CONSTRUCTION OF THE SUB DEPOT ROADWAYS WORKSHOP AT MOHINDERGARH IN DISTT. MOHINDERGARH (PDG. E.I. INTERNAL, POWER WIRNIG , STREET LIGHT - HIGH MAST ONLY).

Amount

Supply and erection of moulded case circuit breakers on wall or on existing pedestal including bonding to earth and necessary connections. 15 amp.to 60 amp. 415 V ,10 KA 3-phase.

250 amp. 415 V , 35 KA 3-phase.

Supply and erection of 3 mm thick mild steel sheet duly welded on existing M.S. angle iron frame for fixing the main switches etc. as required, duly painted with three coats of approved paint including one coat of red oxide.

Supply and erection of blanking sheet in existing distribution board.

Supply and erection of miniature circuit breaker / isolator 240 /415 V in the existing distribution board including making necessary connections.Miniature circuit breakers of 9 KA breaking capacity.SP MCB of 6 amp. to 32 amp.

SPN MCB of 9 KA breaking capacity 6 amp. To 32 amp.

TP MCB of 9 KA breaking capacity 6 amp. to 32 amp.

TPN MCB of 9 KA breaking capacity 6 amp. to 32 amp.

TPN MCB of 9 KA breaking capacity 40 amp. to 63 amp.

Supply and erection of Fittings and Accessories.Bakelite angle / straight button holder large size.

Erection only of 1x40 watts or 2x40 watts 1220 mm long /1x20 watts or 2x20 watts ,610 mm long fluorescent tube fitting directly on wall including necessary connections with 0.75 sqmm ( 24 / 0.20 mm ) PVC copper flexible cable for connecting the tube with the adjecent point.

Supply and erection of hexagonal M.S. box 1.60 mm thick having each side 8 cms , 7.5 cms deep top covered with M.S. lid by means of screws including 10 mm dia 30 cm long mild steel rod made into suitable suspension hook and erected in RCC slab for erection of fan , the bottom covered with 3 mm thick bakelite sheet with suitable holes , painting etc. complete with all labour and material required to complete the job.

Erection of ceiling fan complete with necessary earthing of fan and regulator including carriage from local railway station /goods transport /PWD store to the site of work.

Erection of exhaust fan complete with necessary earthing of fan and regulator including carriage from local railway station /goods transport /PWD store to he site of work.

Making suitable hole in the wall upto 450 mm sweep exhaust fan including finishing the same and fixing of wire mesh duly fixed with Deodar wood frame of section 40 mm x 25 mm thick.

Pdg. and fixing of required size of deodar wood frame of section 50 mm x 32 mm for fixing exhaust fan upto 450 mm sweep.

Supply and erection of pipe for wiring purposes including bends inspection boxes etc. where necessary and painting as required. Heavy guage welded conduit pipe 20 mm dia 1.60 mm thickness flushed.

Heavy guage welded conduit pipe 25 mm dia 1.60 mm thickness flushed.

Supply and erection of PVC pipe of 6 kg. pressure laid 1 metre below ground level complete including digging refilling of the trench with jointing etc. PVC pipe 80 mm dia.

PVC pipe 65 mm dia.

Earthing with GI earth pipe 4.5 m long and 40 mm dia with masonry enclosure on the top etc. as required .

Extra for using salt and charcoal / coke for pipe earth electrode as required.

Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.

Extra for charcoal or coke and salt for G.I. Plate or copper plate earth electrode.

Supplying and laying of 25 mm x 5 mm G.I. Strip at 0.50 metre below ground level as strip earth electrode including soldering etc. as required .

Pdg. and fixing 25 mm x 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode as required .

Pdg. and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15 mm dia G.I. pipe from earth electrode as required .

Pdg. and fixing 25 mm x 5 mm G.I. Strip on surface or in recess for connections etc. as required with all labour and material.

Pdg. and fixing 4.00 mm dia G.I.wire on surface or in recess for loop earthing as required .

Supply and erection of 20 mm x 3 mm thick G.I. tape fixed with suitable G.I. stapples of same size.

Supply and erection of under ground cable 1 metre below ground level covered with sand and bricks including necessary connections,digging and refiling of trenches. 70 Sq. mm 3.5 Core Cable Ard..

Supply and erection of under ground cable, loose in existing pipe or trenches complete with necessary connections . 16 Sq. mm 2 Core Cable . Ard.

16 Sq. mm 4 Core Cable . Ard.

25 Sq. mm 3.5 Core Cable Ard..

70 Sq. mm 3.5 Core Cable . Ard.

Supply and erection of suitable compression type brass cable glands for underground Cable. 10 Sqmm to 16 Sqmm Cable 2 to 4 Core .

25 Sqmm to 50 Sqmm Cable 2 to 4 Core.

70 Sqmm to 95 Sqmm Cable 3 to 3.5 Core .

Supply and erection of weather proof M.S.Box of size 20 cm x 15 cm x 10 cm. covered with 3.00 mm thick M.S.sheet hinged cover, locking arrangemrnt , housed in wall , including the cost of 1 no. 16 amp. 415 volts kit-kat and 2 nos. 63 amp. 415 volts neutral links fixed on hard wood board in the M.S.Box including painting and necessary connections .

