8879/E8

Amount

Taking down carefully Window Type / Split Type / Tower Type Air Conditioner 1/1.50 / 2.00/3 Ton capacity, from its location and removing dirt and dust from interior and exterior of the Air Conditioner and washing the condensor and evaporator with varmi clean solution and other areas by soap solution, spraying pressurised water on condensor and evaportor with proper protection of electrical fixtures and connection, drying by blowing air, and placing in same position complete all as directed .

Taking down unserviceable Rotary/reciprocatory Compressor from Air Conditioner Window Type / Split type 2 Ton capacity of any make & type and Supply and Fixing reconditioned sealed compressor suitable for 2.0 TR window/split type Air conditioner including vacumminishing, initial charging of oil along with new foundation rubber pads, nut and bolts including testing on full load complete all as directed Note: Cost of charging of gas is not included in this item and will be paid under Appropriate item of schedule.

All as per serial item No. 2.00 mentioned here-in-before but for air conditioner of window Type / Split type 1/1.5 Ton capacity

Taking down unserviceable Rotary/reciprocatory Compressor from Air Conditioner Window Type / Split type 2.0 Ton capacity of any make & type and Supply and Fixing new sealed rotary type compressor suitable for 2.0TR window type/split type Air conditioner including vacumminishing, commissioning ,testing and initial charging of oil of air conditioner along with new foundation rubber pads, nut and bolts including testing on full load complete all as directed Note: Cost of charging of gas is not included in this item and will be paid under Appropriate item of schedule.

All as per serial item No. 04 mentioned here-in-before but for air conditioner of window Type / Split type 1/1.5 Ton capacity. Note: Cost of charging of gas is not included in this item and will be paid under Appropriate item of schedule.

All as per serial item No. 04 mentioned here-in-before but for inverter AC of window / Split type of capacity 2.0 ton. Note: Cost of charging of gas is not included in this item and will be paid under Appropriate item of schedule.

All as per serial item No. 04 mentioned here-in-before but for inverter AC of window / Split type of capacity 1/1.5 ton. Note: Cost of charging of gas is not included in this item and will be paid under Appropriate item of schedule.

Supply and fixing in repair compressor 2.5 TR per existing make 3 phase including vacumminishing, commissioning ,testing and initial charging of oil complete all as directed including taking down old unserviceable one complete. Note: Cost of charging of gas is not included in this item and will be paid under Appropriate item of schedule.

Supply & fixing of new strainer including testing including taking down old unserviceable one complete all as specified and directed .

S&F copper capillary tube with filter of appropriate quality and size to match in existing including jointing, brazing and testing suitable for window/split type AC's of 1/1.5/2.0 TR capacity including taking down old unserviceable one complete all as directed.

S&F capacitor of 2.5 to 10 MFD capacity, AC 240 volts and 50 Hz including taking down of old unserviceable capacitor complete all a specified and directed.

S&F capacitor of 25 to 60mfd capacity AC 240 volt and 50 Hz including taking down of old unserviceable capacitor complete all as specified and directed .

M & L for providing new wooden frame of size 50mmx50mm including removing old one and reinstalling existing AC and making electrical connection including all connected items complete all as specified and directedby

S&F in repair ply wood board of 6 mm thick cut into sizes as required at site for AC with and including support for fixing of ply wood and applying one coats of synthetic enamel paint over a coat of pink primer complete all as directed by Engineer-in-Charge.

Supply and Fixing in replacement old unservicable chassis body of window AC unit made out of MS sheet alongwith new cabinet cover as per same size suitable for 1.5/2.0 Ton AC duly spray painted with two coats of synthietic enamel paint (shade of colour as approved by Engineer-in- Charge) ,suitable for installing evaporator coil, condenser coil ,copper wounded fan motor, blower and fan blade and suitable front grill etc, remote sensing unit and wiring complete all as directed

S&F in repair Plastic Front Grill assembly alongwith PVC filter complete suitable for any make of window type 1.5 / 2.0 tone Air Conditioner complete all as directed by Engineer-in-charge.

S&F of Air filter for AC window/split type for 1/1.5/2 TR capacity including taking down old unserviceable one complete all as specified and directed.

S&F in repair Evaporator cooling coil and fins made out of copper tubing at appropriate spacing complete in all respects suitable for Window Type of capacity 1/1.5/2.0 Ton including brazing/welding etc. complete all as directed. Note: (i) Cost of charging of gas is not included in this item and will be paid under Appropriate item of schedule. (ii) Cost of new foundation rubber pads, nut and bolts including testing on full load complete is included in this item

S&F in repair Condensor cooling coil and fins made out of copper tubing at appropriate spacing complete in all respects suitable for Window Type of capacity 1/1.5/2.0 Ton including brazing/welding etc. complete all as directed Note: (i) Cost of charging of gas is not included in this item and will be paid under Appropriate item of schedule. (ii) Cost of new foundation rubber pads, nut and bolts including testing on full load complete is icluded in this item

S & F fan motor double spindle for window AC1/1.5/2 TR with appropriate gauge of super enameled copper conductor to match with the existing design including heat varnishing, overhauling, testing and re-fixing the same after taking down the old unserviceable one complete all as specified and directed.

S&F in repair Fan blower suitable for Window Type Air Conditioner as per existing of capacity 1TR/1.5 Ton / 2.0 Ton complete all as directed.

S&F in repair Fan Blade suitable for Window Type / Split Type Air Conditioner outdoor unit of capacity 1/1.5 Ton / 2.0 Ton complete all as directed.

S & F in repair base tray for window AC made of sheet metal complete all as specified and directed.

S&F of drain pipe with drain cap of window& split type AC 230 volt, single phase for (1/1.5/2.0 TR ) including taking down old unserviceable one complete all as specified and directed.

S&F in repair thermostat used for sensing and temperature control suitable for Window Type/ split type Air Conditioner 1/1.5 Ton / 2.0 Ton complete all as specified and directed

Taking out unserviceable Blower motor from the indoor unit split Type Air Conditioner of any make / type / capacity and supply and fixing new Blower motor of same make / type / capacity including nut and bolts if required complete all as directed by Engr-in-Charge.

Dismantling of unserviceable fan motor from the Air conditioner of 2.0/1.5/1.0 Tonne capacity and re-winding of fan motor with appropriate gauge of super enameled copper conductor to match with the existing design including heat varnishing, overhauling, testing and re-fixing the same complete all as specified and directed .

S & F fan motor of outdoor unit of Split AC of 1/1.5/2TR capacity with appropriate gauge of super enameled copper conductor to match with the existing design including heat varnishing, overhauling, testing and re-fixing the same after taking down the old unserviceable one complete all as specified and directed.

S&F in repair PCB including Remote Control for remote sensing and operation suitable for Window Type / Split Type Air Conditioner 1.5 Ton / 2.0 Ton make as approved by Engineer-in-charge.

M & L for reparing PCB board of AC 1/1.5/2.0 TR capacity of suitable for window/Split AC including taking down old unserviceable one complete all as specified and directed.

S & F in repair PCB board for inveter type AC 1.5/2.0 TR capacity of suitable for window/Split AC with remote including taking down old unserviceable one complete all as specified and directed.

S & F sensor of AC 1/1.5/2.0 TR capacity of suitable for window/Split AC including taking down old unserviceable one complete all as specified and directed.

Supply and filling refrigerant gas R-22 for AC complete including testing all as specified and directedby Engr-in-Charge.

Supply and filling refrigerant gas R-32 for AC complete including testing all as specified and directedby Engr-in-Charge.

S & F bush bearing of blower fan motor for window/split type AC, including taking down old unserviceable one complete all as specified and directed .

M&L for flushing out the condenser from gas system by creating vacuum, leakage testing of the system, injecting CTC solution for demoistureing the system and gas charging by R-22/R-134/R-32/R-410/R-600 upto the required pressure for 1.5 / 2.0 Ton Window Type / Split Type Air Conditioner complete all as specified and directed by Engineer-in-charge. Note :- (i)The cost of gas is included in this item and nothing extra shall be paid on this account. (ii) The cost of capillary/drier/flare nut if required is included in this item item and nothing will be paid extra on this account

S & F in repair inner unit bracket / wall stand of inner unit of split type AC of capacity 1/1.5/2 TR including taking down old unserviceable ones complete all as specified and directed.

S&F in repair Evaporator cooling coil and fins made out of copper tubing at appropriate spacing complete in all respects suitable for indoor unit of split Type of capacity 1.5/2.0 Ton including brazing/welding etc. complete all as directed. Note: (i) Cost of charging of gas is not included in this item and will be paid under Appropriate item of schedule. (ii) Cost of new foundation rubber pads, nut and bolts including testing on full load complete is included in this item

S & F in repair blower/runner of Inner unit including bush of AC of capacity 1/1.5/2 TR including taking down old unserviceable ones complete all as specified and directed. complete all as specified and directed.

M & L for PVC copper cable for min. 2.5 sqmm 3 core core for connecting the indoor and outdoor unit of split type ACs complete all as specifed and directed.

M & L for PVC copper cable for min. 2.5 sqmm 4 core for connecting the indoor and outdoor unit of split type ACs complete all as specifed and directed.

S&F in replacement of blower fan by taking down of the outer unit of split AC of capacity 1/1.5 TR testing complete all as specified and directed by Engr-in-charge .

S&F in repair Condensor cooling coil and fins made out of copper tubing at appropriate spacing complete in all respects suitable for split Type of capacity 1.5/2.0 Ton including brazing/welding etc. complete all as directed Note: (i) Cost of charging of gas is not included in this item and will be paid under Appropriate item of schedule. (ii) Cost of new foundation rubber pads, nut and bolts including testing on full load complete is icluded in this item

S & F in repairs flare nut with dead cap suitable for window/split AC of any capacity complete all as specified and directed by Engr-in-charge .

S & F in replacement of valves of size 1/2", 1/4", 3/5",5/8" suitable for window/split AC of any capacity complete all as specified and directed by Engr-in-charge .

S&F in repair Copper pipe with insulation 1/2" dia, superior quality suitable for refrigeration of split ACs, drawn through/fixed to walls or roof complete all as specified and directed by Engr-in-charge .

S&F in repair Copper pipe with insulation 3/8"" dia, superior quality suitable for refrigeration of split ACs, drawn through/fixed to walls or roof complete all as specified and directed by Engr-in-charge .

