Construction at ACSTI

Civil - Hostel Block

Cleaning removal of Heavy Jungle clearing the debris away from the site including cost of required tools and plant and necessary etc., all complete in all respect and as directed by the departmental officers. (W-0001)

Bored cast in situ piles Installation of vertical cast in situ bored piles of following dia using design mix of grade M 40 concrete (using hard broken stone graded chips of size 20mm and less) by setting the bored cast in situ pile equipments with all acccessories and tools at each of locations based on the sequence of operations as directed by the Engineer-in-charge, boring for the piles from ground level in all soils to the required depth below cut off level to carry a safe working load not less than specified using transit bore mud circulation method (using bentenite clay of required density) inclusive of pile driving accessories, temporary casing pipe, bentonite solution of 10% of concrete with required specific density, mobilisation, transferring, installation of pile driving accessories from one location to another, removal of mud from site upto a distance of 5km as directed by the departmental officers, the cost of shoe and length of pile to be embedded in the pile cap but excluding cost of steel and fabrication of reinforcement grills etc., complete complying with relevant standard specifications and as directed by the departmental officers. [The length of pile shall be measured from the top of shoe to the bottom of pile cap].

500mm dia

600mm dia

Chipping of RCC pile head of following dia pile to the required cut off level and clearing away the debris from site with an average lead of 5km etc., complete complying with relevant standard specifications and as directed by the departmental officers.

500mm dia

600mm dia

Mobilisation charges inclusive of transportation to site assembling and dismantling the rotary pile equipment employed for the works etc., complete complying with relevant standard specifications and as directed by the departmental officers. (Qtn)

Conducting Routine load test for bored cast in situ RCC piles of following dia by direct loading in accordance with IS 2911 ( part IV) 1985 excluding cost of pile and dismantling the same after testing, including finishing pile head and supplying and erection of all kentledge of suitable magnitude as specified, labour, excavation, back filling compaction etc., complete complying with relevant standard specifications and as directed by the departmental officers (150% of pile capacity) (Qtn)

600mm dia pile - Initial Testing Pile

600mm dia pile - Vertical Test

500mm dia pile - Initial Testing Pile

500mm dia pile - Vertical Test

Earth work excavation for foundation in all soils and sub-soils to the required depth as may be directed except in hard rock requiring blasting but inclusive of shoring, strutting, and bailing out water wherever necessary and refilling the sides of foundation with excavated earth in 150mm thick layers well watered rammed and consolidated and depositing the surplus earth in places shown clearing and levelling the site with an initial lead of 10 metres and lift as specified here under etc. complete in all respects complying with relevant standard specifications. (Including Refilling)

Supply and filling in foundation and basement with Stone dust in layers of 150mm thickness well watered, rammed and consolidated complying with relevant standard specification including cost of stone dust etc., all complete and as directed by departmental officer.

Plain cement concrete 1:4:8 (One of cement, four of sand and eight of hard broken stone jelly) for foundation using 40mm gauge hard broken stone jelly inclusive of shoring, strutting and bailing out water wherever necessary ramming, curing etc., complete in all respects complying with relevant standard specifications and as directed by the Departmental officers.

Flooring with a bed of CC 1:5:10 (one of cement, five of sand and ten of hard broken stone jelly) using 40mm size hard broken stone jelly and top left rough to receive the floor finish with required slopes including ramming, curing etc., all complete complying with relevant standard specifications.

Filling in foundation and basement and other similar works with Excavated earth in layers of 150mm thick well watered rammed and consolidated complying with relevant standard specification etc., all complete and as directed by the departmental officers.

Supply and filling the low lying area for the proposed formation of approch road with gravel in layers of 150mm thickness well watered, rammed and consolidated complying with relevant standard specification including cost of gravel etc., all complete and as directed by departmental officer.

Providing and Laying in position, Standardised concrete mix M-25 grade in accordance with is: 456 - 2000 using 20 mm and downgraded hard broken stone jelly for all rcc works namely column, column footings, plinth beam, grade beam, raft beam, raft slab etc., with minimum cement content of 350 kg/m3 and maximum water cement ratio of 0.50, including admixture (plasticiser/super plasticiser) in recommended proportions as per is :9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m) 7730 kg. of 20 mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10 -12 mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand for making 10m3 concrete but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing etc., complete complying with standard specification and as directed by the departmental officers. the coarse and fine aggregates to be used should comply with the requirements of is standards. (no separate payment will be made by the department for the excess usage of materials)

Foundation and basement

Ground Floor

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Providing and laying in position, Standardised concrete mix M-30 grade in accordance with is: 456 - 2000 using 20 mm and downgraded hard broken stone jelly for all rcc items of works namely tee, ell or rectangular beams, lintel, parapet cum drops, waist and landing slab, canophy, circular column, fin projections, sunshades, window boxing slab, slab and other similar works with minimum cement content of 400 kg/m3 and maximum water

Foundation and basement

Ground Floor

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Supplying, fabricating and placing in position of Mild steel Grills / Ribbed Tor Steels of all diameters for reinforcement for all floors including cost of binding wire, bending tying etc., all complete and as directed by the departmental officers.

Applying one coat of anticorrosive treatment on steel reinforcement rods (20 ltrs. Of anitcorrosive chemical for one mertic tonne of steel reinforcement rods) at site including a cost of required quantity of anticorrosive chemicals, (best approved quality) cement, consumables such as brushes, gloves and labour for anticorrosive coating etc. complete and as directed by the departmental officers. (The Quantity and brand of anticorrosive chemaical should be got approved by the EE before use).

Providing Form work and centering for reinforced cement concrete works including supports and strutting up to 3.30m height for plane surfaces as detailed below with all cross bracings using mild steel sheets of size 90cm x 60cm and MS 10 gauge stiffened with welded mild steel angles of size 25mmx25mmx3mm for boarding laid over silver oak or country wood joists of size 10cmx6.5cm spaced at about 90cm centre to centre and supported by casurina props 10cm to 13cm dia spaced at 75cm intervals and removing the same after a specified period without damaging the R.C.C works etc., complete complying with standard specifaction and as directed by the departmental officers.

Column footings,plinth beam,Grade beam, Raftbeam,Raft slab etc.,

Plain surfaces such as Roof slab, floorslab, Beams, lintels, lofts, sillslab, staircase waist, portico slab and other similar works

Square and rectangular columns and small quantities such as sunshade, parapet cum drops window boxiing, fin projection and other similar works.

vertical walls

Brick work in CM 1:5 (One of cement and five of sand) using chamber burnt bricks of size 9”x4½”x3” (23x11.4x7.5 cm) in foundation and basement including dewatering wherever necessary proper setting, curing etc., complete with relevant standard specifications.

Brick work in Cement Mortar 1:6 (One of cement and six of sand) using Chamber burnt bricks of size 9”x4½X3” (23x11.4x7.5cm) for super structure in the following floors including labour for fixing the doors, windows and ventilator frames in position, fixing of hold fasts, scaffoldings, curing etc., complete in all respect complying with relevant standard specifications and drawings.

Ground Floor

First Floor

Second Floor

Third Floor

Fourth Floor

Autoclaved Aerated Concrete block masonry: Supplying and constructing of Autoclaved Aerated Concrete (AAC) block masonry using blocks having dimesions of 600 x 200mm and thickness 100mm to 300mm of density of 600 Kg/m3 with compressive strength not less than 3 N /mm2 conforming to IS 2185 (part III) 1985 from FFL till structural ceiling level or height as mentioned in drawing in cement mortar 1:6 (One of Cement and six of sand) for super structure in the following floors if required suitable plasticizer may also be added. The horizontal and vertical joint thickness should be approximately 10mm. Masonry works strictly be carried out as per IS 6041 - 1985 (Reaffirmed 1990). The same shall be anchored properly with the structure. The work should be carried out as per the instruction of departmental officers. The rate including cost of form work, scaffolding, racking out joints, including materials, labour, tools, equipments all lead, lifts necessary finishing, curing etc., all complete complying with relevant standard specification. The quality and brand should be got approved from Executive Engineer before use).

Ground Floor

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Autoclaved Aerated 100mm Thick Block Masonry: Supplying & constructing of Autoclaved Aerated Concrete (AAC) block masonry using blocks having dimensions of 600 x 200mm and thickness 100 mm of density 600 Kg / m³ with compressive strength not less than 3 N/mm² conforming to IS 2185 (part III) 1985 from FFL till structural ceiling lvl or height as mentioned in drawing in cement sand mortar 1:4 (One of Cement and four of sand), if required suitable plasticizer may also be added. The horizontal and vertical joint thickness should be approximately 10 mm. Masonry works strictly be carried out as per IS 6041 - 1985 (Reaffirmed 1990).

Ground Floor

First Floor

Second Floor

Third Floor

Fourth Floor

Special ceiling plastering in cement mortar 1:3 (One of cement and three of sand) 10mm thick for bottom of roof, stair, waist, landing and sunshades in all floors finished with neat cement including hacking the areas, providing band cornice, scaffolding, curing etc., complete

Plastering with CM 1:5 (One of cement and five of sand) 12mm thick finished with neat cement including providing band cornice, ceiling cornice, curing, scaffolding, etc., complete in all respects and complying with relevant standard specifications.

Plastering with CM 1:5 (One of cement and five of sand) 20mm thick finished with neat cement including providing band cornice, ceiling cornice, curing, scaffolding, etc., complete in all respects and complying with relevant standard specifications.

Plastering with cm 1:3 (one of cement and three of sand ) 12 mm thick mixed with water proofing compound (CICO) at the rate of 2 kg / 10 sq.m including curing etc., all complete complying with relevant standard specification.

Providing pre-constructional Antitermite treatment including cost of chemicals labour as per standard specifications for preparing the area for treatment by spraying chemicals and other incidental charges etc.. complete. The rates should be for curing antitermite treatment from the plinth beam and brick masonry with super structure in contact with the back fill earth and at the junction on the walls. The top surface of filled earth for flooring and the soil along with the perimeter of the building by making holes with the crow bar and poured 5% termicide. “Chloripyrifos” and spraying the same termicide solution on the wooden frames and treating he other periphery of buildings etc., complete in all respects as per IS 6313 (part II)/ 1981 and as directed by the departmental officers.

Supplying and fixing of Teak Wood wrought and put up for frames of doors, windows, ventilators, cupboard and any other similar joineries works with necessary plugs, rebates for shutters, plaster grooves on all faces etc. , including labour charges for fixing hold fasts, complying with relevant standard specifications etc., in all respects.

Teak wood over 2.00 metre and below 3 metre length

Teak wood below 2.00 metre length

Supplying and fixing of single leaf Soild core flush door shutters with using boiled water resistance (BWR) teak wood ply as per IS 303-1989, the cross band and face veneers are to be banded with phenol formaldehyde synthetic resin in hot press both sides and manufacturing the shutter by using quality timber of termite proof and seasoned to moisture content not more than 10%, hot pressed with hydraulic press at a temperature of 150o to the norms as per IS 2002-1983 and TW Ply on one side with teak wook lipping around, 35mm thick including cost and fixing of Brass furniture fittings such as 3 nos 5” hinges, 2 Nos 6" Brass Towerbolt, 2 Nos 6" Brass Handle, 1 no Mortice lock with required screws with 3 keys with night latch, 1No 40mm dia & 60mm long rubber bush ,1 no Aluminium Door stopper with rubber bush with required Brass screws, labour charges for wrought and putup and fixing in position of flush shutters and painting the TW portion with two coats using 1st class synthetic enamel paint over one coat of primer and as directed by the departmental officers. (The quality and brand of materials should be got approved from the Executive Engineer before use.)

1500x2100mm (Two Leaves)

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work. (M-0674)

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work. (M-0675)

Supplying and fixing Mild Steel grills as per the design approved to verandah enclosure or gate including one coat of primer and labour for fixing in position etc. all complete

Supplying and applying of Full putty two coats with aprroved make wall putty for smooth finishing the new cement plastered walls including cost of putty, brushes, watering curing labour charges for apply putty, blade etc., complete as directed by the departmental officers. (The quality and brand should be got approved from the EE before use.)

Painting the false ceilling / walls two coats with 1st class ready mixed Interior emulsion paint of best approved quality colour and shade over a priming coat, including clean removal of dirt and dust etc., complete including cost of necessary brushes, labour charges, putty etc., complying with relevant standard specification. (The paint should be supplied by the contractors at his own cost.The quality and shade of the paint should be got approved by the Executive engineer before use.) (Inner)

Painting the false ceilling / walls two coats with 1st class ready mixed Exterior emulsion paint of best approved quality colour and shade over a priming coat, including clean removal of dirt and dust etc., complete including cost of necessary brushes, labour charges, putty etc., complying with relevant standard specification. (The paint should be supplied by the contractors at his own cost.The quality and shade of the paint should be got approved by the Executive engineer before use.) (Outer)

Supplying and fixing of Double charges Vitrified Tiles of size 59.5x59.5cmx10mm for flooring and other similar works (Best approved quality, colour and shade and the same shall be got approved from the Executive Engineer before use) in cement mortar 1:3 (one of cement and two of sand) 20mm thick including fixing in position, cutting the tiles to the required size wherever necessary pointing the joints with grout (Tile joint filler), curing, finishing etc., all complete and as directed by the departmental officers.

Supplying and fixing of Ruby Red colour Granite slab super fine polished with machine cut edges of 18 to 20 mm thick for flooring (Best approved quality and the same shall be got approved from the Executive Engineer before using) over cement plastering in CM 1:3 (One of cement and three of sand) 20mm thick including fixing in position, cutting the tiles to the required size wherever necessary, pointing the joints with coloured cement, curing, finishing etc., all complete and as directed by the departmental officers.

Providing Single nosing to the edges of Granite slab of 20 mm thick including labour, power consumption, tools & plants required, true to horizontal etc., for Kitchen platform in all floors and as directed by the departmental officers.

Providing Grooving the Granite slab including cost of all labour charges etc., all complete and as directed by the departmental officers.

Supplying and fixing of Ceramic Tiles Anti skid without corrugated design for flooring and other similar works (Best approved quality, colour and shade shall be got approved from the Executive Engineer before using) over cement mortor 1:3 (One of cement and three of sand) 20mm thick including fixing in position, cutting the tiles to the required size wherever necessary, pointing the joints with Grout (Tile joint filler), curing, finishing etc., all complete and as directed by the departmental officers

Providing and filling the tile joint with epoxy grout with following specification: Surface preparation including cleaning the joint to be free from dust and loose particles. Providing masking tape on either side of the tile joint edges and providing sealing the tile gap with epoxy tile joint grout and finishing neatly and as directed by the departmental officers. The rate inclusive of cost of materials and labour, etc., complete. (M-0227)

Supplying and fixing of Colour glazed tiles (Best approved quality and the same shall be got approved from the Executive Engineer before using) over cement plastering in CM 1:2 (One of cement and two of sand) 10mm thick including fixing in position, cutting the tiles to the required size wherever necessary, pointing the joints with coloured cement, curing, finishing etc., all complete and as directed by the departmental officers.

Finishing top of roof with one course of Hydraulic Pressed Tiles of approved superior quality of size 23cmx 23cmx20mm thick laid over weathering course in cm 1:3 (One of cement and three of sand) 12mm thick mixed with Water proofing compound at 2% by weight of cement used and pointed neatly with the same cement mortar mixed with water proofing compound including curing etc., as per standard specifications. (The quality of tiles shall be got approved from the EE before use)

Weathering Course with concrete broken brick jelly 20mm gauge in pure burnt lime stone slaked and screened (No Sand) over RCC Roof Slab with proportion of brick jelly to lime (fat lime) being 32: 12 1/2 by volume well beaten with wooden beaters for giving the required slope and thickness complying with relevant standard specification and as directed by the departmental officers.

Providing Granite Tile of 10mm thick, wall cladding 1:3 (one of cement and three of sand ) 12 mm thick including finishing and fixing in position complying with relevant Standard specifications etc., complete in the following floors (Measurement will be taken including bearing also) as directed by the departmental officers (Quality of Granite slab shall be got approved by the Executive Engineer before fixing.

Supplying and laying of Designer Interlocking Paver blocks 63mm thick to take the load of 40N/sqmm, including water, electricity, leveling the ground and consolided earth etc., all complete and as directed by the departmental officers. (The Brand quality of materials should be got approved from EE before use)

Supplying and fixing stainless steel hand railing 304 grade with top railing tube of 50mm 304 grade with top railing tube of 50mm dia of 12 gauge and 2.5mm wall thickness, vertical tube of 40mm dia of 14 gauge and 2mm wall thickness with 900mm clear weight at requied intervals with 2 lines of horizental tube of 25mm dia of 16 gauge and 1.6 mm wall thickness, 62.5mm dia front post ball set and restical base cub of 16 gauge and wall thickness of 1.6mm including polishing, buffing, fabrication and erection in the places shown by the departmetnal officers and embeded in the places with PCC 1:2:4 using 20mm stone jelly making holes and redoing the same and labour charges, power consumption charges etc., all complete complying with relevant standard specifications and as directed by the departmental officers. (M-0651)

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete (M-0652)

Painting the new wood work with two coats of approved first class synthetic enamel ready mixed paint in addition to one coat of primer of approved quality and shade, the paint should be supplied by the contractor at his own cost (The quality and the shade of paint should be got approved by the Executive Engineer before use) complying with relevant standard specifications.

Painting the new Iron work and other similar works such as PVC /ASTM Pipes, Kerb Stone and grills with two coats of approved first class synthetic enamel ready mixed paint of approved quality and brand, the paint should be supplied by the contractor at his own cost. (The quality and the brand of paint should be got approved by the Executive Engineer before use) complying with relevant Standard specifications.