Supply and erection of Godrej Almirah typeM.S.pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S.sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- M.S.pedestal of size 750 mm wide , 900 mm high , 300 mm deep and bottom totally open , duly embeded in cement concrete block of size 900 mm x 450 mm x 200 mm above ground level duly plastered with 12 mm thick 1:4 cement plaster , having a base of size 1050 mm x 600 mm x 250 mm below ground level .

PVC Insulated wiring in recessed conduit. Wiring in 1.5 sq.mm PVC Insulated copper conductor cable in 1.6 mm thick conduit pipe.Fan Point Medium .

Light point Short.

Medium.

Twin control light point with 2 way 5 amp. single pole switch

Short point.Long point.

Call bell point including M.S box of size 180 mmX100 mmX 60 mm deep for Call bell Long point

3 pin 5 amp. plug point including earthing the 3rd. pin etcShort point.

Medium point.

Long point.

3 pin 15 amp. plug point including earthing the 3rd. pin etc. with 4 sq mm PVC insulated copper conductor cable. Long point.

Supply and erection of PVC unsheathed copper conductor cable single core 1100 volts grade in pipe of suitable size excluding cost and erection of pipe.Size 1.50 sqmm (3 / 0.81mm).

Cable size 2.5 sq.mm(3/ 1.05 mm)

Cable size 4.0 sq.mm(7/ 0.85 mm)

Supply and erection of M.S Saddles and clamps on wall/RCC parapit for fixing the under ground cable at a distance of .60 metre centre to centre fixed by means of rawl plug including the cost of all labour and material required to complete the job in all respect.

Supply and erection of MS stand made of 50mmx50mmx6mm angle iron frame and 150cm long, 30cm wide with MS sheet covering size 30cmx30cm 3.15mm thick fixed on the top of board & legs duly embedded in 1:2:4 cement concrete block 30cm below ground level including the cost of cement sand, welding, painting & fabrication charges etc. up to the entire satisfaction of Engineer - in - charge of the work.

Supply and erection of double door sheet steel enclosure distribution board suitable for MCBs and ELCBs etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-charge of work.4 way SP&N (Horizontal)

8 way TP&N (Horizontal) (8 +24)

8 way TP&N (Vertical) (8 + 24)

Supply and erection of 50mm diameter 1.5mtr. Long GI bracket (B-Class) making an angle 10 to 15 degree with horizontal plane for mounting street light fitting on GI bracket on wall with 2 Nos. 50mmx3mm thick MS flat including cost of cutting welding of GI pipe complete with cement sand mixture bolts and nuts etc. including making necessary connection with all labour and material required to complete the job in all respect up to the entire satisfaction of Engineer-in-charge of the work.

Supply and erection of Socket size rotary step type electronic regulator for A.C. ceiling fan Anchor make Deluxe model No.50440 ISI/SSK make PC 561 operated on 120/280 V A.C. supply complete including cutting of existing bakelite sheet and making necessary connection etc up to the entire satisfaction of Engineer-in-Charge of work.

Supply, installation, testing and commissioning of 16 mtr. long High Mast manufactured from B.S.E.N. 10025 or equivalent grade material in, 2 (two) section hot dip, galvanized inside and outside in single dip, suitable for wind velocity as per IS 875 Part-3 suitable for 9/12 nos. luminaire loading fully motorized (power tool) with starter & cable complete along with standard accessories supplied by the manufacturer with 3 nos. steel wire rope double drum system and twin dome aviation light with LED without foundation but including cost of set of foundation nut and bolts, installation at site complete in all respect upto entire satisfaction of Engineer -in-Charge

Provision for suitable foundation for 16 mtr. High mast. (As per PWD specification complete in all respect)

Supply and erection of 200 watt. Flood light fitting with all accessories as supplied with the fitting by manufacturer including erection of same on 16 mtr. high mast with anecessary nuts & bolts and making necessary connection complete in all respect upto entire satisfaction of Engineer - In- Charge.Make: Havell's/ Bajaj/ Crompton / Phillips /C&S

Supply and erection of time switch with contactor.

Supply and erection of 80W Energy saving robust Highway / Mediumbay LED IP65 luminaire complete with in all respect.Make : Havell's / Bajaj/ Crompton / Phillips

Supply and erection of 60 watts LED street light fittng made up of pressure die cast aluminium housing with high power LED as lighting source and lense embded PC cover having Top opening seprate driver compartment with IP 66 protection, with all labour and material required to complete the job in all respect upto entire satisfaction of Engineer - In- Charge. Make : Havell's / Crompton / Phillips /Surya

Supply and erection of Air circulator wall fan 24" complete with in all respect., Make : Orient / Crompton / Usha / Bajaj

shree shyam associates

GENERAL ENDEAVOUR