PROVISION OF DEFI OFFICERS MD ACCN (PHASE ONE OF TWO PHASES) AT PUNE

Amount

SCH 'A' PART-I: BUILDING/STRUCTURES Note: This schedule is not pre-priced by MES and the rate indicated as "Rs 0.00" under Col 6 signifies this fact only

Construction of Block of Officers Married Accn consisting of 20 Qtr (Stilt floor + 5 floors) including Mumty complete all as shown in drawings and as specified. Notes: (i) One block consists of 04 qtrs in each floor (5 Storey) with sevant Qtr to each offr Qtr including stilt parking at GF level including Mumty. (ii) In Kitchen of Officers Qtr, cabinets above and below cooking platform and Working platform shall be of modular type and shall be measured and paid for saperately under respctive items of Sch 'A' Part XIV.

Construction of Block of Pump House with UG Sump complete all as shown in drawings and as specified.

Construction of Block of Sub Station building complete all as shown in drawings and as specified.

Construction of Garbage Bin complete all as shown in drawing No. CEPZ/97/TD/4 sheet 1/1 and as specified.

Construction of Septic tank for 400 users capacity complete all as shown on drawing No CEPZ/93/TD/12 STR sheet 1/1 and as specified.

Construction of Soakage well of size 3.60 m dia and 6.00 m deep all as shown in drawing No. CEPZ/2019/TD/03 sheet ½ & 2/2 and as specified.d.

NOTE: Schedule ‘A’ Part II to XIII items have been Prepriced by MES and the Bidders shall insert their lumpsum cost in green field under Column-6 only.

Total amount of Sch 'A' Part-II (Internal Water Supply)

Total amount of Sch 'A' Part-III (Internal Electric Supply)

Total amount of Sch 'A' Part-IV (Rain Water Harvesting)

Total amount of Sch 'A' Part-V (Road, Path and Culvert)

Total amount of Sch 'A' Part-VI (Area Drainage )

Total amount of Sch 'A' Part-VII (Sewage Disposal)

Total amount of Sch 'A' Part-VIII (Compound wall, Fencing and Gate)

Total amount of Sch 'A' Part-IX (External Water Supply)

Total amount of Sch 'A' Part-X (External Electric Supply)

Total amount of Sch 'A' Part-XI (Lightning protection)

Total amount of Sch 'A' Part-XII (Fire fighting system)

Total amount of Sch 'A' Part-XIII (Site Clearance, Excavation and Earthwork)

NOTE: Schedule ‘A’ Part II to XIII items which are not Prepriced by MES are given in Sch 'A' Part-XIV, Bidders shall insert their rate in Column-6 only and the Estimated rate indicated as "0.0" are for that purpose.

SCHEDULE 'A' PART-XIV (MISC B/R , E/M AND LIFT WORKS)

INTERNAL WATER SUPPLY

S&F Pillar cock with aerator 16 mm dia all as per Cera Cat No. Victor F1015101 or techno commercially equivalent model in makes as mentioned in Appendix 'C' complete all as specified and as directed by Engineer-in-Charge. NOTE :- Flow of the fixture must be 3.0 litre per minute or less.

S&F Bib cock with wall flange and aerator, 16 mm dia all as per Cera Cat No. Victor - F1015151 or techno commercially equivalent model in makes as mentioned in Appendix 'C' complete all as specified and as directed by Engineer-in-Charge. NOTE :- Flow of the fixture must be 3.0 litre per minute or less.

S&F Two way bib cock with side handle, wall flange and aerator 16 mm dia all as per Cera - Titanium Model No F1003161 or techno commercially equivalent model in makes as mentioned in Appendix 'C' complete all as specified and as directed by Engineer-in-Charge. NOTE :- Flow of the fixture must be 3.0 litre per minute or less.

S&F Hand shower (health faucet) with 1 meter long easy flex tube in chrome finish and wall hook with NRV (back flow preventer) all as per Cera Cat No. F8030104AB or techno commercially equivalent model in makes as mentioned in Appendix 'C' complete all as specified and directed by Engineer-in-Charge.

S&F Angular Stop cock 15 mm bore of pipe (16 mm outer dia) with wall flange, chromium plated stop valves all as per Cera Cat No. F8040204 or techno commercially equivalent model in makes as per Appendix 'C' all as specified and as directed by Engineer-in-Charge.

S&F Overhead rain shower square, with shower arm 180mm with wall flange, all as per Cera Cat No. F7010501AB and Cera Cat No. F7040101 or techno commercially equivalent model in makes as per Appendix 'C' all as specified and as directed by Engineer-in-Charge. NOTE :- Flow of the fixture must be 3.0 litre per minute or less.

S&F Wall mixer with bend pipe for overhead shower all as per Cera Cat No. F1015401 or techno commercially equivalent model in makes as per Appendix 'C' all as specified and as directed by Engineer-in-Charge. NOTE :- Flow of the fixture must be 3.0 litre per minute or less.

INTERNAL ELECTRIFICATION

S&F vertical triple pole and neutral DB, 6 way, double door, metallic modular distribution board for conforming to IEC 61439-3, suitable for flush / surface mounting with provision for MCCB up to 160 Amps as incomer and SP/TP MCBs as outgoing, fully insulated 200A copper busbar for each phase, two fully insulated & shrouded neutral bars, two earth bars, cable ties for cable management, prefitted masking sheet, etc. complete all as specified and as directed. NOTE:- MCCB & SP/TP MCBs shall be measured and paid separately.

S&F 125 Amps, 415 Volts, 25 KA, 50 Hz, Moulded case circuit breaker (MCCB), four pole, with thermal magnetic trip unit (TMD), compression lug connectors, protection against over loads (Ir adjustable from 0.7- 1 X In), protection against short circuits (Isd adjustable from 1.5- 10 X Ir),earth fault leakage protection, etc. having Ics = 100% Icu as per IEC 60947-2 complete all as specified and as directed.

