Installation of Fire Doors in New Judicial Complex Tower of Justice at Gurugram Detailed estimate for fire fighting system in Multi Level basement Parking in the Campus of New Judicial Complex Tower of Justice at Gurugram (RECALL)

Amount

Cast Iron Dual Plate (Wafer Type) Check Valve, Design standard API 594. Wafer Type Design, to take lesser space than the conventional Check Valve. Being light in weight, is more rigid than the standard Swing Type Check Valve, which needs expensive foundation and special supports. Being cylindrical body, stresses are uniformly distributed. Much longer seat life because of Bronze / S.S to Rubber contact. Less wear and tear of seat surfaces. End connections are designed to suit flanges drilled to ANSI B Class-125 / ASME B Class-150. Water hammering effect is minimized in this design, since the closing of valve does not depend upon any back pressure or flow. Each plate being half of the size of the swing check valve disc, provides straight flow path offering minimal resistance because of the spring’s assistance as closing of the valve initiates as soon as flow velocity dips below the designated minimum velocity. (NS) 150 MM Dia (NS)

Cast Iron Dual Plate (Wafer Type) Check Valve, Design standard API 594. Wafer Type Design, to take lesser space than the conventional Check Valve. Being light in weight, is more rigid than the standard Swing Type Check Valve, which needs expensive foundation and special supports. Being cylindrical body, stresses are uniformly distributed. Much longer seat life because of Bronze / S.S to Rubber contact. Less wear and tear of seat surfaces. End connections are designed to suit flanges drilled to ANSI B Class-125 / ASME B Class-150. Water hammering effect is minimized in this design, since the closing of valve does not depend upon any back pressure or flow. Each plate being half of the size of the swing check valve disc, provides straight flow path offering minimal resistance because of the spring’s assistance as closing of the valve initiates as soon as flow velocity dips below the designated minimum velocity. (NS)80MM Dia (NS)

Providing and Fixing 120 minutes fire rated heavy duty door closer of Size EN 3-5, with standard arm. desired finish conforming to 1S.3564/EN:1154 (NS)

Providing and Fixing 120 minutes fire rated SS 304 shaft mortise dead lock, 50-80 mm Back Set minimum 20 mm square forend with allen key inculidng SS304 dead strike plate conforming IS 16015:2022/EN 12209 (NS)

Providing and Fixing 120 minutes flush bolt (Dye-Cast Stainless Steel Finish of Length 300 mm for bottom (NS)

Providing and fixing factory made lSl marked un-insulated metal fire rated doorset assembly for all egress applications areas like utility rooms and service areas consisting of galvanized iron steel frame and double leaf shutter including necessary hardware accessories, conforming to FD 120 UD classification of lS 3614 .2021 with fire rating of 120 minutes integrity. The door frame and shutter shatl be made out of minimum 1.20 mm thick Gl Sheet with minimum 120 GSM Zinc coating as per lS: 277 . The entire flre rated doorset assembly shall be tested in unlatched condition as per lS 1 7518 (Part -1): 2022 Frame The frame shall be of minimum size 90 x 60 mm with grooved profile to take appropriate fire rated smoke seal, having mitred cut joints (self tab/screwed assembled at site) and provided with appropriate reinforcement suitable for taking hardware and flush fixing as per lS: 4351. The smoke seal material shall be of EPDM tested in accordancewith ASTM E-84 of minimum size 10x4 mm, fixed within the inbuilt groove or stuck with adhesive on the entire perimeter of the frame. The door frame shall lbe fixed in all three sides to masonry wall opening with CSl(Hex headed fasteners of minimum 8 mm dia size and minimuml 180 mm long with 8mm dia polyamide sleeves @ 5 numbers at each on vertical side and 3 numbers on top side. Door shutter: The double skin double leaf door shutter shall be consisting of minimum 46 mm thick and having box like structure, slots cut and holes punched for fixing of hardware with stiffener as per lS 16074 including Resin bonded honey comb paper core inflll material of density 5 kg/cum. Each door leaf shall be provided with vision panel, having maximum area of 0.12 sqm, of `120 minute fire rated minimum 6 mm thick clear borosilicate glass pane fixed with clip-on arrangement and fire rated ceramic tape having minimum size 13x2mm to be fixed all around the glass on both the sides. lntegral astragals to be provided for double leaf doors on the meeting style each on both active and inactive leaf. The door shutters shall be mounted on the frame with SS 304 grade ball bearing butt hinges as per EN 1935 .2OO2 or butt hinges as per lS 12817 both, of minimum size 100x75x3 mm @ 5 numbers hinges per door leaf upto 2400 mm height or as per test evidence, which ever is more, flxed with M6 25 screws. All doors shall be factory prepared for receiving appropriate hardware and provided with necessary reinforcernent for hardware accessories. Hardware Accessories: Fire doorset shall provided with one number fire rated SS 304 grade Mortise dead lock, 50-80 mm Back Set, mtnimum 20 mm Square forend with allen key Escutcheon of Stainless Steel, and 65r/0 mm cylinder with both side key conforming to lS: 16O15 :2O221EN 122O9, two pair of D type Pull handle of SS 304 grade of minimum 22 mm dia Centre to centre distance of 300 mm back to back fixing with spindle, one number 300 mm long Concealed lever action flush bolt (Dye-Cast Stainless Steel Finish) at boftom with SS dust proof socket and one number 600 mm long Concealed lever action flush bolt (Dye-Cast Stainless Steel Finish) on top of anactive leaf oF double door. Two number fire rated surface mounted heavy duty door closer of size EN 3-5 with standard arm, of desired finish conforming to lS 3564/EN `1 154 Finishing: Both frame and door shutters shall be factory finished with polyester powder coating of minimum 50 microns thick and shall have passed salt spray test as per lS:13871 of approved colour and shade all complete as per manufacturefs specifications and as per direction of the Engineer-in-charge. lnstallation: The hollow space in the door frame shall be filled / injected with fire rated self extinguishing type polyurethane foam (PUF) after installation at site of work. The rate shall be inclusive of complete fire rated door assembly, supply and installation by the approved manufacturer. Providing and fixing factory made lSl marked un-insulated metal fire rated doorset assembly for all egress applications areas like utility rooms and service areas consisting of galvanized iron steel frame and double leaf shutter including necessary hardware accessories, conforming to FD 120 UD classification of lS 3614 .2021 with 3614:202`l For non egress applacations like utility room and service area etc. (DSR-9.162D.1)

