RFQ 10638 Renovation and Face lifting of Mahila Samaj Building at KCC Township

Dismantling of steel structure such as platforms, support railing, hoppers, chutes, ducts, cells dismantling of mech. Equipments and elect. Equipments/ assemblies including rubber lined pipe line all heights

Providing & Fixing Precoated galvanized iron profile /Trapezoidal profile sheets (Size, Shape and pitch of corrugation as approved by Engineer-In-Charge) manufactured out of 0.50 mm (0.05%)TCT with zinc coating 120 grams per sqm as per IS:277, in 240 mpa steel grade, 5-7 microns epoxy primer on both sides of the sheet and polyester top coating 15-18 micron. Sheets should have protective guard film of 25 microns minimum to avoid scratches during transportation. The sheet shall be fixed using self drilling/self tapping screws size(5.50-8 x55 mm) with EPDM seal, complete up to any pitch in Horizontal/Vertical or curved surfaces, excluding the cost of purlins, rafters & trusses and including cutting to size and shape whenever required.

Providing and fixing precoated galvanised steel sheets roofing accessories 0.50 mm(+0.50%) total coated thickness , Zinc coating 120 grams per sqm as per IS 277, 240 mpa steel grade , 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws of size ( 5.5-8 x 55 mm with EPDM seal) complete.(A) Ridges plain(500-600 mm).

Providing and fixing precoated galvanised steel sheets roofing accessories 0.50 mm(+0.50%) total coated thickness , Zinc coating 120 grams per sqm as per IS 277, 240 mpa steel grade , 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws of size ( 5.5-8 x 55 mm with EPDM seal) complete.(A) Flashings/Aprons (Up to 600 mm).

Providing and fixing precoated galvanised steel sheets roofing accessories 0.50 mm(+0.50%) total coated thickness , Zinc coating 120 grams per sqm as per IS 277, 240 mpa steel grade , 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws of size ( 5.5-8 x 55 mm with EPDM seal) complete.(A) North Light Curves

Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters lead of: Asbestos sheet

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colors and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 60x60 cm

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

20 mm cement plaster of mix :1:4 (1 cement: 4 fine sand)

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead.

40 mm thick marble chips flooring, rubbed and polished to granolithic finish, under layer 28mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size) and top layer 12mm thick with

Half brick masonry with F.P.S. bricks of class designation 75 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) at plinth level with :Cement mortar 1:6 (1 cement : 6 coarse sand)

RANDOM RUBBLE MASONRY WITH HARD STONE IN SUPERSTRUCTURE INCLUDING LEVELLING UP WITH CEMENT CONCRETE 1:6:12 ( 1 CEMENT : 6 COARSE SAND :12 GRADED STONE AGGREGATE 20 MM NOMINAL SIZE ) WITH CEMENT MORTAR 1:6 (1 CEMENT : 6 COARS SAND)

Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: In cement mortar

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge. In cement mortar

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 meters lead as per direction of Engineer - in - charge.1:3:6 or richer mix

Carriage of material by mechanical transport including loading, unloading and stacking: Lime, moorum, building rubbish: Lead 1 KM.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m All kinds of soil.

STONE SOLING UNDER FLOOR INCLUDING FILLING VOIDS WITH STONE CHIPS AND SAND, RAMMING, WATERING AND CONSOLIDATING ETC. COMPLETE

Providing and fixing in position inter locking pre cast cement concrete Blocks of M-15 Concrete Grade and minimum thickness 60 mm Including required ballu mitty below and in joints.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.40mm thick with 20mm nominal

P/F stainless steel Kitchen Sink with C.I. Brackets and S S Plug 40 MM , including Painting of fittings and brackets, cutting and making good the walls whenever required. ( A) Kitchen Sink with Drain Board :510X1040 MM bowl depth 250 MM

DISMANTLING WOODEN PARTITION WALL INCLUDING FRAME WORK, COMMERCIAL PLY, DOOR SHUTTER WITH BUTT HINGES, WOODEN BEADING ETC. COMPLETE, AS PER DIRECTION OF ENGINEER IN- CHARGE. LABOUR RATE ONLY

Providing and fixing at all height false ceiling including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia. bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting with : Fully perforated Gypsum Plaster Board of size 1200 X 2400 X12.5 mm having approx 15% perforated area with perforation size and pattern as approved by the EIC and as per manufacturer’s specification, with all 4 size tapered and back by acoustical tissue with NRC value not less than 0.60

Providing and fixing aluminium work for doors, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved mark confirming to IS : 733 and IS : 1285 , fixed with dash fasteners of required dia. and size , including necessary fillings up of gaps at junctions at top, bottom and sides with required EPDM Rubber / Neoprene gasket etc. Aluminium sections shall be smooth rust free straight metered and jointed mechanically wherever required including clit angle aluminium snap beading for glazing / panneling C.P Brass/ stainless steel screws all complete as per architectural drawing and the directions of Engineering In Charge (Glazing ,paneling dash fasteners to be paid for separately). For shutters of doors , windows and ventilators including providing and fixing hinge/pivots and making provision for fixing of fittings wherever required including the cost of EPDM Rubber / Neoprene gasket required (fitting shall be paid for separately) Power coated aluminium (Minimum thickness of powder coating 50 micron).

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminum snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in paneling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked for doors including cost of cutting floors as required embedding in floors and cover plate with brass pivot and single piece M.S. Sheet outer box with slide plate etc With Brass cover plate

PROVIDING AND FIXING BRIGHT FINISHED BRASS 100 MM. MORTICE LATCH AND LOCK WITH 6 LEVERS AND A PAIR OF LEVER HANDLES WITH NECESSARY SCREWS ETC. COMPLETE.(BEST MAKE OF APPROVED QUALITY)

Structural steel work riveted bolted or welded in built up section, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

REINFORCED CEMENT CONCRETE WORK IN BEAMS, SUSPENDED FLOORS, ROOFS HAVING SLOPE UPTO 15 DEGREE, LANDINGS , BALCONIES, SHELVES, CHAJJAS, LINTELS, BANDS, PLAIN WINDOW SILLS, STAIRCASES AND SPIRAL STAIR CASES UPTO TO FLOOR FIVE LEVEL EXCLUDING

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Cold twisted bars

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade :One or more coats on old work.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :Old work (one or more coats)

REMOVING DRY OR OIL BOUND DISTEMPER BY SCRAPPING, SAND PAPERING AND PREPARING THE SURFACE SMOOTH INCLUDING NECESSARY REPAIRS TO SCRATDHES ETC. COMPLETE.

Finishing walls with ISI Approved weather proof ACE exterior Emulsion including exterior wall primer on wall surfaces to give even and smooth finishing.(A) New work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

Applying priming coat :With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

PROVIDING AND FIXING M.S.WIRE GAUGE TO WINDOWS,CLEARSTORET WINDOWS AND DOORS USING GALVANISED M.S.WIRE GAUGE WITH AVERAGE WIDTH OF APERTURE OF 1.4 MM IN BOTH DIRECTIONS WITH WIRE OF 0.63 MM DIA.

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, pre moulded and pre polished, machine cut granite for kitchen platforms, laid over 20 mm thick base cement mortar 1:4 finish

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position : Sal wood

Providing and applying white cement based Putty of Average thickness 1 MM of approved brand and manufacturer over the plastered wall surface to prepared the surface even and smooth complete.

MAHALAXMI CONSTRUCTION COMPANY