Supply, installation, testing and commissioning of factory made, CPRI type tested, indoor cubical compartmental type Metering panel of suitable size, conforming to IEC 61439-1 & 2 and IEC 61641, having both sides openable with hinged single doors and locking arrangements, IP 43 protection, made out of 2.0 mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron of suitable size, including earthing stud, labelling, painting to all internal and external exposed steel surfaces with powder coating paint (7 tank process), duly fixed in ground with PCC foundation (1:2:4) type B1, with danger notice plate of 1.6 mm thick mild steel vitreous enamelled (white) with letters, figures and conventional skull and bones in signal red colour suitable for 3 phase, 4 wire system, 415 Volts with necessary wiring, PVC sheathed stranded copper conductor of appropriate length and size, including fixing lugs, bolts, screws, etc complete all as specified and directed. The metering panel shall comprise of the following:-

Busbar Chamber:- [i] 01 Set (3L+N) of Aluminium busbar of rated capacity 250 Amps, minimum current density 1.0 Amp / Sq.mm, covered with PVC insulated sleeves including insulator, nuts, bolts, etc. with complete connections. Incoming:- [i] 160 Amps, 415 V, Ics = 100%Icu, 25KA, conforming to IS/IEC 60947-2, 50 Hz, 4P MCCB with microprocessor based release, overload protection with inverse time delay, instantaneous protection with fine settings, protection against current unbalance and single phasing, inbuilt earth fault and neutral over load protection, compression lug connectors [ii] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interrupts- 01 Nos. [iii] LED phase indicators (Red, Yellow, Blue)- 01 Set. Outgoing:- [i] 32 Amps, 415 Volts, 10 KA, 50 Hz, FP MCB - 10 Nos. (for typical D.U) [ii] Space for three phase energy meter. - 10 Nos.( which is measured at relevant items of BoQ) [iii] LED phase indicators (Red, Yellow, Blue)- 10 Set. [iv] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interrupts-10 Nos.

S&F RF based smart three phase four wire energyy meter complete as all specified and as directed with the following specifications:- (i) Smart three phase four wire energy meter BIS 16444 2015 (Reaffirmed 2020) marked with transparent enclosure having current range 10-60A, 240V accuracy class 1.0, with inbuilt 865-867 MHz Radio frequency communication facility with self healing mesh network with default and on demand display, billing date generation facility, anti-tamper features, Microprocessor and LED, LCD based circuitry. (ii) Meter should support sending the following data to the software: 15/30 min instantaneous data for voltage, current, PF, power, cumulative energy and frequency, monthly billing survey for cumulative energy and max demand. (iii) Meter should have connect/ disconnect functionality operable from prepaid billing software. (iv) Meter should support open communication protocol DLMS with the software. MAKE: Secure, L&T, Schneider NOTE: The smart meter should be capable of running in both prepaid and postpaid mode and the meter should carry Five years warranty.

Supply and Installation IP-67 protection Data Concentrator Units (DCU) compatible for remote Automatic Metering Infrastructure (AMI) solution and capable of communicating with the smart energy meter in the corresponding frequency band and with the data server through GPRS/ Ethernet. It should have internal memory to store data of atleast 200 modules. It should have inbuilt battery backup, IP-67 protection. It should support auto discovery of the meters and self-healing mechanism for the breaks in the RF network. MAKE: L&T, Schneider, Cyan Connode

S&F 20 Watt, 230 Volts surface / wall mounted, 4 feet LED batten capable of delivering 2000 lumen, having PC diffuser, luminous efficacy of > 90 lumen/W, CRI > 80, PF > 0.9, CCT 6500K, polycarbonate diffuser, aluminium housing with integrated electronic driver, ABS end caps, IP 20 protection, input frequency 50 Hz, including electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and as directed.

S&F 10 Watt, 230 Volts surface / wall mounted, 2 feet LED batten capable of delivering 1000 lumen, having PC diffuser, luminous efficacy of > 90 lumen/W, CRI > 80, PF > 0.9, CCT 6500K, polycarbonate diffuser, aluminium housing with integrated electronic driver, ABS end caps, IP 20 protection, input frequency 50Hz, including electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and as directed.

S&F 7 Watt LED, 1 feet Mirror light suitable for wall mounting & 230 Volts, 50 Hz main voltage with built-in LED & driver, luminous efficacy of > 90, power rating ≤ 8 W, including IP 20 protection as well as electrical connection with 3 core 1.0 mm² PVC insulated copper conductor unarmoured cable to the fixture complete all as specified and as directed.

S&F 12 Watt, 230 Volts surface mounted round shape, LED down light with powder coated aluminium with integrated electronic driver capable of delivering 1200 lumen. having minimum luminous efficiency > 100 lumen/W, CCT 6500K, CRI > 80, high quality polycarbonate diffuser, input frequency 50- 60 Hz, including electrical connection complete all as specified and as directed.

S&F 10 Watt, 230 Volts surface mounted bulk head LED including inbuilt driver having minimum luminous efficiency > 100 lumen/W, CCT 6500K, CRI > 80, high quality polycarbonate diffuser, input frequency 50 Hz, including electrical connection complete all as specified and as directed.

S&F 25 Watt building security light having high efficiency long life LED module with SMD LED package mounted on MCPCB with high LED efficacy, having minimum luminous efficiency > 100 lumen/W, integral SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, IP 66 protection, high efficacy polycarbonate cover with integrated lens housed in pressure die-cast aluminium alloy heat sink for effective thermal management, sturdiness, excellent corrosion resistance, separate optical and control gear compartment & top opening for easy maintenance, suitable for side entry, pole mounting with bracket arm OD 35 mm to 42 mm including necessary electrical connection to the fixture with 3 core flexible copper conductor cable of appropriate size and 1.5 mtr long bracket, having 40 mm diameter light grade GI pipe, including GI clamps, nuts, bolts & washers with two coats of synthetic enamel paint over a coat of red oxide primer complete in all respects all as specified and as directed.

Supply and fix termination Geyser/AC box including 20 Amps, MCB 'C' curve 10KA with plug and socket complete all as specified and as directed.

S&F Modular type 1 module RJ 11 telephone socket with shutter complete all as specified and as directed.

S&F Modular type 1 module TV socket complete all as specified and as directed.

ROAD, PATH & CULVERT

M&L for preparing bituminous surfaces of road and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instructions complete all as specified and as directed.

EXTERNAL WATER SUPPLY

Provision for taking water supply connection from PMC with average capacity of 1 lacs LPD and testing, inspection of water meter, supervision and other miscelleneous charges of PMC, including excavation and earthwork, S&F required fittings like tee, flange, bend, jointing material etc complete all as specified and as directed.

Supply, laying, jointing and testing centrifugally cast ductile iron pipe class: K-7 with spigot and socket, suitable for push on rubber joint, with internal cement mortar lining and external metallic coating with finishing layer of black bituminous coating pipes in any length confirming to IS:8329-2000 including rubber gasket & joints laid in trenches / road / ducts / foot path/ on wall /on floor locations for 100mm dia pipe complete all as specified and as directed.

