SPECIAL REPAIR FOR REPLACEMENT OF ASBESTOS SHEET TO PPGI SHEET IN BLDG NO N-95, N-96, N-108, N-153, N-157 AND N-158 OF DUNDAHERA STN GURUGRAM AND CERTAIN OTHER MINOR WORKS UNDER AGE B/R -II OF GE SOUTH DELHI CANTT-10.

Amount

Dismantling of asbestos cement (corrugated, semicorrugated, plain etc.) sheets as in roof coverings complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick having 150 GSM coating mass, any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with connected self tapping screws as specified complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick having 150 GSM coating mass, any colour having tensile strength of 550 Mpa as in ridge,roof covering/ cladding to wall, fixed with connected self tapping screws as specified as in roof coverings complete all as specified and as directed.

S&F mild steel work such as roof trusses (framed), trussed, purlins, and heavy bracket framing (Beam, Tee, angle, Channel or flat section) including distance pieces, cleat etc of Fe-290 (Gde E 165) including dismantling of wrought iron complete all as specified and directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed.

M&L for Brick work with sub class "B" bricks , straight or curved on plan exceeding 6 m mean radius built in cement mortar (1:6), (up to two story Bldg) including demolition of existing brick work of any descrition complete all as specified and directed.

M&L for 15 mm thick rendering with ready mix plaster on faces of brick or concrete surface, finished even and smooth without using extra cement complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B1 (20 mm graded stone aggregate) in roof kerb (gap between roof sheet and wall rounded or chamfered on edges complete all as specified and directed.

M&L for 15 mm thick rendering with ready mix plaster on faces of brick or concrete surface, finished even and smooth without using extra cement, including taking down cement plaster of any description complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying 1-2 mm thick cement base wall care putty on the surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified and directed. Note: (a) All works shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufacture shall have valid authorisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor

M&L for complete removal of existing treatment from external surfaces of walls by electrically operated grinder, washing and filling of holes with filler material and applying 1-2 mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm, complete all as specified and directed. Note: (a) All works shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufacture shall have valid authorisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor

M&L for preparation of newly plastered surfaces of walls and applying 1-2 mm thick cement base wall care putty on the surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of oil bound distemper over one coat of primer, complete all as specified and directed. Note: (a) All works shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufacture shall have valid authorisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor.

M&L for complete removal of existing treatment from internal surfaces of walls by electrically operated grinder, washing and filling of holes with filler material and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of oil bound distemper over one coat of primer, complete all as specified and directed. Note: (a) All works shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufacture shall have valid authorisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor.

S&F aluminium window as per TD drg No. CEDZ/TD-316 with following specifications :- (i) Outer frame of size 40mmx114mm with 1.3mm thickness, corner 45 degree cut & aluminium welded. (ii) Center mullion of size 40mmx65mm. (iii) Welded shutter (02 Nos) of size 40mmx60mmx1.3mm thickness 45 degree cut mechanically joint with 6mm allen key bolt clamp with 5 mm clear glass both side EPDM rubber gasket metal body hand lever type single point lock, aluminium kobra hinges 2 Nos per shutter. (iv) 12 mm SS 202 grade round bar safety grill at 100 mm cc distance modified to 150mm cc distance in front of handle, welded at both ends with 6 mm SS 202 grade round bar. (v) Welded wiremesh shutter (2 Nos) of size 40mmx18mmx1.3mm thickness 45 degree cut with 0.45 mm nominal dia of SS wire mesh, SS 75mm long hinges & PVC magnet. (vi) All aluminium sections shall be powder coated ( min 50 mm micron) with pure polyster coat of any shade as approved by GE. (vii) Window shall have provision for installation of window AC/Desert Cooler and provision of window glass shutter, wiremesh, grill and necessary fittings and locking arrangements for subject portion will be modified as per ground requirement during the execution as per directions of GE. (viii) Window shall be installed with silicone, complete all as specified and directed. (ix) Taking down of existing steel window.

