SPECIAL REPAIR OF HEALTH AND WELLNESS CENTRE IN PHC GURYANI IN REWARI DISTT (RE-INVITED)

Amount

Scraping of Cement plaster (HSR 8.32 c)

12mm thick cement plaster 1:4 (HSR. 15.5)

Preparation of plastered or concrete surfaces for painting, including sand papering the surface, applying one coat of linseed oil and filling with approved quality filler, consisting of white lead, linseed oil , varnish and chalk mitti including finishing surface to the required finish, complete. (HSR.16.24)

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (J.K./ Birla). (HSR 16.81)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work (HSR. 16.58)

Providing two coats of exterior acrylic emulsion paint (a) 2nd quality (HSR 16.79)

Dismantling white or coloured glazed tiles (to be carefully removed) (HSR 8.38)

Factory manufactured solid flush door shutters, with block board core as per I.S.No.1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot pressesd, conforming to I.S.2202 part I and II, fixed in position, including iron hinges,screws,chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above,butincluding labour for fixing the same in position)-(a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges. [17.93 a ](III)35 mm thick

Factory manufactured panelled door or glazed window, shutters of commercial hard wood,such as hollock, champ,(non-coniferous timber other than teak,conforming to I.S.specification No.1003,kiln-seasoned),with 100 mm wide verticle styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks/cleats, stops, nails etc., complete, fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position). 35mm thick [HSR 17.90 b]

Applying pink primer or aluminium priming ocat on wood work including preparation of surface, Knotting and stopping etc. [HSR 16.2]

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. With second quality paint. [16.3]

Providing and laying required size of glazed tiles with DESIGN PRINTED for Windows & Door Borders (Satin finish) in dado set in CM 1:3 with joints so as to form a true & even surface and joints finished neatly with white cement mixed with matching pigments all complete as directed. (Rate should include base plastering with CM 1:5 of required thickness.) (NS)

Two range of curtain cloth – Type 1 - II. Both for doors, windows and partions. Assorted colours plain & prints. Stitched as per site/ size requirement. Minor modifications in stitching as per site/ size requirement. Preferred colour (Brown, Cream, Beige).Curtain price (including cloth & curtain rod) to be quoted in Squre metre. Stitching for each curtain to be absorb in the price of the cloth generally 2 meters.Fast colours, water wash.Fabric density Non Transparent Composition. Fabric of curtain shall be soft texture, great shading, drape effect and nice dobby. The bracket shall be side mounted and front mounted as required. First rod mount is 3.5 inches from the wall. Where curtain used as a partition/ long length, sufficient support from ceiling should be provided to avoid sagging.Rate quoted for fully stitched Curtain with top nepha with punch holes after lining bucramreinforced with SS / PVC islets and lower nepha 200mm double turned. Type - II (Window & Door Curtain)Curtain fabric weight shall be up to 250-275 (±5%) gsm Composition of fabric shall be polyester yarn I.E. 300 denier fast colour sink age shall be (±5%) Weft and warp shall be polyester / cotton polyester mix (NS)

Terracing consisting of tiles 22.86 cm x 11.43 cm x 3.81 cm laid over 87.50 mm mud filling on a layer of 25mm mud palster and another layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 Kg. per sqm. on top of R.C.C. slab including grouting with cement sand mortar 1:3 ad top surface to be left clean etc. (HSR 13.13)

Providing & fixing vitrified tiles of size 600x600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand morter 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles, Note:- Tile shall be premium quality (First quality) of reputed manufacturar like NITCO, KAJARIA, SOMANI, ORIENT , JOHNSONS & RAK.( HSR.14.89)

Providing & Fixing vitrified tiles of size 600mmx600mm of approved make in skirting or Dado in any pattern as specified over base of 12 mm thick cement coarse sand morter 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:- tile shall be of premium quality( 1st quality) of reputed manufacturar like NITCO, KAJARIA,SOMANI, ORIENT, JOHNSONS & RAK.( HSR.14.90)

Providing & fixing polycarbonate sheet - roofing i/c cost of sheet, screws etc. comp, fixed in position to the satisfaction of officer / official-in-charge. (NS)

Painting two coats excluding priming coat with ready-mixed paint for metallic surfaces in all shades on new steel or iron work. (HSR 16.17)

Earth work in excavation in foundations, trenches, etc.in all kinds of soils, not exceeding 2 metres depth including ressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as irected within a lead of 30 metres (HSR 6.6)

Cement Concrete 1:4:8 with stone aggregate 20mm nominal size in foundationand plinth. (HSR 10.39)

First class brickwork laid in cement sand mortar 1:6 in foundation and plinth. (HSR 11.2)

Damp proof course 25 mm thick of cement concrete 1:2:4 using stone aggregate 20mm nominal size with 2 coats of bitumen 20/30 penetration, at 1.65 Kg per sqm laid hot and sanded. (HSR 10.114)

First class brickwork laid in cement sand mortar 1:6 in first storey upto 4 meters above plinth level.(HSR 11.7)

Earth filling under floors with surplus soul, excavated from foundation and taken only from outside the building plinth, in15 cm layers including ramming watering and consolidating lead upto 30 metres (HSR 6.13a)

Cement concrete 1:1.5:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respect. [HSR. 10.82 + 10.95 (a)].