Supply, laying / jointing ductile iron fittings including rubber joint or gaskets (as per fitting requirement) such as bends (any type, radius and angle), heavy duty for spigot & socketed or flanged pipes, tapers any type, radius and angle like straight, bend, increasing, decreasing or double socket etc. Tee piece, single branch 'Y' junction double branch, collar etc. caps and plugs etc. with internal cement mortar lining and external zinc and black bitumen coated complete all as specified and as directed.

Supply, install, testing, commissioning and calibration of 100mm Analog water flow meter Class 'B' all as per manufacturer design and all as directed.

S&F CI swing type non return valve 65mm dia with flanged ends confirming to IS 5312, PN 1.6 with ISI marked complete with all necessary fittings such as nuts, bolts,washers, rubber gasket for both ends etc complete all as specified and as directed.

S&F CI foot valve with Nytrile rubber ball inside complete with flanged ends 80 mm dia confirming to IS 4038, ISI marked complete with all necessary fittings such as nuts, bolts, washers, rubber gasket etc complete all as specified and as directed.

M&L for Mono block pump set suitable for 415 Volts, 3 phase, 50 Hz, two pole, suction x delivery= 80mm x 65mm for the rating 10 HP complete including channels, foundation with PCC (1:2:4) all as per manufacturers instructions complete all as specified and as directed.

M & L for brick masonry valve chamber of size 1.20m × 1.20m x 1.20m (internal dimension) with 15cm thick foundation using PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) over 15cm thick hardcore, 23cm thick brick wall built in cement and sand mortar (1:4), 10mm thick internal and external plaster including top of floor in cement and sand mortar 1:3 finished even and smooth, without using extra cement, 10mm thick MS sheet cover with, 50mm x 50mm x 6mm MS angle frame embedded in PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) coping having rectangular hinged opening of size with locking arrangements & handle made out of 25cm dia MS round bar, hold fasts etc applying one coat of red oxide primer and two coats of synthetic enamel paint to all steel surface including excavation, refilling and earth work in any type of soil and disposal of surplus soil to a distance n.exc 50m complete all as specified.

EXTERNAL ELECTRIFICATION

M&L Providing Pre cast RCC 1:11/2:3 type A1 using 20 mm graded stone aggregates as in Cable Route Indicator of height 800 mm x width 300 mm x thickness 120 mm duly reinforced all as per details shown in drawing and having top circular section, provided with and including PCC 1:4:8 type D2 using 40 mm graded stone aggregates foundation of suitable size as directed and including engraving letters "MES 11 KV HT" on route indicator duly painted in synthetic enamel paint, complete all as shown in drawing No. CEPZ/2023/TD/01 sheet 1/1 and as specified and directed.

Supply, laying, testing and commissionnig of LT cable of size, 300 sq,mm 1 core, 1100 volts grade, XLPE insulated, PVC inner sheathed, unarmoured, including necessary clamping / dressing with cable ties and termination complete all as specified and as directed.(Transformer to LT Panel)

Outgoing:- [i] 250 A, 415 V, Ics = Icu = 50 kA, 50 Hz, 4P MCCB with microprocessor based release, overload protection with inverse time delay, instantaneous protection with fine settings, protection against current unbalance and single phasing, inbuilt earth fault and neutral overload protection, compression lug connectors - 03 No [ii] 400 A, 415 V, Ics = Icu = 50 kA, 50 Hz, 4P MCCB with microprocessor based release, overload protection with inverse time delay, instantaneous protection with fine settings, protection against current unbalance and single phasing, inbuilt earth fault and neutral overload protection, compression lug connectors - 01 No. [iii] LED phase indicators (Red, Yellow, Blue)- 4 Set [iv] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interrupts-4 Nos.

Supply, installation, testing and commissioning of factory made, CPRI type tested, indoor cubical compartmental type of suitable size, conforming to IEC 61439-1 & 2 and IEC 61641, having both sides openable with hinged single doors and locking arrangement, IP 43 protection made out of 2.0 mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron of suitable size, including earthing stud, labelling, painting to all internal & external exposed steel surfaces with powder coating paint (7 tank process), duly fixed in ground with PCC foundation (1:2:4) type B1, with danger notice plate of 1.6 mm thick mild steel vitreous enamelled (white) with letters, figures and conventional skull and bones in signal red colour suitable for 3- Phase, 4 Wire system, 500 V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length and size, including fixing lugs, bolts, screws, etc. complete all as specified and as directed. MAKE :- Schneider, ABB, Siemens, L & T The ESSENTIAL LOAD PANEL shall comprise of the following :- Busbar Chamber :- [i] 01 Set (3L + N) of copper busbar of rated capacity 400 Amps, minimum current density 1.3 Amp /sq.mm, covered with PVC insulated sleeves( colour code) including insulator, nuts, bolts, etc. with complete connection Incoming :- [i] 250 Amps, 415 Volts, Ics = Icu = 50 kA, 50 Hz, 4P MCCB with microprocessor based release, overload protection with inverse time delay, instantaneous protection with fine settings, protection against current unbalance and single phasing, inbuilt earth fault and neutral overload protection, compression lug connectors - 01 Nos.

[ii] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interrupts- 01 Nos. [iii] LED phase indicators (Red, Yellow, Blue)- 01 Set Outgoing :- [i] 160 Amps, 415 Volts, Ics = Icu = 25 kA, 50 Hz, 4P MCCB with microprocessor based release, overload protection with inverse time delay, instantaneous protection with fine settings, protection against current unbalance and single phasing, inbuilt earth fault and neutral overload protection, compression lug connectors - 02 Nos. (for Officer's Building Utility Panel & Spare) [ii] 63 Amps, 415 V, Ics = Icu = 25 kA, 50 Hz, 4P MCCB with microprocessor based release, overload protection with inverse time delay, instantaneous protection with fine settings, protection against current unbalance and single phasing, inbuilt earth fault and neutral overload protection, compression lug connectors - 01 Nos. (for water supply DBs) [iii] 32 Amps, 230, 10 KA, 50 Hz, FP MCB - 3 Nos. (for Substation DBs, street light panel) [iv] LED phase indicators (Red, Yellow, Blue)- 4 Set [v] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interrupts-4 Nos.