S&F in repair PVC hollow false ceiling interlocking type 5-7mm thick plain/ coloured, fitted with MS hollow grid (light weight) section 25mmx25mmx1mm thick including fillets on joints, with hanging arrangements and including maintain levels with adjustable clips, complete all as specified complete all as specified and as directed. (Note:- If any minor electricial fittings and fixtures disturbed dueing execution of work shall be match and refixed as existing.)

Excavation in trenches not exceeding 1.5 m in depth and 1.5 m in width, not exceeding 10 Sqm on plan and getting out in soft/loose soil complete all as specified and as directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil complete all as specified and as directed.

Removing excavated material (soil) not exceeding 50 m and deposited where directed at a level not exceeding 1.5 m above the strating point complete all as specified and as directed.

M&L for cement concrete 1:4:8 type D2 (Using 40mm graded crushed stone aggregate) as in foundation, mass concrete and filiings complete all as specified and as directed.

M&L for form work to side of column and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels,slab and simillar work complete all as specified and as directed.

M&L for providing reinforcement cement concrete 1:2:4 (Nominal Mix) as in Beams, column, slab cantilevers, ressummers, lintels over 1.5m span concrete etc complete all as specified and as directed.

S&F mild steel TMT bars 10 mm dia and over, cut to length, bent to shape requred, including crancking, bending and binding with mild steel (annealed) wire not less than 0.90 mm dia complete all as specified and as directed.

All as per srl item No 22.00 here-in-before but 8 to 10 mm dia as in stirrups, spacers and binders.

M & L for brick work with sub class B old size burnt bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4 complete all as specifie and as directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and smooth without using extra cement complete all as specifie and as directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces with cement mortar 1:4 mixed with WPC finished even and smooth without using extra cement complete all as specifed and as directed. (Note : WPC will be measured & paid separately).

Supply only Liquid water proofing compound of approved quality.

M&L for preparation of new plastered surfaces apply two coat of cement based paint over a coat of primer complete all as specified and as directed.

M&L for preparation of the newly plastered surfaces of walls/ceiling applying wall care putty of 1 mm thick over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two or more coats distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specifie and as directed.

M&L for hardcore of gauge not exceeding 63 mm deposited, spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface for plinth protection/path complete all as specifie and as directed.

M&L for 75 mm thick cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base to floors finished even complete all as specified and as directed.

M&L for 25mm thick cement concrete 1:2:4 type B-1 (Using 20 mm graded crushed stone aggregate), as in sub base in floor/paving etc complete all as specified and as directed.

M&L for Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors etc laid on 15mm thick cement screed bed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade of tiles, complete all as specified and as directed.

M&L for coloured glazed ceramic tiles 300x450x6 to 7mm thick, in floors etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles including rendering 10 mm thick in cement mortar 1:4 complete all as specified and as directed.

M&L for 75 mm thick cement concrete type C-2, 1:3:6 (40 mm graded crushed stone aggregate) finishing cement concrete surface even and smooth without using extra cement as in plinth protection complete all as specified and as directed.

S&F urinal half stall type white with waste coupling and waste pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement , including urinal spreader of PTMT any colour for fixing with 15 mm dia pipe complete all as specified and as directed.

S & F Vitreous china squatting pan ‘Orissa’ pattern, size 580 x 440 mm, coloured, with integral foot rests, fixed in repairs including provision of lime concrete bedding complete.Squatting pan including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all as specified and as directed.

S&F low level flushing cistern of 10 ltrs capacity PVC valveless, syphonic action type, white with inlet ball valve float and handle complete all as specified as directed.

S&F CP brass health faucet with hand shower and 1.5 mtr flexible stainless steel pipe suitable for fixing to 15 mm dia pipe complete all as specified as directed.

S & F toilet paper holder of mild steel Chromium plated ‘D’ type, fixed in repairs to walls with chromium plated brass screws complete all as specified as directed.

