SPL REPAIR TO LT PANEL AND CONVERSION OF OH TO UG LT CABLE AND ALLIED WORKS AT OTM-I OF 4 BIHAR AT SRI GANGANAGAR MIL STATION

Amount

Supply, laying & testing cable XLPE insulated, screened ,PVC bendded galvanized steel strip or wire armoured electric power cables (heavy duty) with stranded aluminium conductor 1100 volts grade, of size 3.5 core 95 sq mm complete all as specified and directed by Engineer-in-Charge.

Supply, laying & testing cable XLPE insulated, screened ,PVC bendded galvanized steel strip or wire armoured electric power cables (heavy duty) with stranded aluminium conductor 1100 volts grade, of size 70 sq mm. 3.5 core complete all as specified and directed by Engineer-in-Charge.

Supply, laying & testing cable XLPE insulated, screened ,PVC bendded galvanized steel strip or wire armoured electric power cables (heavy duty) with stranded aluminium conductor 1100 volts grade, of size 50 sq mm. 3.5 core complete all as specified and directed by Engineer-in-Charge.

Supply, laying & testing cable XLPE insulated, screened ,PVC bendded galvanized steel strip or wire armoured electric power cables (heavy duty) with stranded aluminium conductor 1100 volts grade, of size 25 sq mm. 4core complete all as specified and directed by Engineer-in-Charge.

Supply, laying & testing cable XLPE insulated, screened ,PVC bendded galvanized steel strip or wire armoured electric power cables (heavy duty) with stranded aluminium conductor 1100 volts grade, of size 16 sq mm. 4core complete all as specified and directed by Engineer-in-Charge.

Supply, laying & testing cable XLPE insulated, screened ,PVC bendded galvanized steel strip or wire armoured electric power cables (heavy duty) with stranded aluminium conductor 1100 volts grade, of size 10 sq mm. 4core complete all as specified and directed by Engineer-in-Charge.

Supply, laying & testing cable XLPE insulated, screened ,PVC bendded galvanized steel strip or wire armoured electric power cables (heavy duty) with stranded aluminium conductor 1100 volts grade, of size 10 sq mm. 2core complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches, not exc 1.5 m wide and n. exc 1.5 m depth; or n exc 10 Sqm on plan and n exc 1.5 m in depth for foundations of poles, struts, stays etc. or laying underground cable etc. in soft/loose soil, & getting out including taking out old brick or precast cable cover for reuse complete all as specified and directed by Engineer-in-Charge.

Add to item No. 8 (Excavation in trenches) for Each additional 1.5 Mtr OR part thereof in depth beyond the first 1.5 Mtr

Returning, filling in, excavated soil including spreading, levelling, watering and well ramming in layers n.exc 25cm thick complete all as specified and directed by Engineer-in-Charge.

Removal of excavated surplus soil to a distance n.exc 50m and depositing where directed at level not exceeding 1.5 m above the starting point complete all as specified and directed by Engineer-in-Charge.

M & L for sand cushioning with dry coarse sand to under ground cable around the cable after laying the cable complete all as specified and directed by Engineer-in-Charge. Note : Thickness after punning shall be considered for payment.

M & L for brick protection with old size sub class 'B' bricks laid flat , length of bricks across the route of underground cable complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation for poles, stays & mass concrete complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in foundation for poles, stays & mass concrete complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:2:4) type B-2 using 20mm graded stone aggregate as in pedestal coping of poles etc including weathering, slightly rounded or chamfered angle and necessary form work and fair finishing alll exposed faces of concrete without using extra cement complete all as specified and directed by Engineer-in-Charge.

Supplying, Erecting in true vertical position of 9 Mtr long ,type 410 SP- 31 Steel tubular pole complete with cast iron base plate, finial taper plug, bolts nuts and screws including painting with two coat of synthetic enamel paint black and yellow in alternate strips 30cm each up to 1.5 meter height from top of PCC coping and remaining portion of pole shall be painted with two coats of aluminum paint including writing pole No. with black synthetic enamel paint over 15 cm dia. yellow round base prepared with synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. NOTE: - Excavation, earth work and concrete work for embedding poles shall be measured and paid separately.

Supply and fixing street light bracket made out of 40 mm dia GI tubing medium grade made to shape 1.5 Mtr long with fixing arrangements for LED fitting duly painted with two coats of synthetic aluminium paint over a coat of primer including MS clamp and back plates fabricated from steel section including nuts, bolts, washer etc complete all as specified and directed by Engineer-in-Charge.

S&F 45 Watt LED Street light luminaire comprising of epoxy powder Die-cast aluminum housing with weather proof gasket for lamp & driver compartment complete fitting with all accessories and following specifications complete all as specified and directed by Engineer-in-Charge. (a) Lumen sys efficacy of luminair should be minimum 105 Lumen per Watt (b) Input voltage range : 140 to 270 volts (c) Temp operating range : Minus 10 degree C to Plus 50 Degree C. (d) Power Factor : Min 0.95 (e) THD : Max 10% (f) CRI : Morethan 70 and CCT : 5700 K (g) IR Rating : Min IP 65 (h) IK rating : Min IK 07 (j) Built in potted LED driver of the same make as of the luminaire. (k) Surge protection 10 KV (inbuilt + Extended) (l) Lens : High Efficeiency sec wide angle lens. (m) BIS approved fixture and Driver. (n) Rated life time : 50000 burning hrs (Avg 10 to 16 Hrs daily) (o) LED driver should be complete with all protections viz open / short circuit protections, over voltae protection, all as per standared design of manufactrure. Driver shall be of same make as that of fitting.

Supply, install, test and commisioning of LT panel duly powder coated of suitable size outdoor cubical type factory made, weather & vermin proof made out of CRCA sheet 3.15mm (outdoor type) thick machine pressed with bottom frame made out of angle iron 50mm x 50mm x 6mm and 600mm long 4 legs duly painted with 2 coats of synthetic enamel paint over a coat of red oxide primer on exposed surfaces grouted in PCC 1:2:4 type B1 using 20mm graded stone aggregate blocks of size 30cm x 30cm x 60cm and 100mm thick PCC (1:2:4) type B1 floor over 100mm thick sub base of brick hardcore extended 100mm on all sides below panel body complete and suitable for 415 Volt AC 3 phase, 4 strip having insulated Copper bus bar 400 Amps from pole with openable double shutter on both sides (rear and front side) with locking arrangment duly pre-wired with suitable size of copper conductor cable fitted with Incomingproper size copper lugs/thimbless and connecting the incoming and outgoing MCCBs with suitable size strip duly bended and drilled and fixed with nuts, bolts & washers from bus bar to MCCBs etc duly fitted with and including the following accesories & all connected iems complete all as specified and directed by Engineer-in-Charge. FP No1 Incoming (i) MCCB 200 Amps, four pole with fixed thermal magnetic release, 415 V AC supply, having rupturing capacity 36 KA - 01 No Outgoing (ii) MCCB 100 Amps, Four pole with fixed thermal magnetic release, 415 volts having rupturing capacity 25 KA -4Nos (01 Nos Spare) (iii) 32 Amp TPN - 01 Nos (iv) 25 Amp SPN - 02 Nos(v) Indicating lamps set RYB - 01 Set (VI) Digital Amp Meter 0- 250 A with CT , Digital Voltmeter 0- 500 V

Supply, install, test and commisioning of LT panel duly powder coated of suitable size outdoor cubical type factory made, weather & vermin proof made out of CRCA sheet 3.15mm (outdoor type) thick machine pressed with bottom frame made out of angle iron 50mm x 50mm x 6mm and 600mm long 4 legs duly painted with 2 coats of synthetic enamel paint over a coat of red oxide primer on exposed surfaces grouted in PCC 1:2:4 type B1 using 20mm graded stone aggregate blocks of size 30cm x 30cm x 60cm and 100mm thick PCC (1:2:4) type B1 floor over 100mm thick sub base of brick hardcore extended 100mm on all sides below panel body complete and suitable for 415 Volt AC 3 phase, 4 strip having insulated Copper bus bar 200 Amps from pole with openable double shutter on both sides (rear and front side) with locking arrangment duly pre-wired with suitable size of copper conductor cable fitted with Incomingproper size copper lugs/thimbless and connecting the incoming and outgoing MCCBs with suitable size strip duly bended and drilled and fixed with nuts, bolts & washers from bus bar to MCCBs etc duly fitted with and including the following accesories& all connected items complete . Incomming (i) MCCB 100 Amps, four pole with fixed thermal magnetic release, 415 V AC supply, having rupturing capacity 25 KA -01 Out going (ii) MCCB ,4 pole 63 Amp -03 No (01 Nos Spare) (ii) TPN 32 Amp -02 No (iii) SPN 25 Amp -02 Nos (iv) Indicating lamps set RYB - 01 Set (v) Digital Amp Meter 0- 200 A with CT , Digital Voltmeter 0- 500 V

Supply and fix shock ,rust proof fire retarddant class FV-0 as per IS-11731 Part II or V-0 as per UL -94 ,high heat distortion temperature FRP juction box of size 300 x200x105 mm with locking arrangement made out of 3 mm thick PVC sheet including provision of 4 nos aluminium busbar of size20 mmx3 mm mounted on insulator 01 nos MCB 1 A SP 10 KA 240 volt , drilling holes for outgoing and incomming cable ( 2 way) connection with suitable lugs and glands including provision of clamp made out of 40 x5 mm thick mild steel flat iron complete all as specified and directed by Engineer-in-Charge.

