SPECIAL REPAIR TO CERTAIN OMQs/SMQs IN DOMESTIC AREA AND MINOR WORKS AT DIFFERENT LOCATIONS

Amount

SCHEDULE A BOQ

M&L Treatment of the damaged sunken floor slab comprises of the following specification and all as specified and as directed. Make :- Dr Fixit/ M/s Sika india Pvt Ltd/ STP Ltd/ M/s Fosroc Chemicals

(a) Demolition of cement concrete filling of any description in sunken portion in toilet and removing debris outside MD land.

(b) Cleaning the sunken/ lowered portion of RCC slab surfaces (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely. 40mm thick avg PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in padding concrete to achieve proper slope including cutting holes in bricks or RCC wall for spout (Quoted rate shall be deemed to be inclusive for WPC )

(c) Rendering of uneven surfaces with 10mm thick in CM 1:4 mixed with integral water proofing compound @ 3% by wt of cement consumed. Fill it with water and check dampness and seepage. Where dampness/ seepage is noticed, nozzles shall be fixed and grouting carried out. (Quoted rate shall be deemed to be inclusive for WPC )

(d) All junctions points of side wall where CI/ GI pipes are passing through shall be sealed with epoxy putty.

(e) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean.

(f) M&L for applying two coats of polymer modified cementious water proof coating as per manufactures instruction to bottom and vertical sides up to finished floor level+100mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion all as specified and directed

(g) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with integral water proofing compound 3% by wt of cement consumed as per manufacturers specification including rounding of corners and junctions sloping towards spout. (Quoted rate shall be deemed to be inclusive for WPC)

(h) PCC 1:5:10 type E2, using 40mm thick graded stone aggregate, complete all as specified

(j) PCC 1:2:4 type B0, using 12.5mm thick graded stone aggregate, complete all as specified

Note for item No 2 to 11 :- Test the water proofed area (ponding test) by filling water for at least 72 hours and tested for leakage, seepage and to the entire satisfaction of GE. Test shall be done in presence of reps of Engineer-in-Charge and record for each sunken slab shall be maintained. The treatment shall be carried out by authorised applicators of chemicals. Cost of testing is include in the rates quoted above.

S&F in repairs vitreous china squatting pan 'Orissa' Pattern size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe ) including provision of lime concrete bedding all as specified and as directed.

S&F PVC (SWR) S trap 125/110mm bore Including taking down existing one complete all as specified and as directed by Engineer-in-Charge

S&F in repairs Bib Cock with wall flange screwed down screwed for iron pipe 15mm bore complete all as specified and as directed. Make as per CAT Part No CQT -23047 of Jaquar or equivalent to /Parryware/Hindware/Cera

S&F in repairs 20 mm outer dia of pipes 3-layer PP-R (Polypropylene random copolymer) pipes concealed pipes SDR 7.4 (PN-16 @ 20oC) UV stablised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings, complete to walls, ceilings or in floors etc. complete all as specified and directed. Make : SFMC, KPT, Prince

Note for item No 16 :- (a) The unit rate shall be include for taking down existing pipe and connections and all fittings as directed.

(b) The unit rate shall include the cost of short lengths, with all pipe fittings such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc and fixing accssories such as pipe hooks, screws clamps etc

(c ) Wall thickness of pipes shall be all as per IS : 15801

M & L cutting chases, pinning in. making good to facings in brick wall wherever required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S&F in repair PVC Dual flush ceramic colour , low level, 10 litres capacity, star white with inlet float ball valve, PVC flush pipe and handle, making proper fixing and hanging arrangements Cat Part No 21029 of - hindware or equivalent complete all as specified and as directed.

S&F PVC connections 15mm size with PTMT nuts of length 600 mm including taking down existing one complete all as manufactures and all as specified and directed by Engineer- In - charge.

S&F Angular stop cock with wall flange, valves high pressure screwed both ends iron pipe or for unioins 15mm dia, including taking down existing one complete as directed by Engr-in-charge. Make:- Jaquar CAT Part No CQT-23059 or equivalent to Hindware/Cera/parryware

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and M & L Joint free Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile of size exc 0.09 Sqm but n exc 0.18 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incuding screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:4) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and Material and labour for Glazed ceramic coloured tiles 450 x 300 mm x 7/8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles on vertical surface such as dado including 10mm thick 1:3 backing coat complete all as specified and directed.

Note for item No 24 & 25 :- The manufacturer's test certificate and individual test certificate of Tiles must be submitted for approval by the concerned authority prior to installation

Taking down chowkats or frames with shutter n.exc 1.5 Sqm each without taking off shutter from the frame complete all as specified and directed.

S&F Mild steel work in framed work such as grills and similar work including framed guard bars, barred iron doors, ladders, framed balusters etc., including of fixing of sheet steel or other covering to doors etc., to be prepared for hanging /sliding with or including either hooks or hinges or steel hanging door fittings etc., confirming to Fe 410-0 or Fe 310-0 work complete including Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube complete all as specified

S&F Factory made Solid PVC Door Shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified and directed.