S & F Vitreous china wash basin with pedestal white, flat back, size 550 x 400mm, including necessary waste pipe and coupling, brackets and cutting for and pinning in ends of brackets, complete all as specified as directed.

S&F elegent mirror PVC cabinet without towel rail of size 422 x 622 mm complete all as specified as directed.

S&F stainless steel foldable towel rack 60 cm long and 24 cm deep with towel rail and hangers at bottom fixed to walls complete all as specified as directed.

S&F brass chromium plated shower rose of size 125 mm with long arms including fixing to steel pipe complete all as specified as directed.

S&F 6 mm thick glass corner shelf fancy type with railing and fitting complete of size 25cm x 25 cm of best quality complete all as specified as directed.

S&F in repairs 15 mm bib tap, brass chromium plated fancy type (quarter turn), long body screwed down including necessary extention piece complete.

S&F 15 mm dia brass chromium plated angle valve fancy type (quarter turn), screwed at ends including necessary extention piece and fixed complete all as specified as directed.

S&F PVC connecton pipe 15 mm dia and 450/600mm long complete all as specified as directed.

S&F for rotational moulded polythylene water storage tanks 500 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified in SSR-I including brass valve high pressure with polythne float and fly nut , tank nipple as required complete, screwd for iron pipe or brass ferrule size 25 mm bore all as specified and as directed.

M &L for Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete including necessary filling of PCC in frame complete all as specified as directed.

S&F 35 mm thick Factory made 2nd class hardwood plain,framed paneled shutters(any numbe of panels) with lock rail and panel of 9mm BWP commercial ply with commercial veneering on both faces size of rail and stile as per IS-1003(part) Kiln seasoned and chemically pressure treated complete all as specified as directed.

S&F 35 mm thick factory made 2nd class Hard wood glazed and Skelton shutters (three panels) open rebated and prepared to receive and including wiremesh/glass/gauge etc with all accessory as required and divided into squares edges of framing Plain, chamfered or rounded mitered and rebated sash bar any number with cut or mitered beads for securing glass/gauge etc Size of members of shutters complete all as specified as directed.

M & L for preparation of new wooden surfaces of any description not otherwise described over 10 cms width or girth and apply two coats of synthetic enamel paint over a coat of pink primer complete all as specified as directed.

S&F Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285,fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings .

S&F fibre glass reinforced plastic (FRP) door frame, three lagged of cross section 90 mm x 45 mm having single rebatd of 32x15 mm to receive shutter of 30 mm thickness, moulded withfire retardant grade unsaturated polyesterresin and chopped mat. Door frame laminateshall be 2mm thick and shall be filled withsuitable wooden block in all over frame. The frameshall be covered with fibre glassfrom all sides including MS stay at the bottom to steady the frame complete all as specified and as directed.

S&F factory made solid FRP door shutter , 30 mm thick glass fibre reinforced plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire retardantgrade unsaturated polyester resin mouled to 3 mm thick FRP laminated for forming hollow rails and styles iwthwooden frame and suitable blocks of seasoned wood inside at required places forfixing of fittings, cast monolithically with 5 mm thick FRP panels and confirmign to IS 14856-2000 complete all as specified and as directed.

S&F stainless steel AISI 304 grade barrel tower bolt 200 mm long, extruded section, etc. complete all as specified and as directed.

S&F stainless steel AISI 304 grade handle of size 200mm long,etc. complete all as specified and as directed.

S&F Stainless steel of AISI 304 Grade, sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified as directed.

S & F Hasp and staple -100 mm size, safety type, aluminium anodised including bolt to hinge plate, fixed with screws complete all as specified as directed.

S & F Floor door stopper (double leg) of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 60 mm complete all as specified as directed.

M&L for 18 mm thick wood plastic composites (WPC) board, 100% solid with density not less than 650 Kg per cubic meter , one side wood grain finished laminated for exposed/external surface, fixed with screws fitted under or above the kitchen cooking platform and/or other platform including all necessary fittings and fixtures like nickle plated clip hinges, knobs, channels etc complete all as specified and directed. Note : (a) Pattern & design of WPC board to be decided by GE. (b) Items like cupboard knobs, stainless steel channel, CP plate clip hinges to be paid in extra.