S&F in repair Copper pipe with insulation 5/8"" dia, superior quality suitable for refrigeration of split ACs, drawn through/fixed to walls or roof complete all as specified and directed by Engr-in-charge .

S&F in repair Copper pipe with insulation 1/4" dia, superior quality suitable for refrigeration of split ACs, drawn through/fixed to walls or roof complete all as specified and directed by Engr-in-charge .

Supply of remote control unit of window/split AC as per original make of AC or compatibility of ACs complete all as specified and directed by Engr-in-charge .

Supply of universal remote control unit of window/split AC complete all as specified and directed by Engr-in-charge .

S &F MS Bracket heavy duty for outdoor unit of AC including taking down old unserviceable one and necesarry PCC work complete all as specified and directed.

S&F of contactor assembly for 2.0 /1.5/1TR split type AC single phase 230 volt condensing unit of any make including taking down old unserviceable one complete all as specified and directedby Engr-in-Charge.

Taking out unserviceable unit and Supply and install window AC unit complete of capacity 1.5 TR with 3 star rating and connection complete including drain pipe complete all as directed.

Taking out unserviceable indoor unit and supply and install indoor unit of split AC unit complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality of capacity 1.5 TR with 3 star rating , connecting pipe with complete insulation and coooneting with outdoor unit complete all as specified and directed.

Taking out unserviceable outdoor unit and supply and install outdoor unit of split AC unit complete of capacity 1.5 TR with 3 star rating and connecting pipe with complete insulation. .

Taking out unserviceable refrigerator and supply and install refrigerator min 240L min 2 star single door complete all as specified and directed.

Taking out of existing unserviceable compressor sealed unit from refrigerator of 165/190L and Repairing of compressor servicing, flashing refixing the after leakage testing, vaccummision the system gas charging complete all as specified and directed by Engr-in-Charge. Note: Refrigerant shall be measured and paid separately

Taking out of unserviceable compressor sealed unit from refrigerator of capacity 286/300/320 ltrs or deepfreezer 400L and Repairing of compressor servicing, flashing refixing the repaired compressor after leakage testing, vaccummision the system gas charging complete all as specified and directed. Note: Cost of charging of gas is not included in this item and will be paid under Appropriate item of schedule.

S&F of new compressor of capacity 286/320 ltrs for refrigerator or deepfreezer 400L after testing complete all as specified and directed including taking down old unserviceable one complete. Note: Cost of charging of gas is not included in this item and will be paid under Appropriate item of schedule.

S&F of new compressor of capacity 165/190 ltrs for refrigerator after testing complete all as specified and directed including taking down old unserviceable one complete. Note: Cost of charging of gas is not included in this item and will be paid under Appropriate item of schedule.

S&F of new compressor of capacity inverter refrigerator upto 320L after testing complete all as specified and directed including taking down old unserviceable one complete. Note: Cost of charging of gas is not included in this item and will be paid under Appropriate item of schedule.

S&F in repair Starting Relay Assembly with Over Load Protector any model complete all as directed.

Taking out of unserviceable thermostat switch & supply and fixing of thermostat for refrigerator of 165 to 310 Lts capacity complete all as specified and directed by Engr-in-Charge.

Taking out of unserviceable lamp holder including lamp case and S & F of new pigmy lamp holder and lamp case to match with the existing, suitable for refrigerators of any capacity complete all as specified and directed by Engr-in-Charge.

M & L for Refrigerant - (R-134A) complete all as specified and directed by Engr-in-Charge.

Taking out of old unserviceable strainer of refrigerators of any capacity including supplying and fixing of new strainer of approved quality to match with the existing complete all as specified and directed by Engr-in-Charge.

Taking out of old unserviceable door lock of refrigerator of any capacity & S/F of new door lock to match with the existing size complete all as specified and directed.

Taking out unserviceable cooling coil and Supply and Fixing cooling coil with condenser assembly for refrigerator of any capacity as per existing samples complete all as specified and directed.

S&F Adjustable shelves for refrigerator of any capacity as per existing samples complete all as specified and directed by Engr-in-Charge.

S&F Bottle retainer/shelves for refrigerator of any capacity as per existing samples including taking down old unserviceable one complete all as specified and directed.

S&F door handle for refrigerator of any capacity as per existing samples including taking down old unserviceable one complete all as specified and directed.

S&F freezer door as per sample including taking down old unserviceable one complete all as specified and directed.

S&F chill tray of any type/ capacity/ make as per sample including taking down old unserviceable one complete all as specified and directed.

S&F vegetable tray of any type/ capacity/ make as per sample including taking down old unserviceable one complete all as specified and directed.

S&F ICE tray of any type/ capacity/ make as per sample including taking down old unserviceable one complete all as specified and directed.

S&F Capillary tube size with filter to any type of refrigerators complete all as specified and directed by Engr-in-Charge. .

S & F heater of refrigerator of capacity upto 320 liter complete all as specified and directed by Engr-in-charge .

S & F magnetic gasket of refrigerator door of any capacity complete all as specified and directed by Engr-in-charge .

S & F timer for defrost of refrigerator of any capacitycomplete all as specified and directed by Engr-in-charge .

S & F condenser coil of refrigerator of capacity upto 320 liter complete all as specified and directed by Engr-in-charge .

Dismantling of worn out outer body of refrigerator and repairing by replacement to worn out portion of the body by welding/fabricating with approved quality and MS Sheet/PVC sheet to match with the existing shape including, refixing of all the dismantled enclosures of the refrigerator in position including testing, painting and commissioning complete all as specified and directed .

Taking out Water cooler upto 150L capacity from the existing place for repairing of compressor, servicing, and refixing the repaired compressor, leakage testing, vaccummision the system gas charging completely complete all as specified and directed. Note: Refrigerant measured separately.

S&F Bush of fan motor for water cooler of capacity upto 150L including taking down old unserviceable one complete all as specified and directed.

Taking out unserviceable relay from water cooler of capacity upto 150L Ltrs capacity and S&F of new relay to match with the existing complete all as specified and directed.

Taking out of unserviceable thermostat switch & S/F of new thermostat switch to the water cooler of any capacity complete all as specified and directed.

S & F copper capillary tube for water coolers of any capacity including taking out of old unserviceable tubes complete all as specified and directed.

Dismantling of worn out outer body of water cooler and repairing by replacement to worn out portion of the sheet metal body by welding/fabricating with approved quality and MS Sheet to match with the existing shape including, refixing of all the dismantled enclosures of the water cooler in position including testing, painting and commissioning complete all as specified and directed.

Taking out of existing worn out and perished rubber gasket of water cooler tank cover and S & F of new gasket as per existing sample for any capacity of water cooler complete all as specified and directed.

Taking out of existing worn out and unserviceable water faucets of any type 15 mm bore and S & F of cast copper alloy chromium plated push type / lift tap water faucets of 15mm bore complete all as specified and directed.

Taking out of existing worn out and unserviceable float valve 15mm bore of any type and S & F of ball valve of 15mm dia including inlet nipple and connecting unions etc complete all as specified and directed.

Taking out of worn out drain pipe including drain tray and repair the same and drain pipes to match with the existing for any capacity of water coolers complete all as specified and directed.

Taking out of old unserviceable top cover lock of water cooler of any capacity and S&F of new top cover lock to match with the existing complete all as specified and directed.

Servicing and maintenance of Dehumidifier including electrical panel, ducts, filter properly complete all as specified and directed. Note: Spares as required will be measured and paid separately.

Supply and fix Display card . 12 v.FLI / FLP / FLC (J) parts complete all as specified and directed

Supply and fix Filter. 340x370x50 mm complete all as specified and directed

Supply and fix Filter.610x610x50 mm complete all as specified and directed

Supply and fix Hinge. Zinc Die Cast . CD - 38X34 complete all as specified and directed

Supply and fix Latch. T -Type Comp. CD- 33MM complete all as specified and directed

Supply and fix Sensor RTD 4X150mm 3.5m LPT 100 complete all as specified and directed

Supply and fix Thermostat Panel Mount (Non-UL) complete all as specified and directed

Supply and fix Sprkt Driver 12T 1/2" P 12mm complete all as specified and directed

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 130 V to 295 V with output voltage stabilized at 230 V with accuracy of ± 2.5% LED Display wall mounted and of capacity 5 KVA complete all as specified and directed by Engr-in-charge . Note- Old US Voltage stablizer to be deposited to MES store.

Taking down point wiring (light, fan, socket and power complete including fixtures and fittings such as switches ceiling roses, pendents , regulators, sockets, light fittings etc and making good distrubed surfaces of wall floor etc as per existing finish. Complete all as specified and directed.

M&L for point wiring with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sq mm FRLH/S in and including concealed PVC conduit 20 mm dia medium duty ISI marked with all necessary fittings with sunken cast iron /pressed steel terminal box ,flush to surface and 3 mm thick laminated sheet top cover for mounting switches including 1.5 sq mm FRLH/S PVC insulated unsheathed stranded copper conductor as earth lead and connected to common earth doly for one light / ceiling fan/exhaust fan/bell controlled by one switch complete including cutting, chasing the surface and then making good the same in CM 1:3 complete all as specified and directed by Engr- in-charge.

All as per item No.105.00 mentioned here-in-before but 3 pin 5 amps socket out let point same board with other switches of cables of 1.5 sqmm

All as per item No.105.00 mentioned here-in-before but for one 5 amp switch socket combination on independent board with cables of 1.5 sqmm size

All as per item No.105.00 mentioned here-in-before but using 2.5 sq mm size stranded copper conductor cable for one 16 amp switch socket outlet on independent board including 2.5 sq mm FRLH/S PVC insulated unsheathed stranded copper conductor as earth lead and connected to common earth doly complete all as specified and directed by engineer incharge.

M&L for point wiring with PVC insulated unsheated stranded copper conductor cable FRLH/S of size 1.5 sq mm in and including PVC casing caping of required width with all necessary fittings with sunk cast iron /pressed steel terminal box and 3 mm thick laminated sheet top cover for mounting switches including 1.5 sq mm FRLH/S PVC insulated unsheathed stranded copper conductor as earth lead and connected to common earth doly for one light / ceiling fan/exhaust fan controlled by one switch complete all as specified and directed by Engineer incharge.