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coasts of bitumen laid hot at 1.65 Kg per sqm on top of R.C.C. slab including grouting with cement sand mortar1:3 and top surface to be left clean etc. (HSR 13.13)

Providing & fixing PVC Rain Water pipe 6kg. Presure of ISI mark in cement mortar during masonry work. (HSR 13.89)

25 mm thick conglomerate floor of cement concrete 1:2:4 over flat brick blocks 34.29 cm x 45.72 cm x 45.72 cm with second class bricks, grouted in cement sand mortar 1:6 with 25 mm wide open joints, alround filled with cement concrete 1:2:4 simultaneously with topping over 100 mm sand filling. (HSR 14.14)

Providing and fixing 1st quality ceramic-glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer -In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. [HSR 14.92 (b)]

Providing and fixing ceramic-tiles / anti-skid tiles of size 400x400mm or above size of approved make in floors laid in any pattern over base of 20 mm thick Cement Sand Mortar 1:3 and jointed with white cement slury mixed with pigment to match the shade of tiles. [HSR 14.91] Note:-Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA,RAK. [HSR 14.91]

12 mm thick cement plaster 1:6 (HSR 15.7)

15 mm thick cement plaster 1:6 on the rough side of single or half brick wall (HSR 15.12)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or matallic or plastered or concrete surfaces to give an even shade. (HSR 16.3)

Providing & applying two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete (J.K. / Birla make). (HSR 16.81)

Providing two coats of exterior acrylic emulsion paint. (HSR 16.79 (a))

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (HSR 16.58)

Factory manufactured solid flush door shutters, with block board core as per I.S.No.1659- 1969 bonded with water proof type phenol formaldehyde synthetic resin,hotpressesd, conforming to I.S.2202 part I and II, fixed in position,including iron hinges,screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above,but including labour for fixing the same in position)- (HSR 17.90a + 17.18 Note)30mm thick

Wrought iron and mild steel (using angles, flats, square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors (HSR 18.12)

Fe - 500 EQR TMT Steel bars for R.C.C., works, where not including in the complete rate of R.C.C., including bending binding and placing in position complete. [HSR 18.22]

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, door and window frame of size 114 mm X 50 mm with 35 mm wide double rebate (HSR 18.34 d)

Finishing walls with exterior decorative cement based paints such as snowcem, Robbiacem etc. on new work, two coats to give an even shade. (HSR 16.61)

Factory manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash,etc.,( HSR 17.92)

Providing & fixing printed Ayushman Bharat Ceramic Tile of approved make laid in any pattern as specified by the Engineer -in Charge of work including Ayushman Logo & Beti Bachao, Beti Padhao and Door & window frame flower Bail, Health & wellness Centre logo, Signage of Ayshman complete in all respect as per PWD specification. (NS)

P.H. Items :- PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (as approved by the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT, SYPHONIC TYPE, consisting of- Mixed colour (HSR 30.5 (b) (iii))

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE SHOWER WITH 15 OR 20 I/D IN-LET.125 mm diameter [HSR 30.66 (i)]

PROVIDING AND FIXING IN POSITION BEST QUALITY STAINLESS STELL SINKS WITH COMPLETE FITTINGS. AS FULLY DESCRIBED IN ITEM NO.30.51 ABOVE. 530mm X 450mm X 175mm [HSR 30.53(b)]

Providing and fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing over flow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks completein all respects to the satisfaction of Engineer-In-Charge. (Except civil work).(HSR 30.119)

CONSTRUCTION BRICK MASONRY INSPECTION CHAMBER SIZES AS GIVEN BELOW UPTO 0.60 METRE AVERAGE DEPTH in cement mortar 1:5 LIME CONCRETE with 40 percent lime mortar 2:3 in foundation cement concrete 1:2:4 BENCHING 12mm THICK CEMENT PLASTER 1:2 with a floating coat of 1mm thick of neat cement R.C.C.1:2:4 SLAB 100mm THICK /C.C.TOPPING 50 mm THICK WITH 455 MMx455MM/455MMx610MM INSIDE LIGHT DUTY C.I.INSPECTION CHAMBER COVER AND FRAME weight as per I.S.I. specification painted WITH 3 COATS OF black bitumastic superior paint complete as per standard design. (b) Size 450 mm X 600 mm inside (with 455 mm x 610 mm cover and frame single seal pattern I weighing 38 kg with C.C. topping)

PROVIDING AND FIXINGIN POSITION GULLY TRAPS FIXED IN CEMENT CONCRETE 1:4:8 complete WITH H.C.I.GRATING 150 MM X 150 MM CAST IRON COVER WEIGHING APPROXIMATELY 7.26 K.G. AND FRAME CLEAR OPENING 300 MM x 300 MM and outside size 330 MM x 330 MM AND CHAMEBR INCLUDING cost of all brick work in CEMENT MORTAR 1:5 CEMENT CONCRETE 1:8:16 IN FOUNDATIONS, AND CEMENT CONCRETE 1:2:4 IN COPING around C.I. cover and frame etc. WITH THREE COATS of black bitumastic superior PAINT of approved manufacture on all C.I. work AS PER STANDARD DESIGN, minimum depth of water should be 150mm with a minimum seal 50mm. (b) 100 mm internal diameter H.C.I. gully trap (HSR 30.114 (b))

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE VITREOUS CHINAWARE SINKS WITH COMPLETE FITTINGS AS FULLY DESCRIBED IN ITEM NO.30.51 ABOVE. White (a) 600mm X 450mm X 200mm (HSR 30.52 (a))

Providing for laying jointing, fixng and testing G.I. (Medium Class "B” type of Tata & Jindal make) pipe lines and special tees bends, sockets, elbows etc. inside building and tetsting etc complete including cuttin threading. Including cost of Special G.I, special shall be of make:- UNIK, TATA, ZOLOTO (NS) (a) 20 mm internal diameter of pipeline

sahil

Yogesh Kumar Contractor

Pawan