Repair/Replacement to Rolling shutter, cupboards, joinery, false ceiling, wall plastering in Tech area in BRD AF Station Chandigarh under GE (AF) MC Chandigarh

Amount

Taking down chowkhat or frame exc. 1.5 sqm but n.exc 4 sqm each without taking off shutter from the frame complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhat or frame n .exc. 1.5 sqm each without taking off shutter from the frame complete all as specified and directed by Engineer-in-Charge.

Taking down shutter of any description not exceeding 1 Sqm each complete all as specified and as directed by Engineer –In -Charge.

Taking down shutter of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and as directed by Engineer –In -Charge.

Dismantling structural steel work including doors, gates but excluding framed truss etc Complete all as specified and as directed by Engineer –In -Charge.

S&F for Pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, tarring back of chowkhats & holdfast etc., complete all as specified and directed by Engineer-in-Charge.

S&F for Pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, tarring back of chowkhats & holdfast etc, complete all as specified and directed by Engineer-in-Charge.

M&L for cement concrete 1:3:6 type C-0 as in pressed steel frames complete all as specified and directed by Engineer-in-Charge.

M&L for clean sawn second class hardwood in frame work complete all as specified and directed by Engineer-in-Charge.

S&F of factory made plain framed pannelled door shutters 35mm thick (two layer panel) with lock rail and panel of 9mm BWP commercial ply or 12mm verneering on both faces. The size of rail and stile as per IS-1003, SSR Pt-I kiln seasoned and chemically treated all as specified and as directed.

M&L for factory made flush shutters,35mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engineer-in-Charge.

M&L for 35mm thick factory made glazed and skeleton shutters,2nd class hardwood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); supplied and fitted to chowkats complete all as specified and directed by Engineer-in-Charge.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification complete all as specified and directed by Engineer-in-Charge.

S&F Factory made Solid PVC Moulded Door shutters with Particle board core 20mm to 30mm thick (stiles), with 2,4 or 6 raised panel design with 2mm thick moulded prelaminated PVC Sheet on front face & 2mm plain colour PVC sheet on back face, suppling & fixing in frame at site as per SSR specification complete all as specified and directed by Engineer-in-Charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification complete all as specified and directed by Engineer-in-Charge.

Taking down steel windows including guard bars and grills of any size complete all as specified and as directed by Engineer-in-Charge

Taking down cement plaster of any description on brick or stone walls, etc including racking out joints, hacking for key scrubbing down with water etc and removing the demolished material out side of the defence land complete all as specified and as directed by Engineer-in-Charge

M&L for aluminium composite panel sheet of colour/shade and pattern approved by GE of 4mm thickness which consists of 3 mm thick thermoplastic core of anti-toxic LDPE sandwiched between 2 skins of 0.5 mm thick aluminium foils with outer surfaces finished with 30 µ PVDF & inner surface finished with a thin coat of polyster paint, fixed in panels to aluminum frame including all necessary frame work or powder coated snap beading and rubber gasket complete all as specified and directed by Engineer – in - Charge. Make: Alstone/ Alex panel/ Armstrong/ Eurobond

M&L for Powder coated aluminum frame/shutter of any type for doors,windows,ventilators, partitions with one or more rebates including joining cleat etc fixed to frame with aluminium screws complete all as specified.

M&L for Powder coated aluminum frame /shutter of any type for sliding windows including joining cleat for fixing, screws, sliding rollers and suitable locking arrangement/clip lock complete all as specified.

S&F factory made box type steel window composite type with single rebate pressed steel frames 80mmx60mm (peripheral) and 80x75mm (intermediate members) made out of cold rolled 1.25mm thick sheet having steel window/ ventilator single shutters of MS tubular section of size 50mmx20mmx1.1mm thick fixed with box type hinges including 12mmx3mm MS flat as beading for wire and putty for glazing shutter, handle of 100mm size made out of Z section 01No., MS stove enamelled black tower bolt of size 120mm 02 Nos, 150mm mild steel hooks and eyes, each shutter flat iron 40mmx1.25mm and 200mm long holdfast 04 Nos each window inluding necessary filling frame with PCC 1:3:6 type C-0 , complete all as specified and directed by Engineer-in-Charge.

S&F factory made box type steel window composite type with double rebate pressed steel frames 80mmx60mm (peripheral) and 80x75mm (intermediate members) made out of cold rolled 1.25mm thick sheet having steel window/ ventilator double shutters of MS tubular section of size 50mmx20mmx1.1mm thick fixed with box type hinges including 12mmx3mm MS flat as beading for wire and putty for glazing shutter, handle of 100mm size made out of Z section 01No., MS stove enamelled black tower bolt of size 120mm 02 Nos, 150mm mild steel hooks and eyes, each shutter flat iron 40mmx1.25mm and 200mm long holdfast 04 Nos each window inluding necessary filling frame with PCC 1:3:6 type C-0 , complete all as specified and directed by Engineer-in-Charge.

S&F mild steel Mortice lock vertical type 100mm size, 6 lever fixed in aluminium shutter complete all as specified and directed by Engineer-in-Charge.

S&F in repair mild steel Mortice lock vertical type 100mm size, 6 lever fixed in aluminium shutter complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size,quality or description) from wooden/aluminium frames glazed with putty or fixed with beads.

S&F 5 mm thick float glass , Tinted/Smoked shade fixed to frame for door / window/ Partition etc including Aluminium powder coated snap beading and rubber gasket complete all as specified and directed by Engineer – in - Charge.

S&F 4.8mm thick plain glass exc 0.5 sqm in each pane fixed to aluminium door/ windows and iron frame including Aluminium powder coated snap beading and rubber gasket complete all as specified and directed by Engineer – in - Charge.

S&F 4mm thick plain glass n.exc 0.5 sqm in each pane fixed to aluminium door/ windows and iron frame including Aluminium powder coated snap beading and rubber gasket complete all as specified and directed by Engineer – in - Charge.

M&L for 3mm thick Sheet glass, ordinary quality and glazing with silicon sealant in square n exc 0.5 sq.m in each pane complete fixed in repair all as specified and directed by Engineer-in-Charge.

S&F Floor door stopper of aluminium alloy body and tongue, 140mm size ,anodised, with hard drawn steel spring complete all as specified and directed by Engineer-in-Charge.

S&F in repair Floor door stopper of aluminium alloy body and tongue, 140mm size ,anodised, with hard drawn steel spring complete all as specified and directed by Engineer-in-Charge.

S&F Door closer aluminium (Die cast) body, hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repair Door closer aluminium (Die cast) body hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 180 mm size Powder coated(any tint) aluminium "American Handle" fixed to aluminium door with suitable screws complete all as specified and directed by Engineer-in-Charge.

S&F in repair 180 mm size Powder coated(any tint) aluminium "American Handle" fixed to aluminium door with suitable screws complete all as specified and directed by Engineer-in-Charge.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed by Engineer-in-Charge.

S&F in repair Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed by Engineer-in-Charge.

S&F Mild steel Helical door spring including necessary welding where ever required complete all as specified and directed by Engineer-in-Charge.

S&F in repair Mild steel Helical door spring including necessary welding where ever required complete all as specified and directed by Engineer-in-Charge.

S&F aluminium powder coated grill (DECO grill) fixed to aluminium window / ventilator frame including all fixing arrangements including aluminium channels, screws, U or F section etc. , complete all as specified and as directed by Engineer –In -Charge.

M&L for two coats of synthetic enamel paint over a coat of pink primer including prepration to new wooden surfaces exc.10cm in width or girth complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of new or previously untreated steel surface of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

S&F 100mm size Butt hinges, medium weight, cold rolled mild steel bright finish complete all as specified and directed by Engineer-in-Charge.

S&F 100mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type C-21 complete all as specified and directed by Engineer-in-Charge.

S&F 100mm aluminium powder coated Butt hinges, galvanised mild steel hinge pin, complete all as specified and directed by Engineer-in-Charge.

S&F anodised Aluminium sliding door bolts 200mm,plate type, with bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed by Engineer-in-Charge.

S&F Aluminium handles, cast type, anodised 100mm in size fixed with screws complete all as specified and directed by Engineer-in-Charge.

S&F 200mm aluminium anodised tower bolts of extruded section fixed with screw, complete all as specified & directed by Engr-in-charge.

S&F in repair Powder coated Door Seal fixed with screws to any type of shutter complete all as specified and directed by Engineer-in-Charge.

M&L for cement concrete 1:2:4 type B-1 in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded for chamfered angles and throating, including provn of formwork complete all as specified and directed by Engineer-in-Charge.

M&L Rendering 15mm thick in cement mortar 1:4 on brick/concrete surfaces finishing even and smooth without using extra cement complete all as specified and as directed by Engineer –In -Charge.

M&L Rendering 15mm thick in cement mortar 1:6 on brick/concrete surfaces finishing even and smooth without using extra cement complete all as specified and as directed by Engineer –In -Charge.

M&L Two coats of Oil Bound Distemper over a coat of alkali resistant primer over new plastered surfaces including preparation of surfaces complete all as specified and as directed by Engineer –In -Charge.

M&L for two coats of cement base paint on walls including prepration to new plastered surfaces complete all as specified and directed by Engineer-in-Charge.

Repairing any type of aluminum door shutter and refixing it after resecuring its framework by means of tightening with new screws or by aluminium angle cleat and refixing it in the same opening complete all as specified and directed by Engineer-in-Charge.

Repairing any type of aluminum Window shutter and refixing it after resecuring its framework by means of tightening with new screws or by aluminium angle cleat and refixing it in the same opening complete all as specified and directed by Engineer-in-Charge.

S&F in repair the Pivot in aluminium door complete all as specified and directed by Engineer-in-Charge.

M&L mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed by Engineer-in-Charge.

M&L mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed by Engineer-in-Charge.

M&L for 5mm thick solid single side prelam (Texture to be approved by GE) PVC sheet and fixing at site on wall with solvents and headless nails etc, complete all as specified and directed by Engineer-in-Charge.

M&L for 5mm thick solid PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on wall by mean of solvent/nails/screws to make grid as per manufacturer instruction, complete all as specified and directed by Engineer-in-Charge.

M&L 12mm thick glass reinforced gypsum (GRG) ceiling tiles of size 595 x 595mm of approved design fixed with powder coated (powder coating on web bottom only) GI grid consisting of main Tee section of size (15mm x 30mm), cross Tee section of size (15mm x 23mm) and powder coated GI wall angle of size (20mm x 20mm) suitable for mounting tiles of 595 x 595mm with 4mm dia GI wire suspender including fabrication complete as per manufacturers instructions fixed with steel rawl plug with nut and bolts arrangement with grid size 60x120cm, in repair, complete all as specified and directed by Engineer - in -Charge. Make : Diamond Brand TM/ Dexune

S&F in repair powder coated GI grid consisting tee section of minimum size (24mm x 32mm) fixed in existing false ceiling height and including taking down existing complete all as specified and as directed by Engineer-in-Charge.

S&F in repair powder coated GI grid consisting wall angle of minimum size (20mm x 20mm) fixed in existing false ceiling height and including taking down existing complete all as specified and as directed by Engineer-in-Charge.

Fixing only powder coated GI grid consisting wall angle of minimum size (24mm x 32mm) fixed in existing false ceiling height and including taking down existing complete all as specified and as directed by Engineer-in-Charge.

Fixing only powder coated GI grid consisting wall angle of minimum size (20mm x 20mm) fixed in existing false ceiling height and including taking down existing complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 12mm thick glass reinforced gypsum (GRG) ceiling tiles of size 595 x 595mm of matching design fixed in existing frame height complete all as specified and as directed by Engineer-in-Charge. Make : Diamond Brand TM/ Dexune

S&F in repair 5 mm thick colour PVC sheet of any shade for false ceiling placed in snap grid of size 600mm x600mm including 12mm thick thermocal, pasted water based suitable adhesive fixed in existing false ceiling complete all as specified and as directed by Engineer-in-Charge.

Taking down steel/iron gates/collapsible gates area not exc 10 sqm including holdfasts and refixing the gates in the same opening including shifting and fixing of existing holdfast in plain cement concrete PCC 1:2:4 Type B-1 after raising the gate level/ repairing the same including greasing and other necessary minor repairs complete all as specified and as directed

Taking down steel/iron gates/collapsible gates area exc 10 sqm including holdfast and refixing the gates in the same opening including shifting and fixing of existing hold fasts in plain cement concrete PCC 1:2:4 Type B-1 after raising the gate level/ repairing the same including greasing and other necessary minor repairs complete all as specified and as directed

Dismantling mild steel rolling shutters, doors gates and the like complete all as specified and as directed by Engineer-in-Charge.

S&F 1.00mm thick steel rolling shutters without ball bearing of push pull or manual type as specified, including top cover, anchoring rod, hasp & staple and one shop coat of primer and two coats of synthetic enamel paint; erected in position as indicated complete all as specified and as directed by Engineer-in-Charge

S&F 1.25 mm thick steel rolling shutters without ball bearing or gear operated type with bevel gear box and crank handle as specified, including top cover, anchoring rod, hasp & staple and one shop coat of primer and two coats of synthetic enamel paint; erected in position as indicated complete all as specified and as directed by Engineer-in-Charge

Replacement of existing pulleys with new pulleys weight not less than 500 grams made of mild steel to the reqd shape and size incl necessary welding turning etc for smooth functioning to keep in position alignment complete.

Cleaning, oiling and greasing the guide channels of gear operated or manual type steel rolling shutter alongwith bevel gear box and crank handle complete all as specified

Replacement of existing unserviceable side lock arrangement of steel rolling shutter with new locking arrangement as per existing design, size and shape incl necessary rebating etc complete all as specified.

Overhauling, servicing and realignment of rolling shutters of area not exc 12 sqm including replacement of defective bearing and grinding of wheels for smooth movement of doors, replacement of clamps, bolts etc including cleaning, oiling and greasing of moveable parts and welding work complete all as specified and as directed.

Replacement of existing unserviceable mild steel wheel gear box with new wheel gear box of suitable for large size shutters having area more than 8 sqm incl its crank handle as per existing size and shape complete all as specified and as directed by Engineer-in-Charge.

Overhauling, servicing and realignment of rolling shutters of area exc 12 sqm but not exceeding 25 sqm including replacement of defective bearing and grinding of wheels for smooth movement of doors, replacement of clamps, bolts etc including cleaning, oiling and greasing of moveable parts and welding work complete all as specified and as directed. Note : - (i) Necessary arrangement of crane/moving ladder shall be made by the contractor with out any extra cost

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engineer - in -Charge.

M&L for brick work with sub class "B" bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer - in -Charge.

S&F in repairs steel window handles,left/right stove enamelled black nut bolt &washers complete all as specified and directed.

S&F in repairs peg stay exc 250 mm but n.exc 300mm long with 3/4 holes stove enamelled black suitable for existing steel window including nut bolts complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M & L Non-skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 20 mm thick screed bed CM 1:4. Make SOMANY/KAJARIA/ JOHNSON & JOHNSON.

M &L for Glazed ceramic coloured tiles in vertical surface 300x 600x 10 mm thick set and jointed in neat cement of required shape and size as in skirting/dado etc set and jointed in neat cement slurry over & incl 10 mm thick rendering in CM 1:4 and pointed in white or coloured cement to match including dismantling of existing tiles complete all as specified and as directed by Engineer-in-Charge. Make : SOMANY, Johnson & Johnson, Kajaria

MS SACHDEVA BUILDERS

M/s Bhagwati Enterprises

BAKSHI CONSTRUCTION CO.

N.N.CONSTRUCTION

Tejpal Singh and Co.

AMRIT SINGH

MS FUTEC ENGINEERS