C/o MuKhya Mantri Lok Bhawan at Bhoranj Tehsil Bhoranj Dev. Block Bhoranj Distt. Hamirpur H.P.

Amount

Excavation in soil in Hilly Area including cutting and trimming of side slopes in all classifications of soil as per Technical Specification Clause 1603.1and then disposing of all surplus excavated earth as per direction ofEngineer in charge within all leads, lifts of materials and other incidentals.

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal within all leads and lifts, dressing of sides and bottom and backfilling in trenches with excavated suitable materials.

Excavation in foundations, trenches etc., in earth work,in all kinds of soil , stacking the eacavated soil not more than 3 metres clear from the edge of the excavation and then returning the stacked soil in 15cm. layers, when required in to plinths sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in and as per direction ofEngineer in charge within all leads, lifts of materials and other incidentals.

Foundation, footings basis of columns etc. and mass concrete.

Beams, cantilever, girders and lintels Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels not exceeding 1 Mtr. in depth in all heights from floor.

Columns, pillars, posts and struts Square, rectangular or polygonal in plan

Flat surfaces such as soffits of suspended floors, roofs, landings and the like floors etc.upto 200mm. In thickness.

Providing and laying cement concrete 1:6:12(one cement : six sand : twelve graded/crushed stone aggregate 40mm (Forty milimetres) nominal size) mechanically mixed and curing complete, excluding cost of form work in foundation and plinth, and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and Laying concrete for plain/reinforced concrete in open foundations complete as per drawing and technical specification clauses 802, 803, 1202 and 1203 .(1:5:10 without plum) as per direction ofEngineer in charge within all leads, lifts of materials and other incidentals.

Providing and laying cement concrete 1:4:8 (one cement : four sand : eight graded/crushed stone aggregate 40 mm (Forty milimetres) nominal size) mechanically mixed and curing complete, excluding cost of form work in foundation and plinth, and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and laying cement concrete work 1:1.5:3 (1 Cement:1.5: Sand: 3 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Foundations,footings bases of columns and the like and mass concrete.

Beams Cantilever girders and lintels, in all heights.

Columns, pillars posts and struts upto floor two level.

Suspended Floor roofs, landing and shelves and their support balconies,beams,girders,bressumers and contilever upto floor twolevel

Stair cases(Except spiral stair cases )excluding landing but including preparing of the surface and finishing of nosing upto all floor level.

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 and as per direction ofEngineer in charge within all leads, lifts of materials and other incidentals.

Providing weapholes in brick masonry / stone masonry /plain reinforced concrete abutment, wing wall, return wall with 100 mm dia PVC pipe extending through the full with of the structures with slop of 1(v):20(H) towards drawing face complete as per drawing and technical specification clauses 614, 709, 1204.3.7 and as per direction ofEngineer in charge within all leads, lifts of materials and other incidentals.

Providing mild steel/Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Brick work using common burnt clay building bricks in superstructure in Cement Mortar 1:6 (1 Cement : 6 Sand) Second Class Bricks and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Half brick masonry in common burnt clay building bricks in superstructure in Cement Mortar 1:4 (1 cement: 4 sand) Second Class Bricks and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Random rubble masonry/polygonal rubble masonry (uncoursed/ brought to coureses ) with hard stones of approved quility in foundation and plinth icluding leveling up with cement concrete 1:6:12 (1 cement:: 6sand: 12 graded stone aggregate 20 mm nominal size) at plinth level in cement mortar 1:6 (1 cement :6 sand) within all leads and lifts of matirials and other incidentals as per approved drawing and design and as directed by the Engineer -in-charge.

Providing second class deodar wood work in frames of doors, windows, clerestory, windows and other frames wrought,framed and fixed in position and as per direction ofEngineer in charge within all leads, lifts of materials and other incidentals.

P/F 12 mm thick prelaminated board both side bwp phenol bonded exterior / interior grade panalled shutters with frame of first class deodar wood for doors including bright finished/black enamelled iron butt hinges with necessary screws 40 mm thick frame and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and fixing panelled glazxed or panelled glazed shutters for doors, windows and clerestory windows including balck enaelled iron but lhinges with necessary screws 35mm thick (second class deodarWood) and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing 40x3 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm dia metres bolts, nuts and wooden plug and embedding in cement concrete block 30x10x15cm. 1:3:6 (1cement:3sand:6 graded stone aggregates. 20 mm nominal size) as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and fixing aluminium tower bolts (berrel type) anodized transparent or dyed to required shade and colour with screws etc. complete and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals. (125 mm)

Providing and fixing wire gauge shutters using galavanised M.S. wire gauge of I.S. gauge designation 85-G with wire of dia 0.56mm for doors windows and clerestory windows including bright finished black enamelled iron hinges with necessary screws 40mm thick second class deodar wood and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Supplying and fixing 4mm thick plain glass panes with putty and nails including removal of broken glass panes wherever necessary and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

25 mm thick Kota stone slab flooring 20 mm (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and polishing complete and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 10 mm. thick anti skid proof stain and impect resistent heavy duty vetrified tiels Nitco or equivalant 600 x 600 x10 mm manufacturaed of approved shade and colour in flooring, treads of steps and landings laid over 12 mm thick cement mortar 1:3 (1 cement :3 sand) jointed with cement slurry mixed with pigment to much the shade of tiles as required complete and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Kota stone slab 25 mm thick in risers of steps,skirting dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

White glazed tiles 6 mm thick in skirting risers of steps and dado 12 mm thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and laying marble work (Table rubbed and polished) in flooring 20 mm. thick base in cement mortar 1:3 (1cement:3sand) including jointing with cement mortar 1:2 (1 white cement:2 marble dust) with an admixure of pigment to match the shade of the marble. 20 mm thick White makrana marble and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge within all leads, lifts of materials and other incidentals.

