REPAIR/REPLACEMENT OF JOINERY, PLUMBING, TILING, SANITARY FITTING, STEEL GATE, ROLLING SHUTTER ETC IN DGQA AREA UNDER AGE B/R-I OF GE (I) KANPUR CANTT

Amount

Taking down chowkhats or frame n.exc 1.50 sqm with shutters (wihtout taking off shutter from frame ) etc complete all as specified and directed.

Taking down chowkhats or frame exc 1.50 sqm but n.exc. 4.00 Sqm each with shutters (wihtout taking off shutter from frame ) etc complete all as specified and directed.

Taking down shutter exceeding 1.00 Sqm but not exceeding 2.0 Sqm each complete all as specified and directed.

All as item 3.00 above but area not exceeding 1.0 Sqm each complete all as specified and directed.

M&L 2nd class HW as in plain , solid, straight chowkhats and frames , wrought , framed , rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F of 30 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. Note : Manufacturer test certificate and PVrs shall be submitted by contractor before claiming payment against this item.

S&F 19/20mm thick Particle board, exterior grade prelaminated both sides with decorative choice lamination, fixed with nails/ screw screws to timber/steel frame work as in shutters, shelving to cup boards etc including 6 mm thick teak wood lipping complete all as specified and directed.

Material & Labour two coats of synthetic enamel paint over and ncluding a coat of pink primer to new wooden surface of any description over 10 cm width or girth including preparation of new surface complete all as specified and directed.

S&F MS butt hinges medium weight cold rolled of 100 mm size.complete all as specified and directed.

S&F continuous (piano) hinges, of mild steel (chromium plated) of 40mm width of flaps (when open0 complete all as specified and directed.

S&F of 200 mm long barrel tower bolt aluminium anodised of extruded section complete all as specified and directed.

S&F of 150 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F aluminium hasp & staple safety type 100mm size complete all as specified and directed.

S&F of 300 mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

M&L for powder coated aluminium glazed window shutters with frame openable, section for aluminium frame 100 x 45 x 2.00mm thick & section for shutter 45 x 44.45 x 1.90 mm thick including 5mm thick tinted glass sheet with rubber beading clip, hinges, handles, tower bolts etc complete all as specified and directed.

M&L for powder coated aluminium glazed window shutters with frame openable, section for aluminium frame 100 x 45 x 2.00mm thick & section for shutter 45 x 44.45 x 1.90 mm thick including provision of opening for window AC opening and 5mm thick tinted glass sheet with rubber beading clip, hinges, handles, tower bolts etc complete all as specified and directed.

S&F for powder coated Aluminium door partly glazed (using 5mm thick glass) and partly panelled or fully Glazed (using 12mm thick both side prelaminated board Noavapan Kitlam) door with bottom rail of section 114x44.5x1.5mm thick and middle and top rail and style of section 84x44.45x 1.5mm thick including 125mm dia circular aluminium handle tower bolt, mortice lock of brass size 65mm, vertical type with fair levers door stopper double leg rubber beading and door spring, two numbers door stopper, hinges (three Nos each side) etc and aluminium frame of section 100x44.45x2.00mm thick complete all as specified and directed.

M&L for powder coated aluminium grill of mesh size 65 x 75mm of 6mm dia of aluminium bar fixed with 'Y' or 'H' aluminium section complete all as specified and directed.

M&L for aluminium anodised glazed window shutters with frame openable, section for aluminium frame 100 x 45 x 2.00mm thick & section for shutter 45 x 44.45 x 1.90 mm thick including 5mm thick tinted glass sheet with rubber beading clip, hinges, handles, tower bolts etc complete all as specified and directed.

M&L for aluminium anodised glazed window shutters with frame openable, section for aluminium frame 100 x 45 x 2.00mm thick & section for shutter 45 x 44.45 x 1.90 mm thick including provision of opening for window AC opening and 5mm thick tinted glass sheet with rubber beading clip, hinges, handles, tower bolts etc complete all as specified and directed.

S&F for Aluminium anodised door partly glazed (using 5mm thick glass) and partly panelled or fully Glazed (using 12mm thick both side prelaminated board Noavapan Kitlam) door with bottom rail of section 114x44.5x1.5mm thick and middle and top rail and style of section 84x44.45x 1.5mm thick incl 125mm dia circular aluminium anodised handle tower bolt, mortice lock of brass size 65mm, vertical type with fair levers door stopper double leg rubber beading and door spring, two numbers door stopper, hinges (three Nos each side) etc and aluminium frame of section 100x44.45x2.00mm thick complete all as specified and directed.

M&L for aluminium anodised grill of mesh size 65 x 75mm of 6mm dia of aluminium bar fixed with 'Y' or 'H' aluminium sec complete all as specified and directed.

Dismantling of aluminium partition in any description incliuding glass and board complete all as specified and directed.

S&F powder coated aluminium partition with aluminium tube of section 114x44.45x1.90mm thick at bottom and remaining vertical and horizontal rails of section 44.45x45x1.9mm thick and top rail of section 44.45x45x1.90mm thick with aluminium anodized clips, rubber, beading, aluminium angle, nut bolt etc (from bottom 75cm height/Novapan/Kit Lam both side laminated 12mm thick ISI marked and remaining parts of partition shall be covered with plain float glass of 5.0mm thick (maximum spacing of glazed aluminium tube in horizontal 75cm C/C and in vertical 120Cm C/C ) complete all as specified and directed.

S&F aluminium anodised partition with aluminium tube of section 114x44.45x1.90mm thick at bottom and remaining vertical and horizontal rails of section 44.45x45x1.9mm thick and top rail of section 44.45x45x1.90mm thick with aluminium anodized clips, rubber, bading, aluminium angle, nut bolt etc (from bottom 75cm height/Novapan/Kit Lam both side laminated 12mm thick ISI marked and remaining parts of partition shall be covered with plain float glass of 5.0mm thick (maximum spacing of glazed alu tube in horizontal 75cm C/C and in vertical 120Cm C/C ) complete all as specified and directed.

M&L solid PVC frame ( single rebated) of size 50 mmx 47 mm made oud of 5mm plain colour PVC sheet with homogenious fine cellular structure having smooth outer integral skin with suitable metal stifner & fixed with 100x8 sheet metal CSK (copper screws)screws complete all as specified and directed.

M&L factory made solid panel PVC moulded door shutter with wood free EPS 28 to 30 mm thick (style) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plan colour PVC sheet on back face, supply & fix in frame at site complete all as specified and directed.

S&F 100 mm long PVC butt hinges complete all as specified and directed.

S&F 150 mm long PVC handle complete all as specified and directed.

S&F 150 mm long PVC barrel tower bolt complete all as specified and directed.

S&F factory made uPVC white colour casement (openable) window area exc 1.00 Sqm but not exc 2.00 Sqm made of extruded profiles with wall thickness of 2.3 mm (+ 0.2mm) window profile with hollow section with multichamber ,frame (60mm X58 mm) sash (60 mm X 73 mm) T profile (one vertical length in between two shutters) (60 mm X 74 mm) glazing bead (35 mm X 20mm ) will be mitered cut and fusion welded at all corners including drilling of holes for fixing hardware and drainage of water etc making arrangement for fixing of hardware EPDM gasket 1.2 + 0.2 mm thick galvanized steel frame (28mm X 21.5 mm ) sash (31mm X 27.5 mm ) T profile (27mm X 17 mm ) to be inserted in required profile, frame will be fixed to the wall with 8 mm X 100 mm long fasteners included casement handle made of zinc alloyed (white powder coated) transmission gear made of mild steel with multe point locking system complete all as specified and directed.

S&F factory made uPVC white colour casement (openable) Door area exc 2.00 Sqm made of extruded profiles with wall thickness of 2.3 mm (+ 0.2mm) window profile with hollow section with multichamber ,frame (60mm X58 mm) sash (60 mm X 78 mm) T profile (one vertical length in between two shutters) (60 mm X 74 mm) glazing bead (35 mm X 20mm ) will be mitered cut and fusion welded at all corners including drilling of holes for fixing hardware and drainage of water etc making arrangement for fixing of hardware EPDM gasket 1.2 + 0.2 mm thick galvanized steel frame (28 mm X 21.5 mm ) sash (31 mm X 27 mm ) T profile (27mm X 17 mm ) to be inserted in required profile frame will be fixed to the wall with 8 mm X 100 mm long fasteners including casement door handle 150 mm long (white power coated ) corner striker . secondary strikers cylinder ,door transmission gear made of mild steel with multi point locking system with strikrs . 3D hinges of zinc alloyed (white powder coated ) complete all as specified and directed.

S&F 4.8 mm thick sheet glass any colour ordinary quality and glazing with oil putty in square n.exc 0.5 sqm min each pane complete all as specified and directed.

S&F factory made steel tubular window with side hung shutters including box type hinges with steel handle and steel peg stay with glazing bars dovetailed or welded complete all as specified and directed as per HQCELZ Lucknow Drg No LZ/C-TD/130 sheet 1/4 to 4/4 .

S&F factory made steel tubular Steel window with side hung shutters including box type hinges with steel handle and steel peg stay without glazing bars dovetailed or welded complete all as as per HQCELZ Lucknow Drg No LZ/C-TD/130 sheet 1/4 to 4/4 complete all as specified and directed.

M&L factory made steel tubular Steel ventilators with top hung shutter including hinges, steel peg stay as per HQCELZ Lucknow Drg No LZ/C-TD/130 sheet 1/4 to 4/4 complete all as specified and directed.

S&F mild steel Framed work such as grills, grating etc. with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

M/L for preparation of new steel surfaces any description not other wise described over 10 Cm width or girth and applying two coat of Synthetic Enamel paint over and including a coat of red oxide primer complete all as specified and directed.

S&F for galvnanised mild steel wire galvanized 0.45mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and directed

S&F 3mm thick plain glass sheet and glazing with oil putty in squares n. exc 0.5sqm in each pane complete all as specified and directed.

S&F 3mm thick Sheet glass in repair ordinary quality and glazing with oil putty in square n. exc. 0.5 Sqm in each pane including hackingout complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed.

Demolition of cement concrete not exc 15 cm thickness below or above ground level of any description complete all as specified and directed.

M&L for 25 mm thick plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in floors, finished even and rough to receive floor topping complete all as specified and directed.

M&L for first quality glazed ceramic coloured tiles of size 300mm x 450mm x 7 to 8 mm thick on vertical surfaces; set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tile over and including 10 mm thick screed bed in cement mortar 1:4, as in dado/ skirting complete all as specified and directed. Note: Colour, design and pattern shall be approved by GE(I).

M&L for 10 mm thick first quality Vitrified ceremic tiles light shade (square/ rectangular) area of each tile not exceeding 0.36 Sqm in floors etc; laid jointing in neat cement slurry and pointed in white cement mixed with pigment to match with shade of tiles over and including 15 mm thick screed bed in CM (1:6) complete all as specified and directed. Note: Colour, design and pattern shall be approved by GE(I).

M&L for 10 mm thick first quality Vitrified ceremic tiles dark shade (square/ rectangular) area of each tile not exceeding 0.36 Sqm in floors etc; laid jointing in neat cement slurry and pointed in white cement mixed with pigment to match with shade of tiles over and including 15 mm thick screed bed in CM (1:6) complete all as specified and directed. Note: Colour, design and pattern shall be approved by GE(I).

All as per item No 47 but in skirting over and including 10 mm thick backing plaster in CM (1:4) complete all as specified and directed.

M&L for first quality 7 to 8 mm thick non skid ceramic coloured tiles (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors etc; laid jointing in neat cement slurry and pointed in white cement mixed with pigment to match with shade of tiles over and including 15 mm thick screed bed in CM (1:4) complete all as specified and directed. Note: Colour, design and pattern shall be approved by GE(I).

M&L for first quality 7 to 8 mm thick non skid ceramic coloured tiles (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm as in floors etc; laid jointing in neat cement slurry and pointed in white cement mixed with pigment to match with shade of tiles over and including 15 mm thick screed bed in CM (1:4) complete all as specified and directed. Note: Colour, design and pattern shall be approved by GE(I).

Demolition on stone slab or tiles any description and thickness as in floor laid bedded and pointed in cement mortar complete all as specified and directed.

M&L granite (of any type) work (table rubbed and polished) as in platforms/tops/vertical surfaces etc 16 to 18 mm thick and like in CM 1:4 including pointing with coloured cement mixed with pigment to match the shade of stone including cutting, rubbing and polishing surface and rounding off edges, to the entire over and including 15 mm thick screed/rendering in CM 1:4 complete all as specified and directed.

M&L 18-20 mm thick machine cut kota stone (full size not less than single piece )slab in flooring , staircase steps , landing etc laid over 15 mm thick screed bed of CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing , grinding and mirror polishing complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius in brick thick wall built in CM 1:6 complete all as specified and directed.

All as per item No 55 above here in before but except bricks.including cleaning of bricks complete all as specified and directed. Note : Old serviceable bricks obtained vide item no 54 above shall be reused.

Taking down cement plaster from brick wall including racking out joints, hacking for key & scrubbing down complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on fair faces of concrete or brick surface finished even and smooth without using extra cement mixed wiith water proofing compound 3% by weight of cement or as per manufacturer instruction complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:6 on fair faces of concrete or brick, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 5 mm thick cement plaster on ceiling in CM 1:3 finished even and smooth without using extra cement complete all as specified and directed.

Supply only water proofing compound (ISI marked) complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coat of oil bound distemper on surfaces of wall over and including a coat of primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coat of cement base paint over and including a coat of cement primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash as on ceiling surfaces complete all as specified and directed.

S&F in repairs mortice lock vertical type size 100mm 2 levers of brass complete all as specified and directed.

S&F in repairs double action floor spring hydraulically regulated made up of minimum 1.25mm thick aliminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S/F, in repair mirror cabinet PTMT size 350X445 mm complete all as specified and directed.

S&F in repair aluminium (diecast body) hydraulically regulated door closer designation NO- 3,universal type suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

S&F in repair 150 mm length floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

Taking down aluminium door shutter of any description and refixing with necessary adjustment to door spring/door closer, aluminium /rubber beading glass panes etc complete all as as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

S&F steel rolling shutters complete without ball bearings 1.00 mm thickness of lath including top cover, anchoring rod, hasp and staple, guide channel and one shop coat primer, erected in position as indicated complete including taking down of the same push pull or manual type complete all as specified and directed.

S&F Ball bearing for rolling shutters complete all as specified and directed.

S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

Taking down of rolling shutter of area exceedes 7 sqm but not exc 12 sqm if necessary on ground, overhauling and welding etc of rolling shutters completely ( push pull or manual type) including oiling, greasing wherever is require including in guide chanel also and erected in the same position after changing of defective part if any including two coat of synthetic enemal paint over and including a coat of red oxide primer on steel shutter complete all as specified and directed. (Note- Defective parts shall be measured and paid separately as supply only under item no 76 to 82 and fixing of parts shall deemed to be included in quoted rates in this item )

Supply only interlocking rails matching with existing for rolling shutters complete all as specified and directed.

Supply only Ball bearing for rolling shutters complete all as specified and directed.

Supply only Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

Supply only 1 mm thick hood cover of PGI steel sheet with necessary fixing arrangement for rolling shutters complete all as specified and directed.

Supply only lock rail including sliding locking arrangement for rolling shutters complete all as specified and directed.

Supply only spring for rolling shutters complete all as specified and directed.

Supply only MS guide rail 2 mm thick for rolling shutters complete all as specified and directed.

S&F mild steel Framed work as in doors or gates of angle or other section of GDE Fe410-0 or Fe 310-O with gusset plates, rails, braces, etc., drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

S&F Mild Steel holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position complete all as specified and directed.

S&F collapsible steel gate, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners brass handles etc erected in position and securing runners with holdfasts and brackets complete all as specified and directed.

S&F of 1.00 mm thick Mild steel, plain, black sheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws,clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

Cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 (using 20 mm raded stone aggregate) as required complete all as specified and directed.

M&L 75 mm thick Cement concrete type D 2, 1:4:8 (using 40 mm graded crushed stone aggregate) as in sub base complete all as specified and as directed.

M&L for non skid coloured heavy duty parking tiles of size 300x300x9-10 mm thick impact resistance over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for chequered cement concrete tiles 30cm x 30cm x 22mm thick, laid over and including 15 mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of tiles complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness , M-35 grade, set, jointed over and including 25 mm thick sand cushoning complete all as specified and directed.

M&L for fully retro-reflective sign board of Engineer grade retroreflective sheeting having entire surface finally bonded with retro-reflective sheeting of engineer grade having pressure sensitive adhesive , borders and messages (length, letters , numerical etc) in Hindi & English as indicated , cut out or screen printing , back ground in blue colour tape & matter in white colour having both side writing complete all as specified and directed. Note : Mild steel frame work & steel sheet shall be measured & paid separately.

S&F of mild steel plain sheet and framed work for making of sign posts with hollow square sections , angle etc nut & bolts etc and similar work in shape and pattern as required at site and similar work complete all as specified and directed.

S&F of 2.0 mm thick plain , aluminium sheeting in sign boards etc fixed with screws in the mild steel frame work complete all as specified and directed.

S&F aluminium anodized angle 23.5 x 26.4 x 1.4 mm for fixing of aluminium sheeting to mild steel frame work complete all as specified and directed.

Demolition of RCC (reinforced cement concrete) of any description in ground floors and pavings n exc 15 cm thickness (below or above ground level) including removing demolished material from site complete all as specified and directed.

M&L for Precast RCC 1:2:4 type B-1 (using 20 mm grade stone aggregate) as in cover slab for manholes and drain etc set in cement mortar (1:4) complete all as specified and directed.

M&L mild steel TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F in repair CP Bib taps fancy type cast copper alloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed (15mm bore dia of pipe) complete all as specified and directed.

S&F in repair 15mm bore dia Pillar taps fancy type cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair 15mm bore angle cock, fancy type chromium plated screwed down high pressure , with crutch or butterfly handle screwed both ends for iron pipe or for brass ferule and fixed complete all as specified and directed.

S&F in repair 15mm bore stop valve fancy type long shank (Concealed type) chromium plated screwed down high pressure , with crutch or butterfly handle screwed both ends for iron pipe or for brass ferule and fixed complete all as specified and directed.

S&F in repair hand shower (health faucet) chromium plated with 15 mm dia 1 mtr long flexible tube and wall hook complete all as specified and directed.

S&F in repair EWC seat cover white with all fixing arrangement suitable for cascade type EWC of any make & pattern complete all as specified and directed.

S&F in repairs brass, chromium plated toilet paper holder complete all as specified and directed.

S&F in repair 15mm dia bore Chromium plated sink cock swivel type complete all as specified and directed.

S&F single peice type stainless steel gratings suitable for 100 mm dia floor trap complete all as specified and as direcred.

All per item No 107 above but 75 mm dia floor trap complete all as specified and directed.

S&F in repairs 15 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe and fixed (min wt-142 gram) complete all as specified and directed.

S&F in repairs 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe and fixed (min wt-210 gram) complete all as specified and directed.

S&F in repair corner glass shelf 25 cm radius with CP bracket and railing of approved quality complete all as specified and directed.

S&F chromium plated three way tap for laboratory use 15mm dia bore complete all as specified and directed.

S&F in repairs PVC connection 15 mm dia 450 mm long with 2 Nos PVC check nuts with washer complete all as specified and directed.

S&F in repair chromium plated tubular towel rail 20mm dia D type 60cm longs between flanges complete all as specified and directed.

S&F in repair soap dish, brass, chromium plated,size 100X60mm, fixed to wall with rawl plugs and chromium plated screws complete all as specified and directed.

S&F in repair looking mirror of size 600 mm x 450 X 4 mm thick glass with 5 mm thick plain PVC sheet fixed at back side and 5mm thick prelaminated PVC sheet frame around the mirror including hanging arrangement complete all as specified and directed .

S&F in repairs PVC low level flushing cistern of capacity 10 litre with inlet 15 mm bore ball valve , float and handle including brackets including PVC connection 300 mm with flanges at both ends screwed down to 15 mm bore pipe and 32 mm bore PVC flush pipe of required length including taking down out of existing flushing cistern complete all as specifiied and directed.

S&F in repair vitreous china WHB white flat back size 550 x 400 mm including angle iron brackets, and chromium plated pilar tap 15 mm bore fancy type CP waste coupling 32 mm dia & PVC connection 450 mm complete all as specified and diected.

S&F in repairs vitreous China Orrissa pan with integral foot rest size 580 mm x 440 mm white with ‘P’ or ‘S’ trap front or back inlet and foot rests any pattern fixed including concrete bedding complete all as specified and directed.

Demolition of old existing unserviceable EWC seat and S&F vitreous china wash down water closet pan (Pedestal pattern),white including connection to drain (or outgoing pipe) and to flushing pipe,anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repairs 25 mm dia PVC laminated mild steel conduit as in curtain rod and fixed to brackets complete all as specified and directed.

S&F in repairs fancy type mild steel brackets and side knob suitable for 25 mm dia curtain rod and fixed to wall with screws complete all as specified and as directed.

S& F in repair Vitreous China Urinal, full stall type, white including flushing pipe ,waste coupling and waste pipe complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F 15 mm bore galvanized steel tubes medium grade with all fittings laid concealed/surface in walls complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F 20 mm bore galvanized steel tubes medium grade with all fittings laid in walls complete all as specified and directed.

Dismantling water tanks Capacity of tank exc 250 & n. exc 500 ltrs and removing from site complete all as specified and as directed.

S&F HDPE triple layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 500 litres capacity hoisted and fixed in position all as specified in SSR Pt-I including for hoisting into position either inside or outside of building, connecting up pipes, securing access cover etc including GI nipple of suitable size and 20mm dia PVC float valve assembly complete all as specified and directed.

Dismantling water tanks exc 500 ltr and n.exc 1000 ltr and removal from site complete all as specified and directed.

S&F HDPE triple layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 litres capacity (White colour) hoisted and fixed in position all as specified in SSR Pt-I including for hoisting into position either inside or outside of building, connecting up pipes, securing access cover etc including GI nipple of suitable size and 20mm dia PVC float valve assembly complete all as specified and directed.

M/S AADI ENTERPRISES (BID ID -3163923)

RAJAT TRADERS (BID ID -3160833)

ADITYA VIKRAM SINGH ASSOCIATES (BID ID -3160793)

RAJA RAM AND COMPANY (BID ID -3164079)