Loading
Loading…
Loading…
Tender Value
₹8.5 Cr
EMD Value
₹17.1 L
Closing Date
10 Apr 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
GENERAL
19 conditions · 2 needing a document upload
Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees, N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. SPECIAL NOTE:- The balance sheet and all other financial documents attested/certified by CAs to substantiate fulfilment of Financial Eligibility Criteria should be with UDIN, failing which the offer is likely to be rejected without any further reference. (Authority: CE's letter No.- CE/G/Arb& Cont. Mgt./Tender Circular/Pt.1/317, Dated: 11:03.2025)
Technical Eligibility Criteria: (a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender. (b) (1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2)In such cases, what constitutes a component in a composite work shall be clearly pre- defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing.
However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by the Railway. In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract, with prior approval of Chief Engineer in writing. Note for Technical Eligibility Criteria: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Credentials if submitted in foreign currency shall be converted into Indian currency i.e., Indian Rupee as under: The conversion rate of US Dollars into Rupees shall be the daily representative exchange rates published by the Reserve Bank of India or entity authorized by RBI to do so for the relevant date or immediately previous date for which rates have been published. Where, relevant date shall be as on the last day of month previous to the one in which tender is invited. In case of any other currency, the same shall first be converted to US Dollars as on the last day of month previous to the one in which tender is invited, and the amount so derived in US Dollars shall be converted into Rupees at the aforesaid rate. The conversion rate of such currencies shall be the daily representative exchange rates published by the International Monetary Fund for the relevant date or immediately previous date for which rates have been published.
[Explanation for Eligibility Criteria: 1. Substantially Completed Work means an ongoing work in which payment equal to or more than 90% of the present contract value (excluding the payment made for adjustment of Price variation (PVC), if any) has been made to the contractor in that ongoing contract and no proceedings of termination of contract on Contractor's default has been initiated. The credential certificate in this regard should have been issued not prior to 60 days of date of invitation of present tender. 2. In case a work is started prior to 07 (seven) years, ending last day of month previous to the one in which tender is invited, but completed in last 07 (seven) years, ending last day of month previous to the one in which tender is invited, the completed work shall be considered for fulfillment of credentials. 3. If a work is physically completed and completion certificate to this extent is issued by the concerned organization but final bill is pending, such work shall be considered for fulfillment of credentials. 4. In case of completed work, the value of final bill (gross amount) including the PVC amount (if paid) shall be considered as the completion cost of work. In case final bill is pending, only the total gross amount already paid including the PVC amount (if paid) shall be considered as the completion cost of work. In case of substantially completed work, the total gross amount already paid including the PVC amount (if paid), as mentioned in the certificate, shall be considered as the cost of substantially completed work. 5. If a bidder has successfully completed a work as subcontractor and the work experience certificate has been issued for such work to the subcontractor by a Govt. Organization or public listed company as defined in Note for Item 10.1 Para 10 of the Tender Form (Second Sheet) of GCC April - 2022, the same shall be considered for the purpose of fulfillment of credentials.
6. In case a work is considered similar in nature for fulfillment of technical credentials, the overall cost including the PVC amount (if paid) of that completed work or substantially completed work, shall be considered and no separate evaluation for each component of that work shall be made to decide eligibility. 7. In case of newly formed partnership firm, the credentials of individual partners from previous propriety firm(s) or dissolved previous partnership firm(s) or split previous partnership firm(s), shall be considered only to the extent of their share in previous entity on the date of dissolution /split and their share in newly formed partnership firm. For example, a partner A had 30% share in previous entity and his share in present partnership firm is 20%. In the present tender under consideration, the credentials of partner A will be considered to the extent of 0.3*0.2*value of the work done in the previous entity. For this purpose, the tenderer shall submit along with his bid all the relevant documents which include copy of previous partnership deed(s), dissolution deed(s) and proof of surrender of PAN No.(s) in case of dissolution of partnership firm(s) etc. 8. In case of existing partnership firm, if any one or more partners quit the partnership firm, the credentials of remaining partnership firm shall be re-worked out i.e., the quitting partner(s) shall take away his credentials to the extent of his share on the date of quitting the partnership firm(e.g. in a partnership firm of partners A, B & C having share 30%, 30% & 40% respectively and credentials of Rs 10 crore; in case partner C quits the firm, the credentials of this partnership firm shall remain as Rs 6 crore). For this purpose, the tenderer shall submit along with his bid all the relevant documents which include copy of previous partnership deed(s), dissolution deed(s) and proof of surrender of PAN No.(s) in case of dissolution of partnership firm(s) etc.
