SPL REPAIR OF OR GOVT MD ACCN, BLDG NO 349 (01 TO 04) AND SPL REPAIR TO BLDG NO 160/09 TO 12 AT ZORAWAR MARG AT ITARANA CANTT ALWAR

Amount

Demolition cement concrete (unreinforcement) in ground floor and paving n exc 15 cm thickness (below or above ground level) & removal complete all rubbish materials as directed by Engr-in-Charge and all as specified. Note : (i) Remove salvage from the MoD land without any extra cost. (ii) Quoted rates is deemed to be inclusive of cost of executing the work at any height in (G+1) bldg.

Demolition of cement concrete (reinforced) in landing slab, chullah hoods, manhole covers, Roofs, Floors, beams, stair case, landing, chajja and similar suspended work. Note : (i) Remove salvage from the MoD land without any extra cost. (ii) Quoted rates is deemed to be inclusive of cost of executing the work at any height in (G+1) bldg.

Demolition of brick work or stone/boulder masonry built in cement mortar incl all quoins, arches, pillars & precast concrete masonry etc complete all as specified & directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n exc 1.5 but each complete all as specified & directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 but n exc 4 sqm each complete all as specified & directed.

Cutting holes into stone wall built in cement mortar or cement lime mortar for inserting hold fast and making good dismantle portion in CM (1:3) or cement concrete (1:2:4) type B-1 exc one brick but n exc two brick as required all as directed by Engr-in-Charge.

M&L 50mm thick cement concrete 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in plinth protection path laid in panel surface finished even and fair without using extra cement and Joints of panel should be filled by bituminous primer complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded aggregate as in cills, coping steps, tank staging, seismic and other similar courses, lacing courses parapet and railing upto 60cm ht kneeler kerb and alike including weathering, slightly rounded or chamfered angle and throating as directed.

M&L for PCC (1:4:8) type D-2 (Using 40mm stone aggregate) as in foundation concrete all as specified and directed.

M&L for Reinforcement cement concrete 1:2:4 type B-1 Nominal mix as in landing, cover slabs (for manholes etc) Chajjas, water troughs, managers, shelves and Similar article with plain faces.

M&L plain cement concrete 1:2:4 type B0 in roof kerbs or mud stops, rounded or chamfered on edges

M&L rendering 15mm thick in CM 1:4 on fair faces of on stone/Brick masonry including WPC @ 3% by weight of cement finished even and smooth without using extra cement including taking down old existing plaster/Pointing of any type complete all as specified and directed. Note : (i) Remove salvage from the MoD land without any extra cost. (ii) Quoted rate is deemed to be inclusive for work at any height and location including cost of scaffolding and all other equipments reqd to execute the work.

M&L rendering 15 mm thick in CM 1:6 on Brick/stone masonry surfaces or on other than fair faces of brick masonry finished even and smooth without using extra cement including taking down cement or cement lime plaster of , any description on brick or stone walls, etc including racking out joints, hacking for key,scrubbing down with water etc, complete all as specified and directed. Note : (i) Remove salvage from the MoD land without any extra cost. (ii) Quoted rate is deemed to be inclusive for work at any height and location including cost of scaffolding and all other equipments reqd to execute the work.

M&L rendering 5mm thick in CM 1:3 on concrete ceiling surfaces finished even and smooth without using extra cement including taking down cement or cement lime plaster, any description onconcrete surfaces etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. Note : (i) Remove salvage from the MoD land without any extra cost. (ii) Quoted rate is deemed to be inclusive for work at any height and location including cost of scaffolding and all other equipments reqd to execute the work.

M&L rendering 15 mm thick in CM 1:6 on stone masonry surfaces or on other than fair faces of brick masonry finished even and smooth without using extra cement , any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. Note : Quoted rate is deemed to be inclusive for work at any height and location including cost of scaffolding and all other equipments reqd to execute the work.

M&L rendering 15mm thick in CM 1:4 on fair faces of on stone/Brick masonry including WPC @ 3% by weight of cement finished even and smooth without using extra cement complete all as specified and directed. Note : Quoted rate is deemed to be inclusive for work at any height and location including cost of scaffolding and all other equipments reqd to execute the work.

M&L for Rough cast plaster on exterior walls applying the under coat of cement and sand morrtar 1:3 not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm ) mixed with coarse sand and cement in the raio of 1:1:1 shall be applied and finished even. The mix of cement and sand shall made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered including dismantling old existing plaster/pointing complete all as specified and directed by Engineer in Charge

Taking down carefully existing bitumen tarfelt including plaster of any description over the surfaces of roof, terraces including flashing and junction of parapets/curve walls etc and removing of the rubbish and depositing where directed complete all as specified and directed

M&L for 20mm thick screed bed on fair faces of concrete/brick surfaces in CM 1:4 with water proofing compound @ 200ml per bag of cement even and smooth in order to maintain proper slope over existing roof surfaces for laying APP based polymeric membrane finished complete all as specified (Polymeric membrane and WPC shall be meausred and paid separately here-in-after)

Supply only integral water proofing compound.

M&L water proofing treatment to RCC roof slab including parapet comprising of following course of treatment/specified from bottom to top (a) Applying Bituminous primer @ 0.40 Ltr per sqm over plastered surfaces of roof including parapet surfaces. (b) Over the priming coat laying one layer APP based polymeric membrane of approved manufacturer, 3 mm thick weight not less 3.6 Kgs/Sqm and upper side of membrane laid down including a layer of bitumen 85/25 @ 1.20Kg/Sqm used, it shall be laid by torch application side overlap should be 75mm and end shall be 100mm. For parapets, membrane shall be taken to a height of minimum 20cm and then inserted inside parapet in groove. The same shall be finished by a membrane flashing & applying two coats after cool roof paint "as per manufactruer instructions".

M&L for Providing cement concrete type B-0, 1:2:4 (using 12.50 graded stone aggregate) as in padding and leveling course on roof and floor complete all as specified & directed.

M&L taking down and removal of loose / disintegrated old concrete up to 50mm depth/ plaster and cleaning all loose dust washing with water and epoxy bonds materials of pidilite/Dr fixit bind new cement plaster /polymer modified plaster/concrete /screed concrete wth old surface etc complete

M&L applying 15mm thick plaster with polymer modified mortar fortified with SBR in proportion 1:3 by weight 5 litres Nit bond SBR 45 to added to 50kg cement with 13 litre water addition finished surface to match with existing adjoining surface of ceiling, beams and a like complete over. M&L for bonding agent as per Manufacturer instruction complete all as spd and directed

M&L and applying two or more coats of 2 component zinc based epoxy rust preventer on corroded reinforcement after cleaning and removing the rust from corroded reinforcement with the help of wire brush and treating it with rust remover (Reebaklens RR) including thoroughly cleaning washing air blowing brushing etc complete. Note : Qty of zinc based epoxy rust prevent or only shall be taken into account for payment purpose on the basis of actual consumption.

M&L for glazed ceramic colour tiles in vertical surface 450X 300X 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 10 mm thick rendering in CM (1:4), including dismantling old tiles complete all as specified and directed.

M&L non skid ceramic coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 300mm x 300mm in floor etc, set and jointed in neat cement slurry and pointed in white and coloured cement to match coloured tiles including Screed bed of mortar 15mm thick for laying floor finishes CM (1:6) including dismantling old tiles complete all as specified

M&L non skid ceramic coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 400mm x 400mm, in floor etc, set and jointed in neat cement slurry and pointed in white and coloured cement to match coloured tiles including Screed bed of mortar 15mm thick for laying floor finishes CM (1:6) including dismantling old tiles complete all as specified

All as per ser item No 28.00 above but as in skirting/dado including 10mm thick cement mortar 1:4, complete all as specified and directed

M&L for machine cut green marble flooring 15 to 18mm thick as in floor, cooking platform, treads etc laid over and including 20mm screed bed or bedding layer in CM 1:3 set and jointed in neat cement slurry and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing by machine and including dismantling old stone slab complete all as specified and directed.

M&L for machine cut Green Marble 15 to 18mm thick as in riser of steps, skirting, dado and pillar set over 10 mm rendering in CM 1:3 and jointed with grey cement slurry mixed with pigments to match the shade including rubbing and polishing including dismantling old stone slab complete all as specified by Engr-in-Charge.

M&L for 18 to 20 mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over 15 mm screed bed or bedding layer in CM 1:3, including grinding of edges to curved surface finish including dismantling old stone slab complete all as specified and directed.

M&L for cutting holes in stone /RCC/granite slab for inserting cooking gas cylinder pipe and making good complete all as directed

M&L mild steel framed work as in door frames for gates & section for gauge/fly proof shutters made of angle or hallow/square/rectangular/circular section and other covering door to be prepared for handing or sliding with including either hooks , proportionally made sliding door bolt , hinges or handles fittings (exclusive of steel or other covering, running rails and guides) and hanging also fastening and fixing , necessary arrangements for fixing of wiremesh, necessary bolting including welding complete conforming to FE-290 Gde E-165. Wire gauge will be measured and paid separately

S&F Aluminium windows/Ventilators made of 1.59 thick powder coated (thickness of powder coating not less than 50 micron) as per aluminium section of size given below. Aluminium window will be of double shutter of glass/ wire gauge shutters including all necessary accessories jointing cleats, glazing clips, rubber neoprene packing, for fixing glass/ wire gauge, aluminium handles and tower bolt 2 Nos 100 mm ‘D’ Type in each door, 2 Nos 100 mm aluminium hinges including necessary steel screws complete all as specified and directed by Engr The size of different aluminium section to be used is as under (a) Outer Frame 125X45X2.00 mm thick (b) shutter frame section size 44X44X1.59 mm thick for glass and 44x25x1.59mm for wire gauge Note: Rates quoted are inclusive all fittings and fixtures. Glass and wire gauge & MS grill will be paid separately in respective items.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples to wooden/steel frames with beading complete all as specified & directed.

S&F sheet glass, ordinary quality 4.80 mm thick fixed with rubber beading and clips size of glass n.exc 2 sqm in each pane complete all as spd & directed.

S&F 5.0mm Figured glass, pin head type and glazings with rubber beading and clips size of glass n.exc 0.50 sqm in each pane complete all as spd & directed.

S&F frame work such as grills, grating etc, with ends of bars shouldered &/or riveted or forged into spikes, framed guard bars, barred iron door ladder, frame balusters, walk ways, railing, frame work or water tanks & Similar work conforming to Fe-290 Gde E-165.

S&F in repair vitreous china squatting pan of Orrisa pattern size 580mmx440mm white with integral foot rest (excluding flushing cistern and flush pipe complete including provision of lime concrete bedding.

Supply and fixing in repair PVC flushing cistern low level 10 ltr cap with inlet ball valve float and handle symphonic action type incl brackets and flush pipe of polythene of low or high density.

S&F in repairs 15 mm bore fancy type long body bib tap with wall flange chromium plated with capstan heads, chromium plated, screwed for iron pipe or for brass ferrule, complete all as specified & as directed.

S&F in repairs 15 mm bore short body bib tap with wall flange, chromium plated with capstan heads, chromium plated, screwed for iron pipe or for brass ferrule, complete all as specified & as directed.

S&F in repairs Stop valves/angle cock bore of pipe in 15mm, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repairs, 15mm bore, concealed stop valve, chromium plated, fancy type, with long shank, and cup (Concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions etc complete all as specified and directed.

S&F in repair over head shower (fancy type) chromium plated 100mm round shape single flow (ABS body) with or without swivel joints, including fixing to steel pipe or union all as specified and directed.

S&F in repair vitreous china corner wash hand basin of Size 550x435mm/400x450mm excluding taps waste chain plug stopper but incl brackets incl waste pipe cutting pinning in ends of brackets complete.

S&F in repair 15mm dia bore cast copper alloy chromium plated fancy type pillar tap without cold & hot water complete all specified and as directed.

S&F in repair 32 mm dia PVC flexible waste pipe for WHB/Sink 600 mm long with PVC coupling all as directed fixed in repair..

Taking up or down steel tubing and connections including cleaning for refixing or removal to store 20mm bore pipe.

Refixing old steel tubing and connection in new or old position (walls, ceiling, floor etc) bore of pipe in 20mm dia.

S&F tubes medium grade 'galvanised' with and including all fitting and fixed bore of 20 mm dia complete to walls and ceiling or laid in floors of 20 mm bore.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store 15mm bore pipe.

Refixing old steel tubing and connection in new or old position (walls, ceiling, floor etc) bore of pipe in 15mm dia.

S&F concealed tubes medium grade 'galvanised' with and including all fitting and fixed bore of 15mm dia complete to walls and ceiling or laid in floors of 15mm bore.

S&F in repairs sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including fixing in granite bowl size 410mm x 330mm x160 mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, including taking down old unserviceable sink.

S&F in repair 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

Dismantling of water tanks of capacity exc 250 but n exc 500 ltrs & removing to stores complete all as specified & directed.

S&F 500 ltrs capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified & directed .

S& Fixing in repair ball valve brass high pressure with polythene float and fly nut screwed on iron pipe ad fixed 20 mm bore of pipe

S&F in repair PVC connection 15mm size with PTMT nuts of length 600mm.

S&F in repair Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges

S&F in repair Floor Drainer with Collar and Cockroach Trap/Jali with or without waste hole all as specified and directed

S&F in repair brass chromium plated soap dish, complete all as specified.

S&F in repair brass chromium plated towel ring incl a pair of CP brass bracket complete all as specified and directed by Engr-in-Charge.

S&F in repair CP brass mixer for Wall mixer hot & cold water for screwed down for iron pipe and fixed bore of pipe in 15 mm.

Cutting Chases exe 10 cm but n exc 20cm in girth in brick/stone wall for fixing of PVC Pipe/GI pipe of 15 & 20 mm bore (concealed in wall) including making good surface in CM (1:6) & to match with the existing surfaces.

S&F in repair PVC (SWR) pipes of 75 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.8 mm) single socketed in any length with rubber ring joints laid in trenches or in floors of 75mm pipe i/c taking out old u/s PVC/CI pipe with fittings

S&F in repair PVC (SWR) pipes of 110 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.8 mm) single socketed in any length with rubber ring joints laid in trenches or in floors of 75mm pipe i/c taking out old u/s PVC/CI pipe with fittings

S&F in repair PVC (SWR) pipes of 75 mm bore single socketed in any length fixed to wall i/c taking out old u/s PVC/CI pipe with fittings

S&F in repair PVC (SWR) pipes of 110 mm bore single socketed in any length fixed to wall i/c taking out old u/s PVC/CI pipe with fittings

S&F in repair PVC (SWR) floor trap, plain with grating including joining with solvent cement 100 mm dia.

S&F in repair PVC (SWR) Nahani trap, plain with grating including joining with solvent cement 75 mm dia.

S&F in repair PVC (SWR) bend 75mm bore of any radius

S&F in repair UPVC (SWR) bend 75mm bore of any radius with access door

S&F in repair PVC (SWR) bend 110 mm bore of any radius

S&F in repair PVC (SWR) bend 110 mm bore of any radius with access door

S&F in repair PVC (SWR)single junction PVC (SWR) (Single T) equal or unequal of 110 mm bore with access door

S&F in repair PVC (SWR) double junction PVC (SWR) (Double T) equal or unequal of 110 mm bore with access door

S&F in repair PVC (SWR) single junction PVC (SWR) (Single T) equal or unequal of 75 mm bore with access door

S&F in repair PVC (SWR) vent cowl 110 mm

S&F for Pipe Supporting Clamping - for GI pipe 2 Nos for 15mm and 2 Nos for 20mm down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt R/M System running vertically with wall distance 3": Pipe Support Clamping made of 1. Profile Bracket having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921 and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted "C" Channel with ribs to be used of size 10" made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 3" - 2 Nos. 2. Continuous Slotted C Channel of Size 10" - 1 No.; 3. U Bolt R/M for 3" (75 mm) CI or PVC Pipe Dia. - 1 No.; and 4. Justi Khilla 2 1/2" Zn coated - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing No. : CE Jaipur Zone - Jaipur; TD/2022/102. Make: Shaivi or equivalent as approved by GE. complete all as specified and directed

S&F for Pipe Supporting Clamping - Single Pipe of dia 3" (75 mm) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt R/M System running vertically with wall distance 3": Pipe Support Clamping made of 1. Profile Bracket having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921 and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted "C" Channel with ribs to be used of size 10" made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 3" - 2 Nos. 2. Continuous Slotted C Channel of Size 10" - 1 No.; 3. U Bolt R/M for 3" (75 mm) CI or PVC Pipe Dia. - 1 No.; and 4. Justi Khilla 2 1/2" Zn coated - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing No. : CE Jaipur Zone - Jaipur; TD/2022/102. Make: Shaivi or equivalent as approved by GE. complete all as specified and directed

S & F for Pipe Supporting Clamping - Single Pipe of dia 4" (110 mm) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt R/M System running vertically with wall distance 3": Pipe Support Clamping made of 1. Profile Bracket having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted "C" Channel with ribs to be used of size 10" made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 3" - 2 Nos. 2. Continuous Slotted C Channel of Size 10" - 1 No.; 3. U Bolt R/M for 4" (110 mm) CI or PVC Pipe Dia. - 1 No.; and 4. Justi Khilla 2 1/2" Zn coated - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing No. : CE Jaipur Zone - Jaipur; TD/2022/102. Make: Shaivi or equivalent as approved by GE.

Demolition and breaking up drain pipes (Salt glazed stone ware, AC, or Reinforced concrete) or 100mm dia set in cement mortar including PCC bed to drain pipe, packing under & hunching against the sides of drain pipes all as specified & directed by Engineer-in-charge.

S&F for 75mm thick steel fibre reinforced (SFRC) man hole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard, minimum load bearing capacity 5 ton/sqm, in square, rectangular or circular shape complete all as specified & as directed.

M&L 150mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars including demolition and breaking up old existing pipe all as specified & as directed.

M&L for Concrete bed for 150mmdia drain pipes laid to falls including packing under and hunching against the sides of pipe after they are laid & tested in cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone agg.) complete all as specified and directed.

M&L for cutting into existing manholes / Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150mm bore pipe.

S&F extruded aluminum alloy with galvanized mild steel hing pin Butt hinges 100mm long

S&F SS sliding door bolt with hasp, staple (bolt type) 300mm long not less than 12mm dia with and incl minimum of 06 bolts and nuts, 4 on plate and 2 on staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, plate and fixed all as specified.

S&F SS barrel tower bolts of extruded section and fixed 150 mm long

S&F SS handles 125mm size fabricated type anodized ISI marked.

S&F SS barrel tower bolts of extruded section and fixed 200 mm long

S&F SS handles 150mm size fabricated type anodized ISI marked.

S&F mild steel butt hinges medium weight colod rolled of size 100mm, ISI marked complete all as specified and directed.

S&F 140 mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, with vulcanised rubber piece fixed in floor as directed

S& F in repair stainless steel plate rack out of 1.00 mm thick sheet of size 900 x 750 mm and depth of shelves 230 mm with partition for small /large plates made out of stainless steel 24 gauge all as per sample to be hanged on wall by the help of steel screws grouted in walls with rawl plug design as approved by GE.

M&L for pressed steel shutter 1mm thick including pressed steel frame of 1.25 mm thick sheet, 12mm dia M S rod for locking , two nos chromium plated handle and one mortise pattern lock incl two coats of spray painting over a coat of shop primer complete all as shown on drg no TD/2004/29 sheet no 1/3 to 3/3

S&F in repair mild steel, chromium plated curtain 15mm dia bore rod with fixing bracket, stops, rollers etc complete all as specified and directed.

S&F in repairs Stainless Steel drapery rod of 25 mm inner dia (in length as directed ) of approved colour with & including matching finials at both ends and pair of SS brackets fixed at both ends with PVC rawl plug & steel screws on walls/beams including PVC curtain rings of matching colour @10 cm c/c all as specified and directed

M&L for 50mm thick sand stone slab in sunshades, chajjas, shelves, cills, landings, cover stones, templates etc not exc 2m in length, punched dressed on face and along exposed edges, self faced on the other SIde and set and pointed in cement mortar 1:4 complete.

M&L for TMT bars 10mm dia and over cut to length to shape required including cranking, bending spirally or hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9 mm dia all as specified.

All as per item 105 above but 6mm to 8mm dia TMT bars.

Excavating in trenches n exc 1.50m in width and n exc 1.50m in depth for foundation, manholes etc as well as n exc 10 sqmm on plan area and getting out in soft/loose soil all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n exc 25 cm thick in soft/loose soil.

Removing excavated soil to a distance exc 50m and depositing where directed at a level n exc 1.5m above the starting point.

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius, built in 1:4 as in half brick thick wall complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 mean radius, built in CM 1:6.

Dismantling structural steel work including doors, gates but excluding framed truss etc.

S&F Mild steel hand rails, half round or other stock section or core drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolt posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc and similar work conforming to Fe-290 Gde E-165.

S&F welded steel wire fabric n exc 4kg/Sqm complete to wood or steel membrane complete all as specified and directed

M&L for 75 mm thick PCC 1:4:8 Type D-2 (using 40 mm graded stone agg ) as in sub base of floor/pavings/path etc

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

Treatment of sunken portion is as follows :- (a) Demolition of lean concrete and other type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. (b) Maintain the Sunken to a slope of 1:40 outward with 32mm dia GI pipe spout projecting at least 150 mm beyond outer face of wall. (c) Top of the sunken floor slabs shall be laid to a slope 1:40. The surface of RCC slab shall be made even and smooth by using extra cement while the concrete is still green. Concave fillet in PCC (1:2:4) type B0 of radius 75 mm shall be provided at the junctions of RCC slab and adjoining walls. (d) Floor and side walls upto the finished floor level shall be plastered with 15 mm thick CM (1:4) mixed with water proofing compound @ 3% by weight of cement. Over plastered surfaces, a layer of APP based polymeric membrane not less than 3mm thick, weighing not less than 3 kg per sqm, reinforced with polyester non- woven fabric (weighing not less than 150 gm per square metre) shall be laid by torch application. Side overlaps shall be 100mm and the ends laps shall be 150 mm and overlap joints shall also be sealed by torch application. (e) The sunken portion shall be filled with lean cement concrete (1:5:10), type E2 using 40 mm brick aggregate after carrying out satisfactory testing of CI pipes / joints and slabs / walls by filling water for 72 hours. The sunken portion of Nahani / floor trap and pipe joints shall be embedded in PCC (1:3:6) blocks. (f) 32 mm dia GI spout shall be provided to drain out leakage, if any. (iii) Above aspects are deemed to be included in quoted rate. (iv) Horizontal floor area shall be measured for payment purpose.

S&F for preparation of new steel surface of any description over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls & applying two coats of oil emulsion distempering (OBD) over and including a coat of white wall care putty 1 mm thick complete all as spd and directed.

M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salt, trading oil grees spots etc using grinding machine on wall surfaces and preparation of old plastered wall surfaces and applying two coats of oil emulsion distemper (OBD) of approved shed/tint over and including a coat of white wall care putty 1 mm thick complete all as spd and directed.

M&L for preparing newly plastered surfaces & applying three coat of white wash on ceiling.

M&L for preparation of old surfaces and applying two coats of white wash on ceiling.

Material and labour for preparation of newly plastered surface of wall and applying two coat of water based premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology, Excellent Dirt Pick up resistance with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over priming coat with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in both the coats of paint over a coat of primer complete all as specified and directed. Make - Nerolac Excel Top guard (10 years product warranty)/ Asian Paints Ultima Protek (10 years product warranty)/ Berger weather coat long life 10 (10 years product warranty) at any height including necessary scaffolding.

M & L for writing letters or figures (Block, Roman, Italic or Indian) n. exc 30 cm height with thick synthetic enamel paint complete all as specified and as directed by Engr- in - Charge.

S&F factory made kitchen cabinet of size 1.5M x 0.60M x 0.3M, made out of 18mm thick PVC celuka sheet having density not less than 650kg/cum one side decorative lamination & other side balancing lamination sheet consisting of carcase 18 mm thick PVC sheet including shutters made out of 18 mm thick PVC board all required brackets 5.5 screws etc. The panels shall be fabricated using adhesive and screws where every required. All edge shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification mentioned as per drawing and specification approved by Engineer-in-Charge Note : (i) PVC celuka sheet manufactured by an ISO 9001-2015 certified company, termite proof, water proof & flame retardant PVC sheet. (ii) PVC cabinet of required size fabricated by joining four 18mm thick PVC celuka ply fixed with each other using solvent cement adhesive and screws and 18mm thick PVC sheet as backing of cabinet screw and solvent cement adhesive etc (iii) The Cabinet box will be divided into two equal part with two leaf shutter and one shelf will be placed in cabinate (iii) Cabinate will be fixed in wall with 4x fasteners etc and necessary fixing lugs (iv) Each shutter will be provided with SS handle 75 mm, CP Piano hinges, magnet/catcher (v)The quoted rates are included the rates of all fittings and fixturs

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ugs/SS dash fasteners of required dia including necessary hold fast/lugs or SS dash fastener complete as per direction of Engineer-in-Charge.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws,, 4x stainless steel hinges in each shutter 2x ss handle oval type magne/catcher all as per direction of Engineer-in-Charge.

S&F Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc., n exc 10 kg each brackets, conforming to Fe -290 Gde E-165 (Brackets over 10 kg each to be measured under ‘Structural Steel') complete all as specified and directed.

M&L for form work to soffits of suspended slabs such as roof slabs etc for rough finished concrete surface complete all as specified and directed.

M&L for form work to Sides for slabs and Sides of RCC/PCC bands in walls, horizontal or sloping and Similar work exc 10 cm but n exc 20 cm wide for fair finished concrete surface complete all as specified and directed.

Excavating in post holes in any type of soil n. exc. 0.50 cum getting out returning filling in and ramming earth or brocken rubble mixed with earth around, in layers not exceeding 25 cm watering, and removing surplus soil to a distance n. exc. 50 m and making good surface complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (40mm graded aggregate) as in post holes etc, any thickness size or shape complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, socket or power) complete (fittings such as switches, ceiling roses, pendants, regulatos, sockets etc to be measured separately), and making good disturbed surfaces of walls, floors etc to match with existing surfaces.

M&L for concealed Point wiring for One Light point controlled by one, one way switch with two single core PVC insulate, unsheathed multistranded copper conductor cable of size 2.5 sq.mm (FRLS) drawn in and including electrical grade PVC conduit 20 mm dia concealed on wall/ceiling/floor including PVC insulated unsheathed earth wire with multi stranded copper conductor of size 2.5 sq.mm (FRLS) including MS shunk sheet metal box with modular sheet top cover of required module or Bakelite sheet cover 3.0mm thick for mounting normal switches/sockets as per site requirement for mounting switches, sockets complete all as specified and as directed. Note : Quoted rates shall be deemed to include the cost of cutting chases in stone/brick wall as per site requirement for inserting the PVC conduit & cost of modular cover plate of required module Bakelite plate and making good to the disturbed surfaces including plastering and painting to match the existing colour.

All as per ser item No 134.00 but for One ceiling/exhaust fan point controlled by one switch and regulator

All as per ser item No 134.00 but for One 3 pin switch socket outlet, 5 Amp on the same board with other switches.

All as per ser item No 134.00 but for One 3 pin 5 amps switch socket outlet point on independent board.

All as per ser item No 134.00 but for One bell/buzzer point controlled by one bell push.

All as per ser item No 134.00 but for Two way point controlled by two way switch.

All as per item Sl. No. 134.00 here in before but wiring with 4 sq.mm multistranded cable and earth wire with copper conductor of size 4 sq.mm for 15 amps power point.

Supply and fixing Modular switch, one way 6 Amp, 1 module, piano type, 230/240 volts grade on top covers (catered in point wiring above).

All as per ser item No 141.00 but for Modular switch, two way 6 Amp, 1 module

All as per ser item No 141.00 but for Modular switch, one way 16 Amp, 1 module

All as per ser item No 141.00 but for Modular bell push 6 Amp, 1 module

Supply and fix Modular socket outlet 2 in1, 3 pin 5A, 2 module out let multipurpose use, flush mounting type, 230/240 Volts grade on Top covers (catered in point wiring above).

All as per ser item No 145.00 but for Modular socket outlet 2in1, 3 pin 15 Amps flush type

Supply and fix LED batten (1.2m) made of CRCA sheet housing with a PC glossy diffisure duly prewired connection having nominal system lumen output of 2000 lumens at a minimum system efficiency of 120 lumen per watt and total power consumption not more than 20 watt including driver. it should have rated system life time of 40000 burning hours at L70 and should have a temperature of 6500 K CRI >80, thd <10 and PF>0.95 complete all as specified and directed make - Crompton Cat Part CIS-305-40-57-HL2-DP-HWH, Philips Cat part BN308C LED20S-6500 L120 PSU WH, Havells Cat Part LHEBFOPN137W200.

Supply and fix lamp holder insulated body with back plate for angle/batten fitting with LED of 09 watt complete all as specified and as directed.

Supply and Fixing 20 watt emergency LED inverter bulb B-22 capacity with inbuilt powerful lithium battery backup of atleast 4 hours and having minimum two years warranty. The lighting shall have deep discharge protection, fast charging, offering cool day light for atleast four hours in off hours. Make : - Havells/Philips/Bajaj

Supply and fixing in replacement LED Bulkhead fitting 1 x 10 Watt, complete with Standard LED lighting fixture with extruded polycarbonate housing environment friendly, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to light fitting, complete fitting with all accessories and following specifications complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 5°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : <15%. (f) IP rating : IP-65. (g) CCT : Minimum 5400K (h) Polycarbonate housing white coloured (j) LED Driver of the same make as of the luminaire. (k) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (l) Surge protection minimum 2.5 kV. (m) CRI : Minimum 80 (n) Rated life time : 50000 burning hrs @L70 (Average 10 to 12 hrs daily)

Supply and fixing in replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-In-Charge

Supply and fix ceiling rose surface bakelite two to three terminals/plate 5 amps.

Supply and fix sheet metal enclosure DB single pole and neutral for 240 volts 8 way with 200 Amps rated busbar flush/surface mounting double door including wooden board.

Supply and fix Vertical MC DB distribution box 3 phase TPN 4 ways double door including MCCB 125 Amp 16 KA as incommer with bus bar rating 200 Amps vertical type dust and vermin proof complete all as specified and as directed.

Supply and fix MCB single pole 240 volt 6-32 amps 10 KA, complete all as specified and as directed.

Supply and fix MCB SPN 240 volt 32 amp 10KA complete all as specified and as directed.

S&F sub main wiring on and including passing through PVC conduit in concealed (including cutting chasis in stone/brick wall) 1100 Volts grade with PVC flexible cable copper conductor cable fire resistant low smoke and halogen (FRLSH) unsheathed multistranded single core of size 6 sqmm and continuous earth with PVC flexible cable copper conductor unsheathed multistranded single core of size 6 sqmm of green colour confirming to IS 694/1990 including taking down existing U/S sub main wiring. Note: (i) Two runs of cable with one run of earth wire and one run of PVC Coundit should measured as one length. (ii) The Quoted rates shall be deemed to include the cost of cutting chases in stone wall and brick wall as per site requirement and no extra payment shall be made on account of the same.

Earthing complete with galvanised steel earth plate electrode 600mmx600mmx6 mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level connected to GI wire 4mm dia by means of bolts, nuts, check nuts and washers complete including earthing pit, Chemical compound, GI wire 4mm dia up to 7.5 m, 20 mm dia medium grade GI watering pipe, G.I. protection pipe 40mm dia earth pit in PCC 1:2:4 type B-1 using 20 mm graded stone agggragate RCC pit cover including earth work complete all as shown electrical plate No-3 of SSR-2009 (Part-I) NOTE:- The unit rate shall include for excavation & earth work in any type of soil/strata, PCC 1:2:4 type B-I for pit & RCC 1:2:4 type B-I for cover with 8mm dia CTD Bar @150mm C/C both way, funnel with watering pipe 20 mm dia medium grade, 15mm dia light grade GI pipe up to 7.5 mtr long, wiremesh complete all as specified and directed.

S&F sheet metal incl single pole and neutral with 02 Pin and earth plug and socket complete with 01 single pole 20 Amps 240volts, MCB complete incl necessary fixing arrangement and all incoming and outgoing electric connection all as specified as directed by Engr-in-Charge.

S & F LED building security light fitting 35 watt with epoxy powder coated sheet aluminium housing, with epoxy powder coated CRCA sheet steel grey tray, clear acrylic cover and accessories complete incl street light bracket made out of 40 mm dia GI medium grade pipe 0.6 mtr long complete with 2 sets of FI clamps made out of 30x5 MS flat & nuts, bolts & washer including painting to clamp with two coats of aluminium silver paint over a coat of primer after taking down old u/s one.

Supply and fix fresh air fan 250 mm sweep 240 vot 50 Hz plastic body complete with louvers all as specified and direted by Engr-In-Charge

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 25 sqmm 4 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified & directed. Note : Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

Excavating in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes, laying of cables, pipes etc not exc 10 Sqm on plan and getting out in soft/loose soil.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified.

M/L for brick work with FLY ASH BRICKS(As Per IS-13757(1993) burnt clay fly ash building bricks), (OLD SIZE BRICKS) laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection and complete all as specified & directed.

M&L for dry sand and punning for cushioning to under ground cable all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

M/L for GI pipe ( Light grade ) for protection of LT cable fixed to walls/ poles/road crossing including clamps complete of 40 mm bore

Supply and fixing in repair of GI water tubing IS-1239 marked, medium grade, in replacement including all necessary pipe fittings laid in trenches, on wall, under floor, under road on same or new route and making good the disturbed portion as existing and including taking down of old unserviciable pipe of size 25 mm bore. Note :-Excavation and Earth work will be measured and paid separately

Supply and fixing switch piano, flush type, single pole, one way, 5/6 Amp, 230 Volts.

S&F switch piano flush type single pole two way 5 Amps 230 Volts .

S&F bell push flush type 5 Amps 240 V complete all as specified & directed.

S&F bell/buzzer AC 230 volts single pole complete all as specified & directed.

Supply and fixing switch piano, flush type, single pole, one way, 15 Amp, 230 Volts.

Supply and fixing socket outlet, 3 pin (with 2 pin outlet also), 5/6 Amp, flush type, 240 Volts.

Supply and fixing socket outlet, 2 in 1, 3 pin, 5 and 15 Amp, flush type, 240 Volts.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.

Supply and fix ceiling fan complete with electronic type regulator , copper winding and accessories 230v 1200mm sweep BEE 5 star rated with brushes direct current motor (BLDC) (35+10) including taking down old unserviceable ceiling fan and depositing the same to fan section of AGE E/M ALwar Sub Divn complete all as specified and directed by engineer-in-charge.

supply and fix exhaust fan metal body AC single phase 230/240 V of size 300 mm sweep with louver including making suitable opening/hole in wall all as specified and directed by ebgineer-in-charge

Radha Enterprises (BID ID -3361306)

shiva construction (BID ID -3361117)

M/S JINDAL ENTERPRISES (BID ID -3368760)