SPL REPAIR TO BLDG NO P-1 (A) OF STN HQ BUILDING , DELHI AREA AND P-56 OTM SINGLE LIVING ACCN AND BATH ROOM /TOILET AND BUILDING NO P-57(COOK HOUSE) AND ALLIED WORKS AT DELHI AREA PROVOST UNIT UNDER GE(EAST), DELHI CANTT-10

Amount

Demolition of Brickwork of stone/boulder masonry, build in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stone work and precast concrete articles

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition Reinforced cement concrete of roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed

Dismantling of cast iron or reinforced concrete or PVC drain pipes including all fittings and accessories, 100/75 mm dia and in any position all as specified.

Dismantling water tanks exc 500 Ltrs but not exc 1000 ltr capacity and removing to store.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 sqm each complete all as specified

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each complete.

Taking down shutters of any description exc 1 Sqm and not exc 2 Sqm and refixing or resecuring in same opening complete.

Supply and fixing Double leaf openable 10 mm thick toughened full frosted glass 24'6" sq feet door made with lock and self closing device with Hardware for openable door of SS 304 one set, Supply and fixing 8 to 10 mm thick toughened glass 49' sq feet for fixing glass portion fixed glass sheet complete all as directed by Engineer in charge. :- (a) L Connector SS 304-11 Nos. (b) Holes in Glass - 20 Nos.

S&F aluminum anodised powder coated grill section 5 to 6 mm of square/dimond shape having picth size of mesh 75x100 mm etc complete all as directed.

Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One )vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, Frame (30mm x 18mm) 2 nos, sliding sash (30mm x18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor includes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.)(A) Area not exceeding 2.00 sqm each .

S&F for Stainless steel wire mesh 0.36 mm dia fixed with tinned tacks of stainless steel wire and avg width of aparture 1.4mm complete.

M&L of E-board 4mmthick self design type tiles ceiling on GI Powder coated channel/Tee/Grid of make(Armstrong or equivalent) frame work with the following specification including cutting holes to brick wall built in cement mortar & making good in cm 1:3 of cement concrete 1:2:4 type BO as required including dismantling of existing ceiling board :-. (a) Plugging to wall around the rooms & supplying & fixing GI Powder coated angle of size 25x25x1.0 mm (b) S&F of 1.60 mm dia GI wire suspenders with adjustable clamps including fixing to ceiling dash free fasterers(c) S&F 25 x25 x1.5mm GI Powder coated tee as in main & cross members at 595mm c/c supported suspenders alongwith adjustable clamp to maintain level . ( d) S&F E-board 4mmthick self design type ceiling tiles of size 595mm x 595mm confirming to relevant IS in squares of GI Powder coated Tee with clips made to shape including taking down. Shade and pattern of E- oard shall be as approved by GE.

M&L for Vetrified ceramic tiles ultra charged (Light shade) 10mm thick (square/rectangular) area of each tile exc 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM (1:4) complete all as specified.

Ditto as item no 16 but 10mm thick CM 1:4 as in backing coat for dado/skirting complete all as specified.

M&L for Non skid ceramic coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM (1:4) complete all as specified.

M&L for 1st/Premium quality glazed ceramic digital coloured tiles with highlighter concept in matching pattern of size 600X 300X 7 to 8 mm thick as in vertical surfaces such as skirtings, dados etc set & jointed in neat cement slurry & pointed with white or coloured cement to match the shade of tiles incl 15 mm thick backing coat in CM (1:4) complete all as specified and directed.

M&L for 1st/Premium quality glazed ceramic digital coloured tiles with highlighter concept in matching pattern of size 1200X 600X 7 to 8 mm thick as in vertical surfaces such as skirtings, dados etc set & jointed in neat cement slurry & pointed with white or coloured cement to match the shade of tiles incl 15 mm thick backing coat in CM (1:4) complete all as specified and directed.

M&L brick work with sub class 'B' st or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brickwork with subclass `B' bricks, straight or curved on plan to any radius in half thick brick built in CM(1:4) complete all as specified and directed.

M&L for 50 mm thick in Plain cement concrete type C2 ( 1:3:6)( using 40 mm graded aggregate ) as in plinth protection laid in alternate bays (not exceeding 2 Sqm each) finished even and smooth at top without using extra cement and providing joints throughout the thickness of plinth protection, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight all as directed at site.

Taking down cement plaster / duster bed PCC of Column, chajja, Parapets of roof, facia, drops etc and making good with cement plaster 10mm thick in CM 1:3 with PCC 1:2:4, (average thickness of PCC 25mm) as required, brushing neat cement slurry with 3.0kg of cement per sq. metre including necessary form work and scaffolding upto 2nd floor including fixing of wire netting where required to match the existing surfaces.

Taking down cement plaster on brick wall including racking out joints hacking for key scrubing down with water etc

M&L for 15 mm thick cement plaster in cement mortar 1:6 on brick or concrete surface (internal) etc. on wall finished even and smooth without using extra cement, all as specified .

M&L for 10mm thick cement plaster on brick or concrete surfaces, as in ceiling / facia / chajja etc. in cement mortar 1:3 finished even and smooth without using extra cement, all as specified .