S&F on pole/wall/in panel, Sheet metal enclosure Bus bar chamber consisting 04 pole 100 Amp 415 volts copper bus bar Each Set suitable for connecting cable as a (junction incoming & outgoing total No 4 ways) including connecting of existing cables with suitable sizes aluminum thimbles complete all as specified and directed by Engineer-in-Charge.

M & L for Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried in ground (earth pit not less than 2.25 Mtr deep below normal ground level with top edge of the plate not less than 1.5 Mtrs below normal ground level, connecting to the Galvanised iron earth lead 32 x 6 mm size by means of bolts, nuts check nuts and washers of galvanised iron and 32 x 6 mm dearth lead protection by provision of GI medium grade pipe 40 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20mm graded stone aggregate with 40mm thick cover of RCC (1:2:4) reinforced with XPM (wieght not less than 4gs/Sqm) and frame of angle iron 25mm x 25mm x 6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed on top edge of earth plate common salt and charcoal filling test point made out of 40mm x 8 mm FI with fixing arrangements, funnel, wire mesh and earth work in hard dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 Mtrs and connecting to earth test point all as specified or indicated including testing on completion complete all as specified and directed by Engineer-in-Charge.

M & L for Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried in ground (earth pit not less than 2.25 Mtr deep below normal ground level with top edge of the plate not less than 1.5 Mtrs below normal ground level, connecting to the Galvanised iron earth lead 4.0 mm size by means of bolts, nuts check nuts and washers earth lead protection by provision of GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20mm graded stone aggregate with 40mm thick cover of RCC (1:2:4) reinforced with XPM (wieght not less than 4gs/Sqm) , GI light grade 20mm bore pipe for watering perforated at the bottom 7.5 meter long placed on top edge of earth plate common salt and charcoal filling test point , funnel, wire mesh and earth work in hard dense soil and connecting to earth test point as specified or indicated including testing on completion complete all as specified and directed by Engineer-in-Charge.

Boring of holes under road/pavement/hard standing or any other situation by manual mean and including passing GI pipe 80 mm bore and making good both the ends complete all as specified and directed by Engineer-in-Charge. . Note : Pipe and cable will be measured and paid separately

Supply and fix in replacement of GI pipe 80 mm bore light grade for protection of cable including provision of clamps, nut, bolts etc required for fixing pipe along pole / wall / laid under the road / laid under the floor or in trenches complete all as specified and directed by Engineer-in-Charge.

Supply and fix in replacement of GI pipe 50 mm bore light grade for protection of cable including provision of clamps, nut, bolts etc required for fixing pipe along pole / wall / laid under the road / laid under the floor or in trenches complete all as specified and directed by Engineer-in-Charge.

Supply and fix PVC insulated and FR PVC Round sheathed Copper conductor (flexible) industrial cable, 1100 volt, size 1.5 sq mm, 3 core, conforing to IS 694 for connection of fitting from junction box to light fitting complete all as specified and directed by Engineer-in-Charge.

Dismanting of unserviceable ACSR conductor/AAC conductor of any size and any type complete all as specified and directed by Engineer-in-Charge.

Dismanting of cross arm, clamps , bracing etc of MS section complete all as specified and directed by Engineer-in-Charge.

Dismanting of insulator any type and size complete all as specified and directed by Engineer-in-Charge.

Dismanting of old PCC Pole any type and size complete all as specified and directed by Engineer-in-Charge.

S & F of Automatic Street Light Control Switch using Infrared Sensor based Nature Switch for automatic switching of street lights. Nature Switch operation should be based on Natural Lux Level. Required Illuminance level for switching On is <= 30 Lux and for switching OFF >=10 Lux. The Circuit should be suitable enough to take Thre phase load of 5 KW with 3 nos Contactors, 3 nos incoming MCBs& 3 nos Outgoing MCBs of 16-20 Amps each & circuit wiring (Copper) of min 10 sqmm. complete all as specified and directed by Engineer-in-Charge. (Make : Swadeep -66- 5KW3P/ or equivalent in / Indo Asain/ Bajaj/L&T/C&S.

Dismanting of Existing 1.2 Mtr GI Pipe with S/L complete all as specified and directed by Engineer-in-Charge.

Note :(i) Amount of credit for retrieved materials is mentioned in Sch 'A' Section-II of tender documents in pdf form which will be deducted while acceptance of tender offline.

M/S SHREE SHYAM TRADERS

M/s JUGAL KISHORE MISHRA AND SONS

SILEWAL CONTRACTOR & SUPPLIER

NISHTHA BUILDERS

DASHMESH ENTERPRISES

Singla Electricals

M/s NIRMAN BUILDERS

M/S BUDHRAM BISHNOI

UNITED ENGINEERING CORPORATION