Supply, installation, testing and commissioning of factory made, CPRI type tested, indoor cubical compartmental type of suitable size, conforming to IEC 61439-1 & 2 and IEC 61641, having both sides openable with hinged single doors and locking arrangement, IP-43 protection made out of 2.0 mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron of suitable size, including earthing stud, labelling, painting to all internal & external exposed steel surfaces with powder coating paint (7 tank process), duly fixed in ground with PCC foundation (1:2:4) type B1, with danger notice plate of 1.6 mm thick mild steel vitreous enamelled (white) with letters, figures and conventional skull and bones in signal red colour suitable for 3- Phase, 4 wire system, 500 Volts grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length and size, including fixing lugs, bolts, screws, etc. complete all as specified and as directed. MAKE :- Schneider, ABB, Siemens, L & T The OFFICER BUILDING PANEL shall comprise of the following :- [i] 01 Set (3L + N) of copper busbar of rated capacity 400 Amps, minimum current density 1.3 Amp / sq.mm, covered with PVC insulated sleeves (colour code) including insulator, nuts, bolts, etc. with complete connection

Incoming:- [i] 250 Amps, 415 V, Ics = Icu = 50 kA, conforming to IS/IEC 60947-2, 50 Hz, 4 Pole MCCB with microprocessor based release, overload protection with inverse time delay, instantaneous protection with fine settings, protection against current unbalance and single phasing, inbuilt earth fault and neutral overload protection, compression lug connectors - 01 Nos. [ii] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interrupts- 01 Nos. [iii] LED phase indicators (Red, Yellow, Blue)- 01 Set Outgoing:- [i] 160 Amps, 415 V, Ics = Icu = 25 kA, conforming to IS/IEC 60947-2, 50Hz, 4 Pole MCCB with microprocessor based release, overload protection with inverse time delay, instantaneous protection with fine settings, protection against current unbalance and single phasing, inbuilt earth fault and neutral overload protection, compression lug connectors - 03 Nos. (for metering panel 1&2-02 Nos. & spare-01 Nos.) [ii] LED phase indicators (Red, Yellow, Blue)- 03 Set [iii] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interrupts- 03 Nos.

S&F 45 Watt street light having high efficiency long life LED module with SMD LED package mounted on MCPCB with high LED efficacy of ≥ 4200 lumen, integral SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection, IP 66 protection, high efficacy polycarbonate cover with integrated lens housed in pressure die-cast aluminium alloy heat sink for effective thermal management, sturdiness, excellent corrosion resistance, separate optical and control gear compartment & top opening for easy maintenance, including necessary electrical connection to the fixture with 3 core flexible copper conductor cable of appropriate size and 1.5 m long bracket, having 40 mm diameter light grade GI pipe, including GI clamps, nuts, bolts & washers with two coats of synthetic enamel paint over a coat of red oxide primer complete in all respects all as specified and as directed.

M&L GI Octagonal poles complete with single arm bracket all as specified for 9 mtrs long with 70 mm top dia and 130 mm bottom dia, made of 3 mm thick tensile sheet along with base plate of size 225x225 x12 mm thick including 04 Nos of M24 x750 long J type foundation bolts including 6 Amps MCB with 4 way heavy duty connector capable for 32A, including PVC three core wire 1.5 sq.mm from MCB to light complete including foundation/ RCC of pole excavation and earth work complete all as specified by the pole manufacturer (OEM) and as directed.

Supply, installation, testing and commissioning of intelligent street light control (ATSC) suitable for 6 KW maximum load, wall / pole mounted, having built-in networking support, built-in astronomical timer, 32 Amps, TP contactor, 40 Amps TPN MCB housed in 3.15 mm thick powder coated CRCA sheet housing complete including its wiring and accessories all as specified and as directed.

S&F LED post top lantern light fitting made of die cast aluminium housing with decorative opal acrylic diffuser with IP-65 protection including LED of capacity 25W complete with all accessories fixed on GI pipe 40/50 mm dia complete (for Gate lights) all as specified and directed.

S&F all in one smart integrated solar street light 40 watt with built in Mono Crystalline Solar PV Module Panel, Lithium Ferro phosphate battery, MPPT charge controller, PIP sensor, light having colour temp 6000-6500K, Lumens 4800, 2 days autonomy with dimming profile, including supply and erection of standard tubular pole of 6 m height having base plate of dimensions min 200 × 200 x 12mm, bolt size 4 Nos × 20 mm dia all including necessary brackets, excavation, earthwork, foundation, PCC and foundation bolts (Hold fasts) as per manufacture's design and specifications complete. Make - Havells Cat No SOLAR AIO 40 W or BAJAJ Cat No BSZSL 40W or equivalent make as per Appendix 'C'.

S&F aviation light on suitable appropriate fixture/pipe as per manufacturer specification of length 0.5m welded with base plate and fixing firmly on PCC block / floor as per site requirement complete all as specified and directed.

FIRE FIGHTING SYSTEM

M&L for FRLSH flame retardant fire alarm cable of size 2 core, 1.5 mm² conforming to BS 7629-1, BS 6387 & BS EN 50200 and rated for 500 Volts, having plain annealed stranded copper conductor with primary insulation of glass mica fire resistant tape and secondary insulation of high performance silicone rubber, earth / drain wire of annealed tinned copper, electrostatic screen of aluminium fire barrier and type LTS3 outer sheath conforming to BS 7655, suitable for operating temperature range -30 ˚C to +70 ˚C and minimum bending radius being 6 times the overall cable diameter, RED in colour, including laying, termination and ferruling complete all as specified and as directed. MAKE :- RR Kabel, Polycab, Havells

M&L for transparent FR PVC insulated, twin core copper conductor flexible industrial speaker cable having stranded annealed tinned copper conductor, PVC insulated cores twisted to form pairs, shielded for interference rejection, unarmoured PVC sheathed 1.1 KV grade in conductor size of 2 x 1.0 mm2 including laying, termination and ferruling complete all as specified and as directed. MAKE :- RR Kabel, Polycab, Havells

Supply, installation, testing and commissioning of UL listed (fire fighter's) addressable Telephone Jack mounted to a single-gang electrical back box with suitable interface module for two way communication with the Central Fire Fighter Telephone Console complete all as specified and as directed. MAKE :- Notifier FPJ + FCM-1 or equivalent model of JC, Esser

Supply, installation, testing and commissioning of UL listed Fire Fighter's Telephone Handset for two way communication with the Central Fire Fighter Telephone Console complete all as specified and as directed. MAKE :- Notifier FHS or equivalent model of JC, Esser

