Work No. 16

Amount

Earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift upto 1.5 Mtr. Including taking out the excavated soil and depositing and refilling of jhiri with watering and ramming and disposal of surplus excavated soil as directed within 50 m. in all kinds of soil.

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work upto plinth level 1: 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Brick masonry in foundation and plinth with bricks of class designation 75 in Cement mortar 1:6 upto third storey.

Half brick masonry in foundation & plinth using bricks of designation 75 in Cement mortar 1 : 4 ( 1 cement : 4 coarse sand):

Brick masonry in Super Structure up to third story with bricks of class designation 75 in cement mortar 1:6

Filling local sand in trenches, plinth, side of foundation, under floors etc. in layers not exceeding 20 cm in depth consolidating each deposited layer by ramming and watering including all leads and lifts.

Centering & shuttering with plywood or steel sheets including strutting, propping, bracing bothways and removal of formwork for superstructure upto 4.5m. height above plinth level for : (a) suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, copings, bed plates, anchor blocks, sills, chhajas lintel beams etc.

Reinforced cement concrete work in beams, suspended floors, roofs, girders having slopes up to 15o , landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases, up to floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1-Cement:3-coarse sand) and making good and joints excluding the cost of centering, shuttering and reinforcement: 1:1.5:3 (1-Cement:1.5 coarse sand:3-graded stone aggregate 20 mm nominal size).

Providing & fabricating reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete upto floor three level hot rolled deformed ( IS : 1139) bars.

Providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section joints mitered and welded with steel lugs 13 x 3 mm, 10 cm long embedded in cement concrete block 15 x 10 x 10 cm. Of 1: 3: 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm .nominal size) or with wooden plugs & screws or rawl plugs and screws with fixing clips or with bolts & nuts as required including providing and fixing plane glass panes 4 mm thick with copper glazing clips & special metal sash putty of approved make or metal beading with screws complete including priming coat of approved steel primer, excluding the cost of metal beading & other fittings except necessary hinges of pivots steel handles peg stays etc. as required as per IS:1038. Windows side hung (openable)

S & F fixed wiregauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20 x 3 mm with suitable screw at not exceeding 150 mm distance

Providing and fixing Square bars or other flat welded to window, ventilators etc.

Providing & fixing external grade board, solid core single leaf flush door shutters IS : 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure 'A' : 30 mm thick Commercial veneer both side

Plaster on new surface on wall in cement sand mortar 1 : 4 including raking of joints etc. complete fine finish, 12 mm thick.

Providing 100 mm thick average mud phuska damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with phuska at 35 Kg./cum of earth, gobri leaping with mix 1 : 1 ( 1 clay : 1 cow dung) and covered with flat tiles of class designation 100 grouted with cement mortar 1:3,mixed with 2% integrated water proofing compound by weight of cement and finished neat.

Pointing on brick or tile masonry in cement sand mortar 1 : 3 ( 1 cement : 3 sand) flush or ruled pointing.

Providing and fixing 1st quality MAT Finished Ceramic tiles size 300 x 300 mm confirming to IS 13755 coloured tile except white, grey, Ivory, fume red brown in walls ,floors, steps, pillars etc. laid on a bed of neat cement slurry including nicely finished joints using water proof joint filler powder (Unitile or Roffe make) finishing with flush pointing in white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster).

Providing and fixing Ist quality standard White Ivory Glazed Tiles ISI marked [IS:13753] of size 300mm x 200mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in white cement mixed with pigment to match the shade of tile complete (excluding the cost of cement plaster) : Category-I : Kajariya, Jhonson, Orient, Somani make etc.

Demolishing brick work including stacking of serviceable material and disposal of unserviceable material within 50 meters lead. : In Cement mortar.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding .new work (two or more coats) over and including scrapping and priming coat with distemper primer.

Finishing wall with water proofing cement paint of approved brand and manufacture and or required shade to give and even shade including all scaffolding new work (Three or more coats)

Providing and laying in position cement concrete including curing compaction etc. of specified grade excluding the cost of centering and shuttering =All up to plinth level : 1:1.5:3 (1Cement :1.5 Course Sand :3 Graded stone aggregate 20 mm nominal size

Painting with enamel paint of approved brand and manufacture to give and even shade two or more coats on new work.

P & F indian type white glazed vitreous china 1st quality W.C. Orissa pan ( I.S. : 2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor. Size 580 x 440mm

P & F White vitreous china double syphonic Europeon W.C. ( I.S. : 2556 Mark) with mounted W.V.C. flushing cistern of (I.S. : 2556 Mark) of 10 litre capacity complete with all necessary internal fittings including cutting and making good the wall and floor

P & F 1st quality WVC Urinal (IS : 2556 mark) with 25mm dia G.I. Waste pipe, dome couplings, concealed iron brackets or screws etc.) Flat back (large) or half stall size 590x375x390mm

P and F WVC urinal partition plate of approved standerd make of size 630 x350 x mm including making good the wall

P & F WVC squatting urinal of standerd make complete including cutting & making good the floor Size 600 x 350 mm

P & F WVC wash basin (1st quality, I.S. : 2556 Mark) of approved make with C.I. Brackets duly painted, 1 NO 15 mm C.P. Pillar cock (I.S. : 8934 mark) & 32 mm C.P. brass waste coupling of approved make, 25 mm G.I. Waste pipe complete including cutting & making good the wall. Size 550mm x 400mm

P & F Beveled edge Mirror of special glas of approved make ( Atul/equivalent) complete with 6mm thick asbestos cement sheet ground fixed to wooden screws & washers. Size 600 x 450 mm x 4mm thick

P & f towel rail or ring of approved quality make : CP Brass towel ring revolving type

P & F Soap dish or tray of approved quality /make : CP Brass

P & F G.I. Pipes (Internal Work) with G.I. Fittings (IS : 1239 Mark) & MS clamps, including cutting and making good the walls and floors exposed on wall : "A" Class 40mm

P & F Bib cock ( IS : 8931 Mark) Superior quality of approved make : Brass 400gm 15mm nominal bore.

P & F Ball Cock (IS:1703 Mark) with Rod & P.V.C. ball complete : Brass wt. 1000 gm 25 mm.

P & F Inlet connection (Angle, valves) Superior quality, of approved make for wash basin, Gyser etc.. C.P. Inlet connection 15mm Brass (IS 8931 marked)

P & F 15 mm dia connection pipe of approved quality/make :P.V.C. Pipe with nut length upto 300 mm.

P & F Flush Cock/Flush Valve (IS:9758 Mark) for WC of approved quality make :Brass/Gun metal Half - turn wt. 1 Kg. Of approved quality /make. 25 mm

P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make : Gun metal 25 mm nominal bore

P & F PVC storage tank confirming to (IS 12701 indicating the BIS license No.) of approved make with cover, 25mm dia 1 M long G.I. Over-flow pipe & 25 cm. long wash out pipe with plug & socket, including making connection etc, complete of approved design :1000 liters capacity

P & F rigid PVC pipe (IS : 4985 mark) class II (4 Kg Per. Cm.2 approved quality/make including jointing the pipe with solvent cement rubber ring and lubricant 110mm dia.

size 450 x 450 mm depth upto 0.5 M & 5 Kg.CI cover with frame.

Construction of Septic tank in all types of soil with 40cm. Thick masonry in CM 1:6,15 Cm. Thick C.C. bed of 1:5:10, M-15 grade C.C. Flooring & over stone slab convering , 80 mm thick slab, jointing of slabe in CM 1:3 ralthal, kharanja, 50mm thick stone partition wall s, 20 mm thick plaster in cement mortar 1:6 finished with floating neat cement, 4nos CI footrestof approved design , 2 nos 450 mm dia 25 kg CI cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 m. size 400x140x150 cm. : Size 400 x 140 x 150 cm. (for 50 users)

Supplying and fixing CI covers with frame, gratings for chamber & manhole

Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) of approved make in surface / recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's accessories, round tiles,18 SWG M.S. box with earth terminal, screwless cage connectors for neutral looping in switch board & false ceiling point, 6 A switch, 3.0 mm thick ISI marked phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required. Short point (up to 3 mtr.)

Medium point (up to 6 mtr.)

Long point (up to 10 mtr..)

Wiring of 3 pin 5 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) of approved make in surface / recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's accessories, 18 SWG 175 mm x 100 mm x 60 mm M.S. box with earth terminal, screwless cage connectors for neutral looping in switch board , 6 A switch, 6 A socket, 3.0 mm thick ISI marked phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required. On board

Long point (up to 10 mtr..)

P&F Recessed/ Surface mounting heavy duty horizontal type sheet steel Distribution board phophatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link and din bar,masking sheet, conforming to IS13032 & IS8623 including making internal DB terminations with copper lugs , testing etc. as require : Double door (single phase) : 6 Way

P & F ISI marked 6 amp. Bakelite batten / angle holder including making connection testing etc. as required G-II.

S & F following sizes (dia.) of ISI marked medium duty PVC Conduit along with accessories in surface / recessed using saddles, clamps, fasteners, as required including cutting the wall and making good the same as required : 25mm G-II

P & F 18 SWG Sheet steel boxes duly finished ith two coats of red oxide and with earthin terminal of following sizes ( nominal size ) on surface or recessed as required : 200mm x 150 mm x 60mm

P & F 240/415 V isolator confirming to IS : 13947-III / IEC 60947-3 on existing board / sheet including making connections with lugs, testing etc. as required.

P & F 240 / 450 V MCB of breaking capacity not less than 10 KA ( B / C / D tripping characteristic ) ISI marked IS : 8828 ( 1996 ) conforming to IEC 60898 in existing board / sheets including making connections with lugs, testing etc. as required : Single pole MCB 6 A to 32 A rating

P&F ISI marked (IS : 3854) 16 amp. Flush type switch including cutting hole in tile and making connection testing etc. as required

P&F ISI marked (IS : 1293) 3/6 pin 16 amp flush type socket including cutting holde in tile and making connection testing etc. as required

S& Laying following size earth wire/strip in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc, as required

S&F drawing FR PVC insulated & unsheahed flexible copper conductor ISI marked (IS:694) of 1.1 kV grade and approved make in existing surface or rexessed conduit/casing capping including making connectons etc. as required : 2X2.5 sq. mm + 1X1.5 Sq. mm

Providing and laying factory made chamfered edge Plastic coated Designer Cement Concrete paver blocks of required strength, thickness and size/shape, made by table vibratory method, to attain superior smooth finish using PU or equivalent moulds, laid in required Grey/ Yellow/ Red or any other colour and pattern over 50 mm thick compacted bed of Coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per manufacturer's specifications and direction of Engineer-in-charge. '- do- 80 mm thick C.C. Paver block of M-30 grade with approved color design and pattern.