9. In case of existing partnership firm if any new partner(s) joins the firm without any modification in the name and PAN/TAN no. of the firm, the credentials of partnership firm shall get enhanced to the extent of credentials of newly added partner(s) on the same principles as mentioned in item 6 above. For this purpose, the tenderer shall submit along with his bid all the relevant documents which include copy of previous partnership deeds, dissolution/splitting deeds and proof of surrender of PAN No.(s) in case of dissolution of partnership firm etc. 10. Any partner in a partnership firm cannot use or claim his credentials in any other firm without leaving the partnership firm i.e., In a partnership firm of A&B partners, A or B partner cannot use credentials of partnership firm of A&B partners in any other partnership firm or propriety firm without leaving partnership firm of A&B partners. 11. In case a partner in a partnership firm is replaced due to succession as per succession law, the proportion of credentials of the previous partner will 1.4.1 be passed on to the successor. 12. If the percentage share among partners of a partnership firm is changed, but the partners remain the same, the credentials of the firm before such modification in the share will continue to be considered for the firm as it is without any change in their value. Further, in case a partner of partnership firm retires without taking away any credentials from the firm, the credentials of partnership firm shall remain the same as it is without any change in their value. 13. In a partnership firm "AB" of A&B partners, in case A also works as propriety firm "P" or partner in some other partnership firm "AX", credentials of A in propriety firm "P" or in other partnership firm "AX" earned after the date of becoming a partner of the firm AB shall not beadded in partnership firm AB. 14. In case a tenderer is LLP, the credentials of tenderer shall be worked out on above lines similar to a partnership firm. 15. In case company A is merged with company B, then company B would get the credentials of company A also.]
Defination of Similar Work :- Any civil engineering works.
133 conditions · 7 needing a document upload
Checklists for submission of documents while submitting the tender. : It shall be mandatory to submit the following documents (relevant to the nature of the firm) along with offer.
If the accepted tender value is more than 5% below the advertised tender value, the contractor shall submit an additional Performance Guarantee at the rate of 5% of the contract value. (Authirity : Advance Correction Slip No. 11 to IRS GCC April-2022)
For Partnership firm/Joint Venture (JV) / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc.: - Please submit a Self-certificate by attorney/authorized signatory/each member of Partnership firm/Joint Venture (JV) / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. in the prescribed format as Annexure-V(A). Non submission of the certificate, or submission of certificate either not properly filled in, or in a format other than the prescribed format shall lead to summary rejection of your offer.
Fulfillment of Standard Technical and Financial Criteria as per tender documents.
(a) Sole Proprietorship Firm: (i) All documents in terms of Para 10 of the Tender Form (Second Sheet) IRSGCC April-2022.
(b) HUF: (i) A copy of notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF. (ii) All other documents in terms of Para 10 of the Tender Form (Second Sheet) IRSGCC April-2022.
(c) Partnership Firm: The following documents shall be submitted by the partnership firm, with the tender: (i) A notarized copy of the Partnership Deed or a copy of the Partnership deed registered with the Registrar. (ii) A notarized or registered copy of Power of Attorney in favour of the individual to tender for the work, sign the agreement etc. and create liability against the firm. (iii) An undertaking by all partners of the partnership firm that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP in which they were / are partners/members. Any Concealment / wrong information in regard to above shall make the bid ineligible or the contract shall be determined under Clause 62 of the Standard General Conditions of Contract. (iv) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of IRSGCC April-2022.
(d) Joint Venture (JV) (If applicable): The tenderer shall submit all documents as mentioned in para 17 of the Tender Form (Second Sheet) of IRSGCC April-2022.
(e) Company registered under Companies Act 2013: (i) The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company (ii) A copy of Certificate of Incorporation (iii) A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company. (iv) All other documents in terms Para 10 of the Tender Form (Second Sheet) of IRSGCC April-2022.