Supply and fixing 75 mm long Butt hinges medium weight cold rolled stainless steel, and fixed complete all as specified and as directed.

Supply and fixing 150 mm long Extruded Aluminium alloy handles, cast type, anodised complete all as specified and directed.

Supply and fixing 200 mm long aluminum anodized barrel tower bolt extruded section complete all as specified and as directed.

S&F in repairs Floor door stopper of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor overall 150mm complete all as specified and as directed.

S&F in repairs 300mm long, ordinary Mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints of 110 mm bore fixed to wall including taking down existing pipe along with bends, branch pieces and fittings complete all as specified and as directed by Engineer-in-Charge

S&F PVC (SWR) bends 110mm bore complete all as specified and as directed by Engineer-in-Charge

S&F PVC (SWR) 110mm junction (single T) equal or unequal provided with access door complete all as specified and as directed.

S&F PVC (SWR) 110mm junction vent cowl complete all as specified and as directed by Engineer-in-Charge

S&F PVC (SWR) branch piece single (single Y) 75mm bore equal or unequal provided with access door all as specified and as directed by Engineer-in-Charge

S&F PVC (SWR) branch piece single (double Y) 75mm bore equal or unequal provided with access door all as specified and as directed by Engineer-in-Charge

S&F Wall mounted Shower Arms 190mm long flat shape for wall mounted shower with flange including taking down complete all as specified and directed Make :CAT Part No-SHA-483 of Jaguar or equivalent make of parriware /hindware.

S&F in repairs Overhead Shower ø120mm Round Shape Single Flow (ABS Body Chrome Plated with Gray Face Plate) with Rubit Cleaning System complete all as specified and as directed. Make :CAT Part No- OSH-1709 of Jaguar or equivalent make of parriware /hindware

S&F in repairs Chromium plated wall mixer with provision for over head shower with 115mm long bend pipe on upper side connecting legs and wall flanges complete all as specified and directed. Make:- CQT 23273 of Jaquar or equivalent in Parryware /Hindware / ESS-ESS

S&F in repairs PVC (SWR) floor trap 75mm dia of outlet pipe, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F Pillar taps 15mm bore CP with capstan head screwed down high pressure screwed for iron pipe including taking existing one complete all as specified and directed by Engr-in-charge. Make:- Cat Part No CQT -23021KN of Jaquar or equivalent to /Parryware/Hindware/ Cera

S&F Wash basin vitrous china (flat back and angle back Type) size 580x400mm including taps waste chain and plug and porceline stopper but brackets including cutting for and pinning in ends of brackets or erecting stand with waste pipe ,fixed including taking down existing one complete all as specified and directed by Engr-in-charge.

S&F 32 mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed including taking down existing one complete all as manufactures complete all as specified and directed by Engineer- In - charge

S&F 32mm bore low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sqcm for WHB including taking down complete all as specified and as directed.

S&F 40mm bore low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sqcm for WHB including taking down complete all as specified and as directed.

S&F PVC (SWR) pipes single socket in any length with rubber ring joints of 75 mm bore fixed to wall including taking down existing pipe with bend, branch piece and other fittings complete all as specified and as directed by Engineer-in-Charge

S&F PVC bends 75mm bore complete all as specified and as directed by Engineer-in-Charge

S&F PVC (SWR) 75 mm dia junction vent cowl complete all as specified and as directed by Engineer-in-Charge

S&F PVC (SWR) 75mm junction (single T) equal or unequal provided with access door complete all as specified and as directed.

S&F PVC (SWR) branch piece (single Y) 75mm bore equal or unequal provided with access door complete all as specified and as directed by Engineer-in-Charge

S&F in repair CP Soap dish CAT Part No-ACN-1131N of jaguar or equivalent make of Parriware /Hindware all as specified and as directed.

S&F in repair Towel rail 24" long for wash basin all as specified and as directed.Make: (Make : CAT Part No-ACN-1111NM of Jaguar series or equivalent make of hindware / parryware

S&F 600X450 mm bevelled edge mirror fixed with 04 Nos Stainless steel studs including taking down existing one complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

Taking down cement plaster on brick or stone walls, or concrete or ceilings etc., raking out joints, hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises, removal and depositing serviceable materials where directed and leaving the work clear of any plastering complete all as specified and directed

M & L rendering 5 mm thick on concrete surfaces in CM 1:3 finished even and smooth without using extra cement as in ceiling etc complete all as specified and directed

M&L Preparation of new plastered surface of ceiling and applying two coats of white wash complete all as specified and as directed.

M&L Preparation of new plastered surface of wall and applying three coats of white wash complete all as specified and as directed.

M & L rendering 15 mm thick on fair faces of brick work in CM 1:4 finished even and smooth without using extra cement etc complete all as specified and directed

M & L for preparation of new plastered surface of wall applying two coats of oil bound distemper over a coat of alkali resistant primer complete all specified and as directed.

M & L rendering 15 mm thick on fair faces of brick work in CM 1:6 finished even and smooth without using extra cement etc complete all as specified and directed

M&L applying two coats of cement based paint over one coat of alkali resistant primer, including preparation of new plastered wall surfaces of any description, complete all as specified and as directed.