Supply, installation, testing and commissioning of UL listed all purpose 2 Watt ceiling speaker having crush and rust resistant design and fully ABS plastic & ABS grille with tap-setting range between 1/4 W and 2 W, rated (RMS) voltage 70.7 V, sound pressure level at 1 W (1 m & 1 kHz) 80 ± 4 dB, frequency response 125 Hz- 16 kHz, (-10 dB with reference to 1 kHz), complete all as specified and as directed. MAKE :- Notifier NF-SP100CI/UL or equivalent model of JC, Esser

Supply, installation, testing and commissioning of UL listed Digital Audio Amplifier capable of accessing and processing one of up to eight audio channels on the DVC audio loop, amplifying the signal and distributing it via eight Class B (speaker line) outputs having two wire digital audio ports to connect to wire DAL (digital audio loop) segments, Firefighter telephone riser supporting 7 active firefighter telephones, 100 W total output at 70 V (RMS) complete all as specified and as directed. MAKE :- Notifier DS-DB + DS-AMPE or equivalent of JC, Esser

M&L for 1.1 KV grade copper conductor, XLPE insulated armoured cable of size 4 core 10 sq.mm conforming to IS 7098 (Part 1): 1988, having stranded aluminium compact shaped conductors as per Cl. 2 of IS 8130: 1984, PVC inner sheath, single armouring of galvanised steel strip/wire and PVC Type ST-2 outer sheath conforming to IS 5831: 1984, including necessary clamping / dressing with cable ties and termination complete all as specified and as directed. MAKE :- Polycab, Havells, Finolex

S&F of PN 1.6 rated 25 mm dia full bore, two piece design, quarter turn, lever operated brass ball valve having nickel-plated forged brass body & end connector, brass chrome plated ball, PTFE body seat ring & packing, H.T. brass stem, nut & gland, rubber 'O' ring, powder coated MS lever and screwed female ends, etc. with accessories complete as specified and as directed. MAKE :- Leader, Sant, Venus

S&F of orifice plate made out of 6 mm thick SS 304 with orifice of required size to be fitted between flange and landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete all as specified and as directed. MAKE :- Newage, AAAG, Minimax

M&L for FM approved and UL listed 25 mm dia compact 3 position ball valve with drain orifice (test and drain valve) to test and drain water flow through sprinkler systems having OFF-TEST-DRAIN position, integral sight glass, rated pressure 300 psi, orifice size 15 mm and K factor 5.6, conforming to NFPA 13, along with necessary accessories complete all as specified and as directed. MAKE :- Tyco, HD, Viking

M&L for FRLSH fire survival control cable of size 2 core, 1.5 mm² (for instrumentation) with circuit integrity, conforming to BS 7846 and rated for 600 Volts, having plain annealed stranded copper conductor with fire-resistant mica tapes covered by an extruded layer of cross-linked polyethylene, extruded layer of thermoplastic low smoke zero halogen (LS0H) compound, single layer of galvanized steel wires and thermoplastic LS0H compound sheath, suitable for operating temperature range -40 ˚C to +90 ˚C and minimum bending radius being 12 times the overall cable diameter, including laying, clamping, termination and ferruling complete as specified and as directed. MAKE :- Polycab, Havells, Finolex

S&F 9 Kg capacity dry chemical powder (ABC) type fire extinguisher, conforming to IS 15683: 2006, with initial filling in brand new cylinder with powder coated finish, fitted in gun metal union, high pressure CO2 gas cartridge, discharge hose, wall mounting bracket / floor trolley mounting accessories along with suitable signage, etc. complete all as specified and as directed. MAKE :- Safex, Agni, Ceasefire

S&F 3 kg light-weight squeeze grip CO2 type fire extinguisher, conforming to IS 15683: 2006, with CO2 gas filled in brand new seamless cylinder with powder coated finish, made out of Manganese steel with wheel type valve, discharge nozzle, bend & horn, wall mounting bracket / floor trolley mounting accessories along with suitable signage complete all as specified and as directed. MAKE :- Safex, Agni, Ceasefire

S&F 9 litre mechanical foam type fire extinguisher, conforming to IS 15683: 2006, with initial filling in brand new cylinder with powder coated finish, fitted with gun metal union, high pressure CO2 gas cartridge, hose and ABS type branch pipe and wall mounting bracket / floor trolley mounting accessories along with suitable signage complete all as specified and as directed. MAKE :- Safex, Agni, Ceasefire

S&F 9 litre water type fire extinguisher, conforming to IS 15683: 2006, with initial filling in brand new cylinder with powder coated finish fitted with gun metal union, high pressure CO2 gas cartridge, hose and ABS type branch pipe and wall mounting bracket / floor trolley mounting accessories along with suitable signage complete all as specified and as directed. MAKE :- Safex, Agni, Ceasefire,

S&F of the following type of signages made out of 3 mm thick opaque PVC foam board with computer cut, PVC non-reflective self adhesive vinyl painted foam board, complete with mirror fasteners as specified and directed by the engineer-in-charge.

Sign of size 250 mm X 300 mm reading 'IN CASE OF FIRE, USE STAIRS UNLESS INSTRUCTED OTHERWISE' in 12.5 mm block letters in red and white background, properly spaced to provide good legibility located directly above the call-button and squarely attached to the wall or partition in a way that the top of the sign is not above 2 m from the finished floor level.

Sign of size 150 mm X 600 mm, posted and maintained within each stair enclosure on every floor, indicating the number of the floor in bold type and at 75 mm high numerals in red and white background, securely attached to the stair side of the door in a way that the bottom of the sign is not above 1.5 m from the finished floor level

Sign of size 150 mm X 600 mm, posted and maintained at each lift landing and on the side of the stairway door from which egress is to be made on every floor, indicating the lift / lift bank / stairway by an alphabetical letter in bold type and at 75 mm high letters in red and white background, securely attached to the side of the stairway door from which egress is to be made in a way that the bottom of the sign is not above 1.5 m from the finished floor level