S & F Continuous (piano) hinges width of flap 30 mm, mild steel, bright finish or electrogalvanised fixed to steel chowkhat with welding or with screws complete all as specified and as directed.

S&F stainless steel AISI 304 grade handle of size 75 mm long,etc. complete all as specified and as directed.

S&F magnetic catch for wooden cupbord with complete closer macanigum claps and clips fix with stainless steel screw.complete all as specified and as directed.

M & L for Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, welded or forged into spikes, framed guard bars, window frames, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work fixed in position including holdfasts or screws confirming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F 100 mm long medium weight cold rolled mild steel butt hinges complete all as specifed and as directed.

S&F extruded aluminium alloy handles, fabricated type anodised of 125 mm long complete all as specifed and as directed.

S&F Aluminium anodised barrel tower bolts of extruded section and fixed of 100mm long complete all as specifed and as directed.

S&F 250 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specifed and as directed.

M&L for Steel vantilator with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specifed and as directed.

M&L for 4.0 mm thick frosted sheet glass ordinary quality and glazing with oil putty in square n.exceeding 0.5 Sqm in each panes complete all as specifed and as directed.

S&F ball brass valve high pressure with polythene float and fly nut complete screwed for iron pipe of size 20mm dia complete all as specifed and as directed.

M&L 15mm GI tubing 'Medium grade' with all fiting and fixed complete tom wall and celing or laid in floor of fllowing sizes complete all as specifed and as directed.

All as per srl item No 76.00 here-in-before but 20 mm bore complete all as specifed and as directed.

S&F 100mm dia cast iron soil, waste and vent sand cast pipes in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specifed and as directed.

M&L for providing concrete bed to drain pipe including packing under and hauching against the sudes of pipes after they are laid and tested, in cement concrete 1:3:6 type C1 (Using 20mm graded stone aggregate) complete all as specifed and as directed.

M&Lfor salt-glazed stoneware gully traps, square or roun mouthed floor trap, plain with grating including jointing with solvent cement of 100mm dia complete all as specifed and as directed.

S&F CP grating of size 100mm dia complete all as specifed and directed complete all as specifed and as directed.

Excavation in post holes (or similar holes) each not exceeding 0.50 cum getting out returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25 cm watering and removing surplus soil n.exc 50m and making good the surface in any type of soil complete all as specifed and as directed.

M&L for mild steel work in tubuler trusses including special shaped washer, cleats etc complete using ERW or induction butt welded tubes confirming to IS: 1161-1979 grade st - 240 complete all as specified and as directed.

Surface dressing not exceeding 15 cm deep in any type of soil complete all as specified and as directed.

M&L for 100 mm thick Cement concrete 1:4:8 Type D-2, (40 mm graded crushed stone aggregate) , as in sub-base and similar works complete all as specified and as directed.

M&L for 60 mm thick machine pressed precast concrete interlocking paver block any colour, any shape and size confirming to IS 15658-2006, M-35 grade laid over and including 50 mm thick sand cushion complete all as specified & as directed.

Notes :- (i) The contract sum shall be after deducting the amount of Credit shown in Sch of Credit of this Tender. (ii) If any item of same description in nature is found to be entered as "double in BOQ" and the bidder quotes different rates against same item, then the rate quoted on lower side shall be applicable and higher rate will not be allowed to be paid in any circumstances. No claims on this account shall be entertained on a later date.

YP INFRA (BID ID -3343179)

Ex Serviceman Enterprises (BID ID -3342999)

M/S Malik Construction Corporation (BID ID -3351661)

Baljeet Builders & Interior Decorators (BID ID -3349445)

M/S MSD & Associate (BID ID -3349659)

M R INTERIOR HUB (BID ID -3341000)