S&F CP sink cock with swinging casted round shape spout screwed down screwed for iron pipe 15mm bore including taking down existing one complete all as specified and as directed. (Make :CAT Part No-CQT-23347 of Jaguar or equivalent Parryware/ Hindware

S&F Sinks with drainage board made of stainless steel 01 mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm fixed in repairs all as specified and directed. Make : M/s Diamond / Nirali / Amco / TATA.

S & F Waste coupling of PTMT (half or full threaded) in repairs (Minimum weight 32mm45gms/40mm-60 gms) complete all as specified and directed.

S&F Plate rack of size 65 cm x 96 cm made of stainless steel fixed in repairs complete all as specified.

M&L Water proofing treatment of existing roofs as per details given below after complete removal of existing water proofing treatment and expose of top surface of RCC slab of any thickness, any type by stripping out old tar felt over roofs, parapets, chimney stacks etc laid horizontally or vertically including taking out layer of cement plaster etc and cleaning the surface with water and using wire brush including removing debris to outside the MOD land complete all as specified and as directed.

(a) Dismantling existing cement concrete/ roof tiles on roof including removing debris to outside MOD land as directed.

(b) Bring upto the slope by providing filling of light weight materials such as cinder, light weight concrete etc as required & then providing PCC 1:2:4 type B1 using 20mm graded stone aggregates of average thickness of 50 mm.

(c) Rendering 10mm thick in CM 1:3 on concrete roof surfaces and finish the surface even and smooth without using extra cement including mixing water proofing compound as per manufacturer’s instructions.

(d) Surface should be free from any loose paint, dust or grease. Remove all existing bitumen coatings completely by using intense wire brushing, high speed water jet & vacuum cleaner for thorough cleaning of the surface to avoid ‘Peeling off’ problems.

(e) All cracks at corner joints, channels and parapets should be properly treated. For filling cracks upto 3mm crack seal material of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical to be used. Bigger cracks, damaged portions & hollow areas must be repaired with polymer modified cement mortar.

(f) Apply a coat of self priming smart care damp proof ultra (Code 5698) of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical with 33% dilution with water using brush/roller on newly plastered surface after curing as per IS-456 and allow to dry for 4 to 6 hours (dilution & forced coverage requirement strictly as per manufacturer’s instructions).

(g) After the primed surface has dried, apply first coat of water proofing smart care damp proof ultra (Code 5698) of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical using brush/roller on the same primed surface & allow to dry for 4 to 6 hours.

(h) Prepare for apply 2nd coat of water proofing smart care damp proof ultra (Code 5698) of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical using brush/roller on the same surface. The temp to be maintained 25 to 35° C through out the all above application work.

(j) In case of severe dampness an additional coat of damp proof materials to be applied.

Note for item No 72 to 81 :- (i) The work shall be carried out through authorized and qualified applicators of the following manufacturers only. MOU to be submitted before commencement of work. Make : M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical

(ii) A performance guarantee certificate and Guarentee amount equal to 3% of cost of water proofing treatment for 10 years shall be submitted by the contractor to the GE on completion of work as specified.

(iii) The unit quoted rate is deemed to include taking down of water pipeline, tanks, wires (etc) found on roof and refix at the original position after complete treatment of roof.

(iv) The unit quoted rate shall be inclusive of material, all labours, tools and plants including scaffolding required for working upto approx 7.5 mtr height from natural ground level.

(v) The unit rate quoted for item is deemed to include for Removing of accumulated earth of any width and depth upto 15 cm cleaning/cutting the grass with hand operated petrol/kerosene driven grass cutting machine and removing the grass waste around 3 m from plinth protection to outside MD land.

(vi) Adoption of necessary safety arrangement like safety belts, ropes, helmets, netting etc. which are required for safety of working labour at height exceeding 3 to 25 mtr height shall be mandatary and deemed to be included in the unit rate quoted.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed. Note :- The material obtained from demolition shall be disposal outside MD land and the unit rate is deemed to be included.

M&L PCC 1:2:4 type B-0 using 12.5mm graded stone aggregates as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L Plain cement concrete (1:3:6) type C1 (20 mm graded stone aggregate), 75mm thick, as in plinth courses, top surface of concrete finished even and smooth with out using extra cement, including expansion joint 10mm thick filled with mastic filling comprising of 01 part of heated blown bitumen and 3 parts of sand complete all as specified and directed by Engineer- In - charge.

Taking down steel tubing 15mm bore and connections including cleaning and refixing of old GI tubing 15mm bore including connections in new or old position (wall, ceiling & floor) complete all as specified and directed. . Note :- The unit rate is included for all fittings required for re-connection.

Taking down steel tubing 20mm bore and connections including cleaning and refixing of old GI tubing 20mm bore including connections in new or old position (wall, ceiling & floor) complete all as specified and directed. Note :- The unit rate is included for all fittings required for re-connection.

S&F 25mm dia mild steel powder coated drapery rod out to length required without joint in between and fixed at openings Including taking down existing one complete all as specified and as directed by Engneer-in-Charge

S&F Mild steel powder coated brackets for holding the drapory rod and fixed to wall with MS screw including taking down existing one complete all as specified and as directed.