DG SET

Supply, install, testing and commissioning of Silent Diesel Engine Generating Set, 100 kVA / 80 KW (3-Ph), water cooled, powered with Engine developing minimum 126.5 BHP at 1500 RPM, coupled with 415 V, 50 Hz, 3 phase, 0.8 p.f, suitable alternator, 12V Battery with ARAI approved acoustic enclosure & compliance to CPCB–IV+ norms along with MCCB based AMF logic control panel & SMPS battery charger, tools and spares complete all as specified and directed and comprising of the following:- (a) Engine : Diesel engine, 4 cylinder engine developing required minimum 126.5 BHP @ 1500 RPM for prime rating of suitable for 100 KVA alternator confirming to BS 5514/1SO 3046 and revised editions as applicable standard Totally enclosed, electric star, compression ignition, 4 stroke. The engine shall consists of following specifications:- 1. Mechanical FIP 2. Mechanical governor 3. Turbocharger, exhaust manifold, stainless steel exhaust flexible connection 4. Radiator Cooled with after cooled 5. Plate type lube oil cooler 6. Filter-fuel, lube oil 7. Dry type replaceable paper element air cleaner 8. Flywheel housing and flywheel to suit single bearing alternator 9. Starting motor – Electric, battery charging alternator 10. First fill lube oil and coolant

(b) Alternator: Alternator rated 100KVA , 0.8 PF, 415 V, 3 Phase ,4 Wire ,4 pole , 50HZ with standard design band of voltage regualtion +/- 1% from no load to full load and comprising of following specifications:- 1. brushless alternator 2. Self-excited, self-regulated 3. Class ‘H’ insulation 4. Salient pole revolving field 5. Single bearing sealed type 6. Automatic voltage regulator (c) Acoustic enclosure: – Engine alternator assembly mounted on AVM with Silencer and S.S exhaust bellow suitably optimized to meet stringent sound emission standards as laid down by MOEF / CPCB. Base rail with draw-out type fuel tank with capacity 250 Ltr is provided with a drain plug air Vent inlet and outlet connections, level indicator, manhole etc. Sub-base fuel tank with 13 hours capacity at 75% load. 12 V 88AH dry, batteries with connecting leads and terminals complete. (d) Control panel: Powder coated control panel manufactured with CRCA sheet provides: 1. MCCB of suitable rating with overload and short circuit protection 2. Controller which displays voltage, current, KW, PF, Frequency, KWh. 3. Indicating lamps for “Load On” and “Set Running” 4. Current transformers of suitable ratings 5. Copper cable of suitable capacity with incoming and 6.Outgoing terminations 7. Control fuses duly wired and ferruled

(e) Power cables: Uninyvin copper conductor cables between Alternator & Control panel inside the canopy (f) Electrical Systems: Alternator Space Heater / Higher Rating Battery / BatteryCharger / Copper Bus Bar / Sealable kWh / Earth Fault Relay / Remote Annunciator / Remote monitoring / Type RTD/BTD Temperature Scanner (g) Exhaust Silencer - Hospital / Residential grade, stainless steel, flexible pipe. Fuel System: Flexible Fuel Lines / SS fuel lines / Fuel Pressure Gauge Enclosed Unit: Sound Enclosure – Super silent / External 990 Lt. Fuel Tank. Miscellaneous: Air Cleaner (Heavy Duty)/Air Cleaner Restriction Indicator Digital / Closed crankcase ventilation (h) AMF &Synchronizing System: AMF panel / AMF with Auto-synchronization with all necessary control units, MCCBs/ contactors, MCBs etc complete set ready to operate including necessary cable connections.

MODULAR KITCHEN ITEMS

S&F perforated cutlery basket of size 530x505x100mm fabricated, purpose made with stainless steel of grade 340, not less than 6 to 8 Kg each rack, using square hollow tubes for frame work and solid round bars / 26 gauge thick sheet to make desired pattern, suitable for sliding under kitchen platform on a pair of channels, including fixing with steel screws, fixed in repairs, complete all as specified and as directed by Engineer-in-Charge. NOTE :- Telescopic channels shall be measured and paid separately under respective items of BOQ.

S&F stainless steel cup & saucer 530x505x100mm, fabricated purpose made with each stainless steel of grade 340, not less than 6 to 8 Kg each rack, using square hollow tubes for frame work and solid round bars / 26 gauge thick sheet to make desired pattern, suitable for sliding under kitchen platform on a pair of channels, including fixing with steel screws, fixed in repairs, complete all as specified and directed by Engineer-in-Charge. NOTE :- Telescopic channels shall be measured and paid separately under respective items of BOQ.

S&F perforated thali of size 530x505x200mm fabricated purpose made with each stainless steel of grade 340, not less than 6 to 8 Kg each rack, using square hollow tubes for frame work and solid round bars / 26 gauge thick sheet to make desired pattern, suitable for sliding under kitchen platform on a pair of channels, including fixing with steel screws, fixed in repairs, complete all as specified and as directed by Engineer-in-Charge. NOTE :- Telescopic channels shall be measured and paid separately under respective items of BOQ.

S&F plain basket 710x505x200 mm size fabricated purpose made with stainless steel of grade 340, not less than 6 to 8 Kg each rack, using square hollow tubes for frame work and solid round bars / 26 gauge thick sheet to make desired pattern, suitable for sliding under kitchen platform on a pair of channels, including fixing with steel screws, fixed in repairs, complete all as specified and as directed by Engineer-in-Charge. NOTE :- Telescopic channels shall be measured and paid separately under respective items of BOQ.

S&F fixed pull out 3 shelf, fabricated purpose made with stainless steel of grade 340, not less than 6 to 8 Kg each rack, using square hollow tubes for frame work and solid round bars / 26 gauge thick sheet to make desired pattern, suitable for sliding under kitchen platform on a pair of channels, including fixing with steel screws, fixed in repairs, complete all as specified and as directed by Engineer-in-Charge. NOTE :- Telescopic channels shall be measured and paid separately under respective items of BOQ.

S&F fixed multipurpose double tier 456x170x450 mm fabricated purpose made with stainless steel of grade 340, not less than 6 to 8 Kg each rack, using square hollow tubes for frame work and solid round bars / 26 gauge thick sheet to make desired pattern, suitable for sliding under kitchen platform on a pair of channels, including fixing with steel screws, fixed in repairs, complete all as specified and directed by Engineer-in-Charge. NOTE :- Telescopic channels shall be measured and paid separately under respective items of BOQ.

NOTE for item Nos. 22.01 to 22.06:- Model of reputed make (as per recommendation of modular kitchen manufacturer) shall be approved by GE.

S&F Telescopic channels soft closing, powder coated with ball bearings, suitable for sliding SS plate racks, 60 cm long, standard width, fixed over second class hard wood rectangular fillet sectional area exc. 3 sq.cm & n.exc. 6 sq.cm, clean swan secured with screws and the fillet fixed on Cuddappa stone with screws, all as specified and as directed.

