PROVISION OF TILING RAIN SHED LANDSCAPING SPECIAL REPAIR TOILET IN DSC LIVING ACCN AND CERTAIN EM WORKS INCLUDING PROVN OF FOUNTAIN AND OTHER CONNECTED WORKS AT AF STN MAHARAJPUR

Amount

Surface dressing n exc 15 cm deep and getting out in soft/ loose soil and removing surplus soil to a distance n.exc. 50m and making good surface complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/ loose soil comlete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete n.exc 15 cm thick below or above ground level including removal demolished material exc.250m and depositing where directed upto total distance of 1.5Km complete all as directed.

Excavating in trenches n'exc 1.5 m width and n'exc 1.5 m in depth for foundation etc n'exc 10 sqm on plan and n'exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Excavating over areas, n exc 1.5m deep and getting out in soft/ loose soil complete all as specified and directed.

Excavating in post holes (or similar holes) in soft/ loose soil, each n.exc 0.5 cum, getting out and removing surplus soil to a distance n.exc 50 m and making good surface complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

Taking down chowkhats or frames with shutters ( without taking off shutters from the frames) of area not exc 1.50 Sqm each complete all as specified and directed.

S&F solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube fixed with 75mm long MS screws with PVC fasteners to wall all including repair of james of wall & finishes complete all as specified and directed .

S&F factory made solid PVC moulded door shutter, 30mm thick (Stiles),consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stilesand plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain color PVC sheet to be fitted in the MS welded/sealed to the stiles & rails with suitable P VC sheet beading and joined together with solvent cement complete all as specified and directed.

S&F in repair 3.00 mm thick sheet glass ordinary quality type & glazing with oil putty in squares not exc 0.5 Sqm in each pane, including hacking out old broken glass pane of any thickness and size complete all as specified and directed.

S&F in repair galvanized mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanized wire staples etc. in wooden door / window, completed all as specified and directed.

Taking down of cement plaster in any description on brick or stone wall etc., incl hacking out joints for key scrubbing down with water etc. all as specified and directed.

M & L for 5mm thick rendering in Cement Mortar 1:3 on concrete surfaces as on ceiling finished even and smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick on fair faces of brick work or on concrete surfaces in Cement Mortar 1:4 surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or on concrete surfaces in Cement Mortar 1:4 mixed with water proofing compound as per manufacturers instructions surface finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately under respective item of BOQ.

M & L preparation of newly plastered surfaces of wall and applying three coats of white wash, complete all as specified and directed.

M & L preparation of newly plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.

M&L for premium quality non skid, joint free coloured ceramic floor tiles 7- 8 mm thick (square/rectangular) area of each tiles exc 0.06 sqm but not exc 0.11 sqm, in floors etc set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including 15mm thick screed bed in Cement Mortar (1:4) complete all as specified and directed.

M&L for premium quality glazed ceramic tiles of size 450 x 300 x 7-8 mm thick coloured on vertical surfaces such as skirting/dados etc, set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including rendering 10 mm thick in Cement Mortar 1:3 on wall complete all as specified and directed.

M&L for ceramic digital stone kraft/ stone finish (gloss/matt finish) tiles of maximum size 450x300 x 6-7mm thick coloured on vertical surfaces such as skirting/dados etc, set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including 10 mm thick rendering in Cement Mortar 1:3 on wall complete all as specified .

M&L 25mm thick PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in levelling course finished even and fair for laying floor etc all as specified and directed

Supply only integral water proofing compound complete all as specified and directed.

M&L for formwork to faces of walls, retaining walls, abutments, parapets and staircase railing and similar works including attached pillasters, buttresses etc, vertical or batter for rough finish surfaces of concrete flat complete all as specified and directed.

M&L for mild steel TMT bars as in reinforcement, 10mm dia and over cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete and all as specified and directed.

M&L machine made prepolished chequered cement concrete tiles 20cm x 20cm x 25mm thick, set and jointed and pointed in neat cement slurry with grey cement and pigment in floors over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

M&L for RCC 1:1.5:3 Mix, Type A1 (Using 20 mm graded stone aggregate) as in walls, retaining walls, basement walls/ rafts, ballast walls and the like of any thickness, above top of footing including attached pilaster and buttresses complete all as specified and directed.

M&L for 50 mm thick cement concrete 1:2:4 Mix, type B1 (Using 20 mm graded stone aggregate) mixed with water proofing compound as per manufacturers instructions finished even and smooth as in floor complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately under respective item of BOQ.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling of asbestos cement ( corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

M&L for brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6m mean radius built in Cement Mortar 1:6, complete all as specified and directed.

Description all as per srl item no. 34.00 here-in-before but in Cement Mortar 1:4.

S&F rolled section for structural steel work as in main and cross beams, hip and jack rafters, purlin where connected to common rafters and running rails and guides for sliding crane, fixed with angle cleats or other connecting plates/ bolts, conforming to Fe-290(Gde-E-165) complete all as specified and as directed. Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete.

S&F mild steel rolled section for structural steel work as in vertical post, main and cross beams, hip and jack rafters, purlin where connected to common rafters and running rails and guides for sliding crane, fixed with angle cleats or other connecting plates/ bolts, conforming to Fe-410-W (Gde-E-250) quality-A complete all as specified and as directed. [Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete.]

S&F Pre-painted galvalume aluminium zinc coating GI based semi corrugated steel sheet 0.50 mm thick of an approved colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for cutting holes into through brick walls built in cement mortar and making good in cement mortar (1:3) or PCC (1:2:4) type B1 to match with existing surface superficial area exc 400sqcm but not exc 0.10 sqm complete all as specified and as directed.

M&L for cutting chases in brick wall, pinning in and making good in cement mortar (1:4) to match with existing surface for cutting not exc 10cm girth complete all as specified and as directed.

M&L for 8 mm overall thickness hollow polycarbonate sheet of approved make of wall thickness 0.8 mm to 1 mm and fixed to roof roofs and the like with screws as per manufacturers instructions complete all as specified and directed.

M&L for 75 mm thick PCC 1:2:4 type B2 (using 40mm graded stone aggregate) as in floor etc finished fair and even complete all as specified and directed

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or grith complete all as specified and directed.

Removing excavated material exc 500m but n.exc 1.50 KM and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

Removing excavated material n.exc 50 M and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed.

M & L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment laid in floor and joints of interlocking tiles/ paver block to be filled with fine sand and brooming etc complete all as specified and directed.

M & L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 grade with grey cement and pigment laid in floor and joints of interlocking tiles/ paver block to be filled with fine sand and brooming etc complete all as specified and directed.

M & L for 50mm thick Sand filling / stone dust under floors or in foundations including watering and consolidation etc complete all as specified and directed.

M&L for PCC 1:2:4 type B1 ( using 20 mm graded stone aggregate) as in roof kerbs or mud stops, rounded on edge and similar nature of work complete all as specified and as directed.

M&L for preparing newly plastered surfaces of wall and applying two coats of cement base paint over a coat of cement primer complete all as specified and directed.

M&L for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like bedded over and including 15mm thick screed bed in CM (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S&F false ceiling 4mm thick HPSC pre-prime non asbestos fiber cement building board (E-classic ) decorative finish fixed to aluminum or powder coated galvanised snap grid frame work with hold down clips in ceiling grid system 600 x 600 mm with main runner 32 x 24 x 0.8 mm , cross tee 26 x 24 x 0.80mm and wall angle 22.2 x 22.2 x 0.65 mm in ceiling suspended @ 1.2m c/c both way with 1.6 mm dia GI wire hangar fixed with steel dash fasteners or from purlin of roof with butterfly clips hold down etc, complete ,( main runner / cross tee /wall angle of MS galvanised powder coated ), as per manufacturere instruction complete all as specified and directed. Make:- Everest/Ramco/Charminar Note : Cost of making frame work and board (cut out) for fixing light fitting grill diffuser etc shall be deemed included in the quoted rate.

Demolition of brickwork or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for including cutting of reinforcement complete all as specified and as directed.

Demolition of PCC of any description and in any position not otherwise described, including removing demolished material to a distance exc 500M but n exc 1.50 KM distance and depositing where as directed, complete all as directed.

M&F for applying evenly a tack coat of industrial bitumen 85/25 @ 1.20 kg/ Sqm including cleaning the surface complete all as specified.

M&L, for cement concrete 1:7:12 using 40mm graded brick agregate as in filling under sunken floors and foundations. complete all as specified.

M&L for 15 mm thick plaster in CM 1:6 on brick work or concrete surface on wall, finished even & smooth without using extra cement complete all as specified and directed.

S&F 1 mm thick steel rolling shutters, push pull or manual type, without ball bearing , as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated complete all as specified and directed.

S&F including fabricating of aluminium powder coated having minimum thickness of powder coating 50 micron for door / window/ ventilator frame with one or more rebates or aluminium section of two or more tracks in case sliding window including necessary joining cleats, glazing clips for fixing of screw in wall or floor etc., aluminium sections as approved by GE complete all as specified and directed. Note : - (i) Builders Hardware shall measured and paid separately under respective item of Schedule 'A' . (ii) Only weight of aluminium section shall be measured and paid. No claim what so ever shall be entertained by the Govt on this account. (iii) Thickness of section shall not be more than 2mm.

S&F for aluminium grills of size exc 5mm x 7.5mm and aperture n. exc 80mm incl fixing with aluminium hannel 1mm thick with steel screw and tint match with existing complete all as specified.

S&F 5.5 mm thick sheet glass ordinary quality in square n exc 0.5 Sqm in each pane with oil putty/wooden beading any thickness and size complete all as specified and directed

S&F including fabricating of aluminium powder coated having minimum thickness of powder coating 50 micron for door / window/ ventilator shutter including necessary joining cleats, glazing clips, aluminium snap beading having minimum wt 100gm/RM, rubber neoprene gasket, screws, dash fasteners, rawel plug for fixing of screw in wall or floor etc., including star locks, roller in case sliding winow shutter, aluminium sections as approved by GE complete all as specified and directed. Note : - (i) Builders Hardware shall measured and paid separately under respective item of Schedule 'A' . (ii) Only weight of aluminium section shall be measured and paid. No claim what so ever shall be entertained by the Govt on this account. (iii) Thickness of section shall not be more than 2mm.

S&F 100 mm long butt hinges extruded aluminium alloy with galvanised MS hinge pin, anodised complete all as specified and as directed.

S&F for 150 mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F anodised aluminium sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of size 250mm complete all as specified and directed.

S&F for 150 mm long anodised, aluminium handles, cast type complete all as specified and as directed.

S&F in repairs WC squatting pan “Orissa Pattern” of size 580 x 440mm white with integral foot rest (excluding flushing cistern & flush pipe) including replecement of cast iron 100mm P/S trap and connection to trap and flush pipes etc and lime concrete bedding complete all specified.

S&F in repairs 10 ltr capacity PVC valveless, syphonic action type flushing cistern low level white with inlet, ball valve, float and handle including connection to pipe complete all as specified and directed.

S&F in repair counter top vitreous china wash hand basin, white, flat back, size 520mm x 450mm excluding taps, chain and plug and porcelain stopper but including cutting for and pinning in ends of and including brackets, waste pipe & PTMT waste coupling of 32mm dia and fancy type 15 mm bore brass Pillar Tap complete all as specified and directed. Note : Rate quoted under this item deemed included fixing of taps, plug and chain and connecting up to supply pipes, wastes or traps etc.

S&F in repair vitreous china urinal flat back size of 390 x 375 x 590 mm, white with grating, union for discharge pipe on bracket excluding flushing cistern flush pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plug with and including 60mm long brass screws complete and all as specified and directed. Make:- Cat part no. 5004 of Cera or other equivalent as approved.

Taking up or down 15mm bore steel tubing and connections, including seggregation serviceable pipes cleaning for re-fixing or removal unserviceable pipes from site complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections, including seggregation serviceable pipes cleaning for re-fixing or removal unserviceable pipes from site complete all as specified and directed.

Re-fixing of old steel GI tubing, 15mm bore and connections in new or old position (walls, ceiling, floors etc) with and including all new fittings complete all as directed. [NOTE:- Serviceable pipe shall be obtained from srl item no. 74.00 here-in-before for reuse.]

Re-fixing of old steel GI tubing, 20mm bore and connections in new or old position (walls, ceiling, floors etc) with and including all new fittings complete all as directed. [NOTE:- Serviceable pipe shall be obtained from srl item no.75.00 here-in-before for reuse.]

S&F GI tubing 15mm dia bore medium grade with and including all fittings ISI marked and fixed to wall, floor and ceiling etc complete all as specified and as directed.

S&F GI tubing 20mm dia bore medium grade with and including all fittings ISI marked and fixed to wall, floor and ceiling etc complete all as specified and as directed.

S & F in repair fancy type angle stop cock, 15 mm dia, cast copper alloy, with chromium plated, screwed down , high pressure, with capstan head, screwed both ends for iron pipe or for unions and fixed, complete all as specified and as directed.

S & F in repair Bib taps, 15 mm dia, cast copper alloy, fancy type with capstan heads ,chromium plated, screwed down , screwed for iron pipe or for brass ferrule and fixed, complete all as specified and as directed.

S&F in repairs PVC connections 15mm size of PTMT of 450mm long. complete all as specified and directed.

S & F 15 mm bore pillar taps, cast copper alloy, with capstan heads, chromium plated, Fancy type screwed down for pipe, high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe complete all as specified and directed.

S&F in repair 32mm dia PVC waste pipe complete all as specified and directed.

S&F aluminium tubular towel rail, 20mm dia, D type, 60 cm long between flanges, fixed with rawl plugs complete all as specified and directed.

S&F cast iron floor trap with grating including jointing to waste pipe of 75mm size complete all as specified & directed.

S&F in repairs 15mm bore fancy type overhead shower with arm swivel joint chromium plated screwed down Complete all as specified. ( Make- Hindware/ Jaquar /ESSCO)

Dismantling existing water storage tank of capacity exc 250 Litre but not exc 500 litres, removing from site of work complete all as specified and as directed.

Dismantling existing water storage tank of capacity exc 500 Litre but not exc 1000 litres, removing from site of work complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank of capacity 1000 Litre, double layer construction, ISI mark (cylindrical vertical with closed top) hoisted and fixed in position with and including 20 mm dia GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings, of following capacity of tank complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank of capacity 500 Litre, double layer construction, ISI mark (cylindrical vertical with closed top) hoisted and fixed in position with and including 20 mm dia GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings, of following capacity of tank complete all as specified and as directed.

S&F ball/float valve 20 mm bore (Minimum weight 210 grams) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipes or brass ferrule and fixed of following size complete all as specified and as directed.

S&F in repair gunmetal globe or gate valves, 20 mm bore, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&Ffor 110 mm bore PVC (SWR) pipes ISI marked single socketed, in any length with rubber ring joints and jointed with adhesive and laid in floors/ trenches complete all as specified.

S&Ffor 110 mm bore PVC (SWR) pipes ISI marked single socketed, in any length with rubber ring joints and jointed with adhesive and fixed to wall complete all as specified.

S&F for100 mm bore PVC (SWR) bend ISI marked and fixed in position with adhesive complete all as speciefied.

S&F for 110 mm bore PVC (SWR) branch piece ISI marked double and fixed with adhesive complete all as speciefied.

S&F for 110 mm bore PVC (SWR) single T ISI marked and fixed with adhesive complete all as speciefied.

S&F for PVC (SWR) 110 mm bore vent cowl complete all as speciefied.

S&F energy saving, enviromrntal friendly, long life, exclusively innovative, die cast aluminium IP65 flood light luminair with high power LED as light source 80 W LED 6000K with and including 1.5 Sqmm 3 Core copper conductor cable in replacement with existing HPSV/ MH light fittings of any description complete all as specified and directed. Make: Bajaj Cat Part No. BJFL 80 W LED or equivalent in Crompton Greaves/ Wipro/Philips

S&F energy saving, enviromrntal friendly, long life, exclusively innovative, die cast aluminium IP65 flood light luminair with high power LED as light source 60 W LED 4000K with and including 1.5 Sqmm 3 Core copper conductor cable in replacement with existing HPSV/ MH light fittings of any description complete all as specified and directed. Make: Bajaj Cat Part No. BJFL 60 W LED or equivalent in Crompton Greaves/ Wipro/Philips

Design, Supply, install, testing and commissioning of fountain consisting of following :- (a) Fountain ring dia 12 ft, dia of spray height 6 ft to 8 ft maximum with and inclusive 50 mm GI medium grade with GI base stand assembly with minimum 02 outlet with vertical adjustable jets- 60 numbers made of brass with chromium plated of size 3/8 inch with base control and plumbing assembly. Make: Uday fountain/ TY fountain/ Poineer fountain. (b) Submersible pump set 5HP, 3 Phase, 50 Hz, 415 volt, 2800 rpm, suction 80 mm and discharge 65 mm, discharge 1327 LPM at 8 mtr head high discharge for fountain purpose- 01 number. Make: Lubi/ Kirlosker or as approved by GE. (c) Under water LED lights having IP 68 protection, 12 V DC, 9 Watt having color red, green, blue and white with base stainless steel standard height 100mm and angle adjustable all confirming to ISO2015: 9001.- 12 sets. Make Uday or as approved by GE. (d) Programmable controller with 6 stage dancing controller of drivers/transformers for LED lights 12 V DC supply voltage with encloses and indicators. Make: Havells/ CG/ Uday or asapproved by GE. (e ) Double door control panel box powder coated including DOL starter suitable for 5 HP submersible pump set as approved by GE. (f) MCB, Electric control Voltmeter and Ammeter of Make: L&T/ Havells as approved by GE. (g)Copper flexible cable 2.5 sqmm 3 core and 1.00 sqmm 4 core- 10 mtr length. Make: polycab. (h) Fountain on line strainer with screen filter of size 65 mm dia as per approved make. (J) Providing all other miscellaneous items like anchor bolt, nut bolt, screw, clamp, welding work and minor civil work as required to complete the job. Note:- The fountain shall be installed & commissioned by original fountain manufacturer or by his authorized representative.

M/s Manish Contractor

M/s Pal Construction