S&F Mild steel powder coated fancy type brackets fixed at both the end of drapery rod of same colour and type of drapaery rod Including taking down existing one complete all as specified and as directed by Engneer-in-Charge

S&F in repairs 25 mm outer dia of pipes 3-layer PP-R (Polypropylene random copolymer) pipes concealed pipes SDR 7.4 (PN-16 @ 20oC) UV stablised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings, complete to walls, ceilings or in floors etc. all as specified and directed. Make : SFMC, KPT, Prince

Note for item No 96 :- (a) The unit rate shall be include for taking down existing pipe and connections and all fittings as directed.

(b) The unit rate shall include the cost of short lengths, with all pipe fittings such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc and fixing accssories such as pipe hooks, screws clamps etc

(c ) Wall thickness of pipes shall be all as per IS : 15801

S&F 20 mm outer dia PPR gate valve (brass insert) incl taking down existing one comlete all as specified and directed

S&F 25 mm outer dia PPR gate valve (brass insert) incl taking down existing one comlete all as specified and directed

Demolition of reinforced cement concrete reinforcement cut as required to facilitate of any description and in any position not otherwise specifically provided for complete all as specified and directed. Note :- The material obtained from demolition shall be disposed outside MD land and the unit rate is deemed to be included.

M&L Factory made UPVC three track sliding Window frame having 2 tracks for glass shutter and 1 track for mosquito sash made of upvc profile section of size 73mm x 42mm (wxh) having outer wall thickness of 2.0mm(+/-0.2mm). Sliding glass shutter shall be made of UPVC section of size 55mm x 33mm and sliding wire mesh shutter shall be made of UPVC section of size 40mm x 22mm. All section of the frame, sash, transom & mullion, as applicable, shall be duly reinforced with G/J/U/O shape galvanised mild steel section of required thickness considering structural / wind load requirement. System shall be provided with the suitable upvc bead for glazing of the system & fitted with inner & outer EPDM seal gaskets. Clear Glass of Saint Gobain / Modiguard make with thickness of 4mm and stainless steel wire cloth of 0.19mm nominal dia. All welded joints are to be neatly trimmed & feature grooved/raised nib finish so make the finished product free from all sharp edges & burrs. All the corner / mullion / transom joints of the frame and sash shall be mitered cut & fusion welded without any mechanical joining. System shall have adequate drainage mechanism to permit the escape of water from horizontal member beneath each sealed unit. System is to be provided with proper operating & locking hardware mechanism. Window locking system will be either both side push lock system or semi-circle locking system in centre. Complete window shall be fixed in to the existing pre finished aperture, by drilling and fixing through the outer frame using quality fasteners & silicon glue is applied to fill up the crevice between wall and window frame for leak proof installation including taking existing one complete all as specified. Note: - The contractor shall submit 5 years warranty certificate for upvc profile and 1 year warranty certificate for hardwares.

M&L Factory made UPVC Ventilators design will be like top part fixed with exhaust fan provision and bottom part with fixed louver strips.Ventilators frame made of upvc profile section of size 45mm x 43mm (wxh) having outer wall thickness of 2.0mm(+/-0.2mm). Wherever required /specified, system shall have the fix mullion of size 45mm x 60mm having outer wall thickness of 2.0mm(+/- 0.2mm). All section of the frame,transom & mullion shall be duly reinforced with G/J/U/O shape galvanised mild steel section of required thickness considering structural / wind load requirement. System shall be provided with the suitable upvc bead for glazing of the system & fitted with inner & outer EPDM seal gaskets. Pinhead Glass with thickness of 4mm required for fixed & louvers strips. All welded joints are to be neatly trimmed & feature grooved/raised nib finish so make the finished product free from all sharp edges & burrs. All the corner / mullion / transom joints of the frame shall be mitered cut & fusion welded without any mechanical joining. System shall have adequate drainage mechanism to permit the escape of water from horizontal member beneath each sealed unit. System is to be provided with proper operating & locking hardware mechanism. Complete ventilator shall be fixed in to the existing pre finished aperture, by drilling and fixing through the outer frame using quality fasteners & silicon glue is applied to fill up the crevice between wall and ventilator frame for leak proof installation including taking existing one complete all as specified. Note :- The contractor shall submit 5 years warranty certificate for upvc profile and 1 year warranty certificate for hardwares.

M&L Granite 18 to 20mm thick (table rubbed and polished) in steps,Jamps, Pillars, Windows, cills, platforms and like CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with marble shade of Granite over screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:4) all as specified and as directed. Note : (a) The Unit rate quoted is included for Demolition of Stone Slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar (b) The manufacturer's test certificate and individual test certificate of Tiles must be submitted for approval by the concerned authority prior to installation.

M&L Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat etc. complete all as specified and directed. Note: Minimum thickness of powder coating 50 micron.

S&F Powder coated aluminium door shutters,aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each shutter, hinges anodised aluminium snap beading screws etc complete all as specified and directed. Note:-Glazing and particle board work shall be measured and paid seperately.

S&F Plain sheet glass of thickness 5.50mm, ordinary quality and glazed with oil putty or fixed with aluminium frame using aluminium beading of suitable size, exc 0.5 sqm in each pane complete all as specified and directed..

S&F 12mm thick prelaminated particle board, interior grade, prelaminated both sides with decorative choice lamination fixed with screws to aluminium frame complete all as specified and as directed.

S & F brass mortice lock of size 100mm, 4 levers, vertical type complete all as specified and directed.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover governing pivot made of brass, other parts made of mild steel heavy duty including taking down existing wire cloth complete all as specified and as directed.

Excavating in post holes (or similar holes) in any type of soil each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and as directed.

M&L for PCC, type D-2, 1:4:8, using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

S&F mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 gradeSt.-240) complete all as specified and as directed

S & F Rolled mild steel in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410- W(Gde E-250) quality- 'A' complete all as specified and as directed

S & F Rolled mild steel in Joist, channel, angle, or tee sections, fixed independently confirming to Fe 410 -W (Gde- E- 250) quality A, without connecting plates, etc. cut to ordinary lengths i.e. within 20mm of the length indicated complete all as specified and directed

S&F Pre painted Coloured corrugated Galvalume roofing system sheet 0.50 mm thick having Zinc aluminum alloy coating AZ150 shall be as per IS:277/ASTM 1379 150 gsm/ sqm double ribbed trapezoidal profile steel sheet any colour having tensile strength of 550 Mpa as in Roof covering /cladding to wall fixed with self tapping screws all complete all as specified and directed.

S&F Pre-painted coloured galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all complete all as specified and directed.

Note for Pre-painted coloured Galvalume roofing :-

(i) The manufacturer's test certificate and individual test certificate for the chemical and mechanical properties of sheet must be submitted for approval by the concerned authority prior to installation.

(ii) The contractor shall ensured that no leakages take place from the roof. The roofing shall be Coloured Galvalume roofing system (olive green colour or as approved by GE) with feed material manufactured from 0.50 mm Total coated thickness (TCT), minimum 550 MPa yield strength and shall conform to the physical specifications of IS: 2062 of 2011, coated with hot dip metallic Aluminium / Zinc alloy coating AZ150 as 150 gm/sq.mt total on both sides.

(iii) The painting shall be coloured baked enamel polyester with silicon coating of film thickness 25 microns nominal on the exposed face/exterior side and on the reverse side ( interior face) shall be white with 15 microns film thickness, over a coat of 5 micron nominal thickness Primer.

M&L Preparation of new steel surfaces of any description exc 10 cm width or girth and applying Two coats of synthetic enamel paint over a coat of redoxide primer on new steel surfaces complete all as specified and as directed.

M&L Preparation of new or previously untreated steel surfaces of any description, under 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over one coat of red oxide primer complete all as specified and directed

Note for item No 123 & 124 :- (a) All synthetic enamel paint, plastic emulsion paint shall be of 1st quality manufactured by the standard firms of make as specified.

(b) The contractor shall inform the GE, within three weeks of the acceptance of the tender, the brand/names of the manufacturers of paint proposed to be used in the works and submit samples thereof and obtain prior written approval of GE before their use in works.

(c) The contractor shall when so required by the GE, produce certificate from the manufacturer or their representative to establish that the brands of paints purchased by the contractor from them, satisfy the requirements of the relevant Indian Standards. Tint of paint, will be approved by the GE.

(d) Paints shall be obtained direct from approved manufacturer or from their authorized agents only of respective brands mentioned below and brought to site in sealed containers. The paint so procured shall be of first quality of any approved make as per list of makes specified. i. Berger Paints (Luxol), ii. Jenson & Nicholson (Brolac), iii. Shalimar Paints(Superlac), iv. Goodlass Nerolac (Nerolac), v. Asian Paints(Apcolite)

(e ) Unless otherwise specified the tints of paint shall be as approved by the GE

(f) The contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the Engineer-in-Charge for approval.

(g) The surface shall be thoroughly cleaned and dusted. All dirt scales oil and grease shall be thoroughly removed before painting is started. The prepared surface shall be inspected and approved by the GE before painting is commenced. The weather shall not be foggy/rainy, dusty or windy. The suitability of the weather will be determined by the Engineer-in-Charge.

(h) No hair marks from the brush or clogging of paint buddles shall be left on the work. Surface shall ordinarily not be painted until it has dried up completely. Trial patches of paint shall be laid at intervals to check if drying is satisfactory.

M&L Hardcore of gauge not exceeding 63 mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L 100 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in base concrete complete all as specified and as directed.

M & L brickwork with fly ash’ bricks using old size bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and as directed

M & L rendering 10 mm thick on fair faces of brick work in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed

S&F Welded steel wire fabric cut to length,bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members not excceding 4Kg/Sqm complete all as specified and directed.

Surface dressing not exc 15 cm deep in soft/loose soil all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out hard/dense of soil complete all as specified and as directed.

M&L reinforced precast cement concrete 1:2:4, Type B–1 using 20mm graded stone aggregate as in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. set in cement mortar 1:4 including formwork, complete all as specified and as directed.

