SPL REPAIR/REPLACEMENT OF FURNITURE FOR OTM ACCN AGAINST BER FURNITURE AT GE I GOS AT GMS

Amount

Table Centre 2 tier with Glass Top (FD/E6/MAP/08): Overall size shall be 900mm long, 450mm wide and 400mm high. a) All wood to be used shall be 1st class hard teak wood. Irrespective of what is shown on drg, the top of table shall be 18mm thick BWR plywood of Grade-A with 1mm thick laminated sheet pasted over the ply with marine grade adhesive and all edges of top shall be covered with 6mm thick teak wood beading.Irrespective of what is shown on drg, one center stiffener of size 20mmx50mm shall also be provided length wise at center in between the side bottom rails 25mm dia hard rubber/PVC rings shall be fixed to the bottom of all legs with 20mm long screws. Rest all specifications and dimensions are as per drg. All wooden surface shall be polished in high gloss melamine finish of walnut shade after preparation of surfaces complete all as specified and directed.

Chair writing Steel (FD/E6/MAP/12): The overall size of the chair shall not be less than 475mm wide and deep and 580mm high at seat from ground level. The seat and back are to be made up of 1.2cm thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded melamine foam. The back foam is to be designed with contoured lumbar support for extra comfort. The foam is to be moded with density =45+/-2 kg/m3 and Hardness= 20+/-2 at 25% compression. Arm rest shall be one piece. All metel parts shall be dry powder coated in thickness more than 50 microns complete all as specified and directed.

Chair Dinning PVC (MAP) (FD/E6/MAP/03): All woodwork shall be of 1st class teakwood of special Tectona Grandis conforming to IS-1331:1971 free from knots and cracks shall be used with moisture content permissible as per IS:287:1973. The seat shall be PVC 4mm thick visible like Godrej pattern with 4x10mm thick ribs moulded alongwith seat in single piece screwed with seat frame as shown in drawing. Nylon buffers of appropriate size to bew provided to all the four legs of the chair. All exposed wooden surface shall be smootherned before applying french polish till it attains glossy finish. All joints fixing shall be fixed with bamboo pins and nails shall not be used. Rest all as per drgs or complete all as specified and directed.

Table Dressing Ladies with Stool (FD/MAP-II/07): The overall size of the table dressing shall be 1150mm long 380mm wide and 1700mm high and Overall size of the stool shall be 440mm wide. It shall be made up of BWR plywood of grade-A of specified thickness as per drg in lieu of prelaminated particle board.1mm thick laminated sheet shall be pasted on all exterior surface with marine garde adhesive including 6mm thick teak wood beading shall be provided alround the edges of shutters and drawers. Drawers shall be provided with 2x Nos of inch long stainless steel telescopic channels.Drawer and shutter shall be provided with 90mm long recessed metal handles and shutter to be provieded with magnetic catches. Looking mirror shall be 5mm thick electro copper plated fixed over 6mm thick plywood back. 4x Nos heavy duty double wheel castors shall be provided at bass ply. The seat of the stool shall be 75mm thick, 40 density foam cushion covered with best quality tapestry cloth of rate not less than 450 per mtr rest all specification and dimesions are as per drg or complete all as specified and directed.

Bath Stool PVC (FD/E6/MAP/07): The verall size of the bath stool PVC shall be 400mm L x 300mm W x 250mm H.The bath stool PVC shall be made up of 5mm thick PPCP m,aterial. The bath stool PVC shall have centre leg of dia 25mm. The four leg shall be in arc shape and of size 100mm x 100mm. The top of the bath stool shall have 3mm x 10mm thick stiffner molded along with the seat in single pieace underneath. The weight of the bath stool shall not be less than 1.3 Kgs.

Charpoy Folding (FD-388 (R)): All as shown on drawing. Overall size shall be of 1980x900x550mm.The frame work shall be 25mm dia 16 guage MS conduit pipe.04 nos stiffner shall be provided between long rail 25mm dia 16 guage .Top shall be of 8mm thick BWR plywood conforming to IS-303. Rest all as shown on drawing. All joints/weldings/fixing shall be done in accordance with standard workmanship. All frame work shall be painted with spray paint synthetic enameled over a coat of primer complete all as specified and directed.

Receptical PVC (FD/E6/MAP/13): All as shown on drawing. Overall size Receptical shall be of capacity 20 ltr . The body of receptical PVC shall be made up of thick polymet plastic of thickness not less than 2.5mm provided with swivel lid and iron handles on both sides as shown in drg or complete all as specified and directed.

Almirah Large Steel 1/2hx1/2S (FD-1043): All as shown on drawing. Overall size shall be 920mm long, 485mm wide and 1985mm high. The base shall be 100mm high. The base shall be made of two numbers mild steel sheet channets shape with ends covered and welded to bottom of almirah. Mild steel sheet for channel shall be 1mm thick. the base channel shall be welded at 50mm from each end of 920mm length . Top sides back, bottom and front of almirah shall be 1mm thick mild steel sheet. Two shelves shall be provided at 350mm and 700 from bottom of almirah. A hanging rod 60mm from top shall be provided which shall be of 20mm dia steel chromium plated conduit pipe of wall thickness 1.25mm two sockets shall be provided at the end of hanging rod. Front shutters shall have two leaves .A steel chromium plated handle 100mm long shall be provided to shutters, A three way locking device shall be provided to front shutters. Each leaf of front shutter shall be hinged with three numbers butt hinges 75mm long and shutters shall be side hung. All joints and welding, fixing shall be done with standard workmanship. All steel surfaces exposed to view when placed in position shall be given two coats

Table Dressing Gents With Glass (FD/E6/MAP/16): Overall size shall be 1200mm high, 600mm wide and 100mm high. All wood to be used shall be 1st calss hard teak wood. It shall be made up of BWR plywood of grade-A of specified thikness as per drg in lieu of prelaminated particle board. 1mm thick laminated sheet be pasted on all exterior surface with marine grade adhesive including 6mm thik teak wood beading shall be provided alround the edges of shutters and drawers. Looking mirror shall be 5mm thick fixed inside the teak wood frame made out of 38mmx25mm section. 03x glass shelves of 5mm thickness shall be fixed inside the box with glass holders as shown in drg. Rest all specification and dimensions are as per drg. Preparation of surfaces shall be polish in high gloss melamine polish.

Chair Revolving with H/B cushion, Godrej Modle PCH-7022: As per Trad patteren

Filing Cabinet Size 1375x960x628mm Make Godrej: As per Trad patteren

Trestle Store room Steel (FD-1043): THIS DRAWING SUPERSEDED DRAWING NO. FD-86(M) SHEET 1/1 FOR TRESTLE STORE ROOM ( STEEL) ONLY. All as shown on drawing . Overall size shall be 2440mm long, 600mm wide and 300mm high. Two long angle iron 40mmx40mmx600 of mild steel 1980mm long shall be provided 520mm apart at bottom connected with 50mmx300 flat iron bracing, four in numbers, and equally spaced with 50mmx50mmx6mm T-iron. Two flat iron mild steel bracing of 50mmx3mm shall be provided as a cross bracing joining vertical T-iron provided at four equally spaced members of T-iron. Two long mild steel angle iron 40mmx40mmx6mm of 2440mm long shall be provided at top. Two short mild steel angle iron 40mmx40mmx600 of 600mm Tength shall be proveded at both the ends of trestle. Two numbers50mmx50mmx6mm T-iron 600mm long be provided equally spaced joining two long angle iron. Four cross bracings at top shall be provided with 50mmx3mm mild steel flat iron bracing. Four mild steel flat iron stuts shall be provided to each side of the trestle. All jointing, welding and fixing shall be done in accordancewith standard workmanship. all Steel and iron work surfaces shall be painted with two coats of enamel paint over a coat of primer with spray after prepration of steel surfaces on esposed to viev when placed in position.

Sofa set 5 seater with cushion (FD/MAP-II/02): Overall size of three seater shall be 1730mm wide, 725mm deep and 530mm high up to arm level and one seater shall be 670mm wide and 725mm dee and 530mm high up to arm. All wood to be used shall be 1st class hard teak wood. Soda set five seater shall consist of one three seater and two single seats. 10xNos of foam cushion to each set each of size 530m,mx560mmx100mm thick of 40 density coverd with white lining cloth and best quality tapestry cloth of rate not less than 450 per mtr shall be provided with nylon zipper at one edge duly covered under the tapestry cloth flap. PVC hard rubber shoes of 25mm dia shall be provided to bottom of each leg with 20mm long screws.All wooden surface shall be polished with high gloss melamine polish in walnut shade after preparation of surface. Rest all specification and dimensions are as per drg or complete all as specified and directed.

Bed Hard steel offrs (FD/E6/MAP/08R): All as shown on drg and specification Conduit pipe shall be 38mm sq 1.6mm thick for main frame and 19mm sq 1.6mm thick for inner frame for head and foot board 65mmx25mm 1.6mm thick for long rail. 25mm sq 1.6mm thick for stiffener under 12mm plywood shall be used Prelaminated particle board 18mm exterior grade for head and foot board with PVC edging 1mm thick. Finish : All steel surface shall be black powder coating Rest all as shown on drg or complete all as specified and directed.

Ladder Aluminium (FD-1025): Dimension : Overall size shall be 2310 mm long, 363.5mm wide. Description : a) The ladder shall be of aluminum stringer having size 60mm x 31.75mm and wall thickness 3.18mm . b) Each rung shall be of 23mm dia aluminum pipe with wall thickness not less than 2.43mm and shall be eight in nos placed at equidistant spaces of 300mm in between as shown in drg. c) Each aluminum pipe rung of 23mm dia shall be fitted inside the stringer with end bend to shape and each rung on both sides shall be provided with hard rubber cap . d) Hard rubber caps/shoes shall be fixed at the ends of aluminum rungs and stringers as shown on drawing with screws . Rest all specifications and dimensions are as per drg or complete all as specified and directed.

Table Dining 8 pers (FD/MAP-II/03): The overall size of the table shall be 2100x900x760mm. The table top shall be of 18mm thick pre-laminated particle board exterior grade confroming,exterior qulity as per IS:14587:1998. All woodwork shall be of 1st class teakwood of specie tectona grandies conforming to IS-1331:1971 free from dead knots and moisture content as permissible as per IS-287. 6mm thick TW lipping shall be provided on all the exposed of MDF Duly treated with french polish as specified. Powder coated MS angular plates each of 150mmx30mmx5mm thick shall be screwed to the legs as right angles with long rails and short rails. Hard nylon shoes/buffers shall be provided to each leg bottom.

DEBASHIS AGENCY

M/s Bapujee Builders and Traders

ABC CONSTRUCTION COMPANY

Capital Construction Company