S&F stainless steel handle oval shape fabricated type anodized 150mm long of approved design, shape and make fixed in repairs with nut screws & washers complete with ISI mark all as specified and as directed.

S&F stainless steel finish soft closing hinges approved design, shape and make fixed in repairs with nut screws & washers complete with ISI mark all as specified and as directed.

S&F 18mm thick marine plywood as per IS 710 laminated sheet 1.25mm thick of colour as approved by GE to frame and shutter for kitchen cabinets complete all specified and as directed.

MISCELLANEOUS ITEM S & F retro reflective sign board of size 4'x3'fixed both sides on stainless steel board made out of aluminium composite panel (ACP) sheet, 3mm thick fixed on SS-304 series bollow tubular tape of quality high intensity chequered type blue colour, appproved shape. the sign board shall be supported on 2 Nos post of 60mm dia stainless steel pipe, 304 series 3 mtr long with round moulded design on top duly embedded in ground including excavation and earth work, PCC(1:3:6) foundation complete all as specified and as directed.

Supply, install, testing & commissioning of 08 Passengers Lifts (544 Kg) suitable to serve G+5 upper floors with AC variable voltage & variable frequency (VVVF) drive complete with all standard accessories, simplex collective automatic & manual dual controlled operation with/without attendant, automatic centre opening doors with VVVF door drive (electric motor driven mechanism), sliding stainless steel doors, automatic rescue device (ARD) system, Over load device, 3D infra red sensor in full height of door & built in announcing system with hand set (02 Nos), one each in car & near Ground floor landing door and one with hand set in Machine room) complete all as specified below :- MAKE :- OTIS, KONE, THYSSEN KRUPP, SCHINDLER, MITSUBISHI, HITACHI, TOSHIBA (a) Type of Lifts : 08 Passengers (b) Load capacity : 544 Kg (c) Speed : 1.5 mtr/sec with variable speed motor (d) Power Supply : 415 volts, 3 phase AC, 50 Hz (e)Type of Drive : AC variable voltage & variable frequency drive along with converter unit. (f) Type of Machine : Low inertia gearless permanent magnet Synchronous motor, directly coupled Horizontal traction machine. (g) Car size (Inside) : Not less than 1.43Sqm. (h) Car door & landing door at all floors : Automatic Centre / opening with VVVF door drive, opening size not less than 800 mm x 2000 mm, sliding type, fabricated by stainless steel sheet as per OEM. (i) Car enclosure:

(i) Manufactured with stainless steel frame stainless steel sheet as per OEM with hair line finish (N-304) having stainless steel false ceiling with hair line finish, internal lighting arrangement with Four Nos LED light fitting for commercial supply and one No LED for emergency light, internal ventilation system provided with concealed arial flow/cross flow fan with auto cut off system and stainless steel grill/wire mesh for protection. (ii) Provision of standard thickness stainless steel hand rail 40mm dia inside the car cabin. (1 Sides) (j)Terminal buffers : Metal special spring/oil buffers as per manufacturer specification. The buffing stroke should not be less than 200mm. (k) Door opening (Inside) : Protected by centre opening stainless steel doors with hairline finish doors with clear opening size not less than 800 x 2000mm . (l) Car & counter weight Guide : Guide rails of `T' Section Mild steel as per OEM design. Counter weight shall be cast iron as recommended by OEM.

(m) Flooring : Granite not less than 18mm thick (o) Signals: (i) Combined luminous hall buttons with LCD/VFD hall position indicators at all floor. (ii) LCD/VFD for car position indicator to be fitted in COP made of stainless steel. (iii) One No car operating panel with luminous buttons in car (stainless steel). (iv) Car direction indicator in car & Landing (v) Battery operated alarm bell & emergency light (rechargeable) along with suitable maintenance free battery. (This system should be separate from ARD batteries). (vi) Overload warning feature in car cabinet(Display & announcing both type). (vii) Fireman’s switch one No per lift to be installed at ground Floor near landing door. (viii) All signal fixture & car operating panel on stainless steel face plate with hair line finish. (ix) Infra red door sensor safety edge of door for entire height. (x) Built in announcing system with hand set.02 Nos (One for lift car & ground floor landing door & one announcing system with hand set in machine room). (p) Stops & Opening : 6-6 Stop and center opening at all floors.

(q) Safety Device : (i) Automatic rescue device (ARD)/Automatic landing device with maintenance free battery having suitable capacity. The ARD panel must have auto charging facilities for battery. (ii) The ARD actuation should be after failure of power supply and when ARD is operative the car should stop at the nearest floor and then automatically open. (r) Operation: Simplex, full collective automatic operation with/without attendant. (s) Machine Room : Located about the hoist way (details as per Bldg drg) (t) Hoist-Way Constn : Existing at site, details as per Bldg drg (u) Civil Work : Necessary Civil work such as making good disturbed surface, modification to landing space to suits to car size necessary foundation to machine. (v) Control system : shall be enclosed loop type. (w) Door shall have AC-VVVF controlled close loop operated. (x) Face plate shape shall be rectangular and stainless steel with hairline finish. (y) counter weight shall be of cast iron or as recommended by OEM.

(z) One number wall mounted type telephone instrument of make Crompton Greaves / Beetel /OEM own make installed inside of car cabin along with fixing arrangement and telephone cable of suitable size from car cabin to machine room run along with trailing cable. The telephone instrument shall be connected in the telephone DB installed in the machine room. (za) One number electrically operated siren, operating voltage 240 volts having audible range of 0.5 Km of Make : KHERAJ Model No SS050 /OEM own make alongwith One Number inverter unit of suitable capacity but not less than 0.5KVA comprising of maintenance free battery connected with charging system including a separate switch/push button inside of car panel and electric wiring circuit upto the machine room. The siren shall be installed over the building at appropriate place and to be operated from inside the car. (zb) 5 W LED light Fixture (5 nos.) (zc) 250 mm sweep Fan (1 nos.) NOTE :- The contractor shall obtain necessary approval from local / state / Central Government Authority and make arrangement for inspection & test required. Contractor shall submit required certificate/license from competent authority before commissioning/ handing over or as directed by Engineer-in-charge.