Construction of Inspection chamber size 60 x 60 x 75 cmwith brickjelly cement concrete 1:3:16 ( One of cement, eight of sand and sixteen of broken brick jelly 40mm gauge 15cm, thick for foundation and 23cm thick brick mansonry in c.m 1:6 using stock bricks of size 9"x4 3/8"x2 3/4" and plastering with c.m 1:3 (one of cement, three of sand and four of hard broken stone 20mm gauge) 5cm thick precast cover slab excluding the cost and fabrication of reinforcement grills but including benching channelling fixing the cover slab in position curing, finishing etc., complete in all respects.

Supplying and fixing Hydraulic Door Closer of various sizes of approved quality using Aluminium Extruded Section Body Tubular Type Universal Hydraulic Door Closer with Double Speed Adjustment (with ISI Monogram) including labour charges for fixing etc., complete complying with relevant standard specifications. (The brand and quality of hydraulic door closure should be got approved from EE before use ) (M-0311)

Supplying, fabricating and fixing in position of Aluminium anodised natural colour matt finish of single leaf fully panelled sliding door with 12mm thick both side prelaminated particle board at the Shutter bottom rail:[email protected] kg/m,Top & Verticle 50x44.45x2.50mm @ 1.292 kg/m, Lock rail 50x44.45x2.50mm @ 1.292 g/m, Running channel section:[email protected] kg/m, and necessary accessories such as Alu.clips 17.15x17.27x1.50mm @ 0.176 kg, Alu handle 100x30mm @ 0.988 kg/mfull length of handles on both sides, lock, roller, including cost of materials, labour charges and power consumption charges required for fabrication including chipping, dismantling and waking hole to the required extent in RCC column, beam masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc. complete. All the Alu. sections are to be anodised. with matt finish under electrically controlled condition in accordance with IS 1868/1962 for an average anodic film thickness of 15 microns etc

Supplying and Fixing MS Ladder width 45cm using 50x50x6mm MS Angle labour for fixing etc., all complete as directed by the departmental officers

Providing Rain water harvesting pit by augering 300mm dia bore pits to a depth of 5.50m overall depth and filling with stone jelly of 40mm size including earth work excavation 1m dia, 600mm depth and filling with filling sand to a depth of 300mm filling sand over the stone jelly and covered with Pre-cast RCC Perforated slab of 40mm thick excluding the cost and fabrication of reinforcement grills but including precasting, moulding, curing, finishing and fixing in position etc and all complete as directed by the departmental officer.

Providing pit

Augering 30cm dia

Supply, installation and fixing of dynamic façade using 10” × 5” split weathering tiles, repurposed from conventional terrace flooring application, mounted within custom-fabricated mild steel / galvanized steel frames, complete. The tiles shall be loosely supported and not rigidly fixed, permitting controlled movement under wind pressure to achieve a passive dynamic façade effect, without use of any mechanical or motorized system. The item shall include design, fabrication, erection, alignment, and anchoring of supporting metal framework, including all brackets, clamps, bolts, nuts, washers, and corrosion-protection treatment, complete as per approved drawings and directions of the Engineer-in-Charge. Rate shall include all materials, labour, tools, tackles, scaffolding, leads, lifts, and incidentals, complete in all respects.

PLUMBING

Supplying and fixing the following dia PVC (SWR) pipe and relevant specials including packing the joints with rubber lubricant fixing them into walls with necessary wooden plug screws, holding wherever necessary and making good of the dismantled portion with necessary connections to sanitary fittings etc., complete in all respects as directed by the departmental officers.

110mm dia PVC SWR pipe including all required PVC specials etc., all complete.,

75mm dia PVC SWR pipe including all required PVC specials etc., all complete.,

Supplying, laying, fixing and jointing the following PVC pipes as per ASTM D - 1785 of schedule 40 of wall thickness not less than the specified in IS 4985 suitable for plumbing by threading of wall thickness including the cost of suitable PVC/GI specials /GM specials like Elbow, Tee reducers, Plug , unions, bend, coupler, nipple/ GM gate valve, check and wheel valve etc., wherever required above the ground level including the cost of teflon tapeetc., Fully concealed in walls to the proper gradient and Alignment and redoing the Chipped portion of Masonry etc.,all complete and as directed by the departmental officers. 50mm ASTM (D schedule 40 threaded) PVC pipe with necessary PVC/GI specials

Supplying and fixing 150mm x 100mm size stone ware Gully trap with iron gratings over a bed of 150mm thick brick jelly concrete in CC 1:8:16 (one of cement, eight of sand and sixteen of broken brick jelly) using 40mm size brick jelly and brick masonry wall 114 mm thick using chamber burnt bricks of size 9”x4-1/2”x3” (23x11.4x7.5cm) in cm 1:5 (One of cement and five of sand ) plastered with CM 1:3 (One of cement and three of sand) 12mm thick etc., complete and as directed by the departmental officers.

Supplying and fixing of PVC Nahani Trap not less than 75mm 4 way / 2 way (Superior variety) having minimum of water seal of 50mm confirm to relevant I.S. specifications with its latest amendments including resting on the bed of brick jelly resting on the bed of brick jelly concrete 1:5:10 (One of cement, five of sand of ten of 40 mm gauge brick jelly) etc., complete as directed by the departmental officers (The PVC Nahani Trap should be got approved from the EE before use)

Supplying and fixing EWC superior variety (White) 500mm including cost and fixing of double flapped coloured plastic sheet cover, PVC flushing cistern in appropriate level as directed by the departmental officers at a maximum level of 5’6” and of approved brand of 10 litres capacity including fittings such as CI brackets. PVC connection, GM wheel valve, Hex Nipple, etc., complete (Brand, colour of EWC and plastic cover shall be got approved from the Executive Engineer before fixing)

Supplying and fixing of 110mm dia PVC SWR pipe for Rain water down fall pipe with necessary gratings, shoes, bends, off sets, clamps, teak woods plugs, and of approved quality and including fixing C.I. gratings at the junction of parapet and floor or roof slab etc., including finishing etc., complete complying with relevant standard specifications.

Supply and delivery of 110mm dia UPVC - Non Pressure Pipes as per IS 15328/2003,SN8- SDR 34 with excise duty suitable for plumbing by threading of wall thickness fixing on wall to the proper gradient and alignment and redoing the chipped of masonry etc., complete complying with relevant standard specifications and as directed by the departmental officers. (The pipe quality and brand should be got approved from the EE before use ).

Supplying and fixing of porcelain wash basin superior variety of size 22”x16” (550x400mm) including cost and fixing of CI brackets, pvc waste pipe required grating, cp tap, wheel valve/ Bob cork, pvc, connection, cp waste plug, with aluminium chain etc., complete in all respects (washbasin shall be got approved by the Executive Engineer before fixing)

Supplying, laying, fixing and jointing the following PVC pipes as per ASTM D - 1785 of schedule 40 of wall thickness not less than the specified in IS 4985 suitable for plumbing by threading of wall thickness including the cost of suitable PVC/GI specials /GM specials like Elbow, Tee reducers, Plug , unions, bend, coupler, nipple/ GM gate valve, check and wheel valve etc., wherever required above the ground level including the cost of teflon tapeetc., Fully concealed in walls to the proper gradient and Alignment and redoing the Chipped portion of Masonry etc.,all complete and as directed by the departmental officers.

50mm dia Astm D schedule 40 threaded Pvc pipe with necessary PVC/GI specials

32mm dia Astm D schedule 40 threaded Pvc pipe with necessary PVC/GI specials

25mm dia Astm D schedule 40 threaded Pvc pipe with necessary PVC/GI specials

Supplying and fixing, Brass body nickel plated with stainless steel ball, lever operated Ball Valve, fixing to pipe work with required fixing materials, testing, etc., complete.

Using 25mm dia Ball Valve.

Using 32mm dia Ball Valve.

Using 40mm dia Ball Valve.

Using 50mm dia Ball Valve.

Supplying, laying, fixing and jointing the following PVC pipes as per ASTM D - 1785 of schedule 40 of wall thickness not less than the specified in IS 4985 suitable for plumbing by threading of wall thickness including the cost of suitable PVC/GI specials /GM specials like Elbow, Tee reducers, Plug , unions, bend, coupler, nipple/ GM gate valve, check and wheel valve etc., wherever required above the ground level including the cost of teflon tapeetc., Fully concealed in walls to the proper gradient and Alignment and redoing the Chipped portion of Masonry etc.,all complete and as directed by the departmental officers. 20mm ASTM (D schedule 40 threaded) PVC pipe with necessary PVC/GI specials

Supplying and fixing, CPVC pipes (sdr 11.5 grade) and pipe specials like Coupler, reducer, elbow, tee and brass male/ female threaded pipe specials to connect bath room fittings, union, by pass bend with all type of Special flanges and special fittings to connect with de-similar materials like G.I or any other material, cutting the pipes, fixing the pipe specials using solvent cement solution supplied by the same manufacturer, making water tight joints, making holes and cutting grooves in walls restoring the damaged portions to their original condition using required materials, conducting hydraulic test to pipe work to a pressure of 7 Kg per Sq.cm, etc. complete and as directed by the site engineer. (Please note that the mentioned diameters are ID.) For filtered water supply

Supplying and fixing of CP Shower Arm with Overhead Shower Rose of best approved quality with necessary ISI mark (shower rose shall be got approved from the E.E. before fixing) etc. complete complying with relevant standard specifications and as directed by the departmental officers. (M-0516)

Supplying and fixing of CP Wall Mixture Tap 3 in 1 system with Hand Showers of best approved quality with necessary ISI mark (Material shall be got approved from the E.E. before fixing) etc. complete complying with relevant standard specifications and as directed by the departmental officers. (M-0514)

Supply & Fixing of Bevelled edge mirror of approved quality and brand of size 500 x 400 x 5.5mm shelf type mounted in the PVC / Fibre Glass framed with necessary hard board backing including labour for fixing in position etc., complete and as directed by the departmental officers.

Supplying and fixing of Stainless Steel Health Faucet approved quality with ISI mark ( Health facet shall be got approved from the E.E. before use.) including all accessories etc. complete complying with relevant standard specifications and as directed by the departmental officers. (M-0656)

Installation, Testing & commissioning of Booster pump with tanks, comprising of 2 pumps (1 working + 1 standby) Centrifugal , non self priming, multistage type , fitted with standard motor, impeller and with priming facilities and other vital parts of the pump ,pressure vessel, high quality control panel comprising of change over dry run protection, DOL starter, suction and discharge manifolds, isolation valves, NRV with strainer, pressure gauges and pressure switches, control panel,Inclusive of Power wiring from the panel to motor termination etc., complete.

2.8 Lps at 22 M head.(DWS Booster Pump) (1 no. of working + 1 no. standby = 1 set)

Installation, Testing & commissioning of approved make submersible Clearwater lifting pump set with suitable horse power motor to each pump to discharge with control panel & all necessary accessories, conducting trail run, providing necessary civil foundations and base frame with all accessories like pressure gauge, control valve etc., and consumables, maintaining the system for the period of one year. Rate shall include all Electrical panel work connected to existing Electrical cable arrangement, etc. complete. Incoming Electrical cable to starter panel will be under scope of Electrical work. Transfer of water from UG Sump to Over Head Water Tank.

Flow : 1.2 lps Head :16-20 MWC No. of pumps : 2 (1 working + 1 Standby) Type : Submersible Application : Clear water transfer Time : 0.50 Hours

Constructing Masonry Chamber with internal size of 900 x 1200mm and up to 1500mm deep including necessary earth work excavation, laying 150mm thick 1:3:6 mix concrete using 40mm stone jelly in foundation, 230mm wide Brick work CM 1:5 mix, plaster interior and exterior with CM 1:4 for 15mm thick, providing 600 x 600mm size manhole cover & frame of medium duty, providing R.C.C roof slab over chamber in 1:1.5:3 mix with suitable reinforcement, providing and removing of wooden form work, refilling the sides with excavated earth, disposing off the surplus earth within the site, etc complete and as directed by the site Engineer.

Supply and fixing, chromium plated Towel rail 600mm long and 20m dia with cp brackets fixing in position using suitable C.P. screws, peak wood plugs etc., complete.

Supply and fixing, Soap dispenser with 500ml liquid soap, fixing the same over wall dado using required fixing materials,etc.,complete.

Supply and fixing, Paper Roll holder with flap, fixing the same over wall dado using required fixing materials etc.,complete.

Supply and fixing Following chromium plated bath room fittings of connecting to water pipe using teflon tape over threaded portions, Including supplying and fixing CP Nipples to connect the water supply pipe to CP fittings, testing for leak proof,etc complete.

Supply and fixing, Long Neck Pillar cock with aerator.

Supply and fixing, 15mm dia 2 way bibcock with wall flange.

Supply and fixing, 15mm dia Angle valve stop cock long inlet threads with wall flange.

Supply and fixing, 32mm dia Bottle trap with extension piece & connecting Hose.

Supply and fixing heavy quality 32mm dia waste coupling with dome grating

ELECTRICAL

LT CABLES & TERMINATIONS

Supply, Laying, Testing and Commissioning of stranded XLPE/PVC insulated, FRLS Armoured/Unarmoured/Flexible, Aluminium/Copper conductor, laid over Galvanized or MS supports/in excavated Trench/in duct/fixing on walls including Galvanized clamping support to the cable as per approved installation dwg. Circuit identification tag made of stainless steel should be attached with the concerned cable alongwith the test report of following sizes of cable to be submitted by the contractor at the time of delivery of material at site , Refer Indian standard, Specification: IS 1554, 7098, 5831, 3975, 694(Earthing cables), Installation: IS1255 & IS732, Multicore/Single core Armoured/Un-armoured cable, Insulation: As specified below, Inner sheath: Extruded PVC only for Multicore, Outer sheath: Extruded Type ST2 PVC, PVC Cable shall be a tough outer sheathing of PVC FRLS insulating material in standard colours., Voltage grade:1100Volts, Armoure: Galvanized Steel strip/Wire for multicore, Non Magnetic Aluminum Wire/Strip for Single core

Power Cables(Aluminum cables)

3.5C x 120 Sq.mm XLPE AR Al

3.5C x 35 Sq.mm XLPE AR Al

4C x 16 Sq.mm XLPE AR Al

LT CABLE TERMINATION

Supply, Installation, Testing and Commissioning of Compression type cable gland, Aluminium sockets for Aluminium cables / copper sockets for copper cables, insulation tape, anti corrosive paste, brass clamps for gland earthing with 14 SWG copper wire to connect to nearest earth flat., Refer Standard: IS 12943 for single compression, BS 6121 for Double compression(NA), Gland type : Brass with nickel plated (Double compression), Compression : Double, Sealing Ring : Natural rubber for indoor, Neoprene for Outdoor , Wherever copper cable connect to GI strips, the lugs shall be tinned copper lugs fitted using shake proof assembly screws, washers and 'nylock' or similar nuts.

Power Cables(Aluminum cables)

3.5C x 120 Sq.mm XLPE AR Al

3.5C x 35 Sq.mm XLPE AR Al

4C x 16 Sq.mm XLPE AR Al

LT PANELS

Supply, Installation, Testing and Commissioning of Indoor type LT Switchboards, Floor mounting type, Bottom/Top entry. Refer enclosed SLD, Refer standard : IS 13947, 8623(part-1), Enclosure: Compartmentalized Single front CRCA, Doors:2mm Body:2mm Gland:3mm covers and partitions:1.6mm., UPS Panel shall be considered Aluminum Gland sheet with 3mm thick, IP class:IP44 for Indoor/IP65 with weather proof enclosure for outdoor, Bus bars: Electrolytic grade conductivity as per standard IS 5082, Bus bar Material: As per SLD. All copper bus bar should be tinned., Bus bar suppotrs: DMC/FRP/SMC, Bus bar joints: Shrouded/Tinned , Protection releases: As specified, Ics=Icu for all breakers, Utilization category: All MCCB/ACB's shall be Cat: A except ACB's for Ltg & raw power input distribution panel shall be with Cat: B ., Louvers:Busbar chamber shall have louvers with fine mesh inside, Shade: Epoxy powder coated RAL 7032, Design: Modular Form 4B Type 6 for panel construction with common cable chambers. No live parts allowed in cable chambers., Cable entry: As per site condition, SPD should have N/O contact for remote indication with on lndication lamp, Bus bar insulation: The bus bar shall be covered with heat shrinkable FRLS PVC sleeves at all non contact points in colour of red, yellow, blue and black and the arranged in accordance with IS-5578, Note: 1) All the breakers shall have potential free aux NO/NC contacts for ON,OFF & TRIP Indications and BMS monitoring 2) All the breakers shall have spreaders/phase separators/RHOM/Pad lock/Door lock/trip free 3)Breakers shall have provision to add shunt trip

SUB PANEL-1

A) Incomer-1, 200 AMPS,TPN, TMD based MCCB with Manual closing Mechanism of 25 KA Short Circuit Rating with O/L and S/C Protection, Earth fault and Neutral current protection.with shunt coil & Earth fault Relay with CBCT., B) Indication & Metering:, 1 Sets of R,Y,B phase indicating lights (LED-TYPE) controlled with control 6A MCB, 1Sets of 3 phase, 4 wire,200A/5A, Digital flush type Class-I accuracy multifunction meter with RS485 modbus connectivity. 1 No. 200A/5A, Class-I, 10VA burden moulded CT's., D) Busbar:, 200 A, TPN, 25KA AL Busbar Chamber for the entire length of the Panel as per specification , 50 KA SPD ( SPD shall be with potential free contact ) class B+C for three phase with suitable HRC fuse in the incomer & ON LED indication lamp-1No, E) Outgoings :, 125 Amps TPN TMD based MCCB with Manual Closing Mechanism of 25 kA Short Circuit Rating, with Thermal O/L and Magnetic S/C Protection -1 Nos, 80 Amps TPN TMD based MCCB with Manual Closing Mechanism of 25 kA Short Circuit Rating, with Thermal O/L and Magnetic S/C Protection -8 Nos, 63 Amps TPN TMD based MCCB with Manual Closing Mechanism of 25 kA Short Circuit Rating, with Thermal O/L and Magnetic S/C Protection -7 Nos, NOTE, CLIENT reserves to supply any listed items, the contractor shall install the same at quoted installation price, CLIENT reserves to change specification and makes of materials prior to procurement by contractor, All the execution shop drawings shall be prepared by vendor and approval shall be taken from Consultants/Architects/Client before execution, The sample of material used shall be provided by vendor as required for approval of Consultants/Architects/Client before procurement, Incase any item required for quality execution is not included in tender BOQ, the same can be added by vendors with information to consultants, architects & Client, If any items mentioned in BOQ/Specification has an inmpact on delivery for completion of project with respect to time lines mention in contract, shall be informed to Architects/Consultants / Client and take an approval for alternate make., All the cable and wires used in the project shall be FRLS

DISTRIBUTION BOARDS, Supply, Installation, Testing and Commissioning of MCB Distribution board as per approved installation dwgs., Reference Standard: IS 8623, Enclosure:1.2mm CRCA Sheet Steel, Powder Coated, DB type: Horizontal, 7 Segment for UPS DB's, Lighting, Emergency Lighting & Raw power or as specified., Door : Double Door, Protection : IP 42, Cable Entry : Top & Bottom, For UPS distribution RCCB shall be harmonic resistant (SI Series), Bus bar : Shall be tinned Copper and 200% rating for UPS DB Neutral Link, MCB's : 10kA 'C' Curve for Lighting & Raw power, 10kA 'D' Curve for UPS Distribution, Note: 1) Separate Earth bus & Neutral bus for each phase 2) Each Circuit shall have yellow ferrules with circuit number. 3) Accessories required for installation of DB's on Wall/Column/Gyp Board shall be considered 4) DB's shall be covered with powder coated (paint should match with DB Color) wire ways all around and up to ceiling to receive incoming circuits, how ever raceway shall be considered as a separate items & same shall be paid under raceway item. 5) Laminated A3 OR A4 size SLD & Control drawing copy shall be pasted inside DB door 6) Safe shroud for Neutral link shall be provided 7)All MCB's & Isolators should have provision for LOTO using Padlocks.

GROUND FLOOR KTCHEN DB-1 - 4 Way TPN DB Supply, erection, testing and commissioning of MCB DB double door type, IP 42 powder coated 4 Way TPN DB comprising of "C" curve MCB's , Incomer, 1 No - 63 Amps 4P 30mA RCCB, Outgoings, 12 NOS - 16A SP 10kA "C" curve MCB , Including all interconnections & accessories etc as reqd

GROUND FLOOR KTCHEN DB-2 - 8 Way VTPN DB Supply, erection, testing and commissioning of VTPN MCB DB double door type, IP 42 powder coated VERTICAL DB comprising of "C" curve MCB's , Incomer, 1 No - 63 Amps 4P 10kA MCB , Outgoings, 8Nos - 32A TP 10kA "C" curve MCB , Including all interconnections & accessories etc as reqd

GROUND FLOOR DB-1 - 6 Way TPN DB Supply, erection, testing and commissioning of MCB DB double door type, IP 42 powder coated 6 Way TPN DB comprising of "C" curve MCB's , Incomer, 1 No - 63 Amps 4P 30mA RCCB, Outgoings, 16 NOS - 6A SP 10kA "C" curve MCB , 2 NOS - 32A SP 10kA "C" curve MCB , Including all interconnections & accessories etc as reqd

DB-1 - 6 Way TPN DB Supply, erection, testing and commissioning of MCB DB double door type, IP 42 powder coated 6 Way TPN DB comprising of "C" curve MCB's , Incomer, 1 No - 80 Amps 4P 30mA RCCB, Outgoings, 10 NOS - 6A SP 10kA "C" curve MCB , 8 NOS - 32A SP 10kA "C" curve MCB , Including all interconnections & accessories etc as reqd

SWITCH & SOCKETS

Supply, Installation, Testing and Commissioning of the following Modularsockets with modular front plate, with suitable MS/PVC back box accessories as per the site conditions. Refer Standard: BS 1363, IS 3864, IS 1293 Terminal : Phosphor bronze Enclosure for Current carrying part; Thermoplastic/ABS plastic complying to environment recycling Frontplate: Thermoplastic /Polycarbonate complying to environmental recycling IP Class for Modular sockets: IP20 Note: Safety shutters to prevent accidental contact with live parts shall be provided. No indicator shall be provided for switches

Supply, Installation, testing and commissioning of 1No 16A Socket controlled by 16A switch for (RAW Power) applications (AC CONTROL)

Supply, Installation, testing and commissioning of 1No 16A Socket controlled by 16A switch for (RAW Power) applications

Supply, Installation, testing and commissioning of 1No 16A Socket for (GEYSER ,EXHASUT CONTROL) applications

Supply, Installation, testing and commissioning of 1No 16A Switch for (GEYSER ,EXHASUTCONTROL) applications

Supply, Installation, testing and commissioning of 1No 6A Socket controlled by 6A switch for (RAW Power) applications

Supply, Installation, testing and commissioning of 1No 6A Socket controlled by 6A switch for (RAW Power) applications (INDEPENDENT)

32A DP Switch with Indicator - 2 Module (MASTER SWITCH)

32A TPN+E POLY PROPELYNE PLUG & SOCKET WITH 32A 4P 30mA RCCB

Supply installation testing and commissioning of module modular metal back box for data, with necessary cutting chipping works, closing the same and making the wall/ floor strong, smooth finish.

3Module modular metal back box for VOICE

3Module modular metal back box for DATA

6A Switch 2W - 1 Module

6A Switch 1W - 1 Module with ‘Light’ Marking

6A Switch 1W - 1 Module with ‘Fan’ Marking

Blank Plate - 1M

FLUSH MOUNTING BOXES (GI)

Flush Box - 1/2 Module

Flush Box - 3 Module

Flush Box - 4 Module

Flush Box - 6 Module

Flush Box - 8 Module

Flush Box - 12/16 (2 row x 6) Module Metal Box

SURFACE MOUNTING BOXES (PLASTIC)

Surface Box - 1/2 Module

Surface Box - 3 Module

Surface Box - 4 Module

Surface Box - 6 Module

Surface Box - 8 Module

Metal Surface Box - 12/16 (2 row x 6) Module

LIGHT FITTINGS

Supply, Installation, Testing and Commissioning of Light fixtures and lamps with all accessories, fixing on the wall / ceiling/false ceiling with wooden blocks, screws ,hardware's ,suspended chain hooks as required as per the site conditions (including the earthing of fixture) Ballast: Electronic ballast THDshall be ≤10% Lamp type: LED color rendering index: >85 Color temprature: 6500K or as specified in respective line items Glare Index ≤ 19 Uniformity shall be 70% over 95% of the area. (350 lux @ 750mm level) Enclosure:CRCA sheet steel epoxy powder coated with antistatic treatment. Fixture shall be prewired up to terminal block with loopin-loopout facility IP Class:IP20 Note* 1. Mounting height shall be 2.7m from FFL in all areas. Suspension support height to be considered accordingly. 2. Dialux report to be shared for our review. 3. Mock up of light fixture to be done and necessary approval to be obtained before procurement.

9W WALL LIGHT FITTING WITH HOLDER,Ceiling Rose

20W TUBE LIGHT

18W RECESSED DOWN LED LIGHT

MIRROR LIGHT

LED Foot lamp

Water Tight Bulk Head Fitting suitable for 100 / 60 Watts Lamp with Guard Heavy Type

BOLLARD LIGHT FITTING

CEILING FAN

AC Exhaust Fan 375mm (15”) Sweep (Light Duty)

48” Ceiling Fan 5 Star Rated (1200MM),Ceiling Rose,FAN clamp

Stepped Electronic Square Type Fan Regulator

POINT WIRING

POWER SOCKET

Supply& laying of 2 x 4.0 sqmm + 1 x 1.5sqmm(earth) FRLS stranded copper conductor wires in 20mm dia MS conduits For First 6/16A Power Sockets, where ever shown in the layout / SLDdrawing circuit wiring scope shall be from From respective DB to first 16A, power socket only. but Excluding cost of Conduit, Switch , Socket , Modular Box & Front Plates.ie.,

Supply& laying of 2 x 4.0sqmm + 1 x 1.5sqmm(earth) FRLS stranded copper conductor wires in 20mm dia MS conduits For Second 6/16A power Sockets, where ever shown in the layout / SLD drawing looped with First 6/16A Socket ie., circuit wiring scope shall be from first 6/16A Socket to second 6/16A Power socket only.

INDUSTRIAL SOCKET

Supply& laying of 4 x 6.0sqmm + 2 x 2.5sqmm(earth) FRLS stranded copper conductor wires including termination on both ends with copper lugs in including MS Conduits/Flexible and necessary accessories as required - Pantry Equipment.and Three phase Industrial Socket

MASTER SWITCH 32A DP

Supply& laying of 2 x 6.0 sqmm + 1 x 2.5sqmm(earth) FRLS stranded copper conductor wires in 25mm dia MS conduits For First 32 DP Master switch, where ever shown in the layout / SLDdrawing circuit wiring scope shall be from From respective DB to first 32A, master switch only.but Excluding cost of Conduit, Switch , Socket , Modular Box & Front Plates.

Supply& laying of 2 x 4.0 sqmm + 1 x 1.5sqmm(earth) FRLS stranded copper conductor wires in 25mm dia MS conduits For First 32 DP Master switch, where ever shown in the layout / SLDdrawing circuit wiring scope shall be from From respectivefirst 32A, master switch to Geyser & AC control only. but Excluding cost of Conduit, Switch , Socket , Modular Box & Front Plates.

NORMAL LIGHTING/FAN

SITC OF 2 x 2.5sqmm + 1 x 1.5sqmm(earth) FRLS stranded copper conductor wires in 20mm dia FRLS PVC conduits For Lighting/fan circuit Mains From respective DB to First switch board as per Layout / SLD.

SITC OF 2 x 2.5sqmm + 1 x 1.5sqmm(earth) FRLS stranded copper conductor wires in 20mm dia FRLS PVC conduits For Lighting/fan circuit Mains From respective Master switch to First switch board as per Layout / SLD.

SITC OF 2 x 2.5sqmm + 1 x 1.5sqmm(earth) FRLS stranded copper conductor wires in 20mm dia FRLS PVC conduits For Lighting/fan circuit Mains from first switch board to subesquent switch boards as per Layout/SLD.

SITC OF 3 x 1.5sqmm (With earth) FRLS stranded copper conductor wires in 20mm dia FRLS PVC conduits For switch borad to Lighting/fan

CONDUITS & BENDS

Supply, Laying, Testing & commissioning of MS conduit on (Ceiling, Wall, In floor / concealed) etc for Lighting/Power wiring Gauge:16 SWG up to 32mm Dia & 14G SWG above 32mm Dia Material: MS with anticorrosive paint with threading on both the ends Accessories: MS with Threaded type NOTE: 1) MS Conduits as per IS 653, concealed at ceiling / laying in above false ceiling in multiples shall be supported by Slotted GI 'C' channel at distance not more than 0.5mtrs intervals. OR else with spacers & saddles at an intervals of 0.5mtrs 2) Accessories shall includes Bends, Collars, junction boxes, Spacers, saddles, screws, Flexibles (all are MS only). 3) Conduits shall be heavy duty & ISI marked 4) The number of wires drawn in each conduit shall be as per IS 694 code. 5) No different phases shall be drawn in same conduit 6) Conduit joints shall be done with threading proper accesories only

Conduit Pipe 19mm (3/4”) Heavy Gauge

Conduit Pipe 25mm (1”) Heavy Gauge

Conduit Pipe 32mm (11/4”) Heavy Gauge

Conduit Tee Bend 19mm (3/4”)

Conduit Tee Bend 25mm (1”)

Conduit Tee Bend 32mm (11/4”)

Conduit Solid Bend 19mm (3/4”)

Conduit Solid Bend 25mm (1”)

Conduit Solid Bend 32mm (11/4”)

Note: CLIENT reserves to supply any listed items, the contractor shall install the same at quoted installation price CLIENT reserves to change specification and makes of materials prior to procurement by contractor All the execution shop drawings shall be prepared by vendor and approval shall be taken from Consultants/Architects/Client before execution The sample of material used shall be provided by vendor as required for approval of Consultants/Architects/Client before procurement Incase any item required for quality execution is not included in tender BOQ, the same can be added by vendors with information to consultants, architects & Client If any items mentioned in BOQ/Specification has an inmpact on delivery for completion of project with respect to time lines mention in contract, shall be informed to Architects/Consultants / Client and take an approval for alternate make. All the raceways, bus trunking located on floor needs to be supported with proposer accessories, Vendor to consider all the assories while quoting All Data raceways & Cable tray used in project are perforated. Maximim size of perforrations shall not be more than 5-7mm

CABLE TRAYS AND WIREWAYS

Supply and Installation of the following sizes of Cable trays suspended from the ceiling or Along the wall or in trench or on floor, Refer standard: IS 1079 & 513 Material : GI / MS Finish: for GI - Pre Galvanized for indoor & Hot dip galvanized for Outdoor (NA) Finish: for MS - For indoior only - Powder coated ( colour as per architect choice) Thickness: 2mm Type: Ladder or Perforated or Solid Rung Spacing: 300mm Rung width: 35mm Supports: Up to 300mm wide using Hi-tech Rod and above 300mm wide using MS angle supports with anticorrosive paint at an intervals of 500mm. Accessories: Couplers, Bends, Reducers, Tees, Cross junctions & End cap shall be considered. The trays installed on floor shall be mounted on 'C' clamp Please note - The suppports for the trays and raceway shall be of the same material of that of the respective trays. Further MS supports shall also be powder coated. Colour of powder coating shall be as per Architect choice please do a mock-up before procurement.

CABLE TRAYS

150 mm x 50mm GI HOT DIP Powder coated tray

300 mm x 50mm GI HOT DIP Powder coated tray

Supply & installation of threaded GI rods of various diameter and GI slotted angle of various sizes including with necessary bolts, nuts, washers, etc

EARTHING SYSTEM

ELECTRODES

Supply, Installation, Testing and Commissioning of the Earth pits as per standard Refer Standard: IS 3043. IE rules 1956 Electrode: Cast iron for Corrosive Soil. Galvanized Iron/Non-galvanized Steel for Non Corrosive soil Plate Electrode: Copper Application: 1) CI or GI pipe electrode for Equipment Earthing 2) Copper/GI/CI plate or tripolar for System Earthing or UPS neutral and clean earthing Note: Work Related to chipping and plastering of floor area at the ground level for providing below mentioned earth pits shall be considered in interior vendor scope. Electrical Vendor to coordinate with PMC on the location of the Earth pits. Earthpit excavation and refilling will be in Electrical vendor scope Note: 1) Installation of pipe and plate electrode shall be carried out as per details given in IS 3043 2) Earthing connections shall be carried out as per details given in IS 3043 3) Pipe electrodes shall have 12mm drilled holes not less than 75mm from each other up to 2mtr of length from bottom to top. 4)The chamber construction shall be made as per details given in IS 3043(masonry enclosure not less than 300 x 300 x 300mm with CI/MS frame cover. 5) Funnel with wire mesh shall be provided on top for individual electrode for maintenance. 6) All copper flat should be brazed and all GI flats should be welded.

Supply, installation, testing & Commissioning of Earthing arrangements with GI Earth Plate including charcoal and salt with necessary excavation in all soils and to full depth as may be required and masonry work,re-filling the sides of foundation with excavated earth as per the standard specification and as directed by the Departmental Officers.

EARTHSTRIPS

Supply, Installation on trays/in ground/on wall/in trench etc, Testing and Commissioning of the Earth strips as per installation standard IS 3043 Strips above ground: GI Strips below groung: GI Accessories: Welding for GI/MS, Brazing for Copper, GI nut bolts for connection at eqpt end/PVC sleeves for copper strips/Epoxy Insulated mounts shall be considered

25 x 06 mm - GI flat

2.5 Sqmm CU wire for DB'D Body Earthing

Supply, installation, testing and commissioning of dedicated earth boxes of complete with 14 SWG sheet steel enclosure of suitable size with 600mm long 25x6mm GI. Strip on SMC inslulator for incoming & outgoing cables for earthing.

Supply, installation of earth bus link comprising of 25x6 GI with 10 Nos holes with SS bolts, nuts and washers. This shall be installed on insulated hylam supports & the Earth Bus should be enclosed with MS BOX, Rate shall be inclusive of the BOX & fixing accessories as required as per site condition.

LIGHTNING ARRESTER

SAFETY ACCESSORIES

AC Chargeable Emergency Lamp 2 x 11W PL Lamp with all connected accessories

2m x 1m Rubber Mat suitable for 11 KV installation confirming to IS

First Aid Box complete with all First Aid Medicines

Shock Treatment Chart fixed in glass frame

4 Nos. Fire Buckets made out of 40 x 40 x 6mm MS Angle

Metallic Danger Board as required by the Electrical Authorities

Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms

Earth Discharge Rod

OTHER PROVISION

Passenger Lift MRL, Speed 1.5 m/s with Stainless Steel Panels, Disable friendly, microprocessor based controller, VVVF drive, Fire rated doors and ARD. (M-2372)

8 Person

Add for every additional Floor over G+3 Floors

Civil - Academic Block

Cleaning removal of Heavy Jungle clearing the debris away from the site including cost of required tools and plant and necessary etc., all complete in all respect and as directed by the departmental officers. (W-0001)

Bored cast in situ piles Installation of vertical cast in situ bored piles of following dia using design mix of grade M 30 concrete (using hard broken stone graded chips of size 20mm and less) by setting the bored cast in situ pile equipments with all acccessories and tools at each of locations based on the sequence of operations as directed by the Engineer-in-charge, boring for the piles from ground level in all soils to the required depth below cut off level to carry a safe working load not less than specified using transit bore mud circulation method (using bentenite clay of required density) inclusive of pile driving accessories, temporary casing pipe, bentonite solution of 10% of concrete with required specific density, mobilisation, transferring, installation of pile driving accessories from one location to another, removal of mud from site upto a distance of 5km as directed by the departmental officers, the cost of shoe and length of pile to be embedded in the pile cap but excluding cost of steel and fabrication of reinforcement grills etc., complete complying with relevant standard specifications and as directed by the departmental officers. [The length of pile shall be measured from the top of shoe to the bottom of pile cap].