All as per item No.109.00 mentioned here-in-before but 3 pin 5 amps socket out let point same board with other switches of cables of 1.5 sqmm

All as per item No.109.00 mentioned here-in-before but for one 5 amp switch socket combination on independent board with cables of 1.5 sqmm size

All as per item No.109.00 mentioned here-in-before but using 2.5 sq mm size stranded copper conductor cable for one 16 amp switch socket outlet on independent board including 2.5 sq mm FRLH/S PVC insulated unsheathed stranded copper conductor as earth lead complete all as specified and directed by Engineer-in-Charge.

All as per item No.109.00 mentioned here-in-before but using 4 sq mm size stranded copper conductor cable for one 16 amp switch socket outlet on independent board including 4 sq mm FRLH/S PVC insulated unsheathed stranded copper conductor as earth lead or for AC Starter complete all as specified and directed by Engineer-in-Charge.

S&F lamp holder insulated body with back plate for batten fittings complete all as directed.

S&F in repair lamp holder insulated body with back plate for batten fittings complete all as directed.

S & F switch piano flush type 5/6 Amps 230V AC one way complete all as specified and directed by Engineer-in-Charge.

S & F in repair switch piano flush type 5/6 Amps 230V AC one way complete all as specified and directed by Engineer-in-Charge.

S&F socket outlet 3 pin 5/6 Amps 230 volts flush type. complete all as specified and directed by Engineer-in-Charge.

S&F in repair socket outlet 3 pin 5/6 Amps 230 volts flush type complete all as specified and directed by Engineer-in-Charge.

S&F bell push flush type 5 Amps 230V complete all as specified and directed by Engineer-in-Charge.

S&F call bell, ding dong AC 230 volt single pole (ding dong type) complete all as specified and directed by Engineer-in-Charge.

S&F in repair call bell, ding dong AC 230 volt single pole (ding dong type) complete all as specified and directed by Engineer-in-Charge.

S&F ceiling rose surface bakelite 65x50mm single phase 3 terminal complete all as specified and directed by Engineer-in-Charge.

S&F in repair ceiling rose surface bakelite 65x50mm single phase 3 terminal complete all as specified and directed by Engineer-in-Charge.

S&F switch socket combination 2in 1 5 pin 6 Amps 230 volts flush type complete all as specified and directed by Engineer-in-Charge.

S&F in repair switch socket combination 2in 1 5 pin 6 Amps 230 volts flush type complete all as specified and directed by Engineer-in-Charge.

S&F switch socket combination multipurpose 5 pin 10 and 20 Amps one switch complete all as specified and directed by Engineer-in-Charge.

S&F in repair switch socket combination multipurpose 3 pin 15Amps one switch complete all as specified and directed by Engineer-in-Charge.

S&F ceiling fan regulator electronic Step type, solid state, 240 volts, complete all as specified and as directed

S&F in repair ceiling fan regulator electronic Step type, solid state, 240 volts, complete all as specified and as directed

S&F in repair ceiling fan regulator electronic socket type, 240 volts, complete all as specified and as directed

S & F in repair switch piano modular flush type 5/6 Amps 230V AC way complete all as specified and directed by Engineer-in-Charge.

S&F in repair modular socket outlet 3 pin 5/6 Amps 230 volts 2 module flush type complete all as specified and directed by Engineer-in-Charge.

S & F in repair switch piano modular flush type 16 Amps 230V AC complete one way 1 module complete all as specified and directed by Engineer-in-Charge.

S&F in repair modular bell push flush type 5 Amps 1 module complete all as specified and directed by Engineer-in-Charge.

S&F in repair modular switch socket outlet multipurpose 3 pin 6/16 Amps 2 module complete all as specified and directed by Engineer-in-Charge.

S& F in repair modular electronic step type fan regulator by step type 230 volt 2 module complete all as specified and directed by Engineer-in-Charge.

S&F in repair switch socket combination with box multipurpose 3 pin 10 and 20 Amps one switch complete all as specified and directed by Engineer-in-Charge.

S&F in repair switch socket combination with box 2in 1 3 pin 6 Amps 230 volts flush type complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with two core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with two core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.

S & F LED bulb 9Watts 240V 50Hz 6500K b22 base in bulb holder complete all as specified and directed by Engineer-in-Charge.

Supply and fix Decorative wall light fixture made up of Polycarbonate, 9 W retrofit LED Lamp B22 base complete with all the connection with driver three core flexible copper conductor cases of suitable size complete all as specified and directed by Engineer-in-Charge.

S&F building security light pressure die cast housing with individual LEDs with modular secondary optics security light luminaires 35 watt LED with not less than 32mm dia light grade GI pipe bent to shape of 45'' 1.5 mtr long and nuts bolts including fixing arrangement after taking down old unserviceable one complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED luminaire 2ftx2ft 35/36 watt, 220 V AC recessed type / surface type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roofceiling including connecting up with driver three core flexible copper conductor cases of suitable size including taking town of old unserviceable one complete all as specified and directed by Engineer-in-Charge.

Supply and fix plug top 3 pin16A 240V Easy to carry, Non flammable & Durable Heavy duty , nickel plated brass terminals Long lasting polycarbonate plastic material complete all as specified and directed by Engineer-in-Charge.