(f) LLP (Limited Liability Partnership): (i)A copy of LLP Agreement (ii)A copy of Certificate of Incorporation (iii) A copy of Power of Attorney/Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP. (iv) An undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP or JV in which they were / are partners/members. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract. (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of IRSGCC April- 2022.
(g) Registered Society & Registered Trust: (i)A copy of Certificate of Registration (ii)A copy of Memorandum of Association of Society/Trust Deed (iii) A copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust. (iv) A copy of Rules & Regulations of the Society (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of IRSGCC April-2022.
Declaration regarding Retd Railway Employee.
PAN
GST REGISTRATION
EPF REGISTRATION (IF APPLICABLE)
Bid Security as Bank Guarantee Bond from a scheduled commercial bank of India . The Bank Guarantee Bond shall be as per Annexure VIA (AVAILABLE IN GCC APRIL 2022 WHICH IS UPLOADED IN DOCUMENT TAB) and shall be valid for a period of 90 days beyond the bid validity period. The original Bank Guarantee should be delivered to officials of Engineering Tender cell/ RNC, before closing date for submission of bids (i.e. excluding the last date of submission of bids). Non submission of scanned copy of Bank Guarantee with the bid on e-tendering portal (IREPS) and/or non submission of original Bank Guarantee within the specified period shall lead to summary rejection of bid. Bank Guarantee Bond should be with following details:-
1.15.1 Acting through - DRM(Engg.), South Eastern Railway, Ranchi.
Beneficiary: FA & CAO, South Eastern Railway, Garden Reach, 1.15.2 Kolkata.
Duly filled and signed Annexure VIB (AVAILABLE IN GCC APRIL 2022 WHICH IS UPLOADED IN DOCUMENT TAB) ) duly supported by Audited Balance Sheet duly certified by the Chartered Accountant. (for work costing more than 50 lakhs )
Technical Eligibility Criteria (for work costing more than 50 lakhs).
BID CAPACITY:- For tenders having advertised value more than Rs 10 crore.
Joint Venture (JV):- For tenders having advertised value more than Rs 10 crore.
Commercial-Compliance:-
Tenderer must have valid PF code number. Tenderer should upload document with respect to valid PF code number . Bill will be cleared only after verification of PF challan paid for previous month among all other statutory dues by the contractor/establishment.
Tenderers are required to upload copy of Permanent Account Number & GST.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Hatia: Improvement and upgradation of 395 unit Type-II and 03 unit Type-IV quarters at Hatia Railway Settlement under the jurisdiction of ADEN/Settlement/Hatia.
DRMENGGRNC-11-2026
DRMENGGRNC-11-2026
Open
Works - General
12 Months
Ranchi, Jharkhand
₹0
₹17.1 L
10 Apr 2026
16 Mar 2026
27 Mar 2026
127 items across 2 schedules · ₹7,70,44,683.8 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | All kinds of soil | cum | 269 | 177.5 | 47,747.5 |
| 2 | All kinds of soil. | cum | 2100 | 260.3 | 5,46,630 |
| 3 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. | cum | 144 | 2,123.75 | 3,05,820 |
| 4 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 160 | 7,878.5 | 12,60,560 |
| 5 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 39 | 7,294.7 | 2,84,493.3 |
| 6 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. | Sqm | 174 | 749.3 | 1,30,378.2 |
| 7 | Foundations, footings, bases of columns, etc. for mass concrete | Sqm | 180 | 392.15 | 70,587 |
| 8 | Suspended floors, roofs, landings, balconies and access platform | Sqm | 620 | 927.25 | 5,74,895 |
| 9 | Lintels, beams, plinth beams, girders, bressummers and cantilevers | Sqm | 1560 | 736.4 | 11,48,784 |