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint In beams joists channels ,angles , tee, flats with connecting plates or angle cleats as in main and cross beams, hip and jack rafters,purlins connected to common rafters and the like and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg /sqm including filling the joints with approved adhesive complete 100mm dia pipes within all leads and lifts of matirials and other incidentals and as directed by the Engineer -in-charge.

Providing and fixing cast iron holder bats clamps of approved design to C.I pipe embeded in and including cement concrete blocks, 10cm10cmx10cm(Ten into ten into ten centimetre)of 1:2:4(One Cement two sand four graded stone aggregate, 20mm nominal size)including cost of cutting holder and making good the walls for 100mm ( One hundred millimeter) dia pipes within all leads and lifts of matirials and other incidentals and as directed by the Engineer -in-charge.

Providing and fixing on wall faces PVC (D-Plast) .accessories for rain water pipes including filling the joints with approved adehsive complete within all leads and lifts of matirials and other incidentals and as directed by the Engineer -in-charge.

P.V.C plain bend 100mm (One hundred milimetres) dia pipes.

P.V.C plain shoes 100mm (One hundred milimetres) dia pipes.

Providing and fixing M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Applying priming coat over new steel & other metal surfaces after & including preparing the surfaceby thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete With ready mixed priming paint brushing red lead, Red-oxide/zinc and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Painting two costs (excluding priming cost on new steel and other metal surfaces eith enamel paint brushin to give an even shade including cleaning the surface of all dirt, dust and other foregin matters Enamel paint other than white and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting readymixed paint brushing wood primer pink and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Painting two coats(excluding coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping with enamel paint other than white and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

6 mm th.plaster to ceiling in Cement mortar1:3 (one cement: three sand) and finished even and smooth and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

15 mm thick Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto all floor level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortor 1:6 (one cement: six sand) and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortor 1:6 (one cement: six sand) and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer

Applying one coat of Acrylic primer (Spectrum or equivalent of Superior quality) on new concrete/ masonry/ plastred surfaces after and including preparing the surface by thoroughly brushing the surface free from mortar droppings and other foreign matters, sand papering the surface smooth complete.

Applying one coat of AcrylicWashable emulsion Spectrum quartz king or equivalent finish for interior painting with brushes plain smooth finish composed of acrylic polymere in emulsion inorganic/special pigment siliceous aggregate anti fungicides anti-rusting & foaming in two coat i/c necessary putty to give smooth even surface, sand papered smooth complete and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing under layer of plinth protection 75mm (Seventy five milimetres) thick (Un-consolidating) bed of dry brick stone aggregate 40mm (Forty milimetres) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing plinth protection 50 mm (Fifty milimetres) thick cement concrete 1:3:6 (One cement: three sand : six graded)crushed stone aggregate 20mm (Twenty milimetres) nominal size including finishing the top surfaces of concrete smooth, within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer- Incharge.

Providing and fixing Orissa Pattern vitreous China wash down, water closet squatting pan (Indian type W.C pan) size 580 mm (Earth work, bed concrete, foot rest and trap to be measured and paid for separately) as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing Anglo Indian Universal closet vitreous China wash down, water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) (Seat and over to be measured and paid for separately) as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers white plastic seat and cover as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing vitreous China squatting plate pattern urinal of size 450 mm x 350 mm with integral longitudinal flush pipe as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing PTMT coloured/white high density polyethylene / poly propylene 10 litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately)and other incidentals, as per approved drawing, design and as directed by the Engineer-in charge.

Providing and fixing 5 litre net capacity PTMT Coloured / white automatic flushing cistern with a pair of PVC / C.I. or M.S. bracket complete with fittings including PVC syphonic apparatus, mosquito proof lid, PVC union and coupling for connections with inlet, outlet and over flow pipes including cutting holes and making good the same ( over flow pipe to be measured and paid for separately) as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting flat back 550 x 400 mm as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 32mm dia C.P. Brass waste for wash basin or sink as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 600mm x 450 mm bevelled edge mirror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 600mm x 20mmm C.P. Brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screwsas per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 600mm x 120 mm glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing Division Plate for Urinals 600mm x 300. Vitreous China as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 15mm dia C.P. brass bib tap with capstan head. as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 15mm dia C.P. brass Pillar tap with capstan head as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 15 mm dia C.P. stop cocks as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 300/450mm length 15 mm dia P.V.C connection with brass unions as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 32 mm dia PVC waste pipe for wash basin or sink as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

1000 ( one thousand litres net capacity tank )

500 ( five hundred litres net capacity tank )

Providing and fixing 110 mm X 90 mm PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 110 mm dia high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 90 mm dia high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 110 mm dia PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 90 mm dia PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 110 mm dia PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 90 mm dia PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 110 mm dia PVC collars ISI marked including fixing with approved adhesive etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 90 mm dia PVC collars ISI marked including fixing with approved adhesive etc. complete., as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 100 mm dia PVC ‘P’ or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 610 x 510 mm with bowl depth 200 mm stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 15 mm nominal bore to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floor, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and laying 15 mm nominal bore in trenches, galvanised mild steel tubes (medