SPECIAL REPAIRS TO REAR SIDE GATE AND BOUNDRY WALL TO BLDG NO P01 AT SI LINES 10 SRW SPECIAL REPAIR TO SEPTIC TANK AT VIJAY ENCLAVE 11 SRW SPECIAL REPAIR TO SEWAGE LINE FOR HYGINE PURPOSE AT 68 ENGR REGT AND M W 07 AT BAIRAGARH UNDER GE BHOPAL

Amount

Note : Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below:-

M&L for Earth Work in excavation in any type of soil by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 m in width or 10 Sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m complete all as specified and directed.

M&L for Earth work in excavation in Ordinary rock by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exeeding 1.5 m in width or 10 Sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated material and disposal of surplus excavated material as directed, within a lead of 50m complete all as specified and directed.

M&L for Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F Mild steel TMT bars 6 to 8mm dia as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Use & waste of Form work to sides of concrete foundations, footings, bases of columns, sides & soffits of foundation and plinth beams and similar work for fair finished flat surfaces of concrete complete all as specified and directed.

Use & waste of Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick, for fair finished flat surfaces of concrete complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 in foundations, footing, plinth beams, bases for columns and mass concrete complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 in columns, pillars, posts & struts complete all as specified and directed.

M&L for Brick work with fly ash bricks (Modular), straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

M&L for raised pointing to random or polygonal rubble masonry, uncoursed or brought up to course in cement cement mortor 1:4 complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1: 6 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick each layer as in soil complete all as specified and as directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed. [MAKE: ACCOPROOF/WATER SEAL/MC BOUCHAMIE, MUMBAI/FOSROC/CICO/PIDILITE]

M&L for preparing new plastered or unplastered surfaces of walls and applying two coats of cement paint white or tinted complete all as specified and directed.

S&F Framed work of rolled mild steel conforming to Fe 410-W (Gde E-250) quality -A as in doors or gates of angle or other section with gusset plates, rails, braces, etc, drilled for fixing of steel sheeting or other covering; doors etc to be prepared for hanging or sliding with and including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting, running rails & guides) and hanging, fastening & fixing complete all as specified and directed.

M&L for mild steel, 0.63 mm thick plain black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required.

M&L for Preparing new or previously untreated steel & iron surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over & including a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for Providing precast reinforced cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate in louvers and jallies 25mm thick (measured solid) including all mouldings but excluding frame and set in cement mortar 1:4 complete all as specified and directed.

M&L for 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including grinding, moulding and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed trusses complete all as specified and directed.

Demolition of brickwork or stone masonry built in cement or cement lime mortar complete all as specified and directed.

M&L for 25-30cm thick Sand stone slabs in sunshades, coping, chajjas, shelves, cills, landings, cover stones, templates, etc, n exc. 1.2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:3 or cement mortar 1:4, complete all as specified and directed.

M&L for Providing cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate in cills, seismic and other similar bands, plinth courses, copings, bed plates, bond stones, etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

Demolition to cement concrete in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in any type of soil complete all as specified and directed.

All as per item No 28.00 above but exc 1.5 m deep but n. Exc 3 m deep complete all as specified and directed.

Excavation over area not exceeding 1.5m deep and getting out in any hard/ dense soil complete all as specified and directed.

All as per item No 30.00 above but exc 1.5 m deep but n. Exc 3 m deep complete all as specified and directed.

All as per item No 30.00 above but exc 3 m deep but n. Exc 4.5m deep complete all as specified and directed.

Demolition and breaking up drain pipes (SGSW, AC, RCC or PVC) set in cement mortar and disposal of unservicable materials and rubbish to a distance not exceeding 100m complete all as specified and directred.

M&L for Concrete bed to drain pipes of following bore including packing under and haunching against the sides of pipes after they are laid and tasted; in cement concrete 1:4:8 type D2 using 40mm graded stone aggregate complete all as specified and directed.

S&F Salt glazed stoneware drain pipes of following bore, grade ‘A’, laid in trenches and jointed as specified complete all as specified and directed.

S&F reinforced concrete pipes, class NP2, 200 mm bore, laid and jointed with collars complete all as specified and directed.

S&F reinforced concrete pipes, class NP2, 300 mm bore, laid and jointed with collars complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

M&L for Brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1: 4 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be mixed where directed by Engr in charge and WPC shall be measured and paid seperately

Supply only liquid integral water proofing chemicals complete all as specified and directed. [Make; Dr.Fixit Pidiproof LW+ of M/s Pidilite Industries or STP No. 1 (liquid) of M/s STP Ltd]

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 75 mm bore including taking down old pipe complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 110 mm bore including taking down old pipe complete all as specified and directed.

S&F PVC (SWR) bends any radius, 75 mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (single T), equal or unequal, 75mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (single T), equal or unequal, 110mm bore complete all as specified and directed.

Demolition of reinforced cement concrete in ground floors and pavings not exc 15 cm thickness (below or above ground level) (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 in screen wall, fins etc complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 in slabs supported on walls, beams & columns complete all as specified and directed.

M&L for Providing precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:4 complete all as specified and directed. (Note:-Reinforcement to be measured separately).

S&F Mild steel work conforming to Fe-290 Gde E-165 in bands, straps, supports or stays for rain water, including bolts, if required, hook and pintle hinges; handmade sliding bolts; clamps; hold fasts; hooks for hanging fans and similar small articles complete all as specified and directed.

S&F Mild steel conforming to Fe-290 Gde E-165 in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete all as specified and directed.

Supply and filling in soak well broken brick coarse aggregate (brick bats) of size .63mm complete all as specified and directed.

Use & waste of Form work to edges of concrete flats, openings, floors & roofs and sides of RCC/PCC bands in walls and similar work exceeding 10cm but not exceeding 20cm wide for fair finished surfaces of concrete complete all as specified and directed.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses etc; vertical or to batter

M&L for mild steel round bar 10 mm dia and over as in rungs for manholes, septic tank, steps etc complete all as specified and directed.

M&L for 25mm thick Cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate in sub base, complete all as specified and directed.

M&L for chequrred cement concrete tiles with grey cement and no pigments of size 200x200x25 mm thick, set in cement slurry laid jointed and pointed in neat cement slurry over and including bedding layer of 15 mm thick screed in CM 1:4 complete all as specified & directed.

Preparing new plastered or unplastered surfaces of wall and M&L for applying two coats of exterior acrylic emulsion paint, white or tinted over and including a coat of exterior wall primer on plastered surfaces complete all as specified and directed. [Make :Shalimar(Saktiman) / Asian(ACE) / Burger(wall masta)]

Preparing new plastered or unplastered surfaces of wall and M&L for applying two coats of distemper oil emulsion, white or tinted over a coat of primer and including 3mm thick wall care putty (Make: Birla/JK) on plastered surfaces complete all as specified and directed.

M&L for applying 3mm thick wall care putty (Make: Birla/JK) complete all as specified and directed.

M&L for Hard core of broken stone or boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, 75mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed.

S&F Steel water tubes, medium grade, ISI marked, galvanised, 15 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed. [MAKE: TATA/ SURYA/ JINDAL/ PRAKASH]

S&F Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size:- 914mm x 460mm x 203, bowl size:- 405mm x 354mm x 203mm, including CP waste coupling and 32mm dia PVC waste pipe of suitable length complete all as specified and directed. [MAKE:- Prayag (Cat No.1239D Gloss) or equivalent in NIRALI/BLUE STAR as approved by GE]

S&F Bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8606) or equivalent in JAGUAR/MARC as approved by GE]

S&F stainless steel kitchen plate rack overall size- 31" x 36" x 10" duly fixed on walls with gutties & screws of suitable length complete all as specified and directed. [MAKE:- Prayag (Cat No.P-340) or equivalent in NIRALI/BLUE STAR as approved by GE]

S&F in repairs Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (angle type) screwed both ends for iron pipe or for unions 15mm bore, complete all as specified and directed. [MAKE:- Prayag (Cat No.8610) or equivalent in JAGUAR/MARC as approved by GE]

S&F PVC (SWR) floor/Nahani trap, plain with CP grating including jointing with solvent cement, dia of outlet 75 mm complete all as specified and directed.

M&L for Cement concrete 1:2:4 type B2 using 40mm graded stone aggregate as in floors/ hard standing, etc, 75mm thick, laid in panels and finished even & smooth using extra cement complete all as specified and directed.

M&L for Factory made, machine pressed, M-35 grade concrete interlocking paver blocks (glossy /reflective type), with grey cement and pigment, any shape and size conforming to IS:15658-2006 (ISI Marked) of 60 mm thickness with & including 50 mm thick stone dust cushion and joints filled with sand complete all as specified and directed. [MAKE:- MEHTAB / NAVYA TILES / SAP PAVERS/ SAGAR TILES]

Excavating in post holes (or similar holes) in soft/loose soil each not exceeding 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and directed.

M&L for Cement concrete 1:2:4 type B-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

S&F Steel work in tubular/structural trusses, purlins, post etc including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 or steel sections conforming to Fe 410-W (Gde E-250) quality -A complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in roof coverings/cladding to wall, etc, fixed with & including self tapping screws on angle frame complete all as specified and directed. [MAKE: TATA BLUE SCOPE / EVEREST INDUSTRIES/JINDAL]

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in ridges, etc, fixed with & including self tapping screws complete all as specified and directed. [MAKE: TATA BLUE SCOPE / EVEREST INDUSTRIES/JINDAL]

S&F 50mm GI tubing light grade with all fittings as required for passing through cables under floors, along the wall or along the pole, etc with suitable size M.S.flat iron clamps incl nut,bolt and washer including taking down old rusted pipe complete all as specified and directed. [MAKE:-TATA / JINDAL / PRAKASH / SWASTIK as approved by GE]

S&F 40mm GI tubing light grade with all fittings as required for passing through cables under floors, along the wall or along the pole, etc with suitable size M.S.flat iron clamps incl nut,bolt and washer including taking down old rusted pipe complete all as specified and directed. [MAKE:-TATA / JINDAL / PRAKASH / SWASTIK as approved by GE]

Supply, laying, connecting and testing LT XLPE insulated, screened, PVC bedded, armoured, heavy duty cable with aluminium conductor of size 25 sqmm, 3.5 core, 1100 volts grade, laid in trenches, passing through pipes/ducts, etc including taking out old unserveciable cable, any type complete all as specified and directed. [MAKE:- POLYCAB /HAVELLS INDIA LTD/V-MARC as approved by GE]

M&L for sand filling with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection (8 cm below cable & 15 cm above cable) complete all as specified and directed. [Note:-Compacted/punned thickness shall be measured & paid]

Supplying and laying sub class 'B' bricks (modular) for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable complete all as specified and directed.

S&F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 200 amps rated busbar 16 KA, 4 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 including wooden rectangle board of first quality of suitable size for mounting of DB box including taking down old complete all as specified and directed. Make- Legrand/ Seimens/ Schinder/L&T.

S&F in repairs MCB SPN suitable for 240 volts, AC supply 6 to 32 Amps, with over load and short circuit protection and rupturing capacity not less than 10KA, complete all as specified and directed. [MAKE:Hegar (L&T)/ Siemens/ Legrand/HAVELLS as approved by GE]

S&F Post-top light fitting 35 W energy saving environement friendly, long life aesthetically disigned with symmetrical light distribution, spun aluminium landcape luminaire including lamps and pre-wired and including connecting up with copper conductor cable with suitable size complete all as specified and directed by Engineer-in-Charge (Make Havells Cat NO COPALPT 35 WLED 830PSYMTOPC/ Bajaj/Surya)

S&F PVC insulated unsheathed copper cable of size 2.5 Sqmm complete all as specified and directed by Engineer-in-Charge

Deduct schedule of credit (calculation will be done off line) Rs. 99852.50

M/S RAKESH TRADERS

anil kumar sahu

M/S AJAY JAIN

sabir and brothers