NIT No. 541/TC/EinC/PWD/26-27

Drainage Spouts complete as per drawing and Technical specification of section 2705.

Painting on kerbs in black and yellow alternate bands including cost of material and labour complete as per drawing and specification as per clause 803. With Road Marking Paint

Providing and Fixing of Av. 20mm thick marble plate i/c cutting and polishing and inscribed details as per approved drawing i/c engraving.

Providing and fixing for hand railing top of crash brier including cost of material complete as per approved drawing

Mastic Asphalt Providing and laying 25 mm thick mastic asphalt wearing course with paving grade bitumen meeting the requirements given in table 500-39, prepared by using mastic cooker and laid to required level and slope after cleaning the surface, including providing antiskid surface with fine grained hard stone chipping of 13.2 mm nominal size pre- coated with bitumen at the rate of 0.005cum per 10 sqm and at an approximate spacing of 10 cm center to center in both directions, pressed into surface when the temperature of surfaces not less than 100 deg. C, protruding 1 mm to 4 mm over mastic surface, all complete as per clause - 515.

Bituminous Concrete (Providing and laying bituminous concrete with minimum 40-60 TPH capacity hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.0 to 6.0% by weght of total mix of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects) B With mechanical paver finisher (iii) for Grading II (13 mm nominal size) with bitumen 6.0 %

Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.) I Ordinary soil A Manual Means (i) Upto 3 m depth

Plain/ Reinforced cement concrete in open foundation complete as per drawing and technical specification. A Using concrete mixer (i) PCC Grade M-15

(iii) PCC Grade M-25

Supplying, fitting and placing un-coated HYSD bar reinforcement in foundation complete as per drawing and technical specification as per section 1600. Wall @ 10kg/Cum

Construction of embankments / Sub grade with material Obtained from Borrow Pits (Construction of embankment with approved material / salected soil having C.B.R. > 5 (unless specified otherwise in the contract0 obtained from borrow pits with all lifts and lead, transporting to site, spreding, grading to required slope and compecting to meet requirement of table 300-2)

Granuler Sub-base as per table :- 400-1 Construction of granuler sub-base by providing close graded Material, carriage of mixed Material to work site spreding in uniform layers with motor grader on prepared surface watering rolling and compacting with vibratory power roller at OMC to achieve the desired density, complete as per clause 401. A Plant Mix Method method (i) for grading- I Material

Wet Mix Macadam (Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per clause 406.)

Primer coat (Providing and applying primer coat with oil based bitumen emulsion (SS-1) on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.85 kg/sqm using mechanical means.

Tack coat Providing and applying tack coat with bitumen emulsion (RS-1grade confirming to IS 8887)) using emulsion pressure distributor on the prepared bituminous/granular surface cleaned with mechanical broom and as per clause 503 of section 500 of section 500. (ii) Dry and hungry bituminous surfaces/ granular surfaces treated with primes @ 0.30 kg / Sqm

Dense Graded Bituminous Macadam (Providing and laying dense bituminous macadam with minimum 40-60 TPH capacity HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 to 4.5% by weight of total mix of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher to the required grade, level and alignment rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORT&H specification clause No. 507 complete in all respects.) (i) for Grading I(40 mm nominal size, bitumen content 4.25%)

Semi - Dense Bituminous Concrete (Providing and laying semi dense bituminous concrete with 60-90 TPH using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 % of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORT&H specification clause No. 508 complete in all respects) B With mechanical paver finisher (i) for Grading I(13 mm nominal size), bitumen content 4.50%)

Providing and fixing Guard stones 200x200x900mm made of precast RCC M20 grade fixed at 300 mm into the ground in P.C.C. 1:3:6 blockes of size 400x400x400 mm and given two coats of paint with white and black bands including excavation.

Providing and laying Pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and Technical specifications

Providing and laying Filter material underneath pitching inslopes complete as per drawing and Technical specification

Retro- reflectrorized Traffic signs (Providing and fixing of retro- reflectrorized cautionary, mandatory and informatory sign as per IRC :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 1.5 mm thick supported on a mild steel frame of size 40 x 40 x 5 mm and mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing) (ii) 60 cm equilateral triangle

( iii ) 60 cm circular

( iv ) 80 mm x 60 mm rectangular

Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35-1997. The finished surface to be level, uniform and free from streaks and holes.)

Providing & Fixing Hazard Marker Type-2 Partial Retro Reflective Size 0.30 x 0.90M made of 16 gauge (1.6 mm) thick mild steel sheet Confirming to IS:2062 Painted with one cast of Zinc Chromate Stoving Primer and two coats of Black Stove Enamel (Oven Baked) paint with 10 cm bands of yellow Retro- Reflective Sheeting of Engineering Grade pasted a per IRC:79-1981 including one MS angle Iron post of size 50x50x5 mm of 1.65 meter long duly painted with synthetic enameled paint block including bolts and fixing the same in M-15 concrete black of size 30x30x30cm, including transportation etc. Complete.

Metal Beam Crash Barrier A Type - A, "W" : Metal Beam Crash Barrier (Providing and erecting a "W" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanized by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 810)

PCC 1:3:6 in Foundation (Plain cement concrete 1:3:6 mix with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.)

Providing and laying Plain/Reinforced cement concrete in sub-structure complete as per drawing and technical specifications section 1500, 1700 and 2200 A Height upto 5m (a) Using concrete Mixer (i) P.C.C. Grade M-15

Providing and laying Reinforced Cement Concrete pipe NP 3 / prestressed concrete pipe on first class bedding. (Laying Reinforced cement concrete pipe NP3 /prestressed concrete pipe for culverts on first class bedding of granular material including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets . ) C 900 mm. dia.

Providing and laying boulder apron on river bed for protection against scour with stone boulders weighing not less then 40 kg each complete as per drawing and technical specifications as per relevant clauses of section 2503.

UOM Name

Percentage

Per mile

Siemens Per meter

Activity unit