| 10 | Columns, Pillars, Piers, Abutments, Posts and Struts | Sqm | 420 | 961.3 | 4,03,746 |
| 11 | Stairs, (excluding landings) except spiral- staircases | Sqm | 56 | 764.95 | 42,837.2 |
| 12 | Providing, transporting, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in vertical & horizontal fins, individually or forming box louvers, setting in cement mortar 1:2 (1 cement : 2 coarse sand), including the cost of required centering, shuttering but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). | cum | 45 | 12,043.35 | 5,41,950.75 |
| 13 | Thermo-Mechanically Treated bars of grade Fe-500D or more. | Kg | 26140 | 107.85 | 28,19,199 |
| 14 | Thermo-Mechanically Treated bars of grade Fe-500D or more. | Kg | 35100 | 107.85 | 37,85,535 |
| 15 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 161 | 9,504.75 | 15,30,264.75 |
| 16 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 270 | 9,860.4 | 26,62,308 |
| 17 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 500 | 7,132.25 | 35,66,125 |
| 18 | With F.P.S.(non modular) bricks | cum | 369 | 9,299.9 | 34,31,663.1 |
| 19 | Cement mortar 1:4 (1 cement :4 coarse sand) | Sqm | 190 | 1,123.8 | 2,13,522 |
| 20 | Area of slab over 0.50 sqm | Sqm | 12 | 5,136.3 | 61,635.6 |
| 21 | Granite work | Metre | 38 | 510.95 | 19,416.1 |
| 22 | Granite Stone of approved shade | Sqm | 5 | 4,051.85 | 20,259.25 |
| 23 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. | Sqm | 370 | 1,267.95 | 4,69,141.5 |
| 24 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Sqm | 79 | 2,172.1 | 1,71,595.9 |
| 25 | Fixed to steel windows by welding | Kg | 7500 | 219.1 | 16,43,250 |
| 26 | With 12 mm mild steel U beading | Sqm | 98 | 939.2 | 92,041.6 |
| 27 | 100 mm | Each | 84 | 206.25 | 17,325 |
| 28 | 125x63x4 mm | Each | 126 | 126.65 | 15,957.9 |
| 29 | 250x16 mm | Each | 42 | 260.6 | 10,945.2 |
| 30 | 250x10 mm | Each | 84 | 115.15 | 9,672.6 |
| 31 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineer- in-Charge. | Metre | 494 | 492.7 | 2,43,393.8 |
| 32 | 30 mm thick plain PVC door shutters | Sqm | 137 | 3,182.95 | 4,36,064.15 |
| 33 | Using R3 series with frame (98 mm & above) x (40 mm & above) & both glazed and fly screen sash (30 mm & above) x (55 mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. (Height upto 1.8m) | Sqm | 64 | 10,874.2 | 6,95,948.8 |
| 34 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Kg | 550 | 117.35 | 64,542.5 |
| 35 | Hot finished welded type tubes | Kg | 41000 | 194.4 | 79,70,400 |
| 36 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works | Kg | 35721 | 172.6 | 61,65,444.6 |
| 37 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). | Kg | 300 | 772.4 | 2,31,720 |
| 38 | Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete. | cum | 140 | 8,595.15 | 12,03,321 |
| 39 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. | Sqm | 750 | 1,096.55 | 8,22,412.5 |
| 40 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete. | Sqm | 420 | 1,315.3 | 5,52,426 |
| 41 | Size of Tile 600 x 600 mm | Sqm | 80 | 1,453.65 | 1,16,292 |
| 42 | Size of Tile 600 x 600 mm | Sqm | 110 | 1,464.85 | 1,61,133.5 |
| 43 | Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. | Sqm | 950 | 3,186.7 | 30,27,365 |
| 44 | Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent | Sqm | 130 | 4,481.3 | 5,82,569 |
| 45 | 110 mm diameter | Metre | 32 | 377.4 | 12,076.8 |
| 46 | 110 mm bend | Each | 16 | 150.35 | 2,405.6 |
| 47 | 110 mm Shoe | Each | 16 | 131.85 | 2,109.6 |
| 48 | 110 mm | Each | 36 | 371.3 | 13,366.8 |
| 49 | 12.5 mm thick tapered edge gypsum moisture resistant board | Sqm | 850 | 1,529.1 | 12,99,735 |