S&F in replacement plug and socket in sheet metal enclosures with two pin and earth plug and socket complete with and including MCB SP 20 Amps 240 volts heavy duty all as specified and as directed by Engr-in-charge.

S&F A C starter unit consisting of one 25 Amp capacity starter, one 240 V 25 Amps 10 KA SPN MCB, one 25 Amps socket and one 25 Amps plug top prewire including 6 Module modular box alongwith cover plate and frame complete all as specified and directed by Engineer-in-Charge.

S&F sunken flush metal GI boxes for fixing of modular switches/sockets flush to the walls complete for 2 modules including taking down of old unsv one complete all as specified and directed by Engineer-in-Charge. Note: The cost of cutting chasing of wall, if required and making good disturbed surface in CM (1:3) and finishig the surface to match with existing surface, etc complete all as specified and directed by Engineer-in-charge including taking down old unserviceable blocks is included in this item and nothing will be paid extra on this account.

All as per item No. 149.00 mentioned here-in-before but for 3 modules

All as per item No. 149.00 mentioned here-in-before but for 4 modules

All as per item No. 149.00 mentioned here-in-before but for 6 modules

All as per item No. 149.00 mentioned here-in-before but for 8 modules

All as per item No. 149.00 mentioned here-in-before but for 12 modules

S&F modular cover plate with frame for fixing of modular switches/sockets complete for 2 modules complete all as specified and directed by Engineer-in-Charge.

All as per item No. 155.00 mentioned here-in-before but for 3 modules

All as per item No. 155.00 mentioned here-in-before but for 4 modules

All as per item No. 155.00 mentioned here-in-before but for 6 modules

All as per item No. 155.00 mentioned here-in-before but for 8 modules

All as per item No. 155.00 mentioned here-in-before but for 12 modules

S&F sheet metal enclosure distribution board TPN, 4 way, double door, powder coated, protection class IP-42, suitable for mounting MCB, DBs confirming to IS-13032, IS-8632, BS-5484 with min 200 Amp rating copper bus bar, complete all as specified & directed. Note:(i) Cost of thimbles for connecting cable to MCCBs/MCB and making good disturbed surface is included in this item and nothing will be paid extra on this account.(ii) Cost of dismantling DB and MCBs and refixing the functional MCBs is also included in this item and nothing will be paid extra on this account.

S&F sheet metal enclosure distribution board SP&N, 4 way, double door, powder coated, protection class IP-42, suitable for mounting MCB, DBs confirming to IS-13032, IS-8632, BS-5484 with min 200 Amp rating copper bus bar, complete all as specified & directed. Note:(i) Cost of thimbles for connecting cable to MCCBs/MCB and making good disturbed surface is included in this item and nothing will be paid extra on this account.(ii) Cost of dismantling DB and MCBs and refixing the functional MCBs is also included in this item and nothing will be paid extra on this account.

S&F sheet metal enclosure distribution board SP&N, 12 way, double door, powder coated, protection class IP-42, suitable for mounting MCB, DBs confirming to IS-13032, IS-8632, BS-5484 with min 200 Amp rating copper bus bar, complete all as specified & directed. Note:(i) Cost of thimbles for connecting cable to MCCBs/MCB and making good disturbed surface is included in this item and nothing will be paid extra on this account.(ii) Cost of dismantling DB and MCBs and refixing the functional MCBs is also included in this item and nothing will be paid extra on this account.

S&F TPN 63-100 Amps, 415 Volts FP with rapturing capacity 10KA C curve complete all as specified & directed.

S&F MCB 6 to 32 amps, C Curve with rapturing capacity 10KA single pole 415 Volts complete all as specified & directed.

S&F MCB DP 40 to 63 amps 240 volts 10KA C Curve breaking capacity complete all as specified & directed.

S&F in epair MCB 6 to 32 amps, C Curve with rapturing capacity 10KA single pole 415 Volts including taking down of old unserviceable one complete all as specified & directed.

S&F in replacement MCB DP 40 to 63 amps C Curve 240 volts 10KA breaking capacity including taking down of old unserviceable one complete all as specified & directed.

Supply and fix in repair only 1.5 Sqmm FRLSH Copper conductor coil in existing concealed conduit complete all as specified and directed.

Supply and fix in repairs only repairs 2.5 Sqmm FRLSH Copper conductor in existing concealed conduit all as specified and directed.

Supply and fix in repair electronic meters temper proof LCD display with polycarbonate cover 230 V, 10- 60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time, current reading, load, PF, voltage and KWH complete all as specified & directed. Note:- Old unserviceable meter shall be deposited to MES yard.

Supply and fix in repair only casing caping with accessories like tee, bend,elbow of high quality material size 12-20mm of 2m length complete all as specified and directed.

Supply and fix in repair only PVC flexible 2 core cable 1.5sqmm with copper conductor complete all as specified and directed.

Supply and fix in replacement of MS louvers iron with shutters suitable for existing exhaust fan of any size and shape at site upto bldg of G+10 storey complete all as specified and directed by Engg-in-charge

S&F in repair Sub main wiring with two single core cable PVC insulated unsheathed of copper multi stranded conductor FRLS cable of size 4 sqmm, 1100 votls grade drawing through and including conduit 20 mm dia medium duty including acessories such as Tee, bend, Elbow etc, ISI marked with and including PVC insulated 4 sqmm unsheathed multistranded FRLS copper conductor cable for earth continuity and connected to common earth dolly including cutting cashing of wall, if required and making good to disturbed surface in CM (1:3) and finish the surface to metal with the existing surface etc complete all as specified and directed by Engineer-in-charge including taking down old unserviceable submain wiring complete all as specified & directed. Note:- (i)Two lengths of 4 Sqmm cable, one length of 4 Sqmm cable and one length of PVC conduit will be measured as one length. (ii) Cost of taking down existing submain wiring including all accessories is included in this item and nothing will be paid extra on this account

S&F in repair Sub main wiring with two single core cable PVC insulated unsheathed of copper multi stranded conductor FRLS cable of size 6 sqmm, 1100 votls grade drawing through and including concealed conduit 25 mm dia medium duty including acessories such as Tee, bend, Elbow etc, ISI marked with and including PVC insulated 6 sqmm unsheathed multistranded FRLS copper conductor cable for earth continuity and connected to common earth dolly including cutting chasing of wall, if required and making good disturbed surface in CM (1:3) and finishig the surface to match with existing surface, etc complete all as specified and directed by Engineer-in-charge including taking down old unserviceable submain wiring complete all as specified & directed. Note:- (i)Two lengths of 6 Sqmm cable, one length of 6 Sqmm cable and one length of PVC conduit will be measured as one length. (ii) Cost of taking down existing submain wiring including all accessories is included in this item and nothing will be paid extra on this account

Taking down unserviceable ceiling fans and supplying and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete with all the connection as directed.

Taking down unserviceable wall fans and supply and fixing wall fans 400mm sweep power input 60Watts min speed 1350RPM min air delivery 85 CMM 240V 50Hz complete with electrical connection including making good to disturbed wall surface as per existing finish complete all as specified and directed including taking down old unserviceable one complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm including making good to disturbed wall surface as per existing finish complete all as specified and directed including taking down old unserviceable one complete all as specified and directed. Note:- Old unserviceable fan shall be deposited to MES yard.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm including including making good to disturbed wall surface as per existing finish complete all as specified and directed including taking down old unserviceable one complete all as specified and directed. Note:- Old unserviceable fan shall be deposited to MES yard.

Supply and fix exhaust fan made of steel complete blade fan motor with louvers at any height , voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm including making good to disturbed wall surface as per existing finish complete all as specified and directed including taking down old unserviceable one complete all as specified and directed. Note:- Old unserviceable fan shall be deposited to MES yard.

Dis-assembling carefully ceiling fans/wall fan (any make) of 1200/1400mm sweep, cutting & removing old copper winding wire and rewinding the same with new super enameled copper wire of suitable size / gauge including providing insulation by varnishing, oiling and greasing, replacing bearing and gun metal shaft required and reassembling back including testing complete. Note :- (i) Cost of bearings, rubber real, nut, bolt etc shall be measured in this item and nothing will be paid extra on this account. (ii) Working space if required, will be provided to the contractor for carrying out necessary rewinding/repair with in AGE E/M store yard premises (iii) If winded fan found unserviceable within six month of rewinding,contractor will repair the same without any extra cost. (iv)Cost of Machining work in body of ceiling fan by taking out worn out bearing, boring hole to accommodate ball bearings is included in this item and nothing shall be paid extra on this account. (v) Cost of carrying ceiling fan from site to the workshop and refixing of the same after repair is included in this item and all T&P and vehicle cost will be born by the contractor in this regard (vi) Spare parts except mentioned above shall be measured & paid separately.

Dis-assembling of exhaust fan of size 250mm/ 300mm/400mm AC 230 Volts, 50 Hz 900/1400 RPM for repair, removing existing burnt winding wire, bearing/bushes, flexible wire, shaft, check nuts, frame and rewinding with super enameled copper windings wire of suitable size and replacement of bushes, bearings, shafts, check nuts, bolts and washers, greasing, varnishing and reassembling back including testing complete. Note :- (i) Cost of bushes/bearings, provided shall be measured and paid in this item and nothing extra shall be paid on this account. (ii) Working space if required,will be provided to the contractor for carrying out necessary rewinding/repair with in AGE E/M store yard premises. (iii) If winded exhaust fan found unserviceable within six month of rewinding,contractor will repair the same without any extra cost. (iv)Cost of Machining work in body of exhaust fan by taking out worn out bush, boring hole to accommodate ball bearings is included in this item and nothing shall be paid extra on this account. (v) Cost of carrying exhaust fan from site to the workshop and refixing of the same after repair is included in this item and all T&P and vehicle cost will be born by the contractor in this regard. (vi) Spare parts except mentioned above shall be measured & paid separately.

Preparation of old painted surfaces of the body, blades, down rod etc of ceiling fans of size 1200/1400mm sweep (any make) complete by rubbing with amery paper and filing in cavities with approved filler and applying one coat of spray painting with synthetic enamel paint (Glossy white/ pale cream) on the body, blades, down rods complete all as specified & directed.

Preparation of old painted surfaces of the body and blades, of exhaust fans of size upto 400mm sweep (any make) complete by rubbing with amery paper and filing in cavities with approved filler and applying one coat of spray painting with synthetic enamel paint (Glossy white/ pale cream) on the body, blades, down rods complete all as specified & directed.

Supply and fix in replacement only capacitor 2.5 mfd to 3.15 mfd dry type for Ceiling fan make of capacitor complete all as specified & directed.

Supply and fix in replacement only capacitor 4 mfd to 6 mfd dry type for exhaust fan make of capacitor complete all as specified & directed.

Supply and fix in replacement only rubber bush complete with spring, nut bolt, fork hook and spilt pin, washer suitable for existing ceiling fan 1200mm/1400mm sweep complete all as specified and directed.

Supply and fix in replacement only Ceiling fan stator 48 inch sweep 12 mm copper winding including ,thick steel bolt with double nuts and locking pins and high quality rubber bushing to reduce vibration complete all as specified and directed.

Supply and fix in replacement only rotor complete suitable for 48 inch sweep ceiling fan all as specified and directed.

Supply and fix in replacement only ceiling fan mild steel body set (upper & lower) with two set of bearings for ceiling fans of sweep 1200mm duly painted and any make and fixing in position complete all as specified and directed.

Supply and fix in replacement only PVC canopy set (upper & lower) for ceiling fans with of size 1200mm to 1400 mm sweep and any make and fixing in position complete.

Supply and fix in replacement only aluminium blades with fan blade screws of ceiling fan for any sweep( 1200mm to 1400 mm) & make complete.

Supply and fix in replacement only MS heavy duty down rod of 15mm dia and 600mm length with necessary cutting / drilling holes and PVC connector specified and directed.

Supply and fix in replacement only PVC flexible 2 core cable with copper con-ductor of size 23/0.76 mm from ceiling rose to ceiling fan complete all as specified and directed.

Taking down carefully unserviceable geyser of any type and make from site after disconnections of water & electrical connections & carrying out to MES store yard for inspection and thereafter to workshop for repair & replacement of components such as heating element, thermostate, cable, neon lamp, plugtop, outer casing, plates & repair work to apparatus plate, copper tank,split plate including de-scaling of water tank etc and carrying back to MES store yard for testing and refixing at site and making water & electrical connection on completion and all as directed. NOTE: Spares shall be measured and paid separately.

M&L for brazing/gas welding of inner container copper of 25 ltrs /50 ltrs capacity and any make and making leak proof the geysers complete all as directed.

Supply only heating element 2KW as per existing make of geyser complete complete all as specified and directed by Engr-in-charge.

Supply only Thermostate for suitable existing geyser of 25/50 litrs capacity complete all as specified and directed by Engr-in-charge.

Supply only stainless steel connection pipe of length not less than 60cm including washers for incoming & outgoing hot & cold water connections as specified and directed by Engr-in-charge

Supply only Apparatus plate assembly complete for geyser of capacity 25/50 litrs capacity complete all as specified and directed by Engr-in-charge.

Supply only Outer casing made out of 22 SWG MS sheet suitable for geyser of capacity 25 litrs complete all as specified and directed by Engr-in-charge.

Supply only Storage tank fabricated from MS sheet gauge suitable for geyser of capacity 25 ltrs of make as specified and approved complete all as specified and directed by Engr-in-charge.

Supply only Split plate bottom cover made suitable for 25 litrs capacity geyser complete all as specified and directed by Engr-in-charge.

Supply only top cover complete all as specified and directed by Engr-in-charge.

Supply only insulating material glass wool complete all as specified and directed by Engr-in-charge.

Supply only Element holding brass stud complete all as specified and directed by Engr-in-charge.

Supply only MS clamp with anchor fastener bolt complete all as specified and directed by Engr-in-charge.

Supply only Fusible metal plug complete all as specified and directed by Engr-in-charge.

Supply only Neon lamp round/square with connection lead complete all as specified and directed by Engr-in-charge.

Supply only Non return valve for geyser inlet complete all as specified and directed by Engr-in-charge.

M&L for taking down BLDC ceiling fan from site and transporting to workshop for repair / rewiring and refixing the same after repair complete all as specified and directed

Supply only BLDC PCBA (controller Bd)

Supply only BLDC Ceiling Fan Stator Ferrite Magnet Ring 12/14/16 Poles

Supply only BLDC rotor magnetic coil of 12/14/16 poles

Supply only plastic 12 pole stamping ring

S & F suspended LED batten 4 feets with 1x40W indoor decorative luminaries with and including electronic driver and 1x40W LED lamp including wire suspenders ceiling coupler and taking down old unserviceable fittings complete all as specified & directed.

ELECTRO COMMERCIAL CO (BID ID -3510991)

ELECTRO FREEZE (BID ID -3512236)

INDIA ELECTRICAL EQUIPMENTS (BID ID -3511675)

KWALITY CONSTRUCTION (BID ID -3509068)

EASTERN REFRIGERATION AND ELECTRICAL CO (BID ID -3510383)

SUDHA ENTERPRISES (BID ID -3512059)

M/S J S ENTERPRISES (BID ID -3509568)