Providing and fixing factory made lSl marked un-insulated metal fire rated doorset assembly for all egress applications areas like utility rooms and service areas consisting of galvanized iron steel frame and double leaf shutter including necessary hardware accessories, conforming to FD 120 UD classification of lS 3614 .2021 with fire rating of 120 minutes integrity. The door frame and shutter shatl be made out of minimum 1.20 mm thick Gl Sheet with minimum 120 GSM Zinc coating as per lS: 277 . The entire flre rated doorset assembly shall be tested in unlatched condition as per lS 1 7518 (Part -1): 2022 FrameThe frame shall be of minimum size 90 x 60 mm with grooved profile to take appropriate fire rated smoke seal, having mitred cut joints (self tab/screwed assembled at site) and provided with appropriate reinforcement suitable for taking hardware and flush fixing as per lS: 4351. The smoke seal material shall be of EPDM tested in accordancewith ASTM E-84 of minimum size 10x4 mm, fixed within the inbuilt groove or stuck with adhesive on the entire perimeter of the frame. The door frame shall lbe fixed in all three sides to masonry wall opening with CSl(Hex headed fasteners of minimum 8 mm dia size and minimuml 180 mm long with 8mm dia polyamide sleeves @ 5 numbers at each on vertical side and 3 numbers on top side. Door shutter:The double skin double leaf door shutter shall be consisting of minimum 46 mm thick and having box like structure, slots cut and holes punched for fixing of hardware with stiffener as per lS 16074 including Resin bonded honey comb paper core inflll material of density 5 kg/cum. Each door leaf shall be provided with vision panel, having maximum area of 0.12 sqm, of `120 minute fire rated minimum 6 mm thick clear borosilicate glass pane fixed with clip-on arrangement and fire rated ceramic tape having minimum size 13x2mm to be fixed all around the glass on both the sides. lntegral astragals to be provided for double leaf doors on the meeting style each on both active and inactive leaf. The door shutters shall be mounted on the frame with SS 304 grade ball bearing butt hinges as per EN 1935 .2OO2 or butt hinges as per lS 12817 both, of minimum size 100x75x3 mm @ 5 numbers hinges per door leaf upto 2400 mm height or as per test evidence, which ever is more, flxed with M6 25 screws. All doors shall be factory prepared for receiving appropriate hardware and provided with necessary reinforcernent for hardware accessories. Hardware Accessories:Fire doorset shall provided with one number fire rated SS 304 grade Mortise dead lock, 50-80 mm Back Set, mtnimum 20 mm Square forend with allen key Escutcheon of Stainless Steel, and 65r/0 mm cylinder with both side key conforming to lS: 16O15 :2O221EN 122O9, two pair of D type Pull handle of SS 304 grade of minimum 22 mm dia Centre to centre distance of 300 mm back to back fixing with spindle, one number 300 mm long Concealed lever action flush bolt (Dye-Cast Stainless Steel Finish) at boftom with SS dust proof socket and one number 600 mm long Concealed lever action flush bolt (Dye-Cast Stainless Steel Finish) on top of anactive leaf oF double door. Two number fire rated surface mounted heavy duty door closer of size EN 3-5 with standard arm, of desired finish conforming to lS 3564/EN `1 154 Finishing:Both frame and door shutters shall be factory finished with polyester powder coating of minimum 50 microns thick and shall have passed salt spray test as per lS:13871 of approved colour and shade all complete as per manufacturefs specifications and as per direction of the Engineer-in-charge. lnstallation: The hollow space in the door frame shall be filled / injected with fire rated self extinguishing type polyurethane foam (PUF) after installation at site of work. The rate shall be inclusive of complete fire rated door assembly, supply and installation by the approved manufacturer. Providing and fixing factory made lSl marked un-insulated metal fire rated doorset assembly for all egress applications areas like utility rooms and service areas consisting of galvanized iron steel frame and double leaf shutter including necessary hardware accessories, conforming to FD 120 UD classification of lS 3614 .2021 with only as per lS 3614:2021- For egress application like utility room and service area etc.(DSR-9.162C.1)

Providing and fixing factory made lSl marked un-insulated metal fire rated doorset assembly for all egress applications areas like utility rooms and service areas consisting of galvanized iron steel frame and double leaf shutter including necessary hardware accessories, conforming to FD 120 UD classification of lS 3614 .2021 with fire rating of 120 minutes integrity. The door frame and shutter shatl be made out of minimum 1.20 mm thick Gl Sheet with minimum 120 GSM Zinc coating as per lS: 277 . The entire flre rated doorset assembly shall be tested in unlatched condition as per lS 1 7518 (Part -1): 2022 FrameThe frame shall be of minimum size 90 x 60 mm with grooved profile to take appropriate fire rated smoke seal, having mitred cut joints (self tab/screwed assembled at site) and provided with appropriate reinforcement suitable for taking hardware and flush fixing as per lS: 4351. The smoke seal material shall be of EPDM tested in accordancewith ASTM E-84 of minimum size 10x4 mm, fixed within the inbuilt groove or stuck with adhesive on the entire perimeter of the frame. The door frame shall lbe fixed in all three sides to masonry wall opening with CSl(Hex headed fasteners of minimum 8 mm dia size and minimuml 180 mm long with 8mm dia polyamide sleeves @ 5 numbers at each on vertical side and 3 numbers on top side. Door shutteThe double skin double leaf door shutter shall be consisting of minimum 46 mm thick and having box like structure, slots cut and holes punched for fixing of hardware with stiffener as per lS 16074 including Resin bonded honey comb paper core inflll material of density 5 kg/cum. Each door leaf shall be provided with vision panel, having maximum area of 0.12 sqm, of `120 minute fire rated minimum 6 mm thick clear borosilicate glass pane fixed with clip-on arrangement and fire rated ceramic tape having minimum size 13x2mm to be fixed all around the glass on both the sides. lntegral astragals to be provided for double leaf doors on the meeting style each on both active and inactive leaf. The door shutters shall be mounted on the frame with SS 304 grade ball bearing butt hinges as per EN 1935 .2OO2 or butt hinges as per lS 12817 both, of minimum size 100x75x3 mm @ 5 numbers hinges per door leaf upto 2400 mm height or as per test evidence, which ever is more, flxed with M6 25 screws. All doors shall be factory prepared for receiving appropriate hardware and provided with necessary reinforcernent for hardware accessories. Hardware Accessories:Fire doorset shall provided with one number fire rated SS 304 grade Mortise dead lock, 50-80 mm Back Set, mtnimum 20 mm Square forend with allen key Escutcheon of Stainless Steel, and 65r/0 mm cylinder with both side key conforming to lS: 16O15 :2O221EN 122O9, two pair of D type Pull handle of SS 304 grade of minimum 22 mm dia Centre to centre distance of 300 mm back to back fixing with spindle, one number 300 mm long Concealed lever action flush bolt (Dye-Cast Stainless Steel Finish) at boftom with SS dust proof socket and one number 600 mm long Concealed lever action flush bolt (Dye-Cast Stainless Steel Finish) on top of anactive leaf oF double door. Two number fire rated surface mounted heavy duty door closer of size EN 3-5 with standard arm, of desired finish conforming to lS 3564/EN `1 154 Finishing:Both frame and door shutters shall be factory finished with polyester powder coating of minimum 50 microns thick and shall have passed salt spray test as per lS:13871 of approved colour and shade all complete as per manufacturefs specifications and as per direction of the Engineer-in-charge. lnstallation: The hollow space in the door frame shall be filled / injected with fire rated self extinguishing type polyurethane foam (PUF) after installation at site of work. The rate shall be inclusive of complete fire rated door assembly, supply and installation by the approved manufacturer. Providing and fixing factory made lSl marked un-insulated metal fire rated doorset assembly for all egress applications areas like utility rooms and service areas consisting of galvanized iron steel frame and double leaf shutter including necessary hardware accessories, conforming to FD 120 UD classification of lS 3614 .2021 with fire rating of 120 minutes integrity. The door frame and shutter shatl be made out of minimum 1.20 mm thick Gl Sheet with minimum 120 GSM Zinc coating as per lS: 277 . The entire flre rated doorset assembly shall be tested in unlatched condition as per lS 1 7518 (Part -1): 2022 Single leaf un-insulated metal fire rated door and frame of FD 120 UD with 120 minutes integrity only as per lS 3614:2021 - For non egress application like area shafts etc. (DSR-9.162B.1)

Providing and fixing factory made lSl marked un-insulated metal fire rated doorset assembly for all egress applications areas like utility rooms and service areas consisting of galvanized iron steel frame and double leaf shutter including necessary hardware accessories, conforming to FD 120 UD classification of lS 3614 .2021 with fire rating of 120 minutes integrity. The door frame and shutter shatl be made out of minimum 1.20 mm thick Gl Sheet with minimum 120 GSM Zinc coating as per lS: 277 . The entire flre rated doorset assembly shall be tested in unlatched condition as per lS 1 7518 (Part -1): 2022 Double leaf un-insulated metal fire rated doorset of FD 120 UD classification with 120 minutes integrity only as per lS 3614:2021- For egress application like utility room and service area etc. (DOOR SIZE FD 120MIN SIZE= 2.0X2.1= 4.2 MTR.,FOR 53X4.25=222.6 SQMTR.) (DSR-9.162C.1)

Providing and fixing factory made lSl marked un-insulated metal fire rated doorset assembly for all egress applications areas like utility rooms and service areas consisting of galvanized iron steel frame and double leaf shutter including necessary hardware accessories, conforming to FD 120 UD classification of lS 3614 .2021 with fire rating of 120 minutes integrity. The door frame and shutter shatl be made out of minimum 1.20 mm thick Gl Sheet with minimum 120 GSM Zinc coating as per lS: 277 . The entire flre rated doorset assembly shall be tested in unlatched condition as per lS 1 7518 (Part -1): 2022 Frame The frame shall be of minimum size 90 x 60 mm with grooved profile to take appropriate fire rated smoke seal, having mitred cut joints (self tab/screwed assembled at site) and provided with appropriate reinforcement suitable for taking hardware and flush fixing as per lS: 4351. The smoke seal material shall be of EPDM tested in accordancewith ASTM E-84 of minimum size 10x4 mm, fixed within the inbuilt groove or stuck with adhesive on the entire perimeter of the frame. The door frame shall lbe fixed in all three sides to masonry wall opening with CSl(Hex headed fasteners of minimum 8 mm dia size and minimuml 180 mm long with 8mm dia polyamide sleeves @ 5 numbers at each on vertical side and 3 numbers on top side. Double leaf un-insulated metal fire rated doorset of FD 120 UD classification with 120 minutes integrity only as per lS 3614:2021- For egress application like utility room and service area etc. (DOOR SIZE Electric Shaft FD 120MIN SIZE= 1X2.1= 2.1 MTR.,FOR 7X2.1=14.7 SQMTR.) (9.162C.1)

Providing and fixing of pressure switch in M.S. pipe line including connection etc. as required.(DSR -18.22) New

Providing, fixing, testing and commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories. (DSR-18.21.1) Pendent Sprinkler

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required 100 MM dia (DSR-18.14.5)

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.(DSR -18.15.3) 150mm dia

Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (DSR-18.7) 100mm dia DSR 18.7.7)

Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (DSR-18.7) 25mm dia (DSR 18.7.1)

Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (DSR-18.7) 32mm dia (DSR 18.7.2)

Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (DSR-18.7) 40mm dia (DSR 18.7.3)

Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (DSR-18.7)80mm dia (DSR 18.7.6)

Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required 65MM dia (DSR-18.7.5)

Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame andpainting with two or more coats of synthetic enamel paint of required shade complete as required 150-MM dia

Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame andpainting with two or more coats of synthetic enamel paint of required shade complete as required 200 MM dia (DSR-18.7.9)

SITC of Brass / Bronze Lever Operated Ball Valve Full Flow with Stainless Steel Ball (AISI 304 and Spindle AISI 410) with Setting and DGland of Super Quality Having Minimum Working Pressure of 20kg/CM :(NS) 25 mm dia (NS)

Supply and Fixing H type Pull handle SS 304 of minimum 22 mm dia. Centre to centre distance of 300mm back to back fixing with spindle (NS)

Supply and fixing of SS Ball Bearing Hignes of size 100 x 75 x 3 mm complete with SS Screws of BB 1953 Becker Fire solution Make ( 4 Nos.per panel ) ( Requried For All Doors) as per the directions of Engineer-in-charges (NS)

Supply of burden type Stainless Steel dial type pressure gauge with brass isolation valve and pipe. (For each Pump room ). (NS)

Supply of Fire Bucket Stand having four 9 ltr. Sand filled buckets 4 stand 1 set. (NS)

Supply OF ABC type fire extinguisher ISI mark IS code 15683 –2006 capacity: 06 kgs 90 % MAP(Mono Amonium phosphate) pressurized with dry nitrogen . (NS)

Supply OF Co2 type fire extinguisher ISI mark IS code 15683 – 2006 capacity: 4.5 kg with 1 mtr long hosepipe. (NS)

Supply of fire brigade Draw out connection confirming to IS : 4038-1986 with 150 mm Non return valve/ strainer incluiding necessary fittings the word FIRE BRIGADE DRAW OFF to be painted on the box complete all as specified and directed . (NS)

Supply Of Internal Fire Hose Box , Wall Mounting Or Free Standing Type , Made Out Of Fibre Glass Reinforced Plastic Of Approved Colour Of Weather proof hose cabinet of size 750 x 600 x 250mm, to accommoate Two 15 m Length Of Delivery Hoses And A Branch Pipes With Glass Fronted Double Door With Lock And Keys And Break Glass Recess For Keys ,Complete In All Manners.(NS)

Supplying and fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required.(DSR -18.18.2) Stainless Steel (Grade 304)

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : (DSR - 18.16.2) Stainless Steel (Grade 304)

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required. (DSR-18.20)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve and nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve and M.S. Pipe and socket. (DSR -18.17.1) 30 MM

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : (DSR - 18.19.1) 2 way-100 mm dia M.S. Pipe

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : (DSR - 18.19.2) 4 way - 150 mm dia M.S. Pipe

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : (DSR - 18.9.2) Single headed Stainless steel

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required. 100MM dia (DSR -18.11.5)

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required. 150MM dia (DSR -18.11.6)

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required. 80 MM dia (DSR -18.11.4)

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required.200MM dia (DSR -18.11.7)

Supplying, installation, testing and commissioning of (Diesel Driven Pump) suitable for automatic operation and consisting of following, complete in all respects, as required : Horizontal type, multistage, centrifugal pump of cast ofiron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. Description of Item DSR Code No. Description of Item Unit Rate Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, Binstruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. Diesel Driven Pump 2850LPM, 70 Mtr Head (DSR - 18.2.2)

Supplying, installation, testing and commissioning of .Main Fire Pump for HYDRANT PUMP Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required (a)Horizontal type, multistage, centrifugal, split casing pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-`F` insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads. . Main Fire Pump for HYDRANT PUMP Discharge:2850LPM, 70 Mtr Head (DSR - 18.1.2)

Supplying, installation, testing and commissioning of .Main Fire Pump for Sprinkler Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required (a)Horizontal type, multistage, centrifugal, split casing pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-`F` insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads. . Main Fire Pump for Sprinkler Pump Discharge:2850LPM, 70 Mtr Head (DSR - 18.1.2)

Supplying, installation, testing and commissioning of Electric Driven Pressurisation Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-`F` insulation, conforming to IS : 325.M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads Jockey Pump 180LPM, HEAD -70 Mtr (DSR - 18.3.2)

Tank Refilling fire Brigade Connection 150mm dia 4 way (NS)

Bidder Name

Amount

M/s Royale Meridian India Pvt Ltd (GSTN-NA) BID ID -1360517

M/s Daksha Construction (GSTN-06ATMPK0334NIZI) BID ID -1359107

M/s Daksha Construction (BID ID -1359107)

M/s Daksha Construction (BID ID -1359107)