S&F High strength corrosion resistant TMTsteel bars of Grade Fe–500 of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified.

S&F High strength corrosion resistant, TMTsteel bar of grade Fe-500, 5 mm dia and above and up to 10 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips in stirrups , spacers and binders etc complete all as specified and directed.

M & L rendering 10 mm thick on fair faces of brick work in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed

S & F Steel door including projecting type hinges, steel handle, complete, with glazing bars, dovetailed or welded etc complete all as specified and directed

S & F Mild steel, plain, black sheet of thickness 0.8mm in wall cladding, steel gates and similar work, cut to size, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed

S & F Wire netting with size of mesh 20mm made of galvanised steel wire 1.40mm dia fixed with tinned tacks of wire staples complete all as specified and directed

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed

M&L 75mm thick, plain cement concrete (1:3:6), type C-2 (using 40 mm graded mechanically crushed stone aggregates), as in plinth protection/ path/ hardstanding including making joints @ 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling (to full depth) comprising of one part heated hot blown bitumen 85/25 & two parts heated sand (by volume), surface finished even and smooth without using extra cement complete all as specified and as directed. Note :- The concrete shall be laid at a stretch not exceeding 3 metre in length and width of joint shall not be more than 12 mm.

M&L Spreading and leveling the soils in layers not exceeding 25 cm thick in each layer including watering and well ramming complete all as specified and directed.

M&L 100 mm thick Plain cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate ) as in sub base complete all as specified and directed.

M&L 25mm thick PCC (1:2:4) type-B-0 using 12.5 mm graded stone aggregate as in floors complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed

Removing excavated material to a distance exc. 1.50km but n exc. 5km and depositing where directed complete all as specified and as directed.

M&L Plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate ) as in in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

Taking down aluminum/copper point wiring on & including hard wood battens, surface conduit and board/ blocks etc or through conduits for light, socket or power point, fan point complete (Taking down of fittings such as switches, sockets, bells, ceiling rose, holders , regulators, light fittings, MCB, lamps etc shall be measured and paid seperately) and making good the disturbed plaster surfaces of wall, floor, ceiling and painting 2 coat of white wash/distamber to meet the existing surface and removing materials and debris to reinstate the premise neat and clean complete all as specified and directed.

S&F Wiring complete with 1.5 sqmm single core PVC insulated, unsheathed FRLS 1100 volts grade,FRLS cable and incl PVC Casing Capping with accessories in wall/roof/ceiling/hangar steel frames etc incl Modular terminal boxes fabricated with 1.6mm MS sheet concealed/fixed surface to walls covered with modular white cover plate with frame etc and 1.5 sqmm PVC insulated, unsheathed copper conductor multistranded cable 1100V grade as earth continuity conductor & connecting to common earth dolly all as specified for following:-

One light point/fan/bell point controlled by one switch

All as per item No 156 here in before but for One 3 pin socket out 5 amp on the same board

All as per item No 156 here in before but for one switch socket outlet 3 pin 5 Amps on independent board

All as per Sl No 156 above but Wiring with 4 Sqmm copper multistranded unsheathed cable and 4 Sqmm copper cable for earth continuity conductor controlled by one 15A switch socket independently

Supply and Fix modular switch 1 way 6 amp.1 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

Supply and Fix modular switch 1 way 16 amp.1 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

Supply and Fix modular Socket, 6A - 2/3 pin combined 2 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

Supply and Fix modular switch 1 way 16 amp.2 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

Supply and Fix modular bell push 6 A, 1 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

Supply and Fix modular white cover plate with frame,1 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

Supply and Fix modular white cover plate with frame,3 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

Supply and Fix modular white cover plate with frame,6 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

Supply and Fix modular white cover plate with frame,8 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

S&F metal flush box 1/2 module complete all as specified and as directed.

S&F metal flush box 3 module complete all as specified and as directed.

S&F metal flush box 6 module complete all as specified and as directed.

S&F metal flush box 8 module complete all as specified and as directed.

S&F Bell buzzer, AC, 230 volts, single pole, Ding Dong. Make : Anchor/ Cona/ Plaza

S&F electronic modular fan regulator 230 volts, step type socket type, hum free 120 watt 2 Module complete all as specified and as directed

Supply and fix metal clad switch socket single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20A concealed in walls. Make : Legrand or equivalent of Schnieder (Multi -9) or Siemens/L&T (Hegar).

S&F ceiling rose, surface type Bakelite 65x55mm 3 terminal complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 18W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make : Philips/ Wipro/ Bajaj. Notes:- The contractor shall submit warranty certificate from manufacturer for minimum 2 years

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make : Philips/ Wipro/ Bajaj. Notes:- The contractor shall submit warranty certificate from manufacturer for minimum 2 years

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. Make : Philips/ Wipro/ Bajaj. Notes:- The contractor shall submit warranty certificate from manufacturer for minimum 2 years

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five starrated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers etc complete all as specified and as directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m complete all as specified and as directed

S&F factory made powder coated distribution board VTPN, 4 way double door including bus bar, Neutral bar, standard DIN rail, earth bar complete all as specified and conforming to IS: 8623 & IP 43 complete all as specified and as directed. Make/Model : Cat no 5077 45 of Legrand or equivalent in Siemens/ Schnieder/L&T

S&F factory made powder coated distribution board SP & N 8 way, double door including bus bar, Neutral bar, standard DIN rail, earth bar complete all as specified and conforming to IS: 8623 all as specified. Make/Model : Siemens/ ABB/ Legrand

S&F Triple pole Neutral MCB 63 Amp , 415 v, 50 Hz AC suitable for ‘C’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 all as specified and as directed. Make/Model : Legrand Cat Part No 408683 or equivalent of Schnieder (Multi -9)/ L&T (Hegar).

S&F MCB SPN 32 Amp , 240 v, 50 Hz AC suitable for ‘C’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 all as specified Make/Model :- Legrand Cat Part No 408617 or equivalent. of Schniede, Siemens.

Supply and fixing single pole MCB 6 to 32 Amps, 240 v, 50 Hz AC suitable for ‘C’ curve, 10 KA breaking capacity conforming to IS 8828 of 1996 complete all as specified and as directed Make/Model :- Legrand Cat Part No 408587 to 408595 or equivalent. of Schniede, Siemens.

M&L Sub main wiring for circuit complete with 2 runs of 6 sqmm single core PVC insulated, unsheathed FRLS 1100 Volt grade multi stranded copper conductor cable drawn through and including suitable size PVC Casing Capping / PVC rigid conduit and accessories complete fixed surface to wall/roof/ceiling etc and including 1 run of 6sqmm single core PVC insulated, unsheathed FRLS 1100v grade multi stranded copper conductor cable as earth continuity conductor etc complete all as specified and directed. Make:- Havells/ Polycab/ Plaza.

Note for item No 189 :- (a) 2 runs of 6 sqmm cable along with one run of 6 sqmm cable for earth conductor and PVC casing capping/PVC rigid conduit shall be measured as one length.

(b) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles.

M&L Sub main wiring for circuit complete with 2 runs of 4 sqmm single core PVC insulated, unsheathed FRLS 1100 Volt grade multi stranded copper conductor cable drawn through and including suitable size PVC Casing Capping / PVC rigid conduit and accessories complete fixed surface to wall/roof/ceiling etc and including 1 run of 4sqmm single core PVC insulated, unsheathed FRLS 1100v grade multi stranded copper conductor cable as earth continuity conductor etc complete all as specified and directed. Make:- Havells/ Polycab/ Plaza.

Note for item No 192 :- (a) 2 runs of 4 sqmm cable along with one run of 4 sqmm cable for earth conductor and PVC casing capping/PVC rigid conduit shall be measured as one length.

(b) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles.

Earthing with Galvanised Earth Plate Electrode 600x600x 6mm thick burried directly in Ground (Earth Pit not less than 2.25 Metre below Ground Level) with Top edge of the Plate not less than 1.50 Metre below Ground Level, connected with Galvanised Earth Strip of size 32 x 6mm by means of Bolts, Nuts, Check Nuts and Washers of GI or Steel and connected Earthing Testing Point/Bus-bar including GI 40mm bore (dia) light grade Protection Pipe, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt, magnesium sulphate (1 : 1 : 0.5) in alternate layers of not exc 150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50 mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, Funnel with GI Watering Pipe 20mm bore (dia) medium grade including necessary Excavation in in any type of Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on Completion including taking down existing one complete all as per specified and as directed by Engineer-in-Charge. NOTE : GI strip upto 7.5 Mtrs shall be included in quoted rates and beyond 7.5 mtrs shall be measured and paid separately.

Note for Item 195 :- (a) All Joints should be joined by Exothermic Welding or Brazing.

(b) After completion of work earthing shall be tested by the contractor in presence of Engineer-in-Charge, User and proper record shall be maintained.

(c) Earth resistance tester shall be provided by the contractor. It should be caliberated from authorised company/ lab.

(d) After testing if desired earth resistance of less than 5 Ohm is not obtained, the earthing will be redone at no extra cost to Govt till desired result is obtained.

M&L Sub main wiring for circuit complete with 2 runs of 1.5 sqmm single core PVC insulated, unsheathed FRLS 1100 Volt grade multi stranded copper conductor cable drawn through and including suitable size PVC Casing Capping / PVC rigid conduit and accessories complete fixed surface to wall/roof/ceiling etc and including 1 run of 1.5 sqmm single core PVC insulated, unsheathed FRLS 1100v grade multi stranded copper conductor cable as earth continuity conductor etc complete all as specified and directed. Make:- Havells/ Polycab/ Plaza.

Note for item No 200 :- (a) 2 runs of 1.5 sqmm cable along with one run of 1.5 sqmm cable for earth conductor and PVC casing capping/PVC rigid conduit shall be measured as one length.

(b) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles.

Supply and fix indicating indoor wall light 'RED and GREEN' with LED 230 V, including all accessories complete all as specified and directed. Make:- Luker Cat No LWL 122-2 or equivalent in Philips /Havells/Wipro

Supply and fix Water heater with storage type, vertical, electric single phase 240 V, 2 KW heating element, Capacity 25 ltrs, BEE 5 star rated complete all as specified and directed. Make- Havells, Model No. Monza DX Cat part No. GHWAMGTWH025 white colour or Recold, Bajaj. Note :- (a) The Contractor shall given a written guarantee of minimum two years from completion of work.

M&L Stop valves, fancy type, chromium plated cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 20mm bore of iron pipe or for union complete all as specified and directed.

M & L 20 mm bore fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

M & L for making connection of PP-R distribution branch with PP-R main of 16 to 40mm outer dia by providing and fixing tee including cutting and making fusion joint etc

S&F 25 mm outer dia of pipes 3-layer PP-R (Polypropylene random copolymer) pipes concealed pipes SDR 7.4 (PN-16 @ 20oC) UV stablised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings, complete to walls, ceilings or in floors etc. all as specified and directed. Make : SFMC, KPT, Prince

Note for item No 208 :- (a) The unit rate shall include the cost of short lengths, with all pipe fittings such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc and fixing accssories such as pipe hooks, screws clamps etc

(b ) Wall thickness of pipes shall be all as per IS : 15801

S&F Wash basin vitrous china (flat back and angle back Type) size 580x400mm including taps waste chain and plug and porceline stopper but brackets including cutting for and pinning in ends of brackets or erecting stand with waste pipe complete all as specified and directed by Engr-in-charge.

S&F 32 mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer- In - charge

S&F 20 mm outer dia of pipes 3-layer PP-R (Polypropylene random copolymer) pipes concealed pipes SDR 7.4 (PN-16 @ 20oC) UV stablised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings, complete to walls, ceilings or in floors etc. all as specified and directed. Make : SFMC, KPT, Prince

Note for item No 213 :- (a) The unit rate shall include the cost of short lengths, with all pipe fittings such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc and fixing accssories such as pipe hooks, screws clamps etc

(b ) Wall thickness of pipes shall be all as per IS : 15801

S&F 32mm bore low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sqcm for WHB complete all as specified and as directed.

M&L Stop valves, fancy type, chromium plated cast copper alloy screwed down, with long shank and cup (concealed type) high pressure, with crutch or butterfly handle, screwed both ends for 20mm bore of iron pipe or for union complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 600 mm including complete all as manufactures and all as specified and directed by Engineer- In - charge.

S&F PVC (SWR) pipes single socket in any length with rubber ring joints of 75 mm bore fixed to wall complete all as specified and as directed by Engineer-in-Charge

M & L 15 mm bore fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F PVC (SWR) floor trap 75mm dia of outlet pipe, plain with grating including jointing with solvent cement complete all as specified and as directed.

M&L Reinforced cement concrete (nominal mix) 1:2:4, Type B–0 using 12.5mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and as directed.

M & L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. rough finished flat surfaces of concrete complete all as specified and as directed.

M&L for form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide for rough finished surfaces of concrete complete all as specified and as directed.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep in soft/loose soil complete all as specified and as directed.

M&L 100 mm thick Plain cement concrete 1:2:4 type B-2 (using 40 mm graded stone aggregate ) as in sub base to receive floor tiles, complete all as specified and directed.

M&L Virified Ceramic tiles 10 mm thick, light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertcal surfaces such as skirting/ dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer ,15 mm thick in Cement Mortar 1:6 complete all as specified and as directed.

M&L Vitrified Ceramic tiles 10 mm thick, light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in skirting/dado. etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including backing coat ,10 mm thick in Cement Mortar 1:4 complete all as specified and as directed.

Note for item No 227 & 228 :- (a) Vitrified tiles are classified under group B1a of the international Standard for ceramic tiles ISO: 13006. Tiles shall be hard, dense, impervious and frost resistant. Water absorption of tiles shall be less than 0.5% and flexural strength (Modulus of Rupture) shall be more than 35 N/Sqmm.

(b) The manufacturer's test certificate for tiles must be submitted for approval by the concerned authority.

M&L chequered cement concrete tiles 30cm x 30cm x 25mm thick machine pressed set jointed and pointed in neat cement slurry as in treads and cut and polished using mixture of white & grey cement in equal proportions & pigment, over screed bed or bedding layer of mortar 15mm thick for laying floor fnishes in cement mortar (1:4) complete all as specified and as directed by Engineer-in Charge.

M&L Machine pressed rubber moulded precast concrete interlocking paver block with grey cement and pigment any shape and size, polished confirming to IS-15658 of 60mm thickness M-35 grade, laid over and including M sand cushion of 50mm thick complete and packing the sides with PCC 1:3:6 type C1 using 20 mm graded stone aggregates all as specified and directed. .

Note for item No 232:- (a) The Unit rate quoted is included for Demolition of Stone Slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar

(b) The manufacturer's test certificate and individual test certificate of Tiles must be submitted for approval by the concerned authority prior to procurement.

KUMAR AGENCIES

jk construction

KSR AND COMPANY

Neptune Engineers and Builders

eurekaenterprises

G Perumal and co

s v m construction building & engineers