Renovation of Barrage-Civil office complex, Sewerage system and other miscellaneous work, TLD-III PS

Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. In ground floor including roof.

Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. Extra rate for each addl. Floor over the rate of ground floor.

Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed.

25 mm. thick damp proof with cement concrete (1:1.5:3) (with graded stone aggregate 10 mm. normal size) and painting the top surface with a coat of bitumen [VG.40 ] using 1.7 kg. per sq.m. including heating the bitumen and cost and carriage of all materials complete. [Bitument to be supplied by the Agency].

Supplying, fitting and fixing porcelain toilet paper holder of approved make with wooden spindle as necessary. Recess roll type size 150 mm X 150 mm.

Supplying,fitting & fixing 1st quality Ceramic tiles in wall and floor to match with the existing work & four nos of key stones (10 mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface if necessary or by synthetic adhesive & grout materials etc.-WWiitthh PPoloylmymereirsiesded AdAhdeshievseive & Eapnodxy Egproouxyt pogirnotiuntg pointing including spacer- 2 mm ( When Tiles are laid over existing hard ready surface)-Area of each tile upto 0.09 Sq.m [using adhesive 3 mm thick]-Coloured decorative. In wall- Coloured decorative.

Supplying fitting and fixing Cast iron soil pipe only confirming to IS 3989 /1970 and IS 1729 /1964 with bobbings nails etc including making holes in the wall ,floor etc. and cutting trenches etc. in any floor through masonry concrete if necessary,and mending good damages with necessary jointing materials and painting two coats to the exposed surface with approved paint complete(measurement will be made along the center line of the total pipe line in fitted condition including specials ,payment for specials & painting will however be paid seperately). With valamoid joints including sealing with sand cement mortar (4:1) upto quarter depth. 100 mm dia.( internal).

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints or roughening of concrete surface, including throating, nosing and drip course where necessary (ground floor) With 1:4 cement mortar. 10 mm thick plaster

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints or roughening of concrete surface, including throating, nosing and drip course where necessary (ground floor) With 1:6 cement mortar. 15 mm thick plaster

Supplying,fitting & fixing 1st quality Ceramic tiles in wall and floor to match with the existing work & four nos of key stones (10 mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface if necessary or by synthetic adhesive & grout materials etc.-Floor-With Polymerised Adhesive and Epoxy grout pointing including spacer- 2 mm ( When Tiles are laid over existing hard ready surface)-Area of each tile upto 0.09 sqm--Floor -Coloured decorative.

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. in cluding using of approved putty etc. on the surface, if necessary On timber or plastered surface with super gloss(hi-gloss) of approved quality Two coats (with any shade except white).

Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Wood work in door and windows frame fitted and fixed complete including a protective coat of painting at the contact surface of the frame excluding cost of concrete ,iron butt hinges and MS Clamps .(the quantum should be corrected upto three decimals). Sal Siliguri

Z-batten shutters of door and window as per design havings tongued and groove -half lap jointed as per direction of the Engineer-in-Charge including fitting and fixing shutter in position ,but excluding the cost of hinges and other fittings in ground floor. Shutter with 19 mm thick planks ,19 mm thick battens.

Supplying, Fitting & Fixing 30 mm thick both side prelaminated Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top,bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel using PVC solvent adhesive etc. complete excluding all necessary hardwares as per direction of Engineer-in- Charge.

Supplying fitting and fixing G.I. of TATA make with all necessary accesaries specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes,making threads fitting,fixing etc. complete in all respect including cost of all necessary fittings as required, jointing materials and two coats of painting with approved paint in any position above ground ( Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accessories, specials.) a(ii) 15mm dia. medium quality

Ordinary cement concrete Nominal (mix 1:2:4) Cement concrete with graded stone chips (20mm nominal siz

e) excluding shuttering and reinforcement.if any in ground floor as per relevant IS Code. River Bazree.

Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

125 mm thick brick work with 1st class bricks in cement mortar (1:3) in ground floor

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. in cluding using of approved putty etc. on the surface, if necessary On timber or plastered surface with other than hi-gloss of approved quality Two coats (with any shade except white)

White washing including cleaning and smoothening surface thoroughly, All floors:Two coats.

Stone Boulder 150 mm of N. Bengal variety (Materials delivered and stacked at site).

Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm

Note: 1. All applicable taxes & duties including GST, other levies and charges etc. on above item have been mentioned in this schedule. The reimbursement of total taxes & duties shall be restricted to the total amount in 8 of this schedule subject to Clause No.2.4 of Terms & Conditions of Contract (T&C). 2. It is hereby confirmed that, except as otherwise stipulated in the Tender Specification and the statutory variations permitted as per the Contract, the above unit rates and other charges as mentioned in this Schedule, will remain firm till the subject supplies are complied. Further, it is confirmed that no other charges would be payable by NHPC, in connection with our execution of the resultant Purchase Order. 3. The “Contract price” shall mean the total Price mentioned in Col.11.