Providing Lift irrigation Scheme for Horticulture Land from Pabber River to group of Villages in GP Karasa and Ukhli Mendhali Tehsil Rohru Distt Shimla HP

Amount

Excavation in earth work and disposal of all excavated earth upto a lead of 20 metres and lift upto 1.50 metres, disposed earth to be levelled and neatly dressed complete in all respect within all lead and lifts as per the direction of Engineer-in-Charge.

Providing and laying cement concrete 1:3:6(1cement:4sand:8graded stone aggregate of 40mm nominal size)and curing complete excluding cost of form work including all leads and lifts: a) Foundation and Plinth.

Providing & laying CC 1:1.5:3 1cement :1.5 damd 3 graded aggregates 20 mm nominal size curing completeexcluding cost of from work & reinforcement for RC C work in:-

Foundation footing and bases of columns & like mass concrete.

Columan pillar and post upto floor two level.

in suspending floor roofs landing shalves and thir support balconies beams grider bressumers cotilever upto floor two level.

wall any thicness

Stair cases (except spiral stair case) excluding landing i/c prepration of surface.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4mtrs.and removal of the same for in situ reinforced concrete and plain concrete work including all leads and lifts:

Foundation footing and bases of columns & like mass concrete.

Columan pillar and post upto floor two level.

Beam, contilever Girders and lintals side and soffits of beams haunching contilever girders not excluding 1mtr depth.

Vartical surface such as wall any thickness.

Flat surfaces such as soffits and suspended floos, roofs, landing and the like. as per direction & to the entire satisfaction of Engineer-in- Charge upto all lead & lifts.

Edge of slaband break in floor 20cm wide

Stair cases (except spiral stair case) excluding landing i/c prepration of surface.

Providing tor steel reinforcement for RCC work including bending, binding and placing in position i /c binding wire complete up to floor two level complete in all respectas per direction & to the entire satisfaction of Engineer-in- Charge upto all lead & lifts.

Half Brick masonary using common burnt clay building bricks above plinth upto floor two level in cm 1:4(1cement:4sand)conventiohal brick first class

Dry brick/boulder filling round sock pit 2nd class with in all leads and lifts as per direction of engineer in charge.

Providing wood work in frame of doors, windows, clearstorey window and other frames wrought, framed and fixd in position in 1st class deodar wood as per direction of Engineer in Charge.

Providing and fixing panneled glazed or panelled and glazed shutters for doors, windows and clerestory windows,including black enamelled iron butt hinges with necessary screws. 40 mm thick.1st class deodar wood. as per direction & satisfaction of the Engineer- in- charge upto all lead & lifts.

P/F wire gause shutters using MS wire gause of IS gause designation 85 G for doors windows clerestorey windows I/c bright finished black enamelled iron hinges with necessary secrews 30 mm thick 1st class deodar wood within all leads and lifts and as directed by the Engineer-in-charge.

Providing and placing horizontal layersfiltering media duly gradedscreened washed and cleaned as specified by the engineer in charge with in all leads and lifts.

Dry brick for filter bed/saptic tanks

coarse sand 3mm to 6mm

10mm thick cement plaster on fair side of brick/stone masonaryconvert wall for interior plastering up to floor two levelincluding arises internal rounded angles not exceeding 80mm girth in cm 1:3(1scement, 3 asnd) with in all leads and lifts.

15 mm thick cement plaster on fair sides of brick/stone masonery convrete walls for interior plastering upto floor two level including arises internal rounded angles not exceeding 80mm girth in cm 1:6 (1cement:6sand)within all leads and lifts and as directed by the Engineer-in-charge.

20 mm thick cement plaster on rough sides of brick/stone masonery convrete walls for interior plastering upto floor two level including arises internal rounded angles not exceeding 80mm girth in cm 1:6 (1cement:6sand)within all leads and lifts and as directed by the Engineer-in-charge.

6 mm thick cement plaster in cement concrete 1:3( 1cement 3 sand in roof slabs within all leads and lifts and as directed by the Engineer-in-charge.

Wall painting (two Coat) with plastic emulsion paint of approved brand and menufacture on undecorated wall surface to give and even shade including thoroughly brushing the surface free from mortar droping and other foreignmatter and sand paper smooth.

Finishing wall with water proofing cement paint of approved brand and manufacture and of rerquired shade on undecorated wall surfaces (two coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered

Providing and fixing 10mm thick antiskid water proof stain and impact resistant heavy duty verified tiles nitco or equlent 600x600mmx 10 menufectured and approved shade and colour in flooring and landing laid over( 12mm thick cement motor 1:3)(1 cement 3 sand) ointed with cement slurry mixed with pigment to match the shade of tiles as required complete within all lead and lifts and as directed by the Engineer in Charge.

Applying priming coat on new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil,greese,dirt and other foreign matters,sand papering and knotting.Ready mixed paint brushing wood primer pink. as per direction & satisfaction of the Engineer- in- charge upto all lead & lifts.

Painting two coats(excluding priming coat) on new wood and wood based surfaces with ready mixed paint brushing to give even shade including cleaning all dirt, dust and other foreign matters white paint.

Painting two coats(excluding priming coat) on new wood and wood based surfaces with ready mixed paint brushing to give even shade including cleaning all dirt, dust and other foreign matters white paint.

Providing and fixing of MS Grill of required pattern in wooden frame of window etc. With MS round headed bolts and nutsor by screw: Plain Grill.

Stone soling properly hand packed filling interstices with spalls and consolidating with power road roller to the required gradient and camber including spreading watering and rolling of binding materials moorum or earth etc. 100mm spread thickness (finished work including materials and labour) within all leads and lifts an da directed by the Engineer-in-charge.

Providing and fixing anodised aluminum sliding door bolts with bolts and nuts screws etc. complete and as per direction & satisfaction of the Engineer- in- charge upto all lead & lifts. 250x16 mm.

Providing and fixing anodised aluminium tower bolts ( barrel type) with screws etc. complete and as per direction & satisfaction of the Engineer- in- charge upto all lead & lifts

(ii) 100x10 mm

Providing ad fixing anodised aluminium handles with necessary screws etc. complete as per direction & satisfaction of the Engineer- in- charge upto all lead & lifts.

Providing 40x3 mm flat iron hold fast 40cm. Long including fixing to frame with 10mm dia metres bolts, nuts and wooden plug and embedding in cement concrete block 30x10x15cm. 1:3:6( 1cement:3sand:6 graded stone att. 20mm nominal size) within all leads and as directed by the Engineer-in-charge.

Steel work welded in built up sections,trusses & framed work i/c cutting,hoisting & fixing in position & applying a priming coat of red paint :- with in all leads and lifts as per the entire satisfaction & direction of the Engineer Incharge

Providing and fixing of finalax pipe 40mm dia under floor (For connection cables) including all req. fitting i.e elbows,sockey etc.

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge.

Providing and fixing ridges or hips 60 cm overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges.

Providing and fixing 19mm thick commercial board water proof shutter for cup board i/e fixing with nickel plated piano hinges with screw etc.

Providing and fixing 19mm thick commercial board water proof shelves /box for cup boards i/e fixing with butt jouintiong and nails and screw etc complete.

providing and fixing 1.00mm thick coloured or plane laminated sheet (sunmica) on board/ply wood sheet with approved adhesive and nail etc complete.

Providing and fixing square edged cover fillets (beading) 19mm x6mm section, i/ec mitring at junction with wood screw and nails complete firist class dewdar wood.

Providing and fixing brass curtain rail with rollers stop ends and brackets in pelmets instead of wooden curtain rod 25 mm dia and brackets at first class deodar wood (actullenght) of rails of be measured.

Providing and fixing brass handles anodized transparent or dyed to required colour and shade with necessary screws etc. complete with in all leads and lifts and as directed by the Engineer in charge. 100 mm dia

Providing and fixing bright finished brass ball catcher 10 mm dia

P/F 65x35 mm special quality bright finshed brass cup board locks or wardrobe locks with six levers i/c necessary screws etc.

Proviidng and fixing veneered decorative plywood lining with decorative surface on one face with butt jointing and nails (frame work and cover fillets to be measured and paid for separately) 4 mm thick ply-3ply.

Providing and laying heavy dty precast cement conrete inter locking precast cement conrete inter lockiing paver blocks vibro compacted upto M-50 grade i/c border or kurb block grey or coured over sub-base of concrete with 25 mm thick average thikness of cement mortar 1:4(1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete (Sub base concrete floor to be paid for 40 mm thick inter locking blocks .

Providing and fixing vitreous China wash down water colset ( European type.. W.C Pan) with integral 'P' or 'S' trap including jointing the soil pipe in cement mortar 1:1 (1Cement : Island ) Seat and over to be measured and paid for separately) : Angle Indian (Universal Closed) with in all leads and lifts as per the directions of the Engineer in charge.

Providing and fixing Stainless steel Kitchen sink with drain board with in all leads and lifts as per the directions of the Engineer in charge, 470× 420x 178MM .

Providing and fixing vireous china wash baisn with single hole for piller tap with C.I or M.S brackers painted white flat back 630mmx 450mm within all leads and lifts and as directed by the Engineer -in - charge, including cutting holes and making good the same but excluding fittings:- with in all leads and lifts as per the directions of the Engineer in charge.

Providing and fixing PIMT coloured/ white high density polyethylene/ poly propylene 10 liters cap. Full flush European standard control low level flushing cistern with fitting and within all leads and lifts as directed by the Engin.

P/F C.P brass for wash baisn or sink (i) 32mm dia with in all leads and lifts as per the directions of he Engineer in charge.

P/F C.P soap dish with C.P brass brackets fixed to woolen cleats with C.P brass screws with in all leads and lifts as per the directin of the Engineer in charge.

P/F C.P brass Bib tap with capstan head (15mm dia) with in all all leads and lifts and as directed by the Engineer-in- charge.

P/F brass full wheel valve with capstan head (15mm dia) within all leads and lifts and as directed by the Engineer-in-charge,

P/F C.P brass towell rail complete with C.P brass brackets fixed to wooden plugs with C.P brass 600mmx20mm with in all leads and lifts as per the directions of the Engineer in charge.

P/F 600mmx120mm glass shelf with C.P brass brackets and guard rail complete fixed to wooden plugs with C.P brasss screws with in alll leads and lifts as per the direction of te Engineer in charge .

Providing and fxing toilet paper holder: CP brass with in all leads and lifts as per direction of Engineer in charge.

Providing and fixing plastic storage tank 1000 lit. with in all lead and lifts as per direction of Engineer in charge.

P/F C.P Angle cock 15mm dia within all capstan head(15mm dia) within all leads and lifts as per the direction of the Engineer-in-charge,

Providing and fixing C.P Pillar tap with capstan head (15mm dia) within all leads and lifts as per the direction of the Engineer-in-charge,

Providing and fixing C.P stop clocks (15mm dia) with in all leads and lifts as per the directions of the Engineer in charge.

P/F of GI Elbow 15mm with in all leads and lifts as per the direction of the Engineer in charge.

P/F of GI Tee 15mm with in all leads and lifts as per the directions of the Engineer in charge.

P/F of GI Nipple 15mm with in all leads and lifts as per the direction of the Engineer in charge.

Laying galvanized mild steel tube (heavy class) in wall celling including with in all leads and lifts as per the directions of the Engineer in charge . 15mm dia (fifteen milimeters) nominal size. (H.C)

Providing and fixing 600mmx450mm bevelled edge miror of superior glass mounted on 6mm thick A.C sheet or plywood sheet and fixed to wooden plugs with C.P brass screws and washers. Within all leads and lifts and as directed by the Engineer-in-charge.

Providing and fixing C.I gratings (100X100)

Providing and fixing to wall celling and floor PVC pipe tube fitting and clamps including making good the wall,celling and floor:-

80mm dia

110mm dia

Providing and fixing PVC plane bend

80mm dia

100 mm dia

Providing and fixing PVC door bend

80mm dia

100 mm dia

Poviding & fixing PVC Tee

80mm dia

110mm dia

Providing and fixing PVC collor.

80mm dia

100mm dia

Poviding & fixing PVC Floor Trap

providing & fixing cowel.

110mm dia

80mm dia

Providing & fixing clamps

80mm dia

110mm dia

Wiring for light point/ fan /point/exhaust fan/bell point with 1.5 sq. mm PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC conduit conductor and earthing the light point with 1.5 sq. mm. HRFRLS/PVC insulated single core copper conductor cable as required . with in all leads and lifts as per direction of the Engineer-in-charge. Group (A)

Wiring for power plug with 2x4 sq.mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible ) copper conductor cable in PVC conduit along with 1 No. sq. mm HRFRLS/PVC insulated single core copper conductor cable conductor cable for earthing as required. with in all leads lifts as per direction of the Engineer-in-charge. Group(A).