| 50 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in- charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | Sqm | 3800 | 738.65 | 28,06,870 |
| 51 | 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. | Sqm | 134 | 2,215.15 | 2,96,830.1 |
| 52 | Precoated/mill finish aluminium Gutter (600 mm over all girth) | Metre | 420 | 1,808.65 | 7,59,633 |
| 53 | 1:6 (1 cement: 6 fine sand) | Sqm | 9750 | 333.35 | 32,50,162.5 |
| 54 | 1:6 (1 cement: 6 fine sand) | Sqm | 7000 | 383 | 26,81,000 |
| 55 | 1:3 (1 cement : 3 fine sand) | Sqm | 1000 | 300.45 | 3,00,450 |
| 56 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. | Sqm | 6500 | 262.7 | 17,07,550 |
| 57 | New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre | Sqm | 16750 | 185.65 | 31,09,637.5 |
| 58 | New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) | Sqm | 111 | 171.1 | 18,992.1 |
| 59 | Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture | Sqm | 4200 | 226.25 | 9,50,250 |
| 60 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. | Sqm | 2068 | 156.05 | 3,22,711.4 |
| 61 | Old work (one or more coats) | Sqm | 11200 | 62.7 | 7,02,240 |
| 62 | Two coats | Sqm | 2000 | 142.8 | 2,85,600 |
| 63 | One or more coats on old work | Sqm | 850 | 102.8 | 87,380 |
| 64 | Old work (one or more coats @ 2.20 kg/10 sqm) complete. | Sqm | 5600 | 75.8 | 4,24,480 |
| 65 | Old work (one or more coats applied @ 0.83 ltr/10 sqm). | Sqm | 7500 | 88.55 | 6,64,125 |
| 66 | 3 mm thick | Sqm | 1000 | 537.45 | 5,37,450 |
| 67 | Nominal concrete 1:3:6 or richer mix (including equivalent design mix) | cum | 21 | 2,434.25 | 51,119.25 |
| 68 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. | cum | 18 | 3,551.25 | 63,922.5 |
| 69 | In cement mortar | cum | 259 | 2,060.2 | 5,33,591.8 |
| 70 | Of area 3 sq. metres and below | Each | 2076 | 367.2 | 7,62,307.2 |
| 71 | For thickness of tiles 10 mm to 25 mm | Sqm | 245 | 73.4 | 17,983 |
| 72 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. | Sqm | 12500 | 54.65 | 6,83,125 |
| 73 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests | Each | 10 | 6,767.4 | 67,674 |
| 74 | White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap | Each | 300 | 2,226.35 | 6,67,905 |
| 75 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer | Each | 20 | 3,960.55 | 79,211 |
| 76 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. | Each | 8 | 1,683.35 | 13,466.8 |
| 77 | 610x510 mm bowl depth 200 mm | Each | 67 | 4,940.8 | 3,31,033.6 |
| 78 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge. | Each | 10 | 349.15 | 3,491.5 |
| 79 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. | Each | 20 | 1,607.95 | 32,159 |
| 80 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. | Each | 4 | 1,083.5 | 4,334 |
| 81 | C.P. brass | Each | 10 | 803.7 | 8,037 |
| 82 | Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms | Each | 20 | 115.3 | 2,306 |
| 83 | Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms | Each | 39 | 367.1 | 14,316.9 |
| 84 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. | Each | 10 | 168.35 | 1,683.5 |
| 85 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. | Each | 10 | 231.95 | 2,319.5 |
| 86 | 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms | Each | 4 | 673.4 | 2,693.6 |
| 87 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. | Each | 10 | 14,999.15 | 1,49,991.5 |
| 88 | 20 mm nominal dia Pipes | Metre | 600 | 335 | 2,01,000 |
| 89 | 25 mm nominal dia Pipes | Metre | 650 | 401.55 | 2,61,007.5 |
| 90 | 20 mm nominal dia Pipes | Metre | 750 | 537.6 | 4,03,200 |
| 91 | 25 mm nominal dia Pipes | Metre | 130 | 627.25 | 81,542.5 |
| 92 | 32 mm nominal dia Pipes | Metre | 65 | 739.3 | 48,054.5 |
| 93 | 25 mm nominal dia Pipes | Metre | 87 | 355.4 | 30,919.8 |
| 94 | 32 mm nominal dia Pipes | Metre | 126 | 438.6 | 55,263.6 |
