CONSTRUCTION OF 50 BEDED HOSTEL AT RESIDENTIAL UPGRADED HIGH SCHOOL HUNTH BLOCK ARKI

Earth work in excaviation in foundation trenches in ordinary soil (vide classification of soil item A) & disposal of excaviated earth as ovrained to a distance upto 50 mnincluding all lifts, levelling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approve design, building specification & direction of E/ incharge5.1.1

Extra for earth work in hard soil as per specification and direction of engineer incharge(vide classification of item B)5.1.2

Earth work in filling in sub floor trenches and plinth in layersnot exceeding 150 mm thick, well watered, rammed, fully conpared and fine dressed with earth obtained after cutting within lead of 50m and lift of 1.5m all completed as per direction of the E/I( mode of measurement compacted volume).5.1.7

Providing coarse clean sand in filling in foundation trecches or in plinth including rammingamd watering in layers not exceeding 150mm. Thick with all leads and lifrs including cost of all materials, labours, royality and taxes all complete jobs as per building specification and direction of the E/I . ( mode of measurement compacted volume) 5.1.10

Providing degination 75B one brick flat soiling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of the E/I.5.6.3

Providing and laying in position cement concrete of specified grade excluding the cost the cost of centering and shuttering all work up to plinth level(1:3:6)5.3.1.4

Providing and laying in position cement concrete of specified grade excluding the cost the cost of centering and shuttering all work up to plinth level(1:2:4)5.3.1.3

Providing and laying in position reinforced cement concrete of soecified grade excluding the cost the cost of centering and shuttering all work up to plinth level(1:1.5:3)M205.3.9.1

Providing cement concrete works in walls including attached pilasters butteress plinth and string courses fillets columns pillars piers abutment post and struts etc. above plinth level upto floor five level rxcluding cost of centering shuttering finishing and reinforcement: (1:1.5:3) M205.3.10

Providing reinforcement concrete work in beam suspended floors roofs having slope upto 15 degree landing balcony shelves do.. Do.. As per E/I. (RCC M20)5.3.11

Providing,hoisting and fixing above plinth level upto floor five level precast Reinforced cement concrete shelves including setting in cement mortar 1:3( 1 cement :3 coarse sand)-do-. 5.3.20

Providing Tor steelreinforcement as per approved design & drawing.5.5.4

Providing Tor steelreinforcement of 10 mm dia bar as per approved design & drawing.5.5.5(a)

Providing Tor steelreinforcement of 12 mm dia to 20 mm dia bar as per approved design & drawing.5.5.5(b)

Centering including struting , proping etc and removal form for5.3.17 Foundation footing bases for column etc.5.3.17.1

Column, piers ,Pillars etc5.3.17.6

Lintel beams ,plinthbeam etc.5.3.17.5

Suspended floors ,roof, landing balconies etc.5.3.17.3(v)

Weather Shade,Chajjas,corbels etc.5.3.17.19

Stairs (excluding landings) except spiral staircases etc.5.3.17.7

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding,top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. DSR 10.18

Providing desination 75B brick work in cement mortar (1:6) in foundaton & plinth with approved quality of clean coarse sand of F.M 2 including providing 10mm th.mortar joints cost of screning materials, racking out joints to 15mm depth, curing, taxes and royalty all complete as per build specification and direction of E/Incharge.5.2.6

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).BCD(5.3.5)

Providing desination 75B brick work in cement mortar (1:6) in SUPER STRUCTURE with approved quality of clean coarse sand of F.M 2 including providing 10mm th.mortar joints cost of screning materials, racking out joints to 15mm depth, curing, taxes and royalty all complete as per build specification and direction of E/Incharge.5.2.14

Providing designation 125MM thick reinforced brick work with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/IBCD(5.2.23)

Providing 6mm, cement plasters (1:4) in ceiling with clean coarse sand of F.M 1.5 including cost of carriage, screening , curing with all lead and lifts of water, scaffolding taxes and royalty all complete as per buiding specifications and diarection of the E/I.5.7.6

Providing 12mm. Cement plaster (1:4)lwith clean coarse sand of F.M .15. including cost of carriage, screening, curing with all lead and lifts of water,scaffolding, taxes and royalty all complete as per building specifications and direction of the E/I. 5.7.2

Providing 12mm. Cement plaster (1:6)l with clean coarse sand of F.M .15. including cost of carriage, screening, curing with all lead and lifts of water,scaffolding, taxes and royalty all complete as per building specifications and direction of the E/I. 5.7.3

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. DSR 13.80

Providing two coats of Oil bound distempring of approved shade and make over a coat of cement primer over new surface do…do… as per E/I.5.8.18

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) DSR 13.47.1

Providing and laying Double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622/ ISO 13006, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. complete Size of Tile 600 x 600 mm5.6.28

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement:4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. DSR 11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size 11.41A.3.1 Size of Tile 600 x 600 mm

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I. WITH COMMERCIAL GRADE COLOUR TILES. BCD 5.6.23.4

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick. DSR 11.26.1

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. DSR 11.27

Providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm DSR 8.2.2.2

Providing and laying flamed finish Granite stone flooring in required design And patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. DSR 11.55.1

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : Medium shade pigment using 50% white cement, 50% ordinary cement. DSR 11.19.2

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade. DSR 8.10.2

Supplying , fitting and fixing M.S grill made of 20 X 6mm. M.S flat/ square bars as per approved design & drawing, properly fibricated with joints contiuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. 5.5.12

Supplying,fitting and fixing callapsible gate of approved size and make properly fabricated with vertical double channels 20X'10X2 mm. at 100mm. Centres and braced with M.S. flat diagonals 20 X 3mm, with top and bottom rails of T. iron 40x40x6mm with 38 mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification arrd direction E/I.BCD 5.5.14

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge,(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.). DSR 10.28

Painting with synthetic enamel paint of approved shade and mnufacture do…do… as per E/I.5.8.41

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.BCD(5.8.45)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :Powder coated aluminium (minimum thickness of powder coating 50 micron) DSR 21.1.1.2

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron) DSR 21.1.2.2

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) DSR 21.3.1

Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylight, fanlights and C/W celetial windows openings, including wedge over all clamps complets including application of two coats of wood preservative of approved quality on the surface butting walls and lintels complete as per building specification and direction of E/I. BCD 5.4.1

Supplying, fitting and fixing 35mm thick solid core type non decorative single leaf flush door shutters in doors and windows with black board core bended with high quality phenol formal dehydes synthetic resin both side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I. BCD 5.4.38

Supplying, fitting and fixing 35mm thick solid core type non decorative double leaf flush door shutters in doors and windows with black board core bended with high quality phenol formal dehydes synthetic resin both side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I. BCD 5.4.39

Providing & Fixing decorative high pressure laminated sheet of plain /wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick . DSR 9.127.1

Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters (bathroom and W.C. doors) using synthetic rubber based adhesive. DSR 9.125

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. DSR 22.5

Water proofing for old and new Roof slab:-Providing and layind water poroofing treatment on roof slab by applying two component factory a designed ready to use5.12.1surface preparation-providing and cleaning of concrete surface.(a)1st coat-apply 1st coat of two component acrylic modified redy to use …(b)2nd coat-apply 2nd coat of two component acrylic modified redy to use …©Protection of treated PCC -the treated surface shourd be covered with 25/50 mm pcc of M20.(d)Groove of PCC surface should be filled with polysulfide sealant.(e)

Covering with treated surface with PCC Providing 25 mm thick C.C. M20 do…do… as per E/I.5.12.2

Providing and fixing of 6 mm thick groove between 25 mm PCC panels with Polysulphide sealent pouring grade as per drawing and technical specifications. BCD 5.12.8

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 MM DIA. DSR 12.41.2

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 110 MM DIA. DSR 12.42.5.2

shoe plain 110 MM DIA. DSR12.42.6.2

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length,including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete. 110 MM DIA. DSR12.43.2

Making plith protection 50 mm thick of cement concrete 1:3:6 over 75 mm thick bed of dry brick blast do.. Do as per E/I.5.3.8

Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I. BCD 5.10.33

Carriage of materials: Bricks

stone chips

cement

steel

metal

Point wiring in PVC conduit with piano type switch Wiring for light point /call bell point / exhaust fan point with 1.5 sqmmFRPVC insulated coper conductor single core cable in surface / recessed PVC conduit with paino type switch phenolic laminated sheet with suitable size of Msbox and erthing the point with 1.5 sq mm FRPVC insulated copper conductore single core cable etc as required Group C 1.3.3

S/F/F Light plug point with modular type accessories-supplying and fixing suitable size GI/PVC box on surface or in recess with phenolic laminated sheet cover including p/f 5 pin,5/6 amps piano socket outlet and 5/6 amps piano type switch . 1.31

S/F/F Light plug point with modular type accessories-supplying and fixing suitable size GI/PVC box on surface or in recess with phenolic laminated sheet cover including p/f 5 pin,15/16 amps piano socket outlet and15/16 amps piano type switch . 1.32

power plug Wiring in pvc conduit 2x4 sq mm wiring for light /power plug with 2x4 sq mm frpvc insulated copper conductor single core cable for loop earthing as required.1.5

Wiring for circuit /submain wiring alongwith earth wire with the follwing sizes of FRPVC Insulated copper conductor single core cable.1.7 2x1.5 sqmm +1x1.5 sqmm earth wire.1.7.1

2x2.5 sqmm 1x2.5 sqmm earthwire.1.7.2

4x10 sqmm+1X10sqmm earthwire.1.7.5

4x6 sqmm +2x6 sqmm earthwire1.7.10

Wiring in existing conduit - Supplying and drawing following sizes of FR PVC insulated copper conductor,single core cable in the existing surface/recessed steel/pvc conduit as required. 2x4 sqmm 1.15.20

S/F four pole MCB Isolator-supplying and fixing following rating four pole 415 volts,isolator in the existing MCB DB complete with connections,testing and commissioning etc as requird. 40 amps. 2.15.1

S/F four pole MCB Isolator-supplying and fixing following rating four pole 415 volts,isolator in the existing MCB DB complete with connections,testing and commissioning etc as requird. 80/100 amps. 2.15.3

S/F/F SP. MCB DB - Supplying and fixing following way single pole neutral sheet,MCB distribution board 240 volts on surface /recess, all complete. 8 way double door. 2.8.8

S/F TP MCB DB- Supplying and fixing following way,three pole and neutral sheet MCB distribution board 415 volts,on surface/recess all complete. 2.9 4 way (4+12),Double door,Horizontal type 2.9.4

6 way (4+18),Double door,Horizontal type. 2.9.5

S/F 'C' series MCB - Supplying and fixing following 240 v 'C' series,miniature circuit breaker suitable for inductive loads of following poles all complete. 2.12 6/32 amps,single pole

40 amps TPN

40 amps DP

50/63 amps,DP

S/F ceiling rose- supplying and fixing 2 pin 5 amp ceiling rose on the existing junction box/wooden block including connection as required. 1.33

ITC Fluorescent fittingd directly on surface - installation,testing and commissioningh of prewired flourescent fittings of all type all complete. 1.41

ITC Fluorescent fitting with down rods - installation,testing and commissioningh of prewired flourescent fittings of all type all complete. 1.42

ITC ceiling Fan - installation,testing and commissioning of ceiling fan including wiring the down rods of standard length all complete. 1.44

Supplying and fixing following piano type switch /socket on the existing switch box/cover including connections etc as required. 1.23 5/6 amps one way switch 1.23.1

3 pin 5/6 amps socket outlet 1.23.4

Electronic step fan Regulator 1.23.9

S/f PVC /GI box of following sizes on surface or in recess with suitable size of phenolic laminated sheet cover etc. as required. 75mmx75mmx50mm deep. 1.22

ITC of Exhaust fan upto 450 mm sweep in the existing opening, including making the hole to suit the size of the fan all complete as required. 1.49

S/F of following sizes of PVC conduit along with accessories in surface/recess including cutting wall etc. as required. 20 mm 1.21.1

S/F batten holder including connections etc. as required. 1.34

Earthing with copper earth plate 600mmx600mm x3mm thick including accessories and providing masonary encloser with cover plate.3.6

P/F 8 SWG dia copper wire at 0.50 m below ground level for conductor earth as required.3.7

P/F 25 mmx5mm G.I strip in 40 mm dia. GI pipe from earth electrode including connections as required. 3.9

P/F GI lightning conductor finial made of 25 mm dia. 300 mm long copper tube all complete as required. 4.2

Reverting,sweating and soldering of copper/GI tape as required. 4.4

Providing and fixing GI tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as required. (Horizontal run) 4.7

Providing and fixing GI tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as required. (Vertical run) 4.8

Supply of ISI marked aluminium cable conductor XLPE PVC insulated cable all complete. M-329

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 185 mm all complete. 5.12

Supplying and fitting of 1400 mm sweep regular/standard model AC fan including connections all complete. 9.4.2

SITC of 300 mm (12")Exhaust fan for single phase 230 v 50 HZ.JSR M774

Supply and fitting of 380 mm,230 V AC metal Exhaust fan in the existing opening all complete. M-776

Supply and fixing of wall mounted LED 20w/22w Tube batten electronic driver and accessories as required. 9.5.2

Supply and fixing of wall mounted LED 9w/10w bulb and accessories as required. 9.5.2

S/F/F flood light 100 w with accessories. 9.2.4

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I. 'p' trap 15 litres C.I. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware footrest to be fixed in floor 15mm C.I. body brass spindle stop cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and dirction of E/I. 580mm long - With 12.5 liter low level PVC cistern3.2.1

Supplying and fixing 40 mm high white vitreous glazed (European type W.C. pan) with p trap seat and lid, 15 litre low level white P.V.C. flushing cistern with manually controlled devicde (handle lever), conforming to IS:7231, parryware/Hindware/with all fittings and fixtures complete including cutting and making good the walls and floors wherever required. 3.2.2(b) with 10 litre Pvc citern

Supplying,Fitting and fixing viterous white glazed earthen ware wash hand basin of parry Hindustan or any other I.S.S. approved make all complete. 3.2.5

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board : 510x1040 mm bowl depth 178 mm. DSR 17.10.1.4

Supplying,Fitting and fixing flat back or angular lipped front viterous white glazed earthen ware Urinal(600mmx350mm) of parry Hindustan or any other I.S.S. approved make all complete. 3.2.3

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore . DSR 18.49.1

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore. DSR 18.51.1

Providing and fixing PTMT soap Dish Holder having length of 138mm,breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106 gms. DSR 18.65

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore. DSR 18.53.1

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 15 mm nominal bore, weighing not less than 32 gms. DSR 18.75.1

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Circular shape 450 mm dia. DSR 17.32.1

Providing and fixing PTMT grating of approved quality and colour. Circular type :125 mm nominal dia with 25 mm waste hole .DSR 18.58.1.2

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length. DSR 18.74.2

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia. DSR 17.28.2.1

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. DSR 18.8 15 MM DIA. 18.8.1

20 MM DIA. 18.8.2

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work DSR 18.9 25 MM DIA. 18.9.3

32 MM DIA. 18.9.4

40 MM DIA. 18.9.5

Supplying all materials with labour for construction of inspection chamber of designation class 75 B brick deep 600x450 internal dimension having 250 mm wall thickness all complete. 3.3.8

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore . DSR 18.52.1

Polythene water storage tank of ISI mark with cover & locking system. M-079

Providing and fixing PTMT towel rail trapezoidal shape 215 mm long,200 mm wide all comp. 3.1.21 c(i)

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long,200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms. DSR 17.72

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes. 110 mm diameter. DSR 12.41.2

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes. 75 mm diameter. DSR 12.41.1

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. DSR 12.42 75 MM COUPLER 12.42.1.1

110 MM COUPLER 12.42.1.2

75 MM SINGLE PUSHFIT COUPLER 12.42.2.1

110 MM SINGLE PUSHFIT COUPLER 12.42.2.2

75 MM SINGLE TEE WITH DOOR 12.42.3.1

110 MM SINGLE TEE WITH DOOR 12.42.3.2

75 MM SINGLE TEE WITHOUT DOOR 12.42.4.1

110 MM SINGLE TEE WITH0UT DOOR 12.42.4.2

75 MM BEND 87.50 12.42.5.1

110 MM BEND 87.50 12.42.5.2

75 MM SHOE PLAIN 12.42.6.1

110 MM SHOE PLAIN 12.42.6.2

Providing and laying in position cement concrete of specified grade (1:4:8) BCD 5.3.1.6

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs,conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.100 mm nominal size dia. DSR 23.4.1

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. DSR 23.5

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. DSR 23.6

Supplying and fixing C.I. cover without frame for manholes :500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg. DSR 19.18.2

Cost of drilling 200mm x165mmx125 mtr dia Deep borewell : Supplying all materials labour, tools & equipments for driling 200/150 dia borewell in any kind of soil/rock by using DTH supper Rig machine and bell hammer technology inclusive of mollisation dermolisation of rig air complete job including of transportation charge up to the site -do-PHED page no-57 Item no-M-1035 From 0.00 m to 50.00m Below GI

From 51.00 m to 150.00m Below GI

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size diaDSR 23.3.3

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fullydeveloped, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc.,all as per requirement and direction of Engineer-in-charge. DSR 23.12

Supplying and fitting MS Cap over 200 mm dia casing pipe all complete job as per direction of E/IDSR 23.13.3

Supplying and fitting MS clamp all complete job as per direction of E/IDSR 23.14.3

submersible pump 100 mm dia(with bronz impeller upto 20 stage) :- 2.00 H.P. PG-66/67 M-1055

Supplying fitting and fixing of standard make starter board with arrangement of all necessary including all traxes as per E/I..M-1065 PG-77

FR PVC INSULATED 3 CORE 4 SQMM COPPER WIRE . M-1627.

S/F/F lowering 40mm dia G.I. column pipe do..do.. As per E/I.pn.-35 M930(K)-V

Providing 12 mm cement plaster (1:3) with clean coarse sand of FM 1.5 with floating coat of neat cement in skirting all complete. BCD 5.6.10

Providing 12 mm cement plaster (1:3) with clean coarse sand all complete. BCD 5.7.1

Providing 1.5 mm cement punning including curing,carriage of water all complete. BCD 5.7.11

Making soak pit 2.5 m diameter 3.0 m deep with 45x45 cm dry brick honey comb shaft with bricks all complete. DSR 19.32.1

Add 18 % GST

Add 1% Labour Cess

Please Enable Macros to View BoQ information