Supply, install, testing & commissioning of 13 Passengers Lifts ( 884 kg) suitable to serve G+5 upper floors with AC variable voltage & variable frequency (VVVF) drive complete with all standard accessories, simplex collective automatic & manual dual controlled operation with/without attendant, automatic centre opening doors with VVVF door drive (electric motor driven mechanism), sliding stainless steel doors, automatic rescue device (ARD) system, Over load device,3D infra red sensor in full height of door & built in announcing system without hand set (02 Nos, one each in car & near Ground floor landing door and one with hand set in Machine room) complete all as specified below :- MAKE :- OTIS, KONE, THYSSEN KRUPP & SCHINDLER, MITSUBISHI, HITACHI, THOSHIBA (a) Type of Lifts : 13 Passengers (b) Load capacity : 884 kGs (c) Speed : 1.5 mtr/sec with variable speed motor (d) Power Supply : 415 volts, 3 phase AC, 50 Hz (e)Type of Drive : AC variable voltage & variable frequency drive along with converter unit. (f) Type of Machine : Low inertia gearless permanent magnet Synchronous motor, directly coupled Horizontal traction machine. (g) Car size (Inside) : Not less than 2.20 Sqm. (h) Car door & landing door at all floors : Automatic Centre opening with VVVF door drive, opening size not less than 900 mm x 2000 mm, sliding type, fabricated by stainless steel sheet as per OEM. (i) Car enclosure:

(i) Manufactured with stainless steel frame stainless steel sheet as per OEM with hair line finish (N-304) having stainless steel false ceiling with hair line finish, internal lighting arrangement with Four Nos LED light fitting for commercial supply and one No LED for emergency light, internal ventilation system provided with concealed arial flow/cross flow fan with auto cut off system and stainless steel grill/wire mesh for protection. (ii) Provision of standard thickness stainless steel hand rail 40mm dia inside the car cabin. (3 Sides) (j)Terminal buffers : Metal special spring/oil buffers as per manufacturer specification. The buffing stroke should not be less than 200mm. (k) Door opening (Inside) : Protected by centre opening stainless steel doors with hairline finish doors with clear opening size not less than 900 mm x 2000 mm . (l) Car & counter weight Guide : Guide rails of `T' Section Mild steel as per OEM design. Counter weight shall be cast iron as recommended by OEM. (m) Flooring : Granite not less than 18mm thick (o) Signals : (i) Combined luminous hall buttons with LCD/VFD hall position indicators at all floor. (ii) LCD/VFD for car position indicator to be fitted in COP made of stainless steel. (iii) One No car operating panel with luminous buttons in car (stainless steel).

(iv) Car direction indicator in car & Landing (v) Battery operated alarm bell & emergency light (rechargeable) along with suitable maintenance free battery. (This system should be separate from ARD batteries). (vi) Overload warning feature in car cabinet(Display & announcing both type). (vii) Fireman’s switch one No per lift to be installed at ground Floor near landing door. (viii) All signal fixture & car operating panel on stainless steel face plate with hair line finish. (ix) Infra red door sensor safety edge of door for entire height. (x) Built in announcing system without hand set.02 Nos( One for lift car & ground floor landing door &one announcing system with hand set in machine room). (p) Stops & Opening : 6-6 Stop and center opening at all floors. (q) Safety Device : (i) Automatic rescue device (ARD)/Automatic landing device with maintenance free battery having suitable capacity. The ARD panel must have auto charging facilities for battery. (ii) The ARD actuation should be after failure of power supply and when ARD is operative the car should stop at the nearest floor and then automatically open. (r) Operation: Simplex, full collective automatic operation with/without attendant.

(s) Machine Room: Located about the hoist way (details as per Bldg drg) (t) Hoist-Way Constn : Existing at site, details as per Bldg drg. (u) Civil Work : Necessary Civil work such as making good disturbed surface, modification to landing space to suits to car size necessary foundation to machine. (v) Control system : shall be enclosed loop type. (w) Door shall have AC-VVVF controlled close loop operated. (x) Face plate shape shall be rectangular and stainless steel with hairline finish. (y) counter weight shall be of cast iron or as recommended by OEM. (z) One number wall mounted type telephone instrument of make Crompton Greaves / Beetel /OEM own make installed inside of car cabin along with fixing arrangement and telephone cable of suitable size from car cabin to machine room run along with trailing cable. The telephone instrument shall be connected in the telephone DB installed in the machine room.

(za) One number electrically operated siren, operating voltage 240 volts having audible range of 0.5 Km of Make : KHERAJ Model No SS050 /OEM own make alongwith One Number inverter unit of suitable capacity but not less than 0.5KVA comprising of maintenance free battery connected with charging system including a separate switch/push button inside of car panel and electric wiring circuit upto the machine room. The siren shall be installed over the building at appropriate place and to be operated from inside the car. (zb) 5 W LED light Fixture (5 nos.) (zc) 250 mm sweep Fan (1 nos.) NOTE :- The contractor shall obtain necessary approval from local/state/central Government Authority and make arrangement for inspection & test required. Contractor shall submit required certificate/license from competent authority before commissioning/ handing over or as directed by Engineer-in-charge.

M&L for Galvanised iron strip of size 32 mm x 6 mm, buried in ground, complete with all accessories as specified and as directed.

SCH 'A' PART- XV WORK (COMPREHENSIVE MAINTENANCE OF LIFTS AFTER SUCCESSFUL COMPLETION OF DEFECTS LIABILITY PERIOD)

Comprehensive maintenance and repair of Passenger lift (02 numbers) having capacity 08 passengers (544 Kgs) as installed vide BOQ item No. 23.01 complete all as specified and directed.

(i) First Year after expiry of defect liability period (i.e for 3rd year)

(ii) Second Year after expiry of defect liability period (i.e for 4th year)

(iii) Third Year after expiry of defect liability period (i.e for 5th year)

Comprehensive maintenance and repair of Passenger lift (02 numbers) having capacity 13 passengers (884 Kgs) as installed vide BOQ item No. 23.06 complete all as specified and directed.

(i) First Year after expiry of defect liability period (i.e for 3rd year)

(ii) Second Year after expiry of defect liability period (i.e for 4th year)

(iii) Third Year after expiry of defect liability period (i.e for 5th year)

P L ADKE (BID ID -3161488)

CHHABINDRA KUMAR PRADHAN (BID ID -3159143)

Mukund Enterprises (BID ID -3159876)

SHREE GURUKRUPA CONSTRUCTION CO. (BID ID -3159343)

Sharda Infratech (BID ID -3161020)

SHREE KRISHNA INFRASTRUCTURE (BID ID -3161386)

MUKESH CONSTRUCTION CO (BID ID -3161268)

K R TRADERS (BID ID -3161358)

Arun Kumar Deedwania (BID ID -3161610)