M&L for 15 mm thick external rendering on brick work or cement concrete surfaces in cement mortar 1:4, finished fair and even without using extra cement incl mixing of water proofing compound complete all as specified. (Note: Water Proofing compound shall be measured and paid for separately)

Supply only water proofing compound.

M&L for Preparation of new/old plastered surfaces of walls and two coats of exterior emulsion paint (Weather Coat) over a coat of priming paint etc complete all as specified and directed.

M&L Preparing new plastered surfaces of walls and applying two coats of OBD over a coat of primer over a layer of 1 mm thick JK Birla wall putty complete all as specified

M&L for two coats of OBD on ceiling surfaces complete all as specified and directed.

Preparation of new steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer, all as specified.

Wire brushing and cleaning top surface of tiles, cement concrete, including flashings and junction of parapets including taking down existing roof treatment with mud puska of any type and also taking down cement plaster on concrete surfaces, including raking out joints, hacking for key, scrubbing down with water etc., to receive further treatment, complete all as specified and as directed.

M&L for PCC 1:3:6 type C1 with 20 mm graded stone aggregate as in padding over roof slab for making slope on roof rop surface finished even and fair complete all as specified and directed.

M&L for 10 mm thick Cement plaster on surfaces of concrete in CM 1:4 on roof surfaces (Over PCC Padding) mixed with WPC complete all as specified and dierected. Note : WPC shall be measured and paid separately.

Material and labour for APP polymaric water proffing membrane minimum 3 mm thick and weighting not less than 3.50 kg /Sqm Make as per approved manufactured list black finished rienforced with non weven polystere matt with fusiable finish laid over compatable bitumen primer at the rate of 0.40Ltr/Sqm torching overlaps with a propane of abugane gas torch , with over lap 75 mm at the sides and 100 mm at the ends and sealing all as per manufacture's instructions including preparation of surface, complete all as specified and as directed. Note : The wate profing treatmen shall be carried out by the manufacture or their authorised applicators.

Taking up or down steel tubing 15 mm bore and connection including cleaning for refixing. complete all as specified and as directed by Engineer-in-Charge

Taking up or down steel tubing 20 mm bore and connection including cleaning for refixing. complete all as specified and as directed by Engineer-in-Charge

S&F steel tubes medium grade in any size or length galvanised with all fittings and fixed complete to walls and ceiling or laid in floor bore of pipe 15 mm dia, complete all as specified and as directed by Engineer-in-Charge

All same as per item No - 40 here-in-before but 20 mm dia complete all as specified and as directed by Engineer-in-Charge

S&F in repair for 15 mm dia fancy type CP bib taps half turn with wall flange with screwed down, screwed for iron pipe or for brass ferrule including cap and fixed complete all as specified and as directed by Engineer-in-Charge

S&F in repair 15 mm bore fancy type angle valves half turn chromium plated fancy type with wall flange screwed down high pressure screwed both ends for iron pipes or for unions complete all as specified and as directed by Engineer-in-Charge. Make : Jaquar continental series or equivalent in MARC/Kohler

S&F 15 mm bore brass CP single lever Basin mixture for Mixing Hot and Cold water fixed as per manufacture’s manual, with long shunk and cup washers, screwed both ends for iron pipes or for unions complete all as specified and directed Make : Jaquar Cat No ARICHR39001B or equivalent in MARC/Kohler

S&F Vitreous China (star white) WHB counter type of size 450 x 450 x 170mm including CP waste fittings complete all as specified.

S&F in repair sheet glass shelf assembly consisting of .mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified. Make : Jaquar Cat No WHT25905 or equivalent in Jaquar/MARC/Kohler

S & F in repairs Two way Angle valve 15mm bore dia or pipe, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed.

S & F CP Toilet Paper holder with flap guard complete all as specified and directed.

S&F CP towel ring complete all as specified & directed.

S&F CP Brass soap dish complete all as specified & directed.

S & F Corner Glass Shelf 300 x 300 mm radius consisting of 5.5mm thick sheet glass with chromium plated brass brackets with two No CP Railing in each set complete all as specified and directed Make Cera or equivalent Hindware.

S & F Corner Glass Shelf 225 x 225mm radius consisting of 5.5mm thick sheet glass with chromium plated brass brackets with two No CP Railing in each set complete all as specified and directed.

S & F CP Health Faucet with 1.00 Mtr long CP Flexible pipe as per approved sample complete all as specified and directed.

S&F in repairs vitreous china wash down extended Floor mounted water closet pan(Italian collection) white/colored cascade type (Integrated Model) including vitreous china flushing cistern, flush pipe, PVC seat cover with 'P' or 'S' trap complete all. Make : Hindware Cat No 192055 or equivalent in Jaquar/MARC/Kohler

S&F in repairs vitreous china wash down extended wall mounted water closet pan(Italian collection) white/colored cascade type (Integrated Model) including vitreous china flushing cistern, flush pipe, PVC seat cover with 'P' or 'S' trap complete all. Make : Jaquar Solo SLS/WHT/6851PL80PP or equivalent in Jaquar/MARC/Kohler

S&F CP towel rail 600mm long complete all as specified and as directed by Engineer-in-Charge

S&F 600mm long PVC connection with stainless steel armed 15 mm bore with nuts complete all as specified and as directed by Engineer-in-Charge

S&F of 1000 ltr.capacity rotational moulded polye-thylene water storage tanks three layered (cylindrical vertical with closed top)holsted & fixed in position incl tank nipple stop cock and float valve with iron rod and PVC ball all as specified inSSR Part-I complete all as specified and as directed by Engineer-in-Charge.

S & F in repairs 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F PVC (SWR) floor/Nahani trap, plain with grating including jointing with solvent cement, 75mm diameter of outlet, all as specified.

S&F PVC(SWR) pipes, 75 mm external dia double socketed in any length with rubber joints, fixed to walls with PVC brackets/clips complete all as specified.

S&F PVC (SWR) pipes, 110 mm external dia double socketed in any length with rubber joints, fixed to walls with PVC brackets/clips complete all as specified.

S&F PVC(SWR) bends suitable for 110 mm external dia complete all as specified

S&F PVC (SWR) junction single, (single T) equal or unequal of 75mm dia

S&F PVC (SWR) junction single, (single T) equal or unequal of 110mm dia

S&F PVC (SWR) junction double, (double T) equal or unequal of 75mm with access door

Supply and Fixing of factory made Moduler Kitchen , Cupboards, cabinets having size of 4.1 mtr (length) x .45 mtr (width) x 0.75 mtr (ht) with Carcases of the Kitchen unit made of 18 mm thick BSB HDHMR- Actuin Tesa or equivalent in make as per approved make list for side , devider, Top and Bottem and boths side balancing white with .8mm thick duly edge banded at all exposed edges of the unit back of the carcases made of 8 mm thick HDHMR boths sides Pre laminated duly 2mm thick face will be white and outside will be as approved shade all as per manufacturer instructions under the Kitchen and wire fititing Fittings.

S&F of 100mm Long polished brass Handle fancy type fixed with screw.

S&F of magnetic catches fixed complete

S&F of continues (piano) hinges, mild steel, bright finish width of flap (when open) 30mm.

S&F Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete

S & F Grinding and polishing of of existing kota/Marble stone floor as specifications and as required as per Enge inin Charge.

S & F Venition Blinds with Fabirc sides of length and width including Framing hooks and conneting ietms as per specified and directed by Engr in Charge.

M&L for External texture paint of approved pattern and colour of incl complete removal of existing treament and aplying putty for preparation of base for texture, appling one coat of primer and appling finish coat for texture of approved pattern and colour by Engr-in-charge complete

Aluminum alloy powder coated door including frame and channel of section (Door frame single groove 101.6mm x 44.45mm x 2.1mm, shutter top section 47.62mm x 44.45mm x 1.95mm thick, shutter bottom section 114.30mm x 44.45mm x 2.15mm thick, shutter vertical section 85mm x 44.45mm x 1.80mm thick, shutter middle section 83.50mm x 44.45mm x 2.40mm thick & glazing clips weighing not less than 0.097 Kg/RM) including shutter fixed to sliding type/openable frame and channel as directed and approved by GE and as per IS specifications including provn of 5.5mm thick tinted glass/12mm thick prelaminated particle board as required including handles, tower bolt, floor spring heavy duty, locking arrangement “GODREJ”, rubber gasket and door stopper complete.

Mild steel work as in Hollow section, angle Iron, flat Iron for fixed indepently connecting purlin, rafters, MS plate as reqd forming holes bolted and welded attchment and curved shaped by welding (thickness of metal n.exxc.6mm) making jointless by filling including cutting etc, complete all as specified and as directed.

S&F Pre-Painted min 60mm puff insulated having density not less than 40 kg/cum and thermal condictivity 0.02w/mk sandwich with galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick on both faces of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed.

M&L for false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of raw plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of MR board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering up to 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete including dismantling of existing work as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge MR resistant board. Note : The cost of board has been included in this item.

M&L for PROwood grooved panel having system NRC up to 0.88 with lineal perforation. The high grade MDF panels shall be melamine laminate of size 2440mm x128mm x 18mm with 2mm groove at 14mm pitch, Tongue and Groove edges for seamless mounting having density of 800kg/m3(base panel confirming to IS 12406 and laminated panel confirming to IS 14587). The back of the panels are perforated with a nonwoven fabric covering of 0.2mm for providing Sound absorption via the acoustic impedance method. Panel is fixed by using GI Framework 2400mmx50mmx0.50mm spaced at 600mmx600 c/c & 16 mm WPC framework spaced at 400mm centers with suitable brackets and the system is backline with 50 mm Rockwool insulation@48kg density and along with all accessories or Screw the aluminum extruded profile for channeled woodworks provided by manufacture over the lowest and second wooden batten at an on- center distance of 600mm. Install the first set of wooden panels by inserting the clips for border channeled woodworks and insert the groove of the panel into the projecting flange of the aluminum clip. Continue installing rows of panels by inserting the tongue into the groove of the earlier inserted panel and progressively installing clips for inside channeled woodworks into the next keel till the actual height is achieved. Use clips for border channeled woodworks to finish off the installation.

Excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sq. m on plan and not exc 1.5m in depth and getting out in soft/loose soil, complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil, complete all as specified.

Spreading and levelling in layers n exc. 25 cm thick, complete all as specified

Removing excavated soils n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

M & L for PCC 1:4:8 Type D2 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified.

M & L for cutting openings, through brick walls built in cement mortar for door, window and other openings or enlarging existing openings, converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc., to store and rubbish to a distance not exc. 50m complete all as specified.

M & L 18/20 mm thick granite (of any type) work( table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab including demolition of existing granite/stone slap of any type and size.

M&L for flat formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams , sides and soffits (if any) foundation and plinth beams and similar work vertical or to batter finshied surfaces of concrete complete all as specified.

M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work not exc 5cm wide, as roughed finished surface of concrete complete all as specified.

S&F framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe .290.Gde-E-165 complete all as specified.

M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to IS complete all as specified.

M & L for mild steel TMT bars of 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to IS commplete all as specified.

M & L for mild steel TMT bars 5mm dia and over upto including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to IS complete all as specified and as directed by the Engineer-in-Charge

S&F Joist, channel, angle, or tee sections, fixed independently , without connection plates, etc. ( cut to ordinary lengths i.e within 20mm of the length indicated) to Fe-290-(Gde E- 165) complete all as specified .

M&L 75mm thick cement concrete 1:3:6 type B2 using 40mm graded stone aggregate as in plinth/sub base. Complete all as specified.

M & L for hardcore of broken bricks n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and remmed to a true surface, complete all as specified

M&L for RCC footing, pillers, colimns , plingth beams, LINTEL BAND etc Reinforced cement concrete (nominal mix) in shelves supported on walls using cement concrete type B-1 1:2:4 (20mm crushed stone graded agg) complete.

M & L brick work with sub class B , straight or curved on plain or walls surface of any description and any position not otherwise specially provide built in CM( 1:4) complete.

M & L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150mm bore pipe line complete all as specified.

S&F Vitreous china half stall urinal (back or corner wall type) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 , securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement fixing flush Pipe, grating & union for discharge Pipe complete all as specified.

S&F VANITY MADE OF 18mm HDHMR BOARD of size 580x450x680 mm with mirror cabinet of size 500x700 mm with table top basin complete all as specified and directed make:- Amara in Parryware cat part of main cabinet C-896146, mirror cabinet C-896G46 and wash hand basin C896H1C all as approved by GE.

S&F Suspended Gypsum board ceiling works in decorative steps including vertical/sloping members includes with GI perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) alongwith perimeter of nailing screw fixed in brick wall/RCC with the help of nylon seelves and screws at 610mm centre, then suspending GI intermediate channels of size 45mm (0.9mm thick with two flange of 15mm each) from the soffits at 1220mm centre with GI cleat and steel expansion fasteners, ceiling section of 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 457mm centres, 12.5mm tapered edge gypsum board conforing to IS 2095 (1982) is then screw fixed to ceiling section with 25mm drywall screws at 230mm centre,. Screws fixing is done mechanically either with screw driver or drilling machine with suitable attachment finally the board are to be jointed and finishing the tapered and square edges of the boards are to be joints compound, joint fiber tape including dismatling of old false ceiling any description , including two coat of OBD over a coat of chalk whitening putty complete all as specified and directed. Cost of gypsum board is incuded in quoted rate. Note :- Details of fixing & material will be got approved by GE before commencement of work.

S &F Factory made solid panel pvc door shutter 30 mm thick (style) con-sisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be cov-ered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain col-our PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & draw-ing.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete as specified and directed

S&F WPC SHEET WALL PANELLING of thickness 5mm ( ±0.25 ) consisting of panels of desired size stuck on inner frame work of 50mm wide strips of 5mm (±0.25 ) thick Prelam WPC sheet. The panel & strips shall be Density of 650 Kg /Cum Manufactured by an ISO-9001-2015 certified Company. The strips should have in their center a grove of 6mm width and 1mm depth for sinking the head of the screw used to fix the strips to the wall vertically at an equal interval of 10” between two WPC strips. The WPC strips shall be fixed to the wall using 65mm long M.S. screws through the groove in the strip by using PVC fasteners. The distance between two screws shall not be more than 200mm. A groove of 2mm may be left at the joint of two panels for aesthetic looks. The exact size of the panel and correspondingly of the grid may vary depending on the size of the wall. Optionally a strips of 5mm (±0.25 ) thick WPC sheet of width 75mm feathered at the edges shall be stuck at the places where two panels are joined, using solvent cement. including clips,corner complete all as spcified.

S & F for Pressed steel frames size of 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, including filling hollow portions frame with PCC 1:3:6 type C0 using 12.50mm graded crushed stone aggregate, etc, complete all as specified and directed.

S&F 40mm thick factory made flush shutter, solid core construction with block board and plywood face panels, commercial type on both sides, complete all as specified and directed.

S&F 35mm thick second class hard wood Glazed and skelton shutters, open rebated and prepared to receive wiremesh, gauge, etc (without sashbars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing wiremess, etc, sizes of members of shutters as specified in SSR Part -, Section 8, clause 8.24 (a); supplied and fitted to chowkats.

S & F for steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified.

S & F for steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with out glazing bars, dovetailed or welded complete all as specified.

Aluminium alloy powder coated windows including aluminum powder coated frames sliding track, bottom weighing not less than 1.015 Kg/RM, sides and top not less than 0.826 Kg/RM double revated and 0.55Kg/RM for window shutter with one fixed glazed shutter and two nos glazed/gauged shutter sliding type with aluminium sections as per series - A (15mm) 3 track of Jindal section numbers for sliding windwos with framed shutter including aluminium allow powder coated snap type beads handles with locking arrangement spring action and glazing clip joint cleats rubber gaskets etc including provision of 5.5mm thick tinted glass/frosted glass of superior quality and stainless steel jali including all standard fittings, complete all as specified and as directed.

S & F Solid PVC door frame of size 50mm x 95mm made out of wood grain printed PVC sheet used reinforced with M.S. tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

S & F Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front and back Face (wooden finish pattern), supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed.

Powder coated aluminium partition with frame of standard powder coated aluminium sections of size 101.60mm x 44.45mm x 2mm in vertical and horizontal members and glazed with 5mm thick tinted glass and 12mm thick prelaminated particle board interior grade with laminations on both faces as directed by Engr-in-Charge according to site requirement including jointing cleats, glazing pins, rubber packing and fixing accessories as per site requirement, complete all as specified and as directed.

S & F 3mm thick Sheet glass, ordinary quality and glazing with oil putty in squares n exc 0.5sqm in each panes

M & L for cement concrete PCC 1:5:10 type E-2 (using 40 mm graded stone aggregate) as in filling under sunken floor etc complete all as specified and as directed.

M & L for rendering 15mm thick on concrete surfaces on walls in CM (1:3) mixed with WPC @3% by weight of cement in Sunken portion complete all as specified and as directed. (Note : WPC shall be measured and paid separately)

M & L for coloured vetrified tiles of size 600 x 600 x 8-10mm thick as in floor over 15mm thick screed bed 1:6 in cement mortar, set and jointed in white cement with pigment to match including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), complete all as specified and as directed.

M & L for Machine cut kota stone slab flooring 20-25mm thick over 15mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M & L Machine cut green marble stone 18 - 20mm thick prepolished in Floors over 15mm thick screed in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and as directed. Including demolition of existing green marble/stone slab of any type and size.

M & L Machine cut green marble stone 18 - 20mm thick prepolished in riser of steps, skirtings, dado and thick over 10mm thick rendering in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and as directed. Including demolition of existing green marble/stone slab of any type and size.

M & L for 75mm thick Cement concrete 1:4:8 Type D-2 (using 40mm graded agg) as in sub base of flooring or in any position including demolition of cement concrete (unreinforced) in ground floor or in any position and paving not exc. 15 cm thick (below or above ground level) complete all as specified and as directed.

M & L for Chequered cement concrete tiles 25cm x 25cm x 25mm thick, set, jointed and pointed in neat cement slurry over 15mm thick screed bed in CM 1:6, complete all as specified and as directed. Including demolition of existing chequered/stone slab of any type and size.

M & L for Coloured Machine pressed precast conctete interlocking paver block of any shape and size (Two colour combination) confirming to IS 15658-2006 of 60 mm thick, M-35 Grade with grey cement and pigment laid dry in floor/path , complete all as specified and as directed. Including demolition of existing interlocking tiles/stone slab of any type and size.

M & L for applying Smartcare Dampproof, a fibre reinforced elastomeric liquid water proofing membrane formulated with reinforcing acrylic fibers having Sun Reflectivity Index (SRI) of 105 on horizontal/vertical surfaces of roof/wall/chajjas in multiple coats @2.0 litre/sqm. Primary coat is self-priming coat of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1, damp proof : water) and other coats to be applied undiluted. The coating needs to be reinforced with 40 GSM geotextile, to sandwiched between 2nd & 3rd coat of coating. The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes complete in all respect as per the direction of Engineer-in-Charge. Make: SmartCare Damp Proof of Asian Paints or equivalent in Berger and Nerolac. Notes: (1) The work shall be executed through authorised applicator of manufacturer only. (2) Authrised Applicator shall be approved by GE before starting of work. (3) All materials shall be procured directly form manufacturer. (4) The contractor shall furnish a written guarantee for the effectiveness of the water proofing treatment for a period of Eight years in favour of the GE.

M & L for preparation of new plaster external wall and ceiling surfaces of and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) over and including priming coat of exterior primer applied and 1mm thick wall care putty over new surfaces complete all as specified and as directed.

M & L for preparation of plastered or unplastered old decorated surfaces of wall and ceiling including brooming down or scraping down with steel wire brushes of smoke spots , moulds ,moss efflocerent salts and treading oil and greasy spots, filling the cracks, holes with POP/Putty and applying One coat of weather schiled exterior acrylic emulsion paint (Appex Paint) of any tint all as per manufacturers instructions to achive desired finish at any height complete all as directed.

M & L for preparation of plastered or unplastered old decorated surfaces of wall and ceiling including brooming down or scraping down with steel wire brushes of smoke spots , moulds ,moss efflocerent salts and treading oil and greasy spots, filling the cracks, holes with POP/Putty and applying One coat of Oil bound distemper complete all as specified and directed.

Preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified.

Preparation of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided, complete all as specified and directed.

S & F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, Complete all as specified and directed

S & F in repairs Vitreous china squatting pan of each pattern long pan size 580mm white with 'p' or 's'trap fixing with screws of suitable size, complete all as specified, making connections to trap and to flush pipe, fixing flushing cistern etc, and making good to floors, complete all as specified.

S & F in repairs Vitreous china floor mounted WC ( Cascade) one piece type (off white) including connecetion in drain etc incl water closet seat cover CP jet spary, Health Faucet, flushing cistern, with P or S trap with all fitting and fixture complete all as specified and as directed. (Make : Jaquar or equivalent in Cera/Parryware).

S & F in reapir 10 Ltrs capacity PVC valveless symphonic action type flushing cistern white low level with inlet, ball valve float handle including bracket and flush pipe etc complete all as specified and directed

S&F Urinal spreader of CP any colour for fixing with 15mm dia pipe.

S & F Vitreous china wash basin counter oval type size 600x425x195mm, fixed in repairs, under granite slab with all fitting and fixture, fixed in repairs, complete all as specified and as directed.

S & F in repairs Sinks without drain board made of stainsless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortor on to dwarf walls or including cantilever brackets and connecting union to pipe overall size 495mmx420mm bowl size 410mmx330mmx160mm all as specified and directed.

S & F in repairs Sinks with drainage board made of stainsless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortor on to dwarf walls or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx 160mm all as specified and directed.

S& F Brass chromium plated towel rack of size 600 mm x 350mm, fixed with brass screws, fixed in repairs, complete all as specified and as directed.

S & F in repairs Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed.

S & F Stainless steel Grating dome 125mm dia with or without hole for waste pipe, fixed in repairs, complete all as specified and as directed.

S & F in repairs Brass CP basin mixer central hole, for mixing hot and cold water fixed as per manufacture's manual, with long shunk and cup washers, screwed both ends suitable for 15mm bore GI pipe joints to GI pipes or unions, complete all as specified and as directed. Make & Cat Part : Jaquar-Cat No. KUP-35051BPM, Jaquar-Cat No. KUP-35005BPM, Kohler-Cat No. K-74013IN-4BND-CP, Kohler-Cat No. K-74026IN-4BND-CP.

S & F in repairs Brass chromium plated wall mixture 3 in 1 system with provision for hand shower and overhead shower and suitable for 15mm bore GI pipe including three joints to steel pipes or unions and plugging and screwing to walls, fixed in repairs, complete all as specified and as directed. Make & Cat Part : Jaquar-Cat No. CON-281KN, Jaquar-Cat No. COP-281PM Kohler-Cat No. K-98754IN-4-CP.

Stainless steel Curtain Rod 20 mm dia with holders fixed to wall etc., fixed in repairs, complete all as specified and as directed.

Stainless steel fancy type bracket with new screws for curtain rod, fixed in repairs, complete all as specified and as directed.

PVC (SWR) 75mm bore bends with access door, complete all as specified and directed.

PVC (SWR) 110mm bore junction double, (double T), equal or unequal with access door, complete all as specified and directed.

PVC (SWR) vent cowl of size 110mm bore, complete all as specified.

S&F stack clamps out of 50mm by 5mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of 110mm bore of pipe, complete all as specified.

S&F stack clamps out of 50mm by 5mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of 75mm bore of pipe, complete all as specified.

M & L for PCC 1:2:4 type B-1 using 20mm graded stone agg as in surface channels complete.

Demolition and breaking up drain pipes (SGSW/ AC/RCC) including hunching and benching set in cement mortar for 150mm to 300mm dia pipe, and removal of debris from site and deposited where directed at a distance not exc 1KM from site complete all as specified and as directed.

M & L for 300 mm dia (internal dia) RCC hume pipe class NP -2 laid and and jointed complete with colleres complete laid in trenches and tested complete all as specified and as directed.

M& L for PCC 1:3:6 type C2 using 40 mm grade stone aggregate as in bed to drain pipe 300 mm bore incl forming cradles complte all as specified and directed.

S & F for Precast RCC manhole covers 75 mm thick medium duty conforming to IS-12592, complete all as specified and as directed.

Taking down old unserviceable point wiring from existing conduit / batten type (light, fan, socket or power point) complete such as switches, light fittings , ceiling rose, pendent holder, regulator and socket etc and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing complete all as directed.

Material and labour of point wiring complete with 1.5 Sq mm (nominal area) FRLS PVC insulated un-sheathed and multistranded copper conductor cable ISI marked in existing PVC concealed conduit and FRLS PVC insulated unsheathed 1.5 Sqmm copper conductor mulistranded earth wire, connecting to common earth dolly with and incl Metal flush box with modular sheet of suitable size for fixing modular switches/sockets etc for one light point / fans point controlled by one 1-way switch complete all as directed.

All as per srl item no. 161 here-in-before but with 1.5 sq mm FRLS copper wire with 1.5 Sqmm FRLS copper earth wire for one socket outet point 5 amps on the same board..

All as per srl item no. 161 here-in-before but with 1.5 sq mm FRLS copper wire with 1.5 Sqmm FRLS copper earth wire for one socket outet point 5 amps on the independent board..

All as per srl item no. 161 here-in-before but with 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for 15 Amp power point.

Material and labour of point wiring complete with 1.5 Sq mm (nominal area) FRLS PVC insulated un-sheathed and multistranded copper conductor cable ISI marked and including PVC concealed conduit ISI marked of size 20 mm min dia medium grade and PVC conduit fittings such as tees, bends, elbow, reducers including cutting & chasing and FRLS PVC insulated unsheathed 1.5 Sqmm copper conductor mulistranded earth wire, connecting to common earth dolly with and incl Metal flush box with modular sheet of suitable size for fixing modular switches/sockets etc for one light point / fans point controlled by one 1-way switch complete all as directed.

All as per srl item no. 165 here-in-before but with 1.5 sq mm FRLS copper wire with 1.5 Sqmm FRLS copper earth wire for one socket outet point 5 amps on the same board..

All as per srl item no. 165 here-in-before but with 1.5 sq mm FRLS copper wire with 1.5 Sqmm FRLS copper earth wire for one socket outet point 5 amps on the independent board..

All as per srl item no. 165 here-in-before but with 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for 15 Amp power point.

S & F Modular switch 6 Amp, 1 way, 1 module size complete all as directed.

S & F Modular switch 16 Amp, 1 way, 1 module size with indicator lamp complete all as directed.

S & F modular socket two-in-one, 6 Amp universal type, 02 module size complete all as directed.

S & F modular Socket, 16 Amp, multipurpose shutter type, 02 module size complete all as directed.

S & F Modular bell push 6 Amp, 1 way, 1 module size complete all as directed.

S & F Modular Fan regulator step type ,120 watts, 1 Module size complete all as directed.

S & F switch 5 Amp, 1 way, complete all as directed.

S & F socket two-in-one, 6 Amp universal type, complete all as directed.

S & F Socket, 15 Amp, multipurpose shutter type, complete all as directed.

S & F switch 15Amp, 1 way, complete all as directed.

Supply and fixing Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps complete all as directed.

Supply and fixing electric bell of DINGDONG type, 230 volts, single pole and making all necessary connections complete all as directed.

Material and labour submain wiring complete with 2 x 4.0 sqmm (nominal area) FRLS, PVC insulated, unsheathed and multistranded copper conductor cable ISI marked, and 1 x 4 sqmm as earth wire through existing PVC conduit of size 25 mm dia, medium grade and conduit fitting such as tees, bends, elbow, reducers etc complete all as directed.

Material and labour submain wiring complete with 2 x 4.0 sqmm (nominal area) FRLS, PVC insulated, unsheathed and multistranded copper conductor cable ISI marked, and 1 x 4 sqmm as earth wire in and including PVC conduit of size 25 mm dia, medium grade and conduit fitting such as tees, bends, elbow, reducers etc complete all as directed.

Material and labour submain wiring complete with 2 x 6.0 sqmm (nominal area) FRLS, PVC insulated, unsheathed and multistranded copper conductor cable ISI marked, and 1 x 6 sqmm as earth wire in and including PVC conduit of size 25 mm dia, medium grade and conduit fitting such as tees, bends, elbow, reducers etc complete all as directed.

Material and labour submain wiring complete with 2 x 10.0 sqmm (nominal area) FRLS, PVC insulated, unsheathed and multistranded copper conductor cable ISI marked, and 1 x 10sqmm as earth wire in and including PVC conduit of size 25 mm dia, medium grade and conduit fitting such as tees, bends, elbow, reducers etc complete all as directed.

M&L XLPE insulated armoured heavy duty electric cable with aluminium conductor ,1100 volt, size 16 sqmm 2 core complete all as specified and as directed.

Supply and fixing lamp holder PVC/ polycarbonate type suitable for batten fittings complete all as directed.

Supply and fixing of wall light fitting comet type with 9 w LED lamp complete all as directed.

S & F LED simple batten fittings 10Watts, cool/warm white complete all as specified and

S & F LED simple battens fittings, 1x20Watts, cool/warm white ,connecting up with three core flexible copper wire complete all as specified and directed..

Supply and fixing LED ceiling light fitting 12 watt, in round shape, recessed/surface type and making all electric connections complete all as directed.

S&F in replacement of Recess/Surface mounting 2x2 square flat panel ultra slim scoop LED light 36/40 W warm/cool white with driver/transformer etc suitable for Grid ceiling/Gypsum board/POP ceiling incl making electric connection complete as as directed.

M& L PVC cable ducts size of (wxh) 40x25mm complete all as directed.

M& L PVC cable ducts size of (wxh) 25x40mm complete all as directed.

S&F in replacement of LED bulk head fitting 10 watt made of cast aluminium alloy with opal glass diffuser complete all as specified and directed.

Supply & fixing stepped type electronic fan regulator flush type complete all as specified and directed.

Taking down of ventilating fan any type, size complete all as specified.

Supply and fixing of Ventilating fan 250 mm sweep plastic body type including self cosing louver and making all electric connections complete all as directed.

Taking down ceiling fan/Ex fan/wall fan, sealing cable end dismantling blades and removing fan and blades to deposited E/M store yard complete all as specified.

Supply and fixing ceiling fan complete with blades, down rods, suitable for regulator and accessories, 230 V, 1200mm sweep (BLDC) complete all as specified.

S&F of Exhaust fan 300mm sweep single phase( inbuilt gril), fixed in wall with proper nuts & bolts as reqd and incl connecting provn of PVC insulated and sheathed three core copper conductor flexible cable of size 23/0.0076mm to connect exhaust fan to ceiling rose all as directed.

S&F of Exhaust fan 450mm sweep single phase( inbuilt gril), fixed in wall with proper nuts & bolts as reqd and incl connecting provn of PVC insulated and sheathed three core copper conductor flexible cable of size 23/0.0076mm to connect exhaust fan to ceiling rose all as directed.

Supply and fixing in of Wall Mounted Fan 400 mm sweep plastic body type including making all electric connections complete all as directed.

Taking down of Geyser any type ,size & to deposited E/M store yard complete all as specified.

Supply and fixing of Geyser 25 ltr capacity vertical type with steel tank and glass inner linen , 5 star rating complete including fastners for hanging and CP and PVC connection for inlet and outlet upto stop cock including complete all as specifed and directed.

Supply and fixing of Modular AC Socket with 25 Amps SP mini MCB, 230 Volts, 50Hz. complete all as specified and as directed.

Supply and fixing of MCCB incommer Distribution Board ( Vertical Load line DB) double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, VTPN 04 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB as incommer and MCB as outgoing and making all necessary connections and taking out the old unserviceable DB complete all as directed.

S&F of MCB DB confirming to IP 43 - IK 09 with double door, SPN 08 way, double door complete with din rail, Neutral and Earthing bar after taking out the old unserviceable DBs, connection complete and making good the disturbed surfaces.

S&F of MCB DB confirming to IP 43 - IK 09 with double door, SPN 12 way, double door complete with din rail, Neutral and Earthing bar after taking out the old unserviceable DBs, connection complete and making good the disturbed surfaces.

Supply and fixing of MCB C Curve type, 10 kA, 10 to 32 Amp, Single Pole with over load.

S&F of SPN, isolator, 40 Amp, 240 Volt.

S&F of SPN, isolator, 63 Amp, 240Volt.

Supply and fixing in replacement of MCCB 3 pole ,415 V Adjustable type 160Amp with breaking capacity 16KA.

Supply and fixing in replacement of MCCB 4 pole ,415 V Adjustable type 100Amp with breaking capacity 16KA.

Supply and fixing in replacement of MCCB 4 pole ,415 V Adjustable type 125Amp with breaking capacity 16KA.

Supply and fixing in replacement of MCCB 3 pole ,415 V Adjustable type 200Amp with breaking capacity 36KA.

Supply and fixing in replacement of MCCB 3 pole ,415 V Adjustable type 250Amp with breaking capacity 36KA.

Earthing complete with galvanised steel earth plate electrode 600mmx600mmx6.3 mm thick burried in ground vertically to a depth not less than 2.25 meters below ground level with top edge of the earth plate at a depth not lesss than 1.5 meter below the ground level, earth plate surrounded 15 cm thick layers of common salt and charcoal dust starting from ground below 15 cm of earth plate and up to 15 cm above the same. GI plate connected with galvanised iron earth lead of size 4 mm by means of galvnised nuts, bolts and washers. GI wire of 4 mm dia laid in 15 mm dia light grade GI pipe as protection from top of the plate up to test point (cost of protection pipe up to 7.5 meters from earth electrode will be included in the rates quoted by the contractor).

S & F in replacement of energy efficicent LED fittings 45W LED 6K suitable for builing security light pressure die cast aluminium roadway luminaire with high power LEDs and HF electronic driver complete all as directed.

M&L GI 32mmTubes, 'light grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors

Supply and fixing in street light fitting bracket, 1.5 mtr long made out of galvanized iron pipe of 25mm dia size light grade complete with nut, bolts, washer etc inclusive of one primer coat, one under coat and one finishing coat of silver paint complete all as directed.

M&L for form work to soffits to suspended slabs such as roof slabs, floor, slabs landings and stair and similar work not exe. 20 cm thick flat rough to receive plaster all as specified and directed

S&F of 4 Pole isolator 100A complete all as specified and directed

S&F in replacement of TPN DB 04 way double door confirming to IP 43 & IK-09 protection complete with din rail, neutral & earthing bar after taking out the old U/S DB's connection complete all as specified and directed.

Gaurav Construction Company

Singh Associates

The new hut furnitures

Vipul Construction

imran construction company