| 95 | 40 mm nominal dia Pipes | Metre | 62 | 563.05 | 34,909.1 |
| 96 | Horizontal | Each | 4 | 952.6 | 3,810.4 |
| 97 | 20 mm nominal bore | Each | 10 | 119.05 | 1,190.5 |
| 98 | 150 mm diameter | Each | 2 | 222.35 | 444.7 |
| 99 | With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 | Each | 6 | 10,862.4 | 65,174.4 |
| 100 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. | Per Litre | 6000 | 11 | 66,000 |
| 101 | 15 mm nominal bore | Each | 22 | 506.8 | 11,149.6 |
| 102 | 15 mm nominal bore | Each | 20 | 820.7 | 16,414 |
| 103 | 15 mm nominal bore | Each | 20 | 798.95 | 15,979 |
| 104 | 15 mm nominal bore | Each | 20 | 670.45 | 13,409 |
| 105 | 15mm nominal bore | Each | 20 | 574.3 | 11,486 |
| 106 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in- charge. | Each | 20 | 74.8 | 1,496 |
| 107 | 100 mm nominal dia | Each | 7 | 37.6 | 263.2 |
| 108 | 125 mm nominal dia with 25 mm waste hole | Each | 15 | 51.85 | 777.75 |
| 109 | Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. | Each | 10 | 452 | 4,520 |
| 110 | 15 mm nominal bore | Each | 20 | 8,803.7 | 1,76,074 |
| 111 | 150 mm dia. R.C.C. pipe | Metre | 90 | 556.45 | 50,080.5 |
| 112 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 | Each | 6 | 6,937.9 | 41,627.4 |
| 113 | Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) | Kg | 580 | 495.05 | 2,87,129 |
| 114 | Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) | Kg | 545 | 598.6 | 3,26,237 |
| 115 | With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) | Sqm | 350 | 1,176.8 | 4,11,880 |
| 116 | Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. | Each | 3 | 528.85 | 1,586.55 |
| 117 | Powder coated minimum thickness 50 micron aluminium | Each | 6 | 109.3 | 655.8 |
| 118 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to paid separately) | Sqm | 46 | 5,325.9 | 2,44,991.4 |
| 119 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. | Sqm | 26 | 617.05 | 16,043.3 |
| 120 | Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface preparation, first layer of slurry of cement @ 0.488kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured. | Sqm | 300 | 688.9 | 2,06,670 |
| 121 | Providing & Applying high quality acrylic modified resin based texture of Dholpur/Red sand stone Pattern with anti algae and UV resistance properties to be applied as intermediate finish in desired pattern @ 43.04 kgs/10 sqm to form film of 1- 1.5 mm thickness after scrapping and properly cleaning the surface to remove loose particles from the plaster surface, followed by top coating with Premium Acrylic Smooth exterior paint with Silicone additives of required shade by two or more coats @ 1.43 litres/10sqm, complete as the direction of Engineer -in- Charge. | Sqm | 800 | 597 | 4,77,600 |
| 122 | Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2 mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T& P,scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors,SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured. | Sqm | 80 | 9,502.35 | 7,60,188 |
| 123 | Frame size 50 x 125 mm | Metre | 125 | 1,075.7 | 1,34,462.5 |
| 124 | 25 mm thick | Sqm | 43 | 3,889.15 | 1,67,233.45 |
| Schedule total | ₹7,65,29,516.8 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCCACS11_CompressPdf.pdf
ATTACHMENT
ANNEXURE-VA.pdf
ATTACHMENT
PG Format - Engg Ranchi New - Update
ATTACHMENT
GCC - 2022 - ACS 10 - Updated
ATTACHMENT
BidSecurity-BGformat.pdf
ATTACHMENT
Letter of Credit
ATTACHMENT
Telecom Circular 9-2023-New
ATTACHMENT
2018_CE-I_CT_9Date04_06_2018.pdf
ATTACHMENT
TelecomCircular9-2023-New.pdf
ATTACHMENT
GCC-2022-ACS10UpdatedC.pdf
ATTACHMENT
PGFormat-Engg.RanchiNew-21.11.2025.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .