement of Almirah small of size 900mm(W)x507mm(D)x1372mm(H) (Height without leveler) Aesthetically appealing Slimline, completely knock down construction. Removable Skirting to cover integral legs. Legs fitted with screw type leveler Made from combination of CRCA 0.8 mm & 0.6 mm Thickness. Steel Hinged Door Handle & Base Aesthetically appealing, Ergonomic, flush with door made from Zinc alloy. 3 way 90 Degree Removable key type Cam lock & locking mechanism Fixed Half locker on RH side Hinged Door. 2 way Cam lock with Knob type handle Height wise Adjustable Shelf Mounting. 2 Nos. Of Full Adj.Shelves, Epoxy Powder coated to the thickness of 50 microns (+-10). Make of Godrej or equivalent.

Supply and placement of Staff chair, The seat and back shall be made up of 1.2 ±0.1cm. thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and shall be upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam shall be designed with contoured lumbar support for extra comfort. The dimensions of the back shall be 49.0 cm. (W) x 47.0 cm and of seat shall be 49.0 cm. (W) x 44.0 cm. (D). The HR Polyurethane foam shall be moulded with density= 45 ±2 kg/m3 and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The armrest tops shall be injection moulded from black Polypropylene. They shall be fitted to tubular armrest supports made of dia 2.54 ±0.03cm. x 0.16 ±0.0128cm.thk. M.S. E.R.W. tube and black powder coated ( DFT 40-60 microns ). The tubular armrest supports should hold together the seat and back. The tubular frame shall be cantilever type & made of 0 2.54±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated (DFT 40-60 microns). Overall Dimensions of Chair shall be Seat Height - 43.0cm, Height - 80.0cm, Width & Depth of Chair as measured from pedestal - Width-55.0 cm and Depth-61.0 cm. Make of Godrej STARR or equivalent.

Supply of Cafeteria Table of six e1800 x 900 x 750mm made out of teak wood frame 70 x 70 mm thick decorative teak wood legs and 95 x 25mm thick side rail `C` grove in designer pattern, top to have 12mm thick Glass with with teak wood frame egde polish and finished with melamine polish etc. all complete of Godrej or equivalent.

Supply of Cafeteria chair of size 450 x 450 x 950 mm made out of teak wood frame work without arm with 12 mm thick commercial ply with 50 mm thick rubber foam on seat duly upholstered seat with fabric, back to have decorative teak wood strips of approved shade and quality including melamine polish etc. all complete of Godrej or equivalent.

Supply of Conference Table for 6 Persons ('Oval' Shaped) of size 3600 x 1200 x 750mm made out of 19mm thick commercial board with 4mm teak veneer & top to have 40mm thick with 4mm thick teak and Italian veneer on top in designer pattern and 19mm thick commercial board tapered foot rest, vertical member with 19mm thick commercial board. Back with 19mm thick commercial board including 4mm thick teak veneer all exposed edges to have teak wood beading including PU polishing etc. all complete of Godrej or equivalent.

Computer Table, Make: Godrej, Model: Enterprise w/o CPU Hangar of Godrej or equivalent.

Supply and placement of Computer mid back Chair, the seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia 2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 64.5 cm (H). The HR polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The powder coated (DFT 40-60 microns) tubular frame shall be cantilever type & made of dia 2.54±0.03cm x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall Dimensions of Chair shall be Seat Height - 46.5cm, Height - 97.5cm, Width & Depth of Chair as measured from pedestal -Width-61.0 cm and Depth-64.5 cm. of of Godrej BRAVO or equivalent.

Supply and placement of Vertical sliding door unit of VSDU - 2 of size 900mm(W)x450mm(D)x711mm(H). The top shall be Metal top (1 mm add in unit height ) .The Rigid Knock Down Construction , Back , Sides and Door shall be made from 0.7 mm high yield strength CRCA ,rest in 0.8 mm CRCA . CRCA - 'D' Grade as per IS-513 . Sliding door arrangement shall have sliding door wth top hanging arrangement to prevent derailment . Each door shall be provided with 2 plastic roller having steel ball bearing for smooth movement of door & less noise . Locking shall be 5 lever cam lock for safe locking . Handle shall be plastic flush & recessed handle . Shelving shall have Height wise adjustable shelf mounting . Uniformly Distributed Load Capacity of the shelf is 40 Kg maximum . VSDU - 2 shall have 1 no. of adjustable full shelf . Accessories optional shall be cradle with pipes for hanging godrej instadex files . Leveler shall be screw type leveler with hex plastic base and overall finish shall be epoxy polyester coated to the thickness of 50 microns . For VSDU 2 - A4 size box file can be stored vertically on one shelf and clear space above second shelf is 220 mm . Model of Godrej or equivalent.

Supply of Corner Table of height 450 mm with 12 mm thick glass of size 525 x 525 mm fixed with SS studs, supported on 50 x 25 mm teak wood frame and 45 x 45 mm teak wood legs, braced with teak wood frame of size 25 x 50 mm at lower level and upper level 45 X 45 mm teak wood, etched glass of 6mm thickness at lower level, finished with melamine polish etc. all complete of Godrej or equivalent.

Supply of Center Table of height 450 mm with 12 mm thick glass of size 1050 x 525 mm fixed with SS studs, supported on 50 x 25 mm teak wood frame and 45 x 45 mm teak wood legs, braced with teak wood frame of size 25 x 50 mm at lower level and upper level 45 X 45 mm teak wood, etched glass of 6mm thickness at lower level, finished with melamine polish etc. all complete of Godrej or equivalent.

Supply of notice board of size 1800mm x 1200mm make of Godrej or equivalent.

Supply and placement of tool cabinet with retractable shelves FDF 0570 00 04 Requirement Fami make heavy duty MOBILE CABINET with overall dimensions of 792x600x860 h COLOUR- RAL 5012 Overall dimensional tolerance should be 0.01mm. Each unit should be made up of the following components 1. Empty cabinet 2. Retractable shelves- 3nos. 3. Anti tilt mechanism 4. Secure central locking mechanism. 5. Wheels 6. Rubber cover top with handle Specifications of components :

1. Empty cabinet Empty cabinet should be of overall dimensions 717mm L x 600mm D x 967mm H with a usable height of 700mm. Cabinet body should be made from virgin cold rolled steel of thickness 0.8mm. Cabinet should be of welded construction with slotted uprights of 1.25mm thick welded on the body. Material used for constructing the cabinet is first quality steel of grade’s EN10130 & EN10111. Cabinet is designed in such a way that the drawers can be placed with a pitch of 25 mm of vertically. Load bearing capacity of cabinet = UDL 225 Kg.

2. Retractable shelves- 3nos : The cabinet should house 3 numbers of height adjustable retractable shelves of usable dim mm: 587x475d Each retractable shelf should be of 100% extension. Each drawer should be capable of carrying a UDL of 70 Kg subject to the overall cabinet load of 225kg. The shelf should be made of CR steel of thickness of 1 mm. 3. Anti tilt mechanism : The unit should be fitted with anti – tilt mechanism in order to prevent accidental toppling by ensuring only one drawer can be opened at any time. the anti tilt rod should be fixed to the cabinet using heavy duty high density poly propylene bearings to ensure a life of 15 years under repeated stress and dynamic loads.

4. Secure central locking : The unit should be provided with a secure tamper proof central locking mechanism located at the centre of top panel of the cabinet. Keys should be provided in duplicate. 5. Rubber cover top with handles : 4 edged top with oil-resistant rubber, the handles can be fitted towards the bottom thereby reducing the height by 22 mm. Pre treatment and surface finish, the raw material used in production of the unit provided should be virgin steel. Make Godrej FDF 0570 00 04 or equivalent specification of Wipro/Featherlite/Durian/Ergo/Ikea.

Supply and placement of Wooden work bench with overall dimensions of 2000mm L x 750mm D x 840mm HColour RAL 5012 BLUE. Each unit should be made up of the following components1. Multiplex Worktop2. A pair of LegsSpecifications of omponents1. Multiplex Work top The worktop should be made of various layers of beech wood which are planed, glued and pressed together. This should make the work top non-deformable, and load and wear resistant.The worktop comes with 3mm thick black color oil proof rubber coated.Overall dimensions of worktop

should be 2000mm L x 750mm D x 40mm H.Load bearing capacity of Workbench = UDL 500 Kg. 2. A pair of bench legs Work bench has 2sets of bench legs of 80x40 C-channel of 1.2mm thick. The bench legs should be powder coated to the specifications mentioned belowPre treatment and surface finish The raw material used in production of the unit provided should be virgin steel. The same should undergo 7 steps anti rust and anti corrosion treatment with special hot oil treatment to safeguard against saline and humid conditions. The final product should be powder coated to 80 micron thickness with Epoxy Polyester blend and should meet the following criteria. Working table 2mtrs. Make of Godrej or equivalent.

Supply and placement of Boltless shelves storage rack of size R1300W x 450D x 2111Hmm 5 load leve, 100 kg per shelf, closed type. Make of Godrej or equivalent.

SUB HEAD - XXIX : EXTERNAL SEWERAGE SYSTEM:

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete:

(a)100 mm diameter.

(b)150 mm diameter.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all around S.W pipe including bed concrete as per standerd design:

(a)100 mm diameter.

(b)150 mm diameter.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: (a)150 x 100 mm size P type. (i)With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : (a) 200 mm dia RCC pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of RCC pipes including bed concrete as per standard design : (a) 200 mm Dia.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions,total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : (a) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Extra for depth for manholes : (a) Size 90x80 cm. (i) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

SUB HEAD - XXX : EXTERNAL DRAINAGE WORK:

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. (a) All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: (a) Cement mortar 1:6 (1 cement : 6 coarse sand).

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. (a) 20 mm cement plaster.

SUB HEAD - XXXI : WATER COOLER :

Supply , installation testing and commissioning of storage water cooler with storage capacity of 80 liters and cooling capacity of 40 liters suitable for operation on 230V +10% , 50 HZ, full stainless steel body including multistorage RO Purification system , 2 KVA voltage stabilizer etc complete Make Wate Cooler : Voltas / Blue Star / Usha. Water Purifier : Eureka Forbes / Kent / ION Exchange. Stabilizer : Keeline / V- Guard

SUB HEAD - XXXII : FIRE FIGHTING SYSTEM :

Providing, laying, testing and commissioning of Class "C" heavy duty MS pipe conforming to IS:1239 including heavy duty fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc., fixing the pipe on pipe on the wall / ceiling with suitable clamps and painting with two or more coats of synthetic signal red paint of required shade complete as required. Pipes from 25 to 50 mm shall have threaded fittings of malleable GI fittings. All supports are to be included.

(a) 150 mm dia.

(b) 80 mm dia.

Supplying and fixing stainless steel single headed internal and external hydrant valve with instantaneous stainless steel couplings of 63 mm dia with cast iron wheel, ISI marked conforming to IS:5290 ( Type A ) with blank plastic cap and chain as required.

Supplying and fixing synthetic 63 mm dia, 15 M long synthetic hose pipe with 63 mm dia male and female stainless steel couplings duly binded with GI wire, rivets etc conforming to IS:636 as required.

Supplying and fixing 63 mm dia stainless steel branch pipe with 20 mm ( nominal internal diameter ) size stainless steel nozzle conforming to IS:903, suitable for instantaneous connection to interconnect hose pipe coupling as required.

Supplying and fixing First Aid Hose Reel with MS construction spray painted in Post Office Red, conforming to IS:884 with upto date amendments, complete with the following as required : 36 m long 25 mm ( nominal internal ) dia water hose thermo plastic pipe. 25 mm ( nominal internal ) dia ball valve and nozzle. Drum and brackets for fixing the equipments on wall. Bracket shall be of aluminium alloy. Connections from Riser with 25 mm dia stop valve & MS pipe.

Supplying and fixing of hose cabinet of size 900 mm x 600 mm x 450 mm made of 3 mm thick powder coated aluminium sheet with 6 mm thick glazed glass doors including necessary locking arrangement suitable to accommodate external hydrants, 2 nos 15 m long hose pipe, 1 no branch pipe with 4 nos MS angle ( 40 x 40 x 8 ) supports grouted in floor and duly powder coated with post office red external and white internal paint complete in all respects, for external hydrant, as required.

Supplying and fixing of hose cabinet of size 900 mm x 600 mm x 2100 mm made of 3 mm thick powder coated aluminium sheet with 6 mm thick glazed glass doors including necessary locking arrangement suitable to accommodate external hydrants, 2 nos 15 m long hose pipe, 1 no branch pipe with 4 nos MS angle ( 40 x 40 x 8 ) supports grouted in floor and duly powder coated with post office red externa and white internal paint complete in all respects, for INTERNAL hydrant, as required.

9 litres water type fire extinguisher IS 15683 marked deep drawn cylinder with internal plastic lining and 60 gms CO2 cartridge, siphon tube, plunger ( spring operated ) and discharge tube.

4.5 kg Carbon Dioxide Extinguisher with squeeze grip IS 15683 marked.

Providing & fixing, testing and commissioning of Ductile Iron double flanged FM approved sluice valve of rating PN 1.6 with rising spindle, bronze / gun metal seat complete with nuts, bolts, washers, gaskets, of following sizes as required : (a) 150 mm dia.

SSC PROJECTS PRIVATE LIMITED

P L Raju Constructions Ltd

RIC Projects Pvt. Ltd.