Loading
Loading…
Loading…
Tender Value
₹2.0 Cr
EMD Value
₹4.0 L
Closing Date
2 Sept 2026, 3:00 pm5d left
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
CIVIL MTN
14 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or V whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
(a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender. (b) (1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2)In such cases, what constitutes a component in a composite work shall be clearly pre-defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract.
Defination of Similar Work :- Any Civil Engineering works involving construction/modification/repair and maintenance of building/structure involving general construction activities viz concreting, masonry etc.
5 conditions
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The Contractor shall provide one Brand new All-in-One computer of Intel Core i3 processor with 8 GB RAM, of Asus, Acer, Dell, HP, HCL or Lenovo brand within two months from the date of issue of the Acceptance Letter.The All-in-One computer shall be used by RDSO for this contract-related works like agreement, billing, variations, addendums, corrigendum's etc. In case the Contractor fails to provide the computer within the stipulated period, a non-refundable penalty of 1,00,000/- (Rupees One Lakh only) shall be deducted from the Contractor's running bill.The Contractor shall maintain the computer at his own cost throughout the currency of contract and during maintenance period of the contract. The computer shall be used by the RDSO until completion of the maintenance period the contract. Upon completion of the maintenance period, the Contractor shall be entitled to take back the computer.No separate payment shall be made to the Contractor for providing or maintaining the computer during above mentioned period. While quoting the rates for the tender contractor has to keep this aspect into the consideration.
COMPLETION PERIOD The Contractors shall have to complete the work in all respects within a period of 10 (Ten) months including monsoon from the date issue of acceptance of the tender. The Contractor s will have to employ labour in full strength commensurate with working areas available. He will also arrange for materials and equipments to complete the job most expeditiously within the stipulated completion period. The Engineer s decision as to what is full strength will be final. He should also submit bar-chart for completing the work in time. The contractor/s will be required to maintain speedy and required progress to the satisfactions of the Engineer to ensure that the work will be completed in all respects within the stipulated period failing which action may be taken by the Railway Administration in terms of Clause 17 and/or clause 62 of the General Conditions of Contract, 2022. MAINTENANCE PERIOD The tenderer s shall be required to maintain the work effectively for a period of 12 (twelve) months from the date of completion as per Clause No.47 of the General Conditions of Contract 2022 and no part refund of Security Deposit shall be permitted during the maintenance period mentioned above.
Provision of the new water pipeline for the STP treated water provision in parks, bungalows/quarters lawn etc.
WKS-1477A-DC~RDSO
WKS-1477A-DC
Open
Works - General
10 Months
Lucknow, Uttar Pradesh
₹0
₹4.0 L
7 Aug 2026
7 Aug 2026
19 Aug 2026
62 items across 1 schedule · ₹2,70,25,628.82 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | DSR Item No 2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. | cum | 7000.00 | 218.6 | 15,30,200 |
| 2 | DSR Item No 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. | cum | 3500.00 | 161.6 | 5,65,600 |
| 3 | DSR Item No 4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 29.00 | 7,365.15 | 2,13,589.35 |
| 4 | DSR Item No 4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) | cum | 60.00 | 6,326 | 3,79,560 |
| 5 | DSR Item No. 6.1.2 Brick work with common burnt clay F.P.S. (non modular) bricks of classdesignation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 125.00 | 6,658.25 | 8,32,281.25 |
| 6 | DSR Item No 6.4.2 Brick work with common burnt clay F.P.S. (non modular) bricks of classdesignation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 67.00 | 8,288.4 | 5,55,322.8 |
| 7 | DSR Item No 10.1 Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Kg | 893.40 | 93.05 | 83,130.87 |
| 8 | DSR Item No 10.25.2 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works | Kg | 4200.00 | 142.3 | 5,97,660 |
| 9 | DSR Item No 13.4.2 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) | Sqm | 2000.00 | 294.35 | 5,88,700 |
| 10 | 13.18 Neat cement punning. | Sqm | 1200.00 | 67.8 | 81,360 |
| 11 | 15.2.1 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) | cum | 20.00 | 2,007.1 | 40,142 |
| 12 | DSR Item No 15.7.4 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar | cum | 25.00 | 1,698.45 | 42,461.25 |
| 13 | DSR Item No 15.60 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. | cum | 78.00 | 219.3 | 17,105.4 |
| 14 | 16.70.1 Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia 4 mm | Sqm | 350.00 | 859.5 | 3,00,825 |
| 15 | DSR Item No 16.91.2 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in- Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern | Sqm | 400.00 | 1,011.2 | 4,04,480 |
| 16 | 18.9.1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 15 mm nominal dia Pipes | Metre | 2000.00 | 221.35 | 4,42,700 |
| 17 | 18.9.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 20 mm nominal dia Pipes | Metre | 1000.00 | 275.25 | 2,75,250 |
| 18 | 18.9.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 25 mm nominal dia Pipes | Metre | 1800.00 | 370.65 | 6,67,170 |
| 19 | 18.9.4 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 32 mm nominal dia Pipes | Metre | 300.00 | 435.05 | 1,30,515 |
| 20 | 18.12.3 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 25 mm dia nominal bore | Metre | 500.00 | 417.95 | 2,08,975 |
| 21 | 18.12.5 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 40 mm dia nominal bore | Metre | 400.00 | 558.35 | 2,23,340 |
| 22 | 18.12.6 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 50 mm dia nominal bore | Metre | 600.00 | 654.2 | 3,92,520 |
| 23 | 18.12.8 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 80 mm dia nominal bore | Metre | 1050.00 | 919.1 | 9,65,055 |
| 24 | 18.13.1 Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore | Each | 50.00 | 757.1 | 37,855 |
| 25 | 18.13.2 Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 50 to 80 mm nominal bore | Each | 50.00 | 1,513.65 | 75,682.5 |
| 26 | 18.17.1 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore | Each | 50.00 | 532.35 | 26,617.5 |
| 27 | 18.17.3 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore | Each | 50.00 | 707.3 | 35,365 |
| 28 | 18.17.4 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore | Each | 50.00 | 878.25 | 43,912.5 |
| 29 | 18.26.1 Providing and laying flanged C.I. standard specials such as tees, bends, collars, tapers, caps etc., suitable for flanged jointing as per IS : 1538 : Up to 300 mm dia | Quintal | 70.00 | 8,191.75 | 5,73,422.5 |
| 30 | 18.27.1 Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 : 100 mm dia pipe | Metre | 3500.00 | 1,210.5 | 42,36,750 |
| 31 | 18.27.3 Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 : 150 mm dia pipe | Metre | 2400.00 | 1,824.7 | 43,79,280 |
| 32 | 18.28.1 Providing lead caulked joints to spun iron or C.I. pipes and specials, including testing of joints but excluding the cost of pig lead : 100 mm diameter pipe | Each | 600.00 | 410.25 | 2,46,150 |
| 33 | 18.28.3 Providing lead caulked joints to spun iron or C.I. pipes and specials, including testing of joints but excluding the cost of pig lead : 150 mm diameter pipe | Each | 400.00 | 615.75 | 2,46,300 |
| 34 | 18.29 Supplying pig lead at site of work | Quintal | 8.00 | 28,116.2 | 2,24,929.6 |
| 35 | 18.30.2 Providing flanged joints to double flanged C.I./ D.I. pipes and specials, including testing of joints : 100 mm diameter pipe | Each | 100.00 | 284.75 | 28,475 |
| 36 | 18.30.4 Providing flanged joints to double flanged C.I./ D.I. pipes and specials, including testing of joints : 150 mm diameter pipe | Each | 100.00 | 343.55 | 34,355 |
| 37 | 18.31.1.2 Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 100 mm diameter Class II | Each | 20.00 | 4,500.25 | 90,005 |
| 38 | 18.31.3.2 Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 150 mm diameter Class II | Each | 10.00 | 6,661.8 | 66,618 |
| 39 | 18.31.4.2 Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 200 mm diameter Class II | Each | 4.00 | 13,512.6 | 54,050.4 |
| 40 | 18.40.3 Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 25 mm diameter pipe | Metre | 500.00 | 15.25 | 7,625 |
| 41 | 18.40.5 Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 40 mm diameter pipe | Metre | 400.00 | 20.95 | 8,380 |
| 42 | 18.40.6 Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 50 mm diameter pipe | Metre | 600.00 | 25.25 | 15,150 |
| 43 | 18.40.8 Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 80 mm diameter pipe | Metre | 1050.00 | 36.4 | 38,220 |
| 44 | 18.41.3 Providing and filling sand of grading zone V or coarser grade, all round the G.I. pipes in external work: 25 mm diameter pipe | Metre | 500.00 | 164.1 | 82,050 |
| 45 | 18.41.5 Providing and filling sand of grading zone V or coarser grade, all round the G.I. pipes in external work : 40 mm diameter pipe | Metre | 400.00 | 170.5 | 68,200 |
| 46 | 18.41.6 Providing and filling sand of grading zone V or coarser grade, all round the G.I. pipes in external work : 50 mm diameter pipe | Metre | 600.00 | 176.9 | 1,06,140 |
| 47 | 18.41.8 Providing and filling sand of grading zone V or coarser grade, all round the G.I. pipes in external work : 80 mm diameter pipe | Metre | 1050.00 | 287.7 | 3,02,085 |
| 48 | 18.46.3 Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 25 mm nominal bore | Each | 10.00 | 369.35 | 3,693.5 |
| 49 | 18.46.5 Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 40 mm nominal bore | Each | 6.00 | 523.2 | 3,139.2 |
| 50 | 18.46.6 Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 50 mm nominal bore | Each | 4.00 | 706.7 | 2,826.8 |
| 51 | 18.46.8 Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 80 mm nominal bore | Each | 2.00 | 1,061.25 | 2,122.5 |
| 52 | 18.50.1 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore | Each | 20.00 | 715.05 | 14,301 |
| 53 | 18.52.1 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore | Each | 20.00 | 594.75 | 11,895 |
| 54 | 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore | Each | 22.00 | 500.35 | 11,007.7 |
| 55 | 18.54.1 Providing and fixing PTMT bib cock of approved quality and colour. 15mm nominal bore, 86 mm long, weighing not less than 88 gms | Each | 1000.00 | 109.85 | 1,09,850 |
| 56 | 18.55.1 Providing and fixing PTMT stop cock of approved quality and colour. 15 mm nominal bore, 86 mm long, weighing not less than 88 gms | Each | 1000.00 | 103.15 | 1,03,150 |
| 57 | 18.59.3 Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : 100 mm dia | Each | 5.00 | 8,214.1 | 41,070.5 |
| 58 | 18.68.1 Providing and laying D.I. specials of class K-12 suitable for push-on jointing as per IS : 9523 : Up to 600 mm dia | Quintal | 5.00 | 17,155.9 | 85,779.5 |
| 59 | 18.69.1 Providing and laying D.I. Specials of Class K - 12 suitable for mechanical jointing as per IS : 9523 : Up to 600 mm dia | Quintal | 5.00 | 18,025.6 | 90,128 |
| 60 | 18.71.1 Providing and laying Double Flanged (screwed / welded) Centrifugally (Spun) Cast Iron, Class B (IS : 1536) : 100 mm dia C.I. Double Flanged Pipe | Metre | 1000.00 | 1,838.1 | 18,38,100 |
| 61 | 18.71.2 Providing and laying Double Flanged (screwed / welded) Centrifugally (Spun) Cast Iron, Class B (IS : 1536) : 150 mm dia C.I. Double Flanged Pipe | Metre | 900.00 | 2,880 | 25,92,000 |
| 62 | 18.71.3 Providing and laying Double Flanged (screwed / welded) Centrifugally (Spun) Cast Iron, Class B (IS : 1536) : 200 mm dia C.I. Double Flanged Pipe | Metre | 342.00 | 4,535.1 | 15,51,004.2 |
| Schedule total | ₹2,70,25,628.82 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Tenderpdf1.pdf
ATTACHMENT
tenderpdf2.pdf
ATTACHMENT
tenderpdf3.pdf
ATTACHMENT
SpecialCondition.pdf
ATTACHMENT
tenderpdf4-compressed.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].