500mm dia

600mm dia

Chipping of RCC pile head of following dia pile to the required cut off level and clearing away the debris from site with an average lead of 5km etc., complete complying with relevant standard specifications and as directed by the departmental officers.

500mm dia

600mm dia

Mobilisation charges inclusive of transportation to site assembling and dismantling the rotary pile equipment employed for the works etc., complete complying with relevant standard specifications and as directed by the departmental officers. (Qtn)

Conducting Routine vertical compression load test for bored cast in situ RCC piles of following dia by direct loading in accordance with IS 2911 ( part IV) 1985 excluding cost of pile and dismantling the same after testing, including finishing pile head and supplying and erection of all kentledge of suitable magnitude as specified, labour, excavation, back filling compaction etc., complete complying with relevant standard specifications and as directed by the departmental officers (150% of pile capacity) c.500mm dia pile

600mm dia pile - Initial Testing Pile (2.5 times)

600mm dia pile - Vertical Test (1.5 times)

500mm dia pile - Initial Testing Pile (2.5 times)

500mm dia pile - Vertical Test (1.5 times)

Earth work excavation for foundation in all soils and sub-soils to the required depth as may be directed except in hard rock requiring blasting but inclusive of shoring, strutting, and bailing out water wherever necessary and refilling the sides of foundation with excavated earth in 150mm thick layers well watered rammed and consolidated and depositing the surplus earth in places shown clearing and levelling the site with an initial lead of 10 metres and lift as specified here under etc. complete in all respects complying with relevant standard specifications. (Including Refilling)

Supply and filling in foundation and basement with Stone dust in layers of 150mm thickness well watered, rammed and consolidated complying with relevant standard specification including cost of stone dust etc., all complete and as directed by departmental officer.

Plain cement concrete 1:4:8 (One of cement, four of sand and eight of hard broken stone jelly) for foundation using 40mm gauge hard broken stone jelly inclusive of shoring, strutting and bailing out water wherever necessary ramming, curing etc., complete in all respects complying with relevant standard specifications and as directed by the Departmental officers.

Flooring with a bed of CC 1:5:10 (one of cement, five of sand and ten of hard broken stone jelly) using 40mm size hard broken stone jelly and top left rough to receive the floor finish with required slopes including ramming, curing etc., all complete complying with relevant standard specifications.

Filling in foundation and basement and other similar works with Excavated earth in layers of 150mm thick well watered rammed and consolidated complying with relevant standard specification etc., all complete and as directed by the departmental officers.

Supply and filling the low lying area for the proposed formation of approch road with gravel in layers of 150mm thickness well watered, rammed and consolidated complying with relevant standard specification including cost of gravel etc., all complete and as directed by departmental officer.

Providing and Laying in position, Standardised concrete mix M-25 grade in accordance with is: 456 - 2000 using 20 mm and downgraded hard broken stone jelly for all rcc works namely column, column footings, plinth beam, grade beam, raft beam, raft slab etc., with minimum cement content of 350 kg/m3 and maximum water cement ratio of 0.50, including admixture (plasticiser/super plasticiser) in recommended proportions as per is :9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m) 7730 kg. of 20 mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10 -12 mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand for making 10m3 concrete but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing etc., complete complying with standard specification and as directed by the departmental officers. the coarse and fine aggregates to be used should comply with the requirements of is standards. (no separate payment will be made by the department for the excess usage of materials)

In Foundation and basement

Ground Floor

First Floor Lintel

Providing and laying in position, Standardised concrete mix M-35 grade in accordance with is: 456 - 2000 using 20 mm and downgraded hard broken stone jelly for all rcc items of works namely tee, ell or rectangular beams, lintel, parapet cum drops, waist and landing slab, canophy, circular column, fin projections, sunshades, window boxing slab, slab and other similar works with minimum cement content of 425 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser/super plasticiser) in recommended proportions as per is:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m) 7730 kg. of 20 mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10 -12 mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand for making 10m3 concrete but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing etc., and providing fixtures like fan clamps in the rcc floor/roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. the coarse and fine aggregates to be used should comply with the requirements of is standards. (no separate payment will be made by the department for the excess usage of materials).

In Foundation and basement

Ground Floor

First Floor Lintel

Second Floor

Third Floor

Providing and Laying in position, Standardised concrete mix M-20 grade in accordance with is: 456 - 2000 using 20 mm and downgraded hard broken stone jelly for all rcc works namely column, column footings, plinth beam, grade beam, raft beam, raft slab etc., with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.50, including admixture (plasticiser/super plasticiser) in recommended proportions as per is :9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m) 7730 kg. of 20 mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10 -12 mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand for making 10m3 concrete but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing etc., complete complying with standard specification and as directed by the departmental officers. the coarse and fine aggregates to be used should comply with the requirements of is standards. (no separate payment will be made by the department for the excess usage of materials)

Ground Floor

First Floor

Supplying, fabricating and placing in position of Mild steel Grills / Ribbed Tor Steels of all diameters for reinforcement for all floors including cost of binding wire, bending tying etc., all complete and as directed by the departmental officers.

Applying one coat of anticorrosive treatment on steel reinforcement rods (20 ltrs. Of anitcorrosive chemical for one mertic tonne of steel reinforcement rods) at site including a cost of required quantity of anticorrosive chemicals, (best approved quality) cement, consumables such as brushes, gloves and labour for anticorrosive coating etc. complete and as directed by the departmental officers. (The Quantity and brand of anticorrosive chemaical should be got approved by the EE before use).

Providing Form work and centering for reinforced cement concrete works including supports and strutting up to 3.30m height for plane surfaces as detailed below with all cross bracings using mild steel sheets of size 90cm x 60cm and MS 10 gauge stiffened with welded mild steel angles of size 25mmx25mmx3mm for boarding laid over silver oak or country wood joists of size 10cmx6.5cm spaced at about 90cm centre to centre and supported by casurina props 10cm to 13cm dia spaced at 75cm intervals and removing the same after a specified period without damaging the R.C.C works etc., complete complying with standard specifaction and as directed by the departmental officers.

For Column footings,plinth beam,Grade beam, Raftbeam,Raft slab etc.,

Plain surfaces such as Roof slab, floorslab, Beams, lintels, lofts, sillslab, staircase waist, portico slab and other similar works

For Square and rectangular columns and small quantities such as sunshade, parapet cum drops window boxiing, fin projection and other similar works.

For vertical walls

Providing additional Strutting to centering of R.C.C slab and beams of all surfaces or any other form works required at site during execution of work for every additional 1 metre height or part there of, but not less than 30 cm over the initial 3.30 mt height using approved make quality materials of props 10 to 13 cm dia @ 75cm c/c including cost of materials and labour charges etc., all complete complying with standard specification and as directed by the departmental officers.

Provideing Chicken mesh in beam joint areas in the building where ever necessary.

Brick work in CM 1:5 (One of cement and five of sand) using chamber burnt bricks of size 9”x4½”x3” (23x11.4x7.5 cm) in foundation and basement including dewatering wherever necessary proper setting, curing etc., complete with relevant standard specifications.

Brick work in Cement Mortar 1:6 (One of cement and six of sand) using Chamber burnt bricks of size 9”x4½X3” (23x11.4x7.5cm) for super structure in the following floors including labour for fixing the doors, windows and ventilator frames in position, fixing of hold fasts, scaffoldings, curing etc., complete in all respect complying with relevant standard specifications and drawings.

Ground Floor

First Floor

Autoclaved Aerated Concrete block masonry: Supplying and constructing of Autoclaved Aerated Concrete (AAC) block masonry using blocks having dimesions of 600 x 200mm and thickness 100mm to 300mm of density of 600 Kg/m3 with compressive strength not less than 3 N /mm2 conforming to IS 2185 (part III) 1985 from FFL till structural ceiling level or height as mentioned in drawing in cement mortar 1:6 (One of Cement and six of sand) for super structure in the following floors if required suitable plasticizer may also be added. The horizontal and vertical joint thickness should be approximately 10mm. Masonry works strictly be carried out as per IS 6041 - 1985 (Reaffirmed 1990).

The same shall be anchored properly with the structure. The work should be carried out as per the instruction of departmental officers. The rate including cost of form work, scaffolding, racking out joints, including materials, labour, tools, equipments all lead, lifts necessary finishing, curing etc., all complete complying with relevant standard specification. The quality and brand should be got approved from Executive Engineer before use).

Ground Floor

First Floor

Second Floor

Autoclaved Aerated 100mm Thick Block Masonry: Supplying & constructing of Autoclaved Aerated Concrete (AAC) block masonry using blocks having dimensions of 600 x 200mm and thickness 100 mm of density 600 Kg / m³ with compressive strength not less than 3 N/mm² conforming to IS 2185 (part III) 1985 from FFL till structural ceiling lvl or height as mentioned in drawing in cement sand mortar 1:4 (One of Cement and four of sand), if required suitable plasticizer may also be added. The horizontal and vertical joint thickness should be approximately 10 mm. Masonry works strictly be carried out as per IS 6041 - 1985 (Reaffirmed 1990).

Ground Floor

First Floor

Special ceiling plastering in cement mortar 1:3 (One of cement and three of sand) 10mm thick for bottom of roof, stair, waist, landing and sunshades in all floors finished with neat cement including hacking the areas, providing band cornice, scaffolding, curing etc., complete

Plastering with CM 1:5 (One of cement and five of sand) 12mm thick finished with neat cement including providing band cornice, ceiling cornice, curing, scaffolding, etc., complete in all respects and complying with relevant standard specifications.

Plastering with CM 1:5 (One of cement and five of sand) 20mm thick finished with neat cement including providing band cornice, ceiling cornice, curing, scaffolding, etc., complete in all respects and complying with relevant standard specifications.

Plastering with cm 1:3 (one of cement and three of sand ) 12 mm thick mixed with water proofing compound (CICO) at the rate of 2 kg / 10 sq.m including curing etc., all complete complying with relevant standard specification.

Providing pre-constructional Antitermite treatment including cost of chemicals labour as per standard specifications for preparing the area for treatment by spraying chemicals and other incidental charges etc.. complete. The rates should be for curing antitermite treatment from the plinth beam and brick masonry with super structure in contact with the back fill earth and at the junction on the walls. The top surface of filled earth for flooring and the soil along with the perimeter of the building by making holes with the crow bar and poured 5% termicide. “Chloripyrifos” and spraying the same termicide solution on the wooden frames and treating he other periphery of buildings etc., complete in all respects as per IS 6313 (part II)/ 1981 and as directed by the departmental officers.

Supplying and fixing of Teak Wood wrought and put up for frames of doors, windows, ventilators, cupboard and any other similar joineries works with necessary plugs, rebates for shutters, plaster grooves on all faces etc. , including labour charges for fixing hold fasts, complying with relevant standard specifications etc., in all respects.

Teak wood over 2.00 metre and below 3 metre length

Teak wood below 2.00 metre length

Supplying and fixing of single leaf Soild core flush door shutters with using boiled water resistance (BWR) teak wood ply as per IS 303-1989, the cross band and face veneers are to be banded with phenol formaldehyde synthetic resin in hot press both sides and manufacturing the shutter by using quality timber of termite proof and seasoned to moisture content not more than 10%, hot pressed with hydraulic press at a temperature of 150o to the norms as per IS 2002-1983 and TW Ply on one side with teak wook lipping around, 35mm thick including cost and fixing of Brass furniture fittings such as 3 nos 5” hinges, 2 Nos 6" Brass Towerbolt, 2 Nos 6" Brass Handle, 1 no Mortice lock with required screws with 3 keys with night latch, 1No 40mm dia & 60mm long rubber bush ,1 no Aluminium Door stopper with rubber bush with required Brass screws, labour charges for wrought and putup and fixing in position of flush shutters and painting the TW portion with two coats using 1st class synthetic enamel paint over one coat of primer and as directed by the departmental officers. (The quality and brand of materials should be got approved from the Executive Engineer before use.)

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug. (M-0673)

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work. (M-0674)

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work. (M-0675)

Supplying and fixing Mild Steel grills as per the design approved to verandah enclosure or gate including one coat of primer and labour for fixing in position etc. all complete

Supplying and applying of Full putty two coats with aprroved make wall putty for smooth finishing the new cement plastered walls including cost of putty, brushes, watering curing labour charges for apply putty, blade etc., complete as directed by the departmental officers. (The quality and brand should be got approved from the EE before use.)

Painting the false ceilling / walls two coats with 1st class ready mixed Interior emulsion paint of best approved quality colour and shade over a priming coat, including clean removal of dirt and dust etc., complete including cost of necessary brushes, labour charges, putty etc., complying with relevant standard specification. (The paint should be supplied by the contractors at his own cost.The quality and shade of the paint should be got approved by the Executive engineer before use.) (Inner)

Painting the false ceilling / walls two coats with 1st class ready mixed Exterior emulsion paint of best approved quality colour and shade over a priming coat, including clean removal of dirt and dust etc., complete including cost of necessary brushes, labour charges, putty etc., complying with relevant standard specification. (The paint should be supplied by the contractors at his own cost.The quality and shade of the paint should be got approved by the Executive engineer before use.) (Outer)

Supplying and fixing of Double charges Vitrified Tiles of size 59.5x59.5cmx10mm for flooring and other similar works (Best approved quality, colour and shade and the same shall be got approved from the Executive Engineer before use) in cement mortar 1:3 (one of cement and two of sand) 20mm thick including fixing in position, cutting the tiles to the required size wherever necessary pointing the joints with grout (Tile joint filler), curing, finishing etc., all complete and as directed by the departmental officers.

Supplying and fixing of Ruby Red colour Granite slab super fine polished with machine cut edges of 18 to 20 mm thick for flooring (Best approved quality and the same shall be got approved from the Executive Engineer before using) over cement plastering in CM 1:3 (One of cement and three of sand) 20mm thick including fixing in position, cutting the tiles to the required size wherever necessary, pointing the joints with coloured cement, curing, finishing etc., all complete and as directed by the departmental officers.

Providing Single nosing to the edges of Granite slab of 20 mm thick including labour, power consumption, tools & plants required, true to horizontal etc., for Kitchen platform in all floors and as directed by the departmental officers.

Providing Grooving the Granite slab including cost of all labour charges etc., all complete and as directed by the departmental officers.

Supplying and fixing of Ceramic Tiles Anti skid without corrugated design for flooring and other similar works (Best approved quality, colour and shade shall be got approved from the Executive Engineer before using) over cement mortor 1:3 (One of cement and three of sand) 20mm thick including fixing in position, cutting the tiles to the required size wherever necessary, pointing the joints with Grout (Tile joint filler), curing, finishing etc., all complete and as directed by the departmental officers

Supplying and fixing of Colour glazed tiles (Best approved quality and the same shall be got approved from the Executive Engineer before using) over cement plastering in CM 1:2 (One of cement and two of sand) 10mm thick including fixing in position, cutting the tiles to the required size wherever necessary, pointing the joints with coloured cement, curing, finishing etc., all complete and as directed by the departmental officers.

Finishing the top of Terrace floor with one course of solar reflective water proof, heat proof and cool roof ceramic tiles of size 300mmx300mmx8mm thick of approved quality laid in cement mortor 1:3 (one part of cement and three parts of sand) 20mm thick over base concrete mixed with calcium based mineral powder (60 kg for 1000 sqft) (before laying tiles, the tiles should be dipped with salin based nano liquid) and top Grouting with cement mortar 1:3 (one part of cement and three parts of sand) mixed with white cement, silicon powder and polimer additives (20kg for 1000 sqft.) and joint pointed with zycosil oil (200gm for 1000 sqft.) after grouting acrylic salin based liquid including cost of base concrete 1:2:4 mix using 6-10mm chips - 40mm thick etc., complete complying with standard specifications including cost of all materials, labour charges for lifting to open terrace, laying and finishing and other incidental charges etc., complete and as directed by the departmental officers. (The Brand and quality of tiles should be got approved from the Executive Engineer before using)

Weathering Course with concrete broken brick jelly 20mm gauge in pure burnt lime stone slaked and screened (No Sand) over RCC Roof Slab with proportion of brick jelly to lime (fat lime) being 32: 12 1/2 by volume well beaten with wooden beaters for giving the required slope and thickness complying with relevant standard specification and as directed by the departmental officers.

Providing Granite Tile of 10mm thick, wall cladding 1:3 (one of cement and three of sand ) 12 mm thick including finishing and fixing in position complying with relevant Standard specifications etc., complete in the following floors (Measurement will be taken including bearing also) as directed by the departmental officers (Quality of Granite slab shall be got approved by the Executive Engineer before fixing. a. In Ground Floor

Supplying and laying of Designer Interlocking Paver blocks 63mm thick to take the load of 40N/sqmm, including water, electricity, leveling the ground and consolided earth etc., all complete and as directed by the departmental officers. (The Brand quality of materials should be got approved from EE before use)

Supplying and fixing stainless steel hand railing 304 grade with top railing tube of 50mm 304 grade with top railing tube of 50mm dia of 12 gauge and 2.5mm wall thickness, vertical tube of 40mm dia of 14 gauge and 2mm wall thickness with 900mm clear weight at requied intervals with 2 lines of horizental tube of 25mm dia of 16 gauge and 1.6 mm wall thickness, 62.5mm dia front post ball set and restical base cub of 16 gauge and wall thickness of 1.6mm including polishing, buffing, fabrication and erection in the places shown by the departmetnal officers and embeded in the places with PCC 1:2:4 using 20mm stone jelly making holes and redoing the same and labour charges, power consumption charges etc., all complete complying with relevant standard specifications and as directed by the departmental officers. (M-0651)

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete (M-0652)

Painting the new wood work with two coats of approved first class synthetic enamel ready mixed paint in addition to one coat of primer of approved quality and shade, the paint should be supplied by the contractor at his own cost (The quality and the shade of paint should be got approved by the Executive Engineer before use) complying with relevant standard specifications.

Painting the new Iron work and other similar works such as PVC /ASTM Pipes, Kerb Stone and grills with two coats of approved first class synthetic enamel ready mixed paint of approved quality and brand, the paint should be supplied by the contractor at his own cost. (The quality and the brand of paint should be got approved by the Executive Engineer before use) complying with relevant Standard specifications.

Providing and making circular cut of 110 mm dia in RCC or slab at required location, including cutting, finishing the edges neatly, making good the disturbed surfaces, complete as directed by the departmental officers.

Construction of Inspection chamber size 60 x 60 x 75 cmwith brickjelly cement concrete 1:3:16 ( One of cement, eight of sand and sixteen of broken brick jelly 40mm gauge 15cm, thick for foundation and 23cm thick brick mansonry in c.m 1:6 using stock bricks of size 9"x4 3/8"x2 3/4" and plastering with c.m 1:3 (one of cement, three of sand and four of hard broken stone 20mm gauge) 5cm thick precast cover slab excluding the cost and fabrication of reinforcement grills but including benching channelling fixing the cover slab in position curing, finishing etc., complete in all respects.

Providing Rain water harvesting pit by augering 300mm dia bore pits to a depth of 5.50m overall depth and filling with stone jelly of 40mm size including earth work excavation 1m dia, 600mm depth and filling with filling sand to a depth of 300mm filling sand over the stone jelly and covered with Pre-cast RCC Perforated slab of 40mm thick excluding the cost and fabrication of reinforcement grills but including precasting, moulding, curing, finishing and fixing in position etc and all complete as directed by the departmental officer.

Providing pit

Augering 30cm dia

Supplying and fixing Hydraulic Door Closer of various sizes of approved quality using Aluminium Extruded Section Body Tubular Type Universal Hydraulic Door Closer with Double Speed Adjustment (with ISI Monogram) including labour charges for fixing etc., complete complying with relevant standard specifications. (The brand and quality of hydraulic door closure should be got approved from EE before use ) (M-0311)

STRUCTURAL GLAZING WITH STICK SYSTEM

Structural glazing is a system of curtain wall in a building where the window framework is provided from floor to floor. This framework will consist of suitable verticals and horizontals fixed to the structural beams and slabs with well-designed clamps through bolts and nuts to withstand the wind pressure of 200 kg/m. Glass is fixed to the Aluminium through spacer and silicon sealant, so that no aluminum frame is seen from outside after fixing of glass. The individual specifications are: All Aluminium Profiles will be Indian Standard HE-9, 63400 grade, The pheripherry shall be of size of 113.0mm x 58.0mm x 2.0mm thick Rectangular Box Section, The transom shall be of size of 64.0mm x 57.0mm x 2.0mm thick Lip Section, The mullion shall be of size of 112.0mm x 57.0mm x 2.0mm thick Lip Section, Silicon sealant of Weather & Structural of WACKER Germany or equivalent, All aluminium section will be Electro colour anodized with anoxic film thickness of minimum 10- 15 micronze thickness, 6.0 mm x 15.0 mm spacer used for the purpose of Sealant bite to hold the glass , expansion and contraction, also to withstand the wind pressure. Including the Cost and supply of 5.0mm thick Reflectasol Green Heat Strengthened Glass as per Engineer approval.

MAIN ENTRANCE - FIXED CUM FRAMELESS DOUBLE LEAF DOOR ( Patch fittings Door )

Providing and fixing of Single door with 12.0mm Toughened clear Glass and necessary DOORMA xlc / HONNEX GERMANY make patch fittings Door set with top patch, bottom patch, lock, pivot ,Floor Spring, Door Handle of 400mm, Glass fixing with Clear Silicon Sealant at the bottom area & intermediate Glass to Glass joint, complete with all necessary fittings as per site condition.

GLASS DOME

Supply and erection of M.S. Dome with Laminated Glass at the Top of the Building, Using 96.0mmx 48.0mmx 4.0mm thick MS Rectangular box section in Every 4 feet interval horizontally and vertically, 100mm x 100mm x 8mm thick Base Plate, 78 x 57 x 2.0mm thick Curtain wall section fixing at top of the MS Support, 11.52 mm laminated Glass fixing with Aluminium pressure Plate and Cover Cap assure the dome leak proof and complete with necessary fittings as per site Conditions.

Supply, installation and fixing of dynamic façade using 10” × 5” split weathering tiles, repurposed from conventional terrace flooring application, mounted within custom-fabricated mild steel / galvanized steel frames, complete. The tiles shall be loosely supported and not rigidly fixed, permitting controlled movement under wind pressure to achieve a passive dynamic façade effect, without use of any mechanical or motorized system. The item shall include design, fabrication, erection, alignment, and anchoring of supporting metal framework, including all brackets, clamps, bolts, nuts, washers, and corrosion-protection treatment, complete as per approved drawings and directions of the Engineer-in-Charge. Rate shall include all materials, labour, tools, tackles, scaffolding, leads, lifts, and incidentals, complete in all respects.

PLUMBING WORKS

Supplying and fixing the following dia PVC (SWR) pipe and relevant specials including packing the joints with rubber lubricant fixing them into walls with necessary wooden plug screws, holding wherever necessary and making good of the dismantled portion with necessary connections to sanitary fittings etc., complete in all respects as directed by the departmental officers.

110mm dia PVC SWR pipe including all required PVC specials etc., all complete.,

75mm dia PVC SWR pipe including all required PVC specials etc., all complete.,

Supplying, laying, fixing and jointing the following PVC pipes as per ASTM D - 1785 of schedule 40 of wall thickness not less than the specified in IS 4985 suitable for plumbing by threading of wall thickness including the cost of suitable PVC/GI specials /GM specials like Elbow, Tee reducers, Plug , unions, bend, coupler, nipple/ GM gate valve, check and wheel valve etc., wherever required above the ground level including the cost of teflon tapeetc., Fully concealed in walls to the proper gradient and Alignment and redoing the Chipped portion of Masonry etc.,all complete and as directed by the departmental officers. 50mm ASTM (D schedule 40 threaded) PVC pipe with necessary PVC/GI specials

Supplying and fixing 150mm x 100mm size stone ware Gully trap with iron gratings over a bed of 150mm thick brick jelly concrete in CC 1:8:16 (one of cement, eight of sand and sixteen of broken brick jelly) using 40mm size brick jelly and brick masonry wall 114 mm thick using chamber burnt bricks of size 9”x4-1/2”x3” (23x11.4x7.5cm) in cm 1:5 (One of cement and five of sand ) plastered with CM 1:3 (One of cement and three of sand) 12mm thick etc., complete and as directed by the departmental officers.

Supplying and fixing of PVC Nahani Trap not less than 75mm 4 way / 2 way (Superior variety) having minimum of water seal of 50mm confirm to relevant I.S. specifications with its latest amendments including resting on the bed of brick jelly resting on the bed of brick jelly concrete 1:5:10 (One of cement, five of sand of ten of 40 mm gauge brick jelly) etc., complete as directed by the departmental officers (The PVC Nahani Trap should be got approved from the EE before use)

Supplying and fixing EWC superior variety (White) 500mm including cost and fixing of double flapped coloured plastic sheet cover, PVC flushing cistern in appropriate level as directed by the departmental officers at a maximum level of 5’6” and of approved brand of 10 litres capacity including fittings such as CI brackets. PVC connection, GM wheel valve, Hex Nipple, etc., complete (Brand, colour of EWC and plastic cover shall be got approved from the Executive Engineer before fixing)

Supplying and fixing of 160mm dia PVC SWR pipe for Rain water down fall pipe with necessary gratings, shoes, bends, off sets, clamps, teak woods plugs, and of approved quality and including fixing C.I. gratings at the junction of parapet and floor or roof slab etc., including finishing etc., complete complying with relevant standard specifications.

Supply and delivery of 110mm dia UPVC - Non Pressure Pipes as per IS 15328/2003,SN8- SDR 34 with excise duty suitable for plumbing by threading of wall thickness fixing on wall to the proper gradient and alignment and redoing the chipped of masonry etc., complete complying with relevant standard specifications and as directed by the departmental officers. (The pipe quality and brand should be got approved from the EE before use ).

Supplying and fixing of porcelain wash basin superior variety of size 22”x16” (550x400mm) including cost and fixing of CI brackets, pvc waste pipe required grating, cp tap, wheel valve/ Bob cork, pvc, connection, cp waste plug, with aluminium chain etc., complete in all respects (washbasin shall be got approved by the Executive Engineer before fixing)

Supplying and fixing of approved brand Porcelain Flat Back urinal superior variety including cost of Urinal lead pipe, waste pipe, 15mm wheel valve, TW plug and lobour for fixing etc., all complete as directed by the departmental officers (Thebrand and quality shall got approved from the Executive Engineer before use)

Supplying and fixing of Granite of 18 / 20mm thick in all floors for urinal partition including for labour charges for fixing and polishing etc.. all complete as directed by the departmental officers

Supplying, laying, fixing and jointing the following PVC pipes as per ASTM D - 1785 of schedule 40 of wall thickness not less than the specified in IS 4985 suitable for plumbing by threading of wall thickness including the cost of suitable PVC/GI specials /GM specials like Elbow, Tee reducers, Plug , unions, bend, coupler, nipple/ GM gate valve, check and wheel valve etc., wherever required above the ground level including the cost of teflon tapeetc., Fully concealed in walls to the proper gradient and Alignment and redoing the Chipped portion of Masonry etc.,all complete and as directed by the departmental officers.

50mm dia Astm D schedule 40 threaded Pvc pipe with necessary PVC/GI specials

32mm dia Astm D schedule 40 threaded Pvc pipe with necessary PVC/GI specials

25mm dia Astm D schedule 40 threaded Pvc pipe with necessary PVC/GI specials

Supplying, laying, fixing and jointing the following PVC pipes as per ASTM D - 1785 of schedule 40 of wall thickness not less than the specified in IS 4985 suitable for plumbing by threading of wall thickness including the cost of suitable PVC/GI specials /GM specials like Elbow, Tee reducers, Plug , unions, bend, coupler, nipple/ GM gate valve, check and wheel valve etc., wherever required above the ground level including the cost of teflon tapeetc., Fully concealed in walls to the proper gradient and Alignment and redoing the Chipped portion of Masonry etc.,all complete and as directed by the departmental officers. 20mm ASTM (D schedule 40 threaded) PVC pipe with necessary PVC/GI specials

Aluminium sliding door :- Supplying,fabricatingandfixinginpositionofAluminiumanodisednaturalcolourmattfinishofsingleleaffullypanelledslidingdoorwith12mmthickbothsideprelaminatedpartileboardattheShutterbottomrail:[email protected]/m,Top&[email protected]/m,[email protected]/m,Runningchannelsection:[email protected]/m,[email protected],[email protected]/mfulllengthofhandlesonbothsides,lock,roller,includingcostofmaterials,labourchargesandpowerconsumptionchargesrequiredforfabricationincludingchipping,dismantlingandwakingholetotherequiredextentinRCCcolumn,beammasonrywithpowerdrillwherevernecessaryandredoingthedamagedportiontotheoriginalconditionafterfixingetc.complete.AlltheAlu.sectionsaretobeanodised.withmattfinishunderelecticallycontolledconditioninaccordancewithIS1868/1962 for an average anodic film thickness of 15 microns etc

Supply and Delivery Fabrication of MS doors and windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. Size 1x2m

Supplying and Fixing MS Ladder width 45cm using 50 x 50 x 6mm MS Angle.

Supplying and fixing of Stainless Steel Health Faucet approved quality with ISI mark ( Health facet shall be got approved from the E.E. before use.) including all accessories etc. complete complying with relevant standard specifications and as directed by the departmental officers. (M-0656)

2.8 Lps at 22 M head.(DWS Booster Pump) (1 no. of working + 1 no. standby = 1 set)

Installation, Testing & commissioning of approved make submersible Clearwater lifting pump set with suitable horse power motor to each pump to discharge with control panel & all necessary accessories, conducting trail run, providing necessary civil foundations and base frame with all accessories like pressure gauge, control valve etc., and consumables, maintaining the system for the period of one year. Rate shall include all Electrical panel work connected to existing Electrical cable arrangement, etc. complete. Incoming Electrical cable to starter panel will be under scope of Electrical work. Transfer of water from UG Sump to Over Head Water Tank.

Flow : 1.2 lps Head :16-20 MWC No. of pumps : 2 (1 working + 1 Standby) Type : Submersible Application : Clear water transfer Time : 0.50 Hours

Constructing Masonry Chamber with internal size of 900 x 1200mm and up to 1500mm deep including necessary earth work excavation, laying 150mm thick 1:3:6 mix concrete using 40mm stone jelly in foundation, 230mm wide Brick work CM 1:5 mix, plaster interior and exterior with CM 1:4 for 15mm thick, providing 600 x 600mm size manhole cover & frame of medium duty, providing R.C.C roof slab over chamber in 1:1.5:3 mix with suitable reinforcement, providing and removing of wooden form work, refilling the sides with excavated earth, disposing off the surplus earth within the site, etc complete and as directed by the site Engineer.

Supplying and fixing, approved make PVC "Deep seal ‘P’ Trap" with 50mm water seal and vent horn, and 100mm dia outlet fixing to a perfect position, laying cement concrete alround in 1:3:6 mix with 20mm size stone jelly, providing and fixing suitable size SS grating with frame in PVC, providing 110mm dia PVC pipe over trap to make up the level of platform for Urinal portion, cutting concrete or making holes, restoring the damaged portion to their original condition etc. complete.

Supply and fixing Following chromium plated bath room fittings of connecting to water pipe using teflon tape over threaded portions, Including supplying and fixing CP Nipples to connect the water supply pipe to CP fittings, testing for leak proof,etc complete.

Supply and fixing, Long Neck Pillar cock with aerator.

Supply and fixing, 15mm dia 2 way bibcock with wall flange.

Supply and fixing, 15mm dia Angle valve stop cock long inlet threads with wall flange.

Supply and fixing, 32mm dia Bottle trap with extension piece & connecting Hose.

Supply and fixing heavy quality 32mm dia waste coupling with grating fixing to urinals - produce sample for approval.

ELEVATORS Passenger Lift MRL, Speed 1.5 m/s with Stainless Steel Panels, Disable friendly, microprocessor based controller, VVVF drive, Fire rated doors and ARD. (M-2372)

8 Person

ELECTRICAL WORKS

LT CABLES & TERMINATIONS

Supply, Laying, Testing and Commissioning of stranded XLPE/PVC insulated, FRLS Armoured/Unarmoured/Flexible, Aluminium/Copper conductor, laid over Galvanized or MS supports/in excavated Trench/in duct/fixing on walls including Galvanized clamping support to the cable as per approved installation dwg. Circuit identification tag made of stainless steel should be attached with the concerned cable alongwith the test report of following sizes of cable to be submitted by the contractor at the time of delivery of material at site Refer Indian standard Specification: IS 1554, 7098, 5831, 3975, 694(Earthing cables) Installation: IS1255 & IS732 Multicore/Single core Armoured/Un-armoured cable Insulation: As specified below Inner sheath: Extruded PVC only for Multicore Outer sheath: Extruded Type ST2 PVC PVC Cable shall be a tough outer sheathing of PVC FRLS insulating material in standard colours. Voltage grade:1100Volts Armoure: Galvanized Steel strip/Wire for multicore Non Magnetic Aluminum Wire/Strip for Single core

Power Cables(Aluminum cables)

3.5C x 185 Sq.mm XLPE AR Al

3.5C x 120 Sq.mm XLPE AR Al

3.5C x 95 Sq.mm XLPE AR Al

3.5C x 35 Sq.mm XLPE AR Al

3.5Cx 25 Sq.mm XLPE AR Al

4C x 16 Sq.mm XLPE AR Al

2 core 2.5sq.mm PVC copper interconnection cable

Single Core Copper Unarmoured cables(Cost shall include necessary glands, lugs and termination) Insulation: XLPE Specification: Confirm to BS 7211/ IS 7098 for UPS power distribution, Installation: IS1255 & IS732. Single core cables shall be laid in flexible GI conduit. Cost shall include cost for GI Flexible concuit.

1Cx25SQ.MM

1Cx4SQ.MM

Flexible Copper Earthing Cables including terminations. Note: Outer sheath for earthing cable shall be Green color Note : inner sheath is not required Standard : IS 694 Insulation: Class A PVC (Cost shall include necessary glands, lugs and termination)

1Cx10SQ.MM .CU.UNAR.CABLE

LT CABLE TERMINATION

Supply, Installation, Testing and Commissioning of Compression type cable gland, Aluminium sockets for Aluminium cables / copper sockets for copper cables, insulation tape, anti corrosive paste, brass clamps for gland earthing with 14 SWG copper wire to connect to nearest earth flat. Refer Standard: IS 12943 for single compression, BS 6121 for Double compression(NA) Gland type : Brass with nickel plated (Double compression) Compression : Double Sealing Ring : Natural rubber for indoor, Neoprene for Outdoor Wherever copper cable connect to GI strips, the lugs shall be tinned copper lugs fitted using shake proof assembly screws, washers and 'nylock' or similar nuts.

Power Cables(Aluminum cables)

3.5C x 185 Sq.mm XLPE AR Al

3.5C x 120 Sq.mm XLPE AR Al

3.5C x 95 Sq.mm XLPE AR Al

3.5C x 35 Sq.mm XLPE AR Al

3.5Cx 25 Sq.mm XLPE AR Al

4C x 16 Sq.mm XLPE AR Al

LT PANELS DISTRIBUTION BOARDS ,DG & APFCR

Supply, Installation, Testing and Commissioning of Indoor type LT Switchboards, Floor mounting type, Bottom/Top entry. Refer enclosed SLD Refer standard : IS 13947, 8623(part-1) Enclosure: Compartmentalized Single front CRCA Doors:2mm Body:2mm Gland:3mm covers and partitions:1.6mm. UPS Panel shall be considered Aluminum Gland sheet with 3mm thick IP class:IP44 for Indoor/IP65 with weather proof enclosure for outdoor Bus bars: Electrolytic grade conductivity as per standard IS 5082 Bus bar Material: As per SLD. All copper bus bar should be tinned. Bus bar suppotrs: DMC/FRP/SMC Bus bar joints: Shrouded/Tinned Protection releases: As specified Ics=Icu for all breakers Utilization category: All MCCB/ACB's shall be Cat: A except ACB's for Ltg & raw power input distribution panel shall be with Cat: B . Louvers:Busbar chamber shall have louvers with fine mesh inside Shade: Epoxy powder coated RAL 7032 Design: Modular Form 4B Type 6 for panel construction with common cable chambers. No live parts allowed in cable chambers. Cable entry: As per site condition SPD should have N/O contact for remote indication with on lndication lamp Bus bar insulation: The bus bar shall be covered with heat shrinkable FRLS PVC sleeves at all non contact points in colour of red, yellow, blue and black and the arranged in accordance with IS-5578

MAIN PANEL-1

A) Incomer-1 400 AMPS,TPN, Microprocessor based MCCB with Motorised Closing Mechanism of 36 kA Short Circuit Rating with O/L and S/C Protection, Earth fault and Neutral current protection.with shunt coil & Earth fault Relay with CBCT. B) Indication & Metering: 1 Sets of R,Y,B phase indicating lights (LED-TYPE) controlled with control 6A MCB, 1Sets of 3 phase, 4 wire,400A/5A, Digital flush type Class-I accuracy multifunction meter with RS485 modbus connectivity. 1 No. 400A/5A, Class-I, 5VA burden moulded CT's. C) Busbar: 400 A, TPN, 36KA AL Busbar Chamber for the entire length of the Panel as per specification 50 KA SPD ( SPD shall be with potential free contact ) TYPE-1 for three phase with suitable HRC fuse in the incomer & ON LED indication lamp-1No D) Outgoings : 200 Amps TPN TMD based MCCB with Manual Closing Mechanism of 36 kA Short Circuit Rating, with Thermal O/L and Magnetic S/C Protection -1 Nos 160 Amps TPN TMD based MCCB with Manual Closing Mechanism of 36 kA Short Circuit Rating, with Thermal O/L and Magnetic S/C Protection -1 Nos 125 Amps TPN TMD based MCCB with Manual Closing Mechanism of 36 kA Short Circuit Rating, with Thermal O/L and Magnetic S/C Protection -1 Nos 80 Amps TPN TMD based MCCB with Manual Closing Mechanism of 36 kA Short Circuit Rating, with Thermal O/L and Magnetic S/C Protection -4 Nos 63 Amps TPN TMD based MCCB with Manual Closing Mechanism of 36 kA Short Circuit Rating, with Thermal O/L and Magnetic S/C Protection -6 Nos

APFCR

60KVAR APFCR A) Incomer : 1No 1No - 315 Amps TP+N TMD based MCCB with Manual Closing Mechanism of 36 kA Short Circuit Rating with E/F Protection. B) Indication & Metering: 1 Sets of R,Y,B phase indicating lights (LED-TYPE) controlled with control MCB's and breaker ON / OFF / TRIP indications with power factor meter. C) Busbar: 315A, 36KA TPN Aluminium Busbar Chamber for the entire length of the Panel as per specification 50 KA SPD class B+C for three phase - with LED indication D) Outgoings : 63 Amps TP TMD based MCCB with Manual Closing Mechanism of 36 KA Short Circuit Rating, with Thermal O/L and S/C Protection - 1 No. 40 Amps TP TMD based MCCB with Manual Closing Mechanism of 36 KA Short Circuit Rating, with Thermal O/L and S/C Protection -2 No. 25 Amps TP TMD based MCCB with Manual Closing Mechanism of 36 KA Short Circuit Rating, with Thermal O/L and S/C Protection - 1 No. 25A TP Contactor, 5 KVAR Capacitor Bank with 7% Detuned Reactor - 1 No 40A TP Contactor, 10 KVAR Capacitor Bank with 7% Detuned Reactor - 2 No 63A TP Contactor, 25 KVAR Capacitor Bank with 7% Detuned Reactor - 1 No

CT METER

A) Incomer-1 500A TPN FUSE B) Busbar: 315 A, TPN, CU Busbar Chamber for the entire length of the Panel as per specification 1No. 315A/5A, Class-I, 10VA burden moulded CT's. C) Outgoings : 315 Amps TPN TMD based MCCB with Manual Closing Mechanism of 36 kA Short Circuit Rating, with Thermal O/L and Magnetic S/C Protection -1 Nos

400Amps 4P ATS

40kVA UPS

SITC of micro processor controlled True On line double conversion IGBT based 3 Phase input and 3 phase 415V output 40 KVA UPS. Input and Output Isolators shall be part of the UPS. UPS should have unity power factor. Note: 1. The UPS would function in Isolated redundent mode. Vendor to confirm that the cable lengths are acceptable to them as per drawings. 2.Suitable MS stand (adjustable upto 300mm Ht) for each UPS duly painted to be considered- The Height of the stand would be confirmed by the PMC as per the site condition.

UPS MODULES

200KVA DG SET

Design, manufacture, supply, erection of Outdoor type 200 kVA DG set with CPCB IV+ Complied (Prime Duty) with base frame , Engine mounted radiator & directly coupled to alternator with earth fault protection, AMF. Engine: Perkins / Cummins / Caterpillar / MTU / Volvo Alternator: Stamford / Leroysomer 415V, 50 kVA , 50Hz, 3Phase Mineral wool : Rockwool, Isover, Lloyd Exhaust Pipes : Tata, Jindal Batteries: Exide, Panasonic, Amaron Note: The DG Set would be mounted at Ground Level adjecent to Electrical room. Vendor to visit site, study the same and quote accordingly. Vendor to consider suitable enclosure to achieve a noise level of less than 75dBA at 1 mtr distance at all the points around the Acoustic Enclosure and at any load conditions between 0 to 100%. Weightage would be given to vendors offering systems with lowest possible noise level. Accessories for DG set which is to be included in the above price Fuel tank 400 Ltrs Batteries, Battery charger & Leads AVM Pads Residential Silencer. First fill of lube oil, filter, other consumables , Earth fault relay. Alternator adopter box with extended bus bars including differential protection Class PS CTs.

Design, manufacture, supply, erection of Outdoor type 200 kVA DG set with CPCB IV+ Complied (Prime Duty) with base frame , Engine mounted radiator & directly coupled to alternator with earth fault protection, AMF. Engine: Perkins / Cummins / Caterpillar / MTU / Volvo Alternator: Stamford / Leroysomer 415V, 50 kVA , 50Hz, 3Phase Mineral wool : Rockwool, Isover, Lloyd Exhaust Pipes : Tata, Jindal Batteries: Exide, Panasonic, Amaron Note: The DG Set would be mounted at Ground Level adjecent to Electrical room. Vendor to visit site, study the same and quote accordingly. Vendor to consider suitable enclosure to achieve a noise level of less than 75dBA at 1 mtr distance at all the points around the Acoustic Enclosure and at any load conditions between 0 to 100%. Weightage would be given to vendors offering systems with lowest possible noise level.

DG set Controller to provide Engine and Alternator protection . Controller shall be electronic type to handly sudden raise in load. Provision for BMS connectivity. Control panel shall also house KWH meter. The set mounted panel will include 400A 4P MCCB 36 kA , separate EFR , metering etc., Design, Manufacture, Supply, Installation, Testing and Commissioning of the Auto start/ stop outdoor type AMF Control Panel with 1 No 400A 4P 36KA MCCB with microprocessor based relay with display & LSIG protection as Incoming and with all required and standard accessories with annunciator window, metering instruments, indication lamps, hooter etc.., and required accessories as per the specification enclosed . Outdoor type Acoustic Enclosure suitable for DG set in line with PCB & Electricity board norms for Comercial Building. Weightage would be given for Vendors providing DG with lower noise levels.

Exhaust System

Design, manufacture, supply, installation, testing and commissioning of MS exhaust pipe class B of suitable size for 200 KVA exhaust line, as per manufacturer's recommendation with thermal insulation using mineral wool of density 48Kg/cm.sq and cladding with 0.8mm aluminium sheet for engine exhaust . The rate shall be inclusive of necessary, bends, flanges, flexible stainless steel bellows, gaskets, fixing of hospital silencer supplied along with the engine, MS angle iron supports for the pipe and the silencer, condensation removal plug, inspection point, welding arrangements as specified to suit the site conditions. The tenderer shall submit calculation along with the size offered for the DG set. exhaust manifolds of DG shall be fed to the DG Exhaust pipe . The end of the exhaust pipe shall have end cowl for protection from rain and bird screen. ( rate for MS material used for supporting the exhaust pipe outside the acoustic enclosure will be paid seperately) . the exhaust pipe inside the acoustic enclosure should be insulated with mineral wool with aluminium sheet cladding of sufficient dia to prevent heat radiation from exhaust. (Vertical length of piping can be considered as approximately 15 metres.). Steel Supports / Structures Required for above including all masonry, consumables and hardware etc. supports for exhaust piping etc. Scaffolding & associated civil works as required for exhaust pipe installation as per site condition.

CONTROL CABLEING

Supply, laying & termination of FRLS PVC armoured cu conductor control cables for the DG set

4Cx2.5 sqmm - 3 phase sensing and battery charger (1 lot)

24cr x 2.5 sqmm

14cr x2.5sqmm

7cr x2.5sqmm

24cr x 2.5 sqmm termination

14cr x2.5sqmm termination

7cr x2.5sqmm termination

UPS PANEL-1 A) Incomer : 1 Nos 160 AMPS,TP+2N, Microprocessor based MCCB with Manual Closing Mechanism of 25 KA Short Circuit Rating with O/L and S/C Protection and Neutral current protection with shunt coil.-1Nos B) Indication & Metering: 1 Sets of R,Y,B phase indicating lights (LED-TYPE) controlled with control 6A MCB, 1Sets of 3 phase, 4 wire,160A/5A, Digital flush type Class-I accuracy multifunction meter with RS485 modbus connectivity. 1 No. 160A/5A, Class-I, 5VA burden moulded CT's. C) Busbar: 160A, TP+2N, 25KA Cu Busbar Chamber for the entire length of the Panel as per specification 50 KA SPD ( SPD shall be with potential free contact ) TYPE-1+2 for three phase with suitable HRC fuse in the incomer & ON LED indication lamp-1No D) Outgoings : 63 Amps TP+2N TMD based MCCB with Manual Closing Mechanism of 25 kA Short Circuit Rating, with Thermal O/L and Magnetic S/C Protection -9 Nos

40KVA UPS INCOMING BREAKER 160 Amps TP+2N 25kA MCCB

NOTE CLIENT reserves to supply any listed items, the contractor shall install the same at quoted installation price CLIENT reserves to change specification and makes of materials prior to procurement by contractor All the execution shop drawings shall be prepared by vendor and approval shall be taken from Consultants/Architects/Client before execution The sample of material used shall be provided by vendor as required for approval of Consultants/Architects/Client before procurement Incase any item required for quality execution is not included in tender BOQ, the same can be added by vendors with information to consultants, architects & Client If any items mentioned in BOQ/Specification has an inmpact on delivery for completion of project with respect to time lines mention in contract, shall be informed to Architects/Consultants / Client and take an approval for alternate make. All the cable and wires used in the project shall be FRLS

DISTRIBUTION BOARDS

Supply, Installation, Testing and Commissioning of MCB Distribution board as per approved installation dwgs. Reference Standard: IS 8623 Enclosure:1.2mm CRCA Sheet Steel, Powder Coated DB type: Horizontal, 7 Segment for UPS DB's, Lighting, Emergency Lighting & Raw power or as specified. Door : Double Door Protection : IP 42 Cable Entry : Top & Bottom For UPS distribution RCCB shall be harmonic resistant (SI Series) Bus bar : Shall be tinned Copper and 200% rating for UPS DB Neutral Link MCB's : 10kA 'C' Curve for Lighting & Raw power, 10kA 'D' Curve for UPS Distribution Note: 1) Separate Earth bus & Neutral bus for each phase 2) Each Circuit shall have yellow ferrules with circuit number. 3) Accessories required for installation of DB's on Wall/Column/Gyp Board shall be considered 4) DB's shall be covered with powder coated (paint should match with DB Color) wire ways all around and up to ceiling to receive incoming circuits, how ever raceway shall be considered as a separate items & same shall be paid under raceway item. 5) Laminated A3 OR A4 size SLD & Control drawing copy shall be pasted inside DB door 6) Safe shroud for Neutral link shall be provided 7)All MCB's & Isolators should have provision for LOTO using Padlocks.

DB -8 Way TPN DB

Supply, erection, testing and commissioning of MCB DB double door type, IP 42 powder coated 8 Way TPN DB comprising of "C" curve MCB's Incomer 1 No - 80 Amps 4P 30mA RCCB Outgoings 7NOS - 6A SP 10kA "C" curve MCB 10NOS - 16A SP 10kA "C" curve MCB 7NOS - 25A SP 10kA "C" curve MCB Including all interconnections & accessories etc as reqd

DB -8 Way TPN DB

Supply, erection, testing and commissioning of MCB DB double door type, IP 42 powder coated 8 Way TPN DB comprising of "C" curve MCB's Incomer 1 No - 80 Amps 4P 30mA RCCB Outgoings 5NOS - 6A SP 10kA "C" curve MCB 9NOS - 16A SP 10kA "C" curve MCB 10NOS - 25A SP 10kA "C" curve MCB Including all interconnections & accessories etc as reqd Supply, erection, testing and commissioning of MCB DB double door type, IP 42 powder coated 8 Way TPN DB comprising of "C" curve MCB's Incomer 1 No - 80 Amps 4P 30mA RCCB Outgoings 4NOS - 6A SP 10kA "C" curve MCB 13NOS - 16A SP 10kA "C" curve MCB 7NOS - 25A SP 10kA "C" curve MCB Including all interconnections & accessories etc as reqd

DB -12 Way TPN DB

Supply, erection, testing and commissioning of MCB DB double door type, IP 42 powder coated 12 Way TPN DB comprising of "C" curve MCB's Incomer 1 No - 80 Amps 4P 30mA RCCB Outgoings 8NOS - 6A SP 10kA "C" curve MCB 18NOS - 16A SP 10kA "C" curve MCB 10NOS - 25A SP 10kA "C" curve MCB Including all interconnections & accessories etc as reqd

DB -8 Way TPN DB

Supply, erection, testing and commissioning of MCB DB double door type, IP 42 powder coated 8 Way TPN DB comprising of "C" curve MCB's Incomer 1 No - 80 Amps 4P 30mA RCCB Outgoings 6NOS - 6A SP 10kA "C" curve MCB 10NOS - 16A SP 10kA "C" curve MCB 8NOS - 25A SP 10kA "C" curve MCB Including all interconnections & accessories etc as reqd

DB -4 Way TPN UPSDB

Supply, erection, testing and commissioning of MCB DB double door type, IP 42 powder coated 4 Way DB comprising of "D" curve MCB's for UPS DB. Incomer 1 No -63A TP MCB+2N Outgoings 11NOS - 10A SP 10kA "D" curve MCB 1NOS - 16A SP 10kA "D" curve MCB Including all interconnections & accessories etc as reqd

DB -6 Way TPN UPSDB

Supply, erection, testing and commissioning of MCB DB double door type, IP 42 powder coated 6 Way DB comprising of "D" curve MCB's for UPS DB. Incomer 1 No -63A TP MCB+2N Outgoings 15NOS - 10A SP 10kA "D" curve MCB 3NOS - 16A SP 10kA "D" curve MCB Including all interconnections & accessories etc as reqd

DB -8 Way TPN UPSDB

Supply, erection, testing and commissioning of MCB DB double door type, IP 42 powder coated 8 Way DB comprising of "D" curve MCB's for UPS DB. Incomer 1 No -63A TP MCB+2N Outgoings 23NOS - 10A SP 10kA "D" curve MCB 1NOS - 16A SP 10kA "D" curve MCB Including all interconnections & accessories etc as reqd

SWITCH & SOCKETS

Supply, Installation, Testing and Commissioning of the following Modularsockets with modular front plate, with suitable MS/PVC back box accessories as per the site conditions. Refer Standard: BS 1363, IS 3864, IS 1293 Terminal : Phosphor bronze Enclosure for Current carrying part; Thermoplastic/ABS plastic complying to environment recycling Frontplate: Thermoplastic /Polycarbonate complying to environmental recycling IP Class for Modular sockets: IP20 Note: Safety shutters to prevent accidental contact with live parts shall be provided. No indicator shall be provided for switches

Supply, Installation, testing and commissioning of 3 Nos 6/10A Socket controlled by 16A switch for (UPS power) applications

Supply, Installation, testing and commissioning of 2 Nos 6/10A Socket controlled by 16A switch for (UPS power) applications

Supply, Installation, testing and commissioning of 1No 16A Socket controlled by 16A switch for (RAW Power) applications

Supply, Installation, testing and commissioning of 1No 16A Socket for (UPS Power) applications For OHP

Supply, Installation, testing and commissioning of 1No 16A Switch for (UPS Power) applications For OHP

Supply, Installation, testing and commissioning of 1No 6A Socket controlled by 6A switch for (RAW Power) applications

Supply installation testing and commissioning of module modular metal back box for data, with necessary cutting chipping works, closing the same and making the wall/ floor strong, smooth finish.

3Module modular metal back box for VOICE

3Module modular metal back box for DATA

6A Switch 1W - 1 Module with ‘Light’ Marking

6A Switch 1W - 1 Module with ‘Fan’ Marking

Blank Plate - 1M

FLUSH MOUNTING BOXES (GI)

Flush Box - 1/2 Module

Flush Box - 3 Module

Flush Box - 4 Module

Flush Box - 6 Module

Flush Box - 8 Module

Flush Box - 12/16 (2 row x 6) Module Metal Box

SURFACE MOUNTING BOXES (PLASTIC)

Surface Box - 1/2 Module

Surface Box - 3 Module

Surface Box - 4 Module

Surface Box - 6 Module

Surface Box - 8 Module

Metal Surface Box - 12/16 (2 row x 6) Module

LIGHT FITTING ,AC & FAN

Supply, Installation, Testing and Commissioning of Light fixtures and lamps with all accessories, fixing on the wall / ceiling/false ceiling with wooden blocks, screws ,hardware's ,suspended chain hooks as required as per the site conditions (including the earthing of fixture) Ballast: Electronic ballast THDshall be ≤10% Lamp type: LED color rendering index: >85 Color temprature: 6500K or as specified in respective line items Glare Index ≤ 19 Uniformity shall be 70% over 95% of the area. (350 lux @ 750mm level) Enclosure:CRCA sheet steel epoxy powder coated with antistatic treatment. Fixture shall be prewired up to terminal block with loopin-loopout facility IP Class:IP20 Note* 1. Mounting height shall be 2.7m from FFL in all areas. Suspension support height to be considered accordingly. 2. Dialux report to be shared for our review. 3. Mock up of light fixture to be done and necessary approval to be obtained before procurement.

9W WALL LIGHT FITTING WITH HOLDER

20W TUBE LIGHT

18W RECESSED DOWN LED LIGHT

MIRROR LIGHT

CEILING FAN

AC Exhaust Fan 375mm (15”) Sweep (Light Duty)

48” Ceiling Fan 5 Star Rated (1200MM)

Stepped Electronic Square Type Fan Regulator

WIRING & CONDUITS

NOTE CLIENT reserves to supply any listed items, the contractor shall install the same at quoted installation price CLIENT reserves to change specification and makes of materials prior to procurement by contractor All the execution shop drawings shall be prepared by vendor and approval shall be taken from Consultants/Architects/Client before execution The sample of material used shall be provided by vendor as required for approval of Consultants/Architects/Client before procurement Incase any item required for quality execution is not included in tender BOQ, the same can be added by vendors with information to consultants, architects & Client If any items mentioned in BOQ/Specification has an inmpact on delivery for completion of project with respect to time lines mention in contract, shall be informed to Architects/Consultants / Client and take an approval for alternate make. All the cable and wires used in the project shall be FRLS

WIRING AND CONDUITS

Supply, Laying, Testing and Commissioning of copper wires, including termination on both ends with copper lugs in existing Wire ways/Conduits/Flexible Specification: IS 694 Installation : IS 732 Voltage Grade:660/1100V Conductor: Multistrand Copper Insulation: FRLS PVC Outrsheath: FRLS PVC for multi core cables Note: 1) There shall not be any joints except at the equipment end. 2) Individual UPS and Raw power points shall have yellow ferrules for circuit identification.

POINT WIRING

NORMAL LIGHTING/FAN

SITC OF 2 x 2.5sqmm + 1 x 1.5sqmm(earth) FRLS stranded copper conductor wires in 20mm dia FRLS PVC conduits For Lighting/fan circuit Mains From respective DB to First switch board as per Layout / SLD.( Including 20mm dia FRLS PVC conduits)

SITC OF 2 x 2.5sqmm + 1 x 1.5sqmm(earth) FRLS stranded copper conductor wires in 20mm dia FRLS PVC conduits For Lighting/fan circuit Mains from first switch board to subesquent switch boards as per Layout/SLD.( Including 20mm dia FRLS PVC conduits)

SITC OF 3 x 1.5sqmm (With earth) FRLS stranded copper conductor wires in 20mm dia FRLS PVC conduits For switch borad to Lighting/fan (Including 20mm dia FRLS PVC conduits)

RAW POWER-WORKSTATION

SITC OF 2 x 4.0sqmm + 1 x 1.5sqmm(earth) FRLS stranded copper conductor wires in Raceway / 20mm dia FRLS PVC conduits For First 6/16A Power Sockets, where ever shown in the layout / SLDdrawing circuit wiring scope shall be from From respective DB to first 6/16A power socket .For Workstation sockets

SITC OF 2 x 4.0sqmm + 1 x 1.5sqmm(earth) FRLS stranded copper conductor wires in Raceway/20mm dia FRLS PVC conduits For Second 6/16A power Sockets, where ever shown in the layout / SLD drawing looped with First 6/16A Socket ie., circuit wiring scope shall be from first 6/16A Socket to second 6/16A Power socket only. For Workstation sockets

AC POWER CONTROL

SITC OF 2 x 4.0sqmm + 1 x 1.5sqmm(earth) FRLS stranded copper conductor wires in 20mm dia FRLS PVC conduits For First 6/16A/25A Power Sockets, where ever shown in the layout / SLDdrawing circuit wiring scope shall be from From respective DB to first 6/16A/25A power socket .For AC Control

SITC OF 2 x 4.0sqmm + 1 x 1.5sqmm(earth) FRLS stranded copper conductor wires in 20mm dia FRLS PVC conduits For Second 6/16A/25A power Sockets, where ever shown in the layout / SLD drawing looped with First 6/16A/25A Socket ie., circuit wiring scope shall be from first 6/16A Socket to second 6/16A/25A Power socket only. For AC control/ODU/IDU

UPS POWER-WORKSTATION

SITC OF 3C 2.5 Sq.mm PVC insulated FRLS White Sheathed FRLS copper cable in Raceway / 20mm dia FRLS PVC conduits For computer outlet UPS circuit Mains From respective DB to First set of socket outlet as per Layout / SLD.For Workstation sockets

SITC OF 3C 2.5 Sq.mm PVC insulated FRLS White Sheathed FRLS copper cable in Raceway / 20mm dia FRLS PVC conduits For computer outlet UPS circuit mains circuit Mains from first set of socket to subesquent set of socket outlets as per Layout/SLD.For Workstation sockets

CONDUITS

Conduit Pipe 19mm (3/4”) Heavy Gauge

Conduit Pipe 25mm (1”) Heavy Gauge

Conduit Pipe 32mm (11/4”) Heavy Gauge

Conduit Tee Bend 19mm (3/4”)

Conduit Tee Bend 25mm (1”)

Conduit Tee Bend 32mm (11/4”)

Conduit Solid Bend 19mm (3/4”)

Conduit Solid Bend 25mm (1”)

Conduit Solid Bend 32mm (11/4”)

CABLE TRAY & RACEWAY

NOTE : CLIENT reserves to supply any listed items, the contractor shall install the same at quoted installation price CLIENT reserves to change specification and makes of materials prior to procurement by contractor All the execution shop drawings shall be prepared by vendor and approval shall be taken from Consultants/Architects/Client before execution The sample of material used shall be provided by vendor as required for approval of Consultants/Architects/Client before procurement Incase any item required for quality execution is not included in tender BOQ, the same can be added by vendors with information to consultants, architects & Client If any items mentioned in BOQ/Specification has an inmpact on delivery for completion of project with respect to time lines mention in contract, shall be informed to Architects/Consultants / Client and take an approval for alternate make. All the raceways, bus trunking located on floor needs to be supported with proposer accessories, Vendor to consider all the assories while quoting All Data raceways & Cable tray used in project are perforated. Maximim size of perforrations shall not be more than 5-7mm

CABLE TRAYS AND WIREWAYS

Supply and Installation of the following sizes of Cable trays suspended from the ceiling or Along the wall or in trench or on floor, Refer standard: IS 1079 & 513 Material : GI / MS Finish: for GI - Pre Galvanized for indoor & Hot dip galvanized for Outdoor (NA) Finish: for MS - For indoior only - Powder coated ( colour as per architect choice) Thickness: 2mm Type: Ladder or Perforated or Solid Rung Spacing: 300mm Rung width: 35mm Supports: Up to 300mm wide using Hi-tech Rod and above 300mm wide using MS angle supports with anticorrosive paint at an intervals of 500mm. Accessories: Couplers, Bends, Reducers, Tees, Cross junctions & End cap shall be considered. The trays installed on floor shall be mounted on 'C' clamp Please note - The suppports for the trays and raceway shall be of the same material of that of the respective trays. Further MS supports shall also be powder coated. Colour of powder coating shall be as per Architect choice please do a mock-up before procurement.

CABLE TRAYS

150 mm x 50mm GI HOT DIP Powder coated tray

300 mm x 50mm GI HOT DIP Powder coated tray

Supply & installation of threaded GI rods of various diameter and GI slotted angle of various sizes including with necessary bolts, nuts, washers, etc

RACEWAY

Supply and Installation of various sizes of GI/AL raceways in floor Refer standard: IS 1079 & 513 Material: GI/AL Floor raceways thickness 2mm thick Junction box base 1.6mm/body and cover - 3mm thick Critical room race way body/cover thickness : 2mm thick Raceways shall comprise of totally enclosed, ‘U’ type channel with welded cover . This raceways & covers shall be fabricated using proper jigs and fixtures to get consistent dimensional accuracy. The raceways shall be supplied in standard length of 2.5M / 3.0M Each length shall have overlapping extension to connect the next length. The junction boxes shall have screwed covers. GI shall be proposed where ever the false flooring is available - unless mentioned otherwise AL shall be proposed only for screed areas. - unless mentioned otherwise

Supply and Laying of various sizes of GI trunking box of 2mm thick with screwed cover and should be earthed with 14 SWG bare copper wire and bond firmly to the junction box with hardware as required. Areas where the hollow portion of two raceway meets, both ends have to be connected with 14 SWG earth wire to maintain continuity. Intersecting points also to be connected through junction boxes.

Raceways Metal / GI 100mm For DATA

Raceways Metal / GI 100mm For POWER

Supply and Laying of various sizes of Powder Coated MS Raceways For DB's (Only Drops).

Raceways Metal / GI 100mm

JUNCTION BOXES FOR DATA / POWER

Supply and Installation of GI Junction Boxes thick of following sizes with removable cover having openings on all 4 sides to lead wires out to the sockets. The trunking box shall be earthed with 14 SWG bare copper and connected to the raceway. Gap between screeded floor and junction box shall be bridged with wooden members on the sides and raised to match floor level. Long screws/ bolts to be used to cover the junction box as required. The height of the junction box shall be 50mm The junction boxes shall have screwed covers.

Coupler for joining raceways 100mm

Coupler for joining raceways 250mm

Coupler for joining raceways 350mm

Coupler for joining raceways 450mm

Charges for Screed cutting in floor for accomadating the below raceways/conduits as shown in drawing (upto 110mm width & depth of 60mm or as per the site condition - vendor to visit the site understand the present screed condition and quote accordingly) The rate shall include closing of extra gap with cement, machine cutting and making good to the original level & also cleaning the debris.(Use GI mesh as per standards to avoid cracks). Price to include for junction boxes or any other items as necessary.

EARTHING

ELECTRODES

Supply, Installation, Testing and Commissioning of the Earth pits as per standard Refer Standard: IS 3043. IE rules 1956 Electrode: Cast iron for Corrosive Soil. Galvanized Iron/Non-galvanized Steel for Non Corrosive soil Plate Electrode: Copper Application: 1) CI or GI pipe electrode for Equipment Earthing 2) Copper/GI/CI plate or tripolar for System Earthing or UPS neutral and clean earthing Note: Work Related to chipping and plastering of floor area at the ground level for providing below mentioned earth pits shall be considered in interior vendor scope. Electrical Vendor to coordinate with PMC on the location of the Earth pits. Earthpit excavation and refilling will be in Electrical vendor scope

Note: 1) Installation of pipe and plate electrode shall be carried out as per details given in IS 3043 2) Earthing connections shall be carried out as per details given in IS 3043 3) Pipe electrodes shall have 12mm drilled holes not less than 75mm from each other up to 2mtr of length from bottom to top. 4)The chamber construction shall be made as per details given in IS 3043(masonry enclosure not less than 300 x 300 x 300mm with CI/MS frame cover. 5) Funnel with wire mesh shall be provided on top for individual electrode for maintenance. 6) All copper flat should be brazed and all GI flats should be welded.

Supply, installation, testing & Commissioning of earth electrode as per IS 3043 complete with all works like excavation, refilling with soil treating media like charcoal, salt, Bentanite powder, watering the system etc. equipped with heavy duty top cover madeout of Cast iron or RCC slab 600mm X 600mm X 3.15mm. thick copper plate earth electrode with 50mm. dia GI pipe 3000 mm long for watering.

Supply, installation, testing & Commissioning of Earthing arrangements with GI Earth pipe including charcoal and salt with necessary excavation in all soils and to full depth as may be required and masonry work,re-filling the sides of foundation with excavated earth as per the standard specification and as directed by the Departmental Officers.

EARTHSTRIPS

Supply, Installation on trays/in ground/on wall/in trench etc, Testing and Commissioning of the Earth strips as per installation standard IS 3043 Strips above ground: GI Strips below groung: GI Accessories: Welding for GI/MS, Brazing for Copper, GI nut bolts for connection at eqpt end/PVC sleeves for copper strips/Epoxy Insulated mounts shall be considered

25 x 06 mm - GI flat

2.5 Sqmm CU wire for DB'D Body Earthing

Supply, installation of earth bus link comprising of 25x6 GI with 10 Nos holes with SS bolts, nuts and washers. This shall be installed on insulated hylam supports & the Earth Bus should be enclosed with MS BOX, Rate shall be inclusive of the BOX & fixing accessories as required as per site condition.

SAFETY ACCESSORIES

AC Chargeable Emergency Lamp 2 x 11W PL Lamp with all connected accessories

2m x 1m Rubber Mat suitable for 11 KV installation confirming to IS

First Aid Box complete with all First Aid Medicines

Shock Treatment Chart fixed in glass frame

4 Nos. Fire Buckets made out of 40 x 40 x 6mm MS Angle

Metallic Danger Board as required by the Electrical Authorities

Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms

Earth Discharge Rod

Over Head Tank - 50KLD

Bored cast in situ piles Installation of vertical cast in situ bored piles of following dia using design mix of grade M 40 concrete (using hard broken stone graded chips of size 20mm and less) by setting the bored cast in situ pile equipments with all acccessories and tools at each of locations based on the sequence of operations as directed by the Engineer-in-charge, boring for the piles from ground level in all soils to the required depth below cut off level to carry a safe working load not less than specified using transit bore mud circulation method (using bentenite clay of required density) inclusive of pile driving accessories, temporary casing pipe, bentonite solution of 10% of concrete with required specific density, mobilisation, transferring, installation of pile driving accessories from one location to another, removal of mud from site upto a distance of 5km as directed by the departmental officers, the cost of shoe and length of pile to be embedded in the pile cap but excluding cost of steel and fabrication of reinforcement grills etc., complete complying with relevant standard specifications and as directed by the departmental officers. [The length of pile shall be measured from the top of shoe to the bottom of pile cap].

500mm dia

Chipping of RCC pile head of following dia pile to the required cut off level and clearing away the debris from site with an average lead of 5km etc., complete complying with relevant standard specifications and as directed by the departmental officers.

500mm dia

Earth work excavation for foundation in all soils and sub-soils to the required depth as may be directed except in hard rock requiring blasting but inclusive of shoring, strutting, and bailing out water wherever necessary and refilling the sides of foundation with excavated earth in 150mm thick layers well watered rammed and consolidated and depositing the surplus earth in places shown clearing and levelling the site with an initial lead of 10 metres and lift as specified here under etc. complete in all respects complying with relevant standard specifications. (Including Refilling)

Supply and filling in foundation and basement with Stone dust in layers of 150mm thickness well watered, rammed and consolidated complying with relevant standard specification including cost of stone dust etc., all complete and as directed by departmental officer.

Plain cement concrete 1:4:8 (One of cement, four of sand and eight of hard broken stone jelly) for foundation using 40mm gauge hard broken stone jelly inclusive of shoring, strutting and bailing out water wherever necessary ramming, curing etc., complete in all respects complying with relevant standard specifications and as directed by the Departmental officers.

Providing and laying in position, Standardised concrete mix M-30 grade in accordance with is: 456 - 2000 using 20 mm and downgraded hard broken stone jelly for all rcc items of works namely tee, ell or rectangular beams, lintel, parapet cum drops, waist and landing slab, canophy, circular column, fin projections, sunshades, window boxing slab, slab and other similar works with minimum cement content of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser/super plasticiser) in recommended proportions as per is:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m) 7730 kg. of 20 mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10 -12 mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand for making 10m3 concrete but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing etc., and providing fixtures like fan clamps in the rcc floor/roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. the coarse and fine aggregates to be used should comply with the requirements of is standards. (no separate payment will be made by the department for the excess usage of materials).

Foundation and basement

Providing and Laying in position, Standardised concrete mix M-25 grade in accordance with is: 456 - 2000 using 20 mm and downgraded hard broken stone jelly for all rcc works namely column, column footings, plinth beam, grade beam, raft beam, raft slab etc., with minimum cement content of 350 kg/m3 and maximum water cement ratio of 0.50, including admixture (plasticiser/super plasticiser) in recommended proportions as per is :9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m) 7730 kg. of 20 mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10 -12 mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand for making 10m3 concrete but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing etc., complete complying with standard specification and as directed by the departmental officers. the coarse and fine aggregates to be used should comply with the requirements of is standards. (no separate payment will be made by the department for the excess usage of materials)

Ground Floor

First Floor

Second Floor

Third Floor

Supplying, fabricating and placing in position of Mild steel Grills / Ribbed Tor Steels of all diameters for reinforcement for all floors including cost of binding wire, bending tying etc., all complete and as directed by the departmental officers.

Providing Form work and centering for reinforced cement concrete works including supports and strutting up to 3.30m height for plane surfaces as detailed below with all cross bracings using mild steel sheets of size 90cm x 60cm and MS 10 gauge stiffened with welded mild steel angles of size 25mmx25mmx3mm for boarding laid over silver oak or country wood joists of size 10cmx6.5cm spaced at about 90cm centre to centre and supported by casurina props 10cm to 13cm dia spaced at 75cm intervals and removing the same after a specified period without damaging the R.C.C works etc., complete complying with standard specifaction and as directed by the departmental officers.

Column footings,plinth beam,Grade beam, Raftbeam,Raft slab etc.,

Plain surfaces such as Roof slab, floorslab, Beams, lintels, lofts, sillslab, staircase waist, portico slab and other similar works

Square and rectangular columns and small quantities such as sunshade, parapet cum drops window boxiing, fin projection and other similar works.

For Column upto 3.30m - 4.30m height

For Column upto 4.30m - 5.30m height

For Column upto 5.30m - 6.30m height

For Column upto 6.30m - 7.30m height

For Column upto 7.30m - 8.30m height

For Column upto 8.30m - 9.30m height

For Column upto 9.30m - 10.30m height

For Column upto 10.30m - 11.30m height

For Column upto 11.30m - 12.30m height

f.Curved surface

Special ceiling plastering in cement mortar 1:3 (One of cement and three of sand) 10mm thick for bottom of roof, stair, waist, landing and sunshades in all floors finished with neat cement including hacking the areas, providing band cornice, scaffolding, curing etc., complete

Plastering with CM 1:5 (One of cement and five of sand) 12mm thick finished with neat cement including providing band cornice, ceiling cornice, curing, scaffolding, etc., complete in all respects and complying with relevant standard specifications.

Supplying and fixing Mild Steel grills as per the design approved to verandah enclosure or gate including one coat of primer and labour for fixing in position etc. all complete

Painting the false ceilling / walls two coats with 1st class ready mixed Exterior emulsion paint of best approved quality colour and shade over a priming coat, including clean removal of dirt and dust etc., complete including cost of necessary brushes, labour charges, putty etc., complying with relevant standard specification. (The paint should be supplied by the contractors at his own cost.The quality and shade of the paint should be got approved by the Executive engineer before use.) (Outer)

Painting the new Iron work and other similar works such as PVC /ASTM Pipes, Kerb Stone and grills with two coats of approved first class synthetic enamel ready mixed paint of approved quality and brand, the paint should be supplied by the contractor at his own cost. (The quality and the brand of paint should be got approved by the Executive Engineer before use) complying with relevant Standard specifications.

Supply and delivery at site and fixing of SFRC manhole cover with frame with locking arrangement

750mm x 750mm - (M-0715)

Precast cement concrete Jally ventilator in standardised concrete mix M25 (annexure) without vibrating charges for the following thickness excluding the cost and fabrication of reinforcement grills but including precasting, moulding, curing, finishing and fixing in position complying with relevant standard specifications etc., complete in the following floors. 50mm thick

In Ground Floor

Supplying, laying and jointing G.I. Pipes of approved quality and best variety of “B” class pipe of the following dia including labour fixing G.I. Specials, (excluding charges for cutting and threading of pipes, cost of such specials) to wall with necessary teak wood plugs, clamps, screws, thread balls, shellac, etc., making holes on the walls (or) drilling holes in roof and making good the dismantled portions to original condition with neceSORay brick work / concrete and plastering wherever neceSORy with necessary scaffolding charges. The pipes are to be painted with the 2 coats of good variety and approved best quality of synthetic enamel paint over a priming coat of red oxide etc., complete in all floors complying with standard specification. G.I. pipes shall be got approved by the Executive Engineer before use on works - Internal water supply - Above Ground Level / External water supply - Above Ground Level. The rae should be included of lifting charges of pipe connection.

a) Laying pipe line of dia 65mm For Inlet Connection, Outlet, Overflow and Rain water harvesting pipes

b) Laying pipe line of dia 50mm For scour pipes

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

GI Flange set (WD-M0597)

PVC Couplers fabricated 6 KSC (WD-M0106)

G.I. Equal Tee plain (WD-M0595)

G.I. Coupling (WD-M0596)

G.I. Equal Elbow plain (WD-M0594)

PVC REDUCER COUPLER (WD-M0078 & WD-M0080)

a)75 mm x 63 mm

b)90 mm x 75 mm

65 mm x 50 mm (WD-M0509)

a) 65 mm x 50 mm

PVC Pipe (10KSC) (WD-W0981)

a) 75 mm Dia

Laying of PVC rigid pipes (WD-M1882)

a) 30000 Capacity in LPM, 20m Head in Metres

Installation, Testing & commissioning of approved make submersible Clearwater lifting pump set with suitable horse power motor to each pump to discharge with control panel & all necessary accessories, conducting trail run, providing necessary civil foundations and base frame with all accessories like pressure gauge, control valve etc., and consumables, maintaining the system for the period of one year. Rate shall include all Electrical panel work connected to existing Electrical cable arrangement, etc. complete. Incoming Electrical cable to starter panel will be under scope of Electrical work. Transfer of water from UG Sump to Over Head Water Tank.

Flow : 1.2 lps Head :16-20 MWC No. of pumps : 2 (1 working + 1 Standby) Type : Submersible Application : Clear water transfer Time : 0.50 Hours

20 KW SOLAR ONGRID POWER PLANTS

Design, Supply, Installation of 20 KW Solar Power Plant 550 W Solar Panel- 36 No’s, 15 KW on grid solar Inverter – 1 No 05 KW on grid solar Inverter – 1 No

Supply and installation of solar panel mounting structure, ACDB, DC cable connectors, with all other accessories

ELEVATION NAME BOARD & LOGO

For Academic Block & Hostel Block

AUDITORIUM - Interior

Supply and installation of Pixel 0308 perforated GFR gypsum acoustical false ceiling panels, size 1200x2400x12.5mm, 3x3mm square perforations @ 8.33mm pitch (8% open area), backlined with acoustical fleece, volume density 700 kg/m³, weight 9 kg/m². Installed using Strut ceiling framework comprising WC25 wall channels, MC45 main channels, CC25 cross channels with suspenders, finished with Seam AJC jointing compound and tape, including white primer coat. Suitable for RH up to 70%. Approved make: Anutone / Armstrong / Topakustik. Rate Should be Inclusive of Scoffolding

Supply and installation of cove light false ceiling using square edge GFR core panels of size 1200x1800x12mm, fixed on Strut ceiling framework including WC25 wall channels and necessary suspension accessories, complete as per manufacturer specifications.

Supply and installation of acoustical wall panels – Salon Slats Surco made of pinewood E1 grade fiberboard with melamine laminated finish, groove perforated slats L16-2 (2mm grooves @16mm pitch, 27% open area), backlined with Soundtex black acoustical fleece. Panels of size 128x2440x16mm, NRC 0.75, fire rating BS476 Part 7, installed on GI Strut framework with CC25 and CC18 channels, including SynthPF backlining and all accessories. Approved make: Anutone / Armstrong / Topakustik. Rate Should be Inclusive of Scoffolding

Supply and installation of 4mm thick loop pile roll carpet made of 100% nylon, fixed over existing tile flooring using approved adhesive, including aluminum profiles for step edge termination.

AUDITORIUM - Chair

ORIGIN AUDITORIUM CHAIR ORIGIN auditorium chair is a highly-functional model offering most of the accessories you might need for either informative or non-informative events. It is very competitively priced, yet maintains high quality and offers superior comfort. OUTERBACK: Injection moulded, high-impact polypropylene SEAT & BACK CUSHION: Streamlined back cushion and ergonomic seat cushion SEAT PAN: Vented polypropylene TIP-UP SEAT MECHANISM: Counterweight mechanism ARMREST: Imported hardwood armrest LEG: Strong steel structural support

COFFEE TABLE

COFFEE TABLE : 800 X 800 X 450 HIGH CENTRAL COFFEE TABLE in 18 MM with matching Pre Laminated finish ; with 10 mm toughened glass on ss studs etc as per design

VIP seating on stage

Allen Sofa set With Chrome Legs. Amazing, affordable style arrive in the form of this easy-care fabric Sofa. Constructed of high performance easy-care upholstery that is as subtle and it is durable, this couch is alluringly designed with a contemporary edge. This savvy furnishing features box spring seats that provide for sturdy comfort and is outfitted with sleek barrel shaped chrome color legs that elevate the height seating solution providing for a more modern look. Fabric Collection: Green | Brown | Blue Sofa dimensions: 700x700x450

Podium

PLB 18mm thick Podium

Transportation & Installation Charges

Auditorium - AV System

Multimedia Projector Sony PT - CWZ10

Ceiling Mount Kit

150" Motorized Projection Screen

2-Port 4K HDMI Splitter

HDMI HDBaseT Extender

HDMI/DVI to HDMI Converter

FOH Speaker JBL AM5215/95

Speaker Mounting Arrangements

Stage Monitor JBL EON 610

Power Amplifier Crown XTI6002

Digital Mixer Yamaha TF5

Wireless Microphone AKG MS470/D5

Gooseneck Microphone

HDMI 2.0 Cable 2M 1.8m

HDMI 1.4 Cable 1.8m

Speaker Cable 2C 2.5sqmm

Microphone Cable 2C

4 Pair Snake Cable

Shielded Twisted Pair Cable CAT6

Floor Plate with Back Box HDMI

All Connectors

15U Equipment Rack

Installation Charges

Auditorium - HVAC (Low Side)

Low side Air conditioning Works

Supply, Installation, Testing & Commissioning & Handing over of the following:

Sheet Metal Work with TDF Flanges for all sizes of the duct. Fabrication as per IS Standards

All duct construction and installation shall be in accordance with IS standards. In addition ducts shall be factory fabricated utilizing the following machines to provide the requisite quality of ducts.

All ducts shall be fabricated and installed in workmanlike manner, conforming to relevant IS codes.

The Duct shall be included with Guide vanes, Adjustable splitter dampers, fastners, threaded rods, nut, Fire retardent Gasket and washers as per specs and ducts supported with Hi-tech Supports at regular intervalas as mentioned in the technical specifications.

Airbalancing (Using Hood for CFM reading) and Minor civil works for wall opening and closing using sand cement Mortor as per site condition are included. GI Sheet Wastages will not be considered for final measurement.

20G up to 1501 to 2250mm

22 G up to 751 to 1500mm

24 G Up to 750mm

Supply and fixing - Al powder coated Slotted Diffuser for supply & Return air with out VCD, including necessary GI Sreq, bolt, nut & supports. The BOX Channel supports for the slotted diffusers shall be in the scope of interior vendor. The Slotted diffuser should be fixed to the false ceiling using 4inch tap (Water proof PE coated fabric Tap withy thick of 0.26mm+/- 10%) to ensure Zero leakage before fixing diffuser at false ceiling.

Supply and Fixing - Hitt & Miss Damper - G.I.Powder Coated (18G) , Collar Dampers of opposed blade type made out of Aluminium alloy extrusion with anodised matt black finish, including necessary GI Sreq, bolt & nuts.

Supply and fixing of multiblade Opposed type Volume control damper constructed out of 18G GI damper with suitable links,and nylon bearings with quadrants and levers for manual control of volume flow of air for proper distribution and balancing of the system with lever locking facility, including necessary GI Bolt, nuts & washers.

Supply and Fixing - Motorized Dampers -Opposed type constructed out of 16G GI damper with suitable links,and nylon bearings with quadrants and levers for manual control of volume flow of air for proper distribution and balancing of the system with lever locking facility, with extended rod for fixing actuator, including necessary GI Bolt, nuts & washers.

Supply and Fixing -Spring return Actuator for Motorized damper Dampers including step down transformer. The Actuator Torque shall be suitable to the Damper size.

Supply, laying & termination of 3C x 2.5sq.mm power wiring between Actuator to DX unit Starter panel, with necessary supports & clamps.

Supply, laying & termination of 3C x 1.5Sq.mm power cabling between 230V single phase power socket to Actuator with necessary supports & clamps.

Supply & fixing of 16G M.S.Conduit for cable laid between actuator to AHU panel

Supply Fabrication , and erection of Double canvas connection made out of fire retardent canvas cloth with Zip required necessary fixing arrangements including nuts & bolts Etc

Supply & Fixing of Insulated Flexible Ducting

Factory Fabricated Insulated Flexible duct for connecting from main duct to diffuser box with Grip clamp. The length of the flexible duct shall be around 1.0 to 1.8 mtr

The flexible duct shall me made of triple lamination of aluminium foil, polyester and metalised polyester film permanently bonded to a coated spring steel wire helix. The exterior shal be wrapped with 25mm thick 16 kg / cum fibreglass insulation. The outer insulation jacket / vapour barrier made of fibreglass reinforced metalised polyester film laminate.

250 mm dia

300 mm dia

Supply & fixing of Thermal insulation for supply air duct using 9mm thick class " O " Closed cell nitrile rubber based elastomeric insulation with the density of 40 - 55 kg /m³ .

Supply & fixing of Acoustic insulation for Supply air duct using 10 mm thick class 1 rating Open cell nitrile rubber elastomeric insulation with density of 140 - 180 kg / m³.

Supply & fixing of 16G M.S.Conduit & cable laid between indoor to outdoor unit

Auditorium - VRV Outdoor Units

Supply, Lifting, Installation, Testing & Commisioning of Inverter /Digital scroll compressor with Variable refrigrant system connectable to multiple indoor units. Outdoor unit shall be factory assembled weather proof casing constructed from heavy gauge mild steel panels. The unit shall be completely factory wired and tested with necessary controls and charged with refrigerant. The compressor shall be highly efficient scroll type. The aluminium fins of outdoor unit shall be covered with anti-corrosion resin. Unit shall be equipped with oil recovery system to ensure stable operation with long refrigrant piping. Units shall be tested and commissioned with additional refrigerant.The unit shall be compatible for Third Party BMS Integration. Neccessary relay card /soft integrator to be provided, Outdoor unit shall be provided with vibration isolators and firmly grouted to civil pedestals.

22HP ODU

VRV Indoor Units

Supply of Indoor Units shall be Ducted Ceiling Suspended as specified. The indoor unit shall have independent electronic control valve to control the refrigrant flow rate respond to variations of the airconditioning load of the room. The fan shall be aerodynamically designed turbo multiblade type. Statically and dynamically balanced to ensure lowest noise. The cooling coil shall be made of seamless copper tube. The tube shall be hydrolically or mechanically expanded and tested for 21 Kg/cm2. Indoor units shall have prefilters and wireless remote control. With necessary supports for indoor units.

11TR Ductable Unit

Supply & Installation of Refnet Joints

Supply and Installation of 18G Copper Refrigerant Piping with necessary fittings, Y Joints and headers, insulated with19mm thick elastomeric nitrile rubber insulation and wrapped with polyshield coating between indoor & outdoor units as per specifications. Scope includes pressure testing of refrigerant pipes and Refrigerant Gas charging. All piping inside the room shall be properly supported with hanger and all external piping shall run in covered cably tray. Minor civil works like wall opening and closing for copper piping are included.

31.75 mm dia

28.57 mm dia

25.4 mm dia

22.22 mm dia

19.05 mm dia

15.87 mm dia

12.7 mm dia

9.53 mm dia

Supply & installation of Ladder type G.I. tray, covered with G.I.Sheet for copper pipes and cables

150mm wide

Supply & Laying of High Density PVC drain pipe with 9mm thick Nitrile rubber tubular pipe insulation with necessary supports.

Supply,Laying & Termination of 2C x 1.5sq.mm Transmission cable between IDU to ODU & ODU to CRU unit with Necessary supports, screws, etc.

Supply & fixing of 25mm MS conduits complete with all fittings & accessories with Necessary supports, screws ,etc.

Supply, laying & termination of following cable from Isolator to VRF Outdoor unit and from 10Amps power socket to indoor units with necessary supports and PVC flexible hose, etc.. ( Isolator & power sockets to be provided by Electrical Vendor including the suitable cable upto isolators & sockets.)

3C x 2.5Sqmm copper Armoured cable

3.5C x 50Sqmm copper Armoured cable

Supply, laying & termination of following cable from Isolator to VRF Outdoor unit and from 10Amps power socket to indoor units with necessary supports and PVC flexible hose, etc.. ( Isolator & power sockets to be provided by Electrical Vendor including the suitable cable upto isolators & sockets.)

3C x 2.5Sqmm copper Armoured cable

4R x 25Sqmm copper flexible cable

AIR CONDITIONERS - ACADEMIC BLOCK

SUPPLY & INSTALLATION OF AIR-CONDITIONER WITH COPPER COIL

1.5 TR Split Type AC Unit - 3 Star Rated (M-1986)

Supply and installation of 5 KVA capacity Automatic Voltage Stabilizer with time delay relay (M-1989)

Supply and fixing of MS stand for fixing outdoor unit (M-1991)

Supply and laying of 5/8” and 3/8” copper pipe (Extra beyond 3 metres supplied with AC unit) (M-1990)

AIR CONDITIONERS - HOSTEL BLOCK

SUPPLY & INSTALLATION OF AIR-CONDITIONER WITH COPPER COIL

1.5 TR Split Type AC Unit - 3 Star Rated (M-1986)

Supply and installation of 5 KVA capacity Automatic Voltage Stabilizer with time delay relay (M-1989)

Supply and fixing of MS stand for fixing outdoor unit (M-1991)

Supply and laying of 5/8” and 3/8” copper pipe (Extra beyond 3 metres supplied with AC unit) (M-1990)

Please Enable Macros to View BoQ information