C O Divisional building Tissa at Bhanjraru in tehsil Churah Distt Chamba HP SH C o ground floor first floor electrical wiring water supply and sanitary fittings and breast wall

Amount

Excavation in foundation, trenches etc. in all kinds of soil such as pick work, jumper work, blasting work in soft / hard rock, chiselling in soft / hard including wedging out of a rock where blasting is prohibited and stacking the excavated earth up to all lifts, stacking the excavated soil up to all lead clear from the edge of excavation and then returning the stacked soil in 15 centimeters layers when required in to plinths, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as per direction and to the entire satisfation of Engineer- in- charge up to leads and lifts.

Providing form work with steel plates of 3.15mm thick, welded with angle iron in frames of 30x30x5mm so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling not exceeding 4mm and removal of the same for in-situ reinforced concrete and plain concrete work within all leads and lifts as per the direction of Engineer-in-Charge

Foundation footing and basis of columns, etc. and mass concrete.

In column pillar post and struts square rectangular or polygonal in plan.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like :-Floor etc. upto 200mm in thickness

Beams, cantilever, girders and lintels :- Sides and soffits of beams, beam haunching cantilevers, brssumers and lintels not exceeding 1 metre in depth in all heights from floor

In staircases

in vertical surface such as wall of (any thickness) but not less than 0.10 m including attached plasters buttresses, plinth and string course etc

Providing & laying cement concrete 1:4:8 (1 cement:4 sand:8 graded stone aggregate 40mm nominal size) & curing complete excluding cost of form work in Foundation & plinthwithin all leads and lifts as per the direction of Engineer-in-Charge

Providing and laying cement concrete work 1:1.5 :3 ( One cement : one and half sand : three graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in foundation and plinth with in all leads & lifts as per the direction of Engineer-in-Charge.

C/O dry Rubble masonary for R/Wall B/Wall & Parapet wall in all respect as per the direction of Engineer in charge within all leads and lifts as per the direction of Engineer-in-Charge

Stone soiling properly hand packed filling interstics with spalls and consolidating with power road roller to the required gradient and camber including spreading watering and rolling of binding materials moorum or earth work etc. ( 100mm th. Spread thickness (finished work including materials and labour )within all leads and lifts as per the direction of Engineer-in-Charge

Random rubble masonry/polygonal rubble masonry (uncoursed brought to courses) with hard stones of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (1cement :6 sand :12 graded stone aggregate 20 mm nominal size) at plinth level in CM 1:6 (1 Cement :6 Sand)within all leads and lifts as per the direction of Engineer-in-Charge

Providing and laying cement concrete work 1:1.5 :3 ( One cement : one and half sand : three graded stone 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work within all leads and lifts as per the direction of Engineer-in-Charge

Foundation footing and basis of columns, etc. and mass concrete.

In column pillar post and struts square rectangular or polygonal in plan.

In Suspended floor such as soffits of suspended floors, roofs, landings and the like :-Floor etc. upto 200mm in thickness

Beams, cantilever, girders and lintels :- Sides and soffits of beams, beam haunching cantilevers, brssumers and lintels not exceeding 1 metre in depth in all heights from floor

In staircases

Providing Tor steel reinforcement for reinforced Cement Concrete work including bending, binding and placing in position complete star wires complete its completion for all floors, within all leads and lifts of within all leads and lifts as per the direction of Engineer-in-Charge.

P/L mechanically mixed upto first floor level reinforced cement concrete 1:1.5 :3 ( One cement : one and half sand : three graded stone aggregate 20 mm nominal size) and curing complete including centering and shuttring etc. but excluding cost of reinforcement in moulding as in cornices window cill etc. exceedind 15 cm in girth upto floor all level within all leads and lifts as per the direction of Engineer-in-Charge

2nd class brick work using common burnt clay bricks in superstructure above plinth level upto floortwo level in cement mortar 1:6 (1 cement : 6 sand)

2nd class Half brick masonary using common burnt clay building bricks in superstructure in cement mortar 1:4 (1 cement : 4 sand) upto floor to level within all leads and lifts as per the direction of Engineer-in-Charge

Providing wood work in frames of doors, windows, clestorey window and their frames wrought framed and fixed in position first class Sal wood used within all leads and lifts as per the direction of Engineer-in-Charge

15mm th Plaster in two coats backing coat 10mmand finishing coat 5mm thick on fair side of brick masonry as well as rough side of brickmasonry /conc.upto floor two level including arises internal rounded angles chafter and /or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:4 within all leads and lifts as per the direction of Engineer-in-Charge

6 mm Cement plaster to ceiling in cement mortor 1:3 (one cement isto three sand) with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing & laying cement concrete 1:6:12 (1 cement:6 sand:12 graded stone aggregate 40mm nominal size) mechanically mixed & curing complete excluding cost of form work in Foundation & plinth within all leads and lifts as per the direction of Engineer-in-Charge

Filling in plinth with sand under floor including watering, ramming, consolidating and dressing complete within all leads, lifts of materials within all leads and lifts as per the direction of Engineer-in-Charge

Providing pre-cast terrazzo tile 20mm thick with marble chips of specified size laid in floor, treads of steps and landing in a bed of 20mm average thickness of cement mortar 1:6 (1cement: 6 and) jointed with neat cement slurry mixed with pigment to match shade of tiles (wherever required i/c rubbing and polishing complete with white tiles

White glazed tiles 6 mm thick in skirting risers of steps and dado 12 mm thick cement mortar 1:3 (one cement is to three sand) and finished with flush pointing in white cement with in all leads and lifts and as per the direction of the Engineer-in-charge

P/F Flush door shutters decorative type core of block board const. with frames of first class hard board and well matched first class indian teak wood ptyveering with vert. grains or cross bends and face veneering on both faces of shutter 35mm thick back enamelled MS butt hinges with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws.40 mm thick 2nd class Deodar wood with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing and fixing MS plain grills of required pattern in wooden frames of windows extra with M.S flats square round bars with round headed bolts and nuts plain grill with in all leads and lifts and as per the direction of the Engineer-in-charge.

P/F 12mm thick and 10mm wide pelmet with 25mm dia wooden curtain rod with hard bond with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing and fixing bright finished brass 100mm. Mortice latch with one dead bolt and a pair of levers with in all leads and lifts and as per the direction of the Engineer-in-charge

Bright finished M.S. hydraulic door closer with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing and fixing aluminium tower bolts (berrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete. 200x10mm with in all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Providing & Fixing MS iron Hinges 75x47x1.7 with in all leads and lifts and as per the direction of the Engineer-in-charge

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter sand papering and with readymixed paint brushing wood primer pink with in all leads and lifts and as per the direction of the Engineer-in-charge

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter, sand papering & stoping With enamel paint other than white with in all leads and lifts and as per the direction of the Engineer-in-charge

Applying Birla white/JK white wall care putty over plaster surface after thoroughly brushing the surface free from mortar dropping dust, loose materials and other foreign matter sand papered smooth to give final finish to the surface complete with in all leads and lifts and as per the direction of the Engineer-in-charge

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth with in all leads and lifts and as per the direction of the Engineer-in-charge

Finishing wall with water proof exterior grade emulsion of approved shade (Apexultima) or its equivalent on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete with in all leads and lifts and as per the direction of the Engineer-in-charge.

Providing and fixing in position collapsible steel shutters with vertical channels 20 mm X10 mmX2mm and braced with flat iron diagonals 20 mm X5 mm size with top and bottom rails of T.iron 40 mm X40X6 mm with 38 mm dia steel pulley complete with bolts and nuts locking arrangements, stoppers,handles,including applying a priming coat of red lead paint with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing and fixing moulded hand rail of M.S. hollow pipe 50mm dia welded in straight length over M.S. flat at top of vertical balusters including one coat of red oxide priming coat complete (M.S. flat & balusters of railings shall be mesaured & paid separetely with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing and fixing 2.5 mm thick M.S sheet garrage door with frame of 40 mmX 40mm X6mm angle iron 3.15 mm m.s gusset plates at the junctions and corners,all necessary fittings complete including applying a priming coat of red lead paint.Using M.S angles 40mm x 40mm x 6mm for diagonal braces with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing & Fixing cast iron Manhole cover with frame of internal dia 500mm (Medium duty) within all leads and lifts (weight of cover & frame should not be less than 116Kg) as per the direction of the Engineer-in-charge

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint In trusses and trussed purlins in buildings with in all leads and lifts and as per the direction of the Engineer-in-charge.

PROVIDING VALLEYS 90 cm.OVER ALL IN PLAIN WITH PREPAINTED PLAIN SHEETS FIXED J OR L HOOKS,BOLTS & NUTS 8 mm f GI LIMPET & BITUMENS WASHERS COMPLETE. (0.63 mm THICK PREPAINTED STEEL PLAIN SHEET) with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing and fixing flushing 38cm overall with 0.60mm thick prepainted sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia meter & prepainted G.I. limpet & bitumen washers complete with all accessories with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely) with in all leads and lifts and as per the direction of the Engineer-in-charge

Construction course rubble hammer dressed ‘U’ shape open surfaces drain with side wall 15x23cms (Fifteen into twenty three centimeters) in cement mortar 1:6 (one cement :six sand) and inside plastering with cement plaster 1:3(one cement :three sand) including earth work and laying 10cm (Ten centimeters) cement concrete in 1:5:10 (One cement: five sand: ten graded) crushed stone aggregate 40mm(Forty millimeters) nominal size and 7.5cm (Seven decimal five centimetres)cement concrete 1:2:4 (One cement: two sand: four graded) crushed stone aggregate 20mm(Twenty millimeters) nominal size and finished with a floating cost of neat cement complete as per standard design within all leads, lifts of materials with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing and fixing 40mm thick plain framed panelling with necessary screws priming coat on unexposed surfaces etc. complete with in all leads and lifts and as per the direction of the Engineer-in-charge

25 mm thick wooden flooring laid over R.C.C/C.C. (slab to be paid separately) thinly coated with thin layer of hot bitumen blown type @ 2.45 kg per sq m including fixing of wooden planks in position over wooden plugs fixed in Deodar wood second class with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete. 100 mm dia pipe with in all leads and lifts and as per the direction of the Engineer-in-charge

Recessed wiring for light / power plug with 2 x 2.5 sq.mm FR PVC insulated single core multistrand copper conductor of ISI marked with 20 mm dia non-metalic PVC flexible conduit alongwith 1 x 1.5 sq.mm FR PVC insulated single core multistrand copper conductor for loop earthing as required. ( Make of wire Finolex / L&T / Anchor / Havels / V Guard with in all leads and lifts and as per the direction of the Engineer-in-charge

Recessed wiring to light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor of ISI marked with 20 mm dia non-metalic PVC flexible conduit with 5 Amp, 250 V piano type switch ISI marked and ceiling rose ISI marked mounted on MS box having front Bakelite cover of suitable size , MS box with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire including all accesories and connection as per direction of Engineer in Charge. ( Make of wire Finolex / L&T / Anchor / Havels / V Guard ) with in all leads and lifts and as per the direction of the Engineer-in-charge

S.P.15 / 16 amps, one way modular switch, ISI marked

Supply and fixing of single pole MCB with sheet steel enclosure, distribution board, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, phosphate and powder painted including earthing etc. as required ( But with out MCB/ RCCB/ ISOLATOR) with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing Installation, Testing and Commissioning of resistance type ceiling fan regulator, in existing switch box including connection with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor,earthing the regulator as required with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing Installation, Testing and Commissioning of ceiling fan, in existingconnection with 1.5 sq.mm FR PVC insulated single core multistrand copper as required

Providing and fixing of lightning conductor finial made of 20 mm dia LED Tube 20 Walt base plate including holes etc.complete as required with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing and fixing of lightning conductor finial made of 20 mm dia LED Bulb 20 Walt base plate including holes etc.complete as required with in all leads and lifts and as per the direction of the Engineer-in-charge

Supplying and fixing batten holder / BK angle holder ISI marked including connection etc. as required with in all leads and lifts and as per the direction of the Engineer-in-charge

S.P.15 / 16 amps, one way modular switch with socket, ISI marked with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing and installation of gyser 15 ltr capacity , ISI marked with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing & Installation of Earthing with copper earth plate 600 mm x 600mm x 3.15 mm thick ISI marked including accessories and providing masonary with cover plate having loccking arrangement and watering pipe etc (But wih out charcoal and salt) as required with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing and laying in trenches galvanised mild steel tubes (medium grade) tube fittings (Earth work in trenches to be measured and paid for separately )15mm (fiften millimeter) nominal bore within all leads and lifts and as per the direction of the Engineer-in-charge

Providing and fitting vitreous china wash down water closet ( European type W.C. pan)with integral P or S trap including jointing the trap with soil pipe in cement mortar 1:1(one cemment isto one sand ).Seat and cover to be measured and paid for separently. ordinary closet as per the direction of the Engineer-in-charge including carriage of material within all leads and lifts

Providing and fixing 10/12.5/15 litres vitreous china low level flushing cistren with a pair of C.L. or mild steel)brackets compete with fittings such as lead valve less syphon 15mm (fifteen millimetre) nominal size brass ball valve with polythene float C.P brass handle unions and couplings for connection with inlet outlet and over flow pipes 40mm (forty millimeters dia C.P flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistren and closet (overflow pipe to be measured and paid for separately)as per the direction of the Engineer-in-charge including carriage of material with all leads and lifts

Providing and fixing plastic seat (solid/Hollow type )and cover for wash down water closet with C.P brass hinges and rubber buffes white plastic seat and cover as per the direction of the Engineer -in-charge including carriage of material within all leads and lifts

Providing and fixing vitreous china wash basin of Hindware with single hole for pillar tap with C.I or M.S. brackets painted white including cutting holes and making good the same but excluding fittings flat back 630mm X450mm (six hundred thirty millimeters into four hundred fifty millimetre) as per the direction of the Engineer-in-charge including carriage of material within all leads and lifts

Providing and fixing C.P brass waste of 32mm(thirty two millimetres) dia size for sink or wash basin. As per the direction of the Engineer-in-charge including carriage of materila within all leads and lifts

Providing and fixing 600mm X 450mm (six hundred millimetres into four hundred fifty millimetres) bevelled edge mirror of superior glass mounted on 6mm(six millimetre) thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brass screws and washers as per the direction of the Engineer-in-charge including carriage of material withon all leads and lifts

Providing and fixing 600mm X 120mm (six hundred millimetre into one hundred twenty millimetres )glass shelf with C.P brass bracket and guard rail complete fixed to wooden plugs with C.P brass screws as per the direction of the Engineer-in-charge including carriage of material within all leads and lifts

Providing and fixing 600mm X 20mm (six hundred millimetres into twenty millimetre) C.P. brass towel rail complete with C.P brass brackets fixed to wooden plugs with C.P brass screws as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts

Providing and fixing charomium plated brass soap dish with C.P brass brackets fixed to wooden cleats with C.P brass screws as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts

Providing and fixing C.P brass bib tap with capstan head 15mm (fifteen millimetre) dia with capaston head as per the direction of the Engineer-in-charge including carriage of material within all leads and lifts

Providing and fixing C.P brass pillar tap with capstan head 15mm (fifteen millimetre) dia as per the direction of the Engineer-in-charge including carriage of material within all leads and lifts

Providing and fixing C.P stop cock 15mm (fifteen millimetre) dia as per the direction of the Engineer-in-charge including carriage of material within all leads and lifts

Providing and fixing C.P brass angle valve 15mm (fifteen millimetre) dia as per the direction of the Engineer-in-charge including carriage of material within all leads and lifts

Providing and fixing brass full way valve with wheel 15mm (fifteen millimetre) nominal bore dia as per the direction of the Engineer-in-charge including carriage of material within all leads and lifts

Providing and supplying MS Sheet storage tank welded arround complete with 40 mm nominal bore galvanised mild steel over flow tubes with fitting and mosquito proof coupling of approved municipal design 15 mm nominal bore ball valve and mosquite proof galvanised mild steel cover with locking arrangement including providing pads of size as required for inlet and out let tubes and inside painting with a priming coat of red lead and three coats of bitumenous paint including housing up to a height of 10 mtrs above ground level as per direction of Engineer-in-charge 1000 lit net capacity storage tank of 2.00 mm thick M.S. Sheet

Providing and fixing cast iron floor trap of self cleaning design with sand cast iron screwed down or hinged grating with or without vest arm complete including cost of cutting and making good the walls and the floors with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing and fixing to wall, ceiling and floor 10.0 Kgf/cm² working pressure unplasticized P.V.C. Pipes (Confirming to IS: 4985-1968) complete with pipe fittings and clamps including making good the wall, ceiling and floor with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive class 6 kg /cm square

110mm (one hundred ten millimetre) dia as per the direction of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.

Providing and fixing to wall, ceiling and floor 10.0 Kgf/cm² working pressure unplasticized P.V.C. Pipes (Confirming to IS: 4985-1968) complete with pipefor weep hole with in all leads and lifts and as per the direction of the Engineer-in-charge

Providing & Laying cement concrete 1:5:10 (1Cement :5 Sand :10Agg STONE AGG. 40mm nominal size )WITH 15% plum and curring complete excluding the cost of form work in retaining wall / breast wall, the size of plum should usually 150mm to 300mm as per HPPWD specifications with in all leads and lifts and as per the direction of the Engineer-in-charge

Vinod Kumar

MS Kamal Dev Sharma