Wiring for power plug with4x4 sq.mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible ) copper conductor cable in PVC conduit along with 2 No. 4 . sq. mm HRFRLS/PVC insulated single core copper conductor cable conductor cable for earthing as required. with in all leads lifts as per direction of the Engineer-in-charge. Group(A).

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke sinlge core ( (flexible) copper conductor cable in PVC Conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing . with in all leads and lefts as per direction of the Engineer-in-charge.

2x1.5 sq. mm.

2x10 sq.mm.

Supplying and fixing wooden boxes of following sizes (normal size) on surface or in reces suitable for fixing phenolic laminated sheet cover in front including painting etc. as required with in all lifts as per direction of the Engineer-in-charge.

102mm x 102mm.x 60mm. Deep.

203mm. X152mm.x 60mm. Deep.

Supplying and fixing following rating Piano- type switch/socket on the existing switch box/cover including connections etc. as required with in all leads and lifts as per direction of the Engineer-in-charge.

S.P 5/6 Amps one way switch, piano type.

S.P 15/16 Amps one way, switch porcelain base/paino type.

5 pn 5/6 Amps socket outlet, porcelain base/paino type.

6 pin 15/16 Amps socket outlet, porcelain base/ piano type.

Supplying and fixing bakelite batten/ angle holder including connection etc. as required . With in all leads and lifts as per direction of the Engineer-in-charge.

Supplying and errection of 6 amps, to 32 amps , rating , 10 KA breaking capacity, 240 volts, 'c' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connection etc. as required . With in all leads and lifts as per direction of the Engineer-in-charge. single pole. Cat-A.

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connection, testing and commissioning etc. as required, with in all leads and lifts as per direction of the Engineer-in-charge. 40 Amps. Cat-A.

Supplying anf fixing of following way, single pole and netural sheet steel MCB distribution board, 240 volts on surface/ recess, complete with tinned copper bus-bar, wire-set, netural link, earth bar, din-bar, detachable glad plate, blanking plate, cable identification lables inter-connection phosphatized and powder painted, including earthing etc. as required. with in all leads and lifts as per direction of the Engineer-in-charge. Single door-6 way.

Earthing with GI earth pipe 4.5 mtr. Long and 40mm dia, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete asa required, with in all leads lifts as per direction of the Engineer-in-charge.

Extra for using salt and charcoal for pipe earth eletrode complete as required, with in all leads and lifts as per direction of the Engineer-in-charge.

supplying and laying 6 SWG GI wire at 0.50 mtr. Below ground level for earth electrode conductor, including soldering etc. as required with in all leads and lifts as per direction of the Engineer-in-charge.

Providing and fixing seek and decorative strip type fixture domestic electronic ballast and colored engineering plastic end plates, suitable for 28 watt FTL (T5), complete with all accessories (excluding the T-8 tube), connection, testing and commissioning etc. as required 1x 28 watt- FTL (T5) (Category-A with in all leads and lifts as per direction of the Engineer-in-charge.

Providing , Installation , testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (upto 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixiing phenolic laminated sheet cover on the fan box and earthing etc. as required . with in all leads and lifts as per direction of the Engineer-in-charge. Ceiling Fan 1200 mm sweep Category-A

Providing, Installation , testing Exhaust fan of following size in the existing opening , i/c making the hole to suit the size of the above fan making good the damages connection testing and commisioning etc. as required Exhaust Fan light duty (Domestic) 225 mm sweep.

Supplying and fixing Ding-Dong/ Electronic musical bell, suitable for D.C/AC single phase, 230 volts complete as required, with in all leads and lifts as per direction of the Engineer-in-charge.

Providing and fixing of stationary storage type electric water heater (Geyser) of various sizes by means of expansion- bolt with nuts and washers. i/c embeldding of expansion - bolt in the wall , providing and fixing of non- return valve, Dead weight safety valve 2 No C.P. connection rods 18" long making good the damages, electrical connection, safrty valve connection, safety valve connection testing , testing and commissioning etc.as required 10 lters cap. water heater (Cat-A)

Supplying anfd fixing of stair way wall bracket contaaining LED lamp type holder of all size and shaves complete with all accessories complete with all accessories, connection, testing testing and commissioning complete as required, with in all leads and lifts as per direction of the Engineer-in-charge.

Yashwant Singh (BID ID -537512)

RAJNEESH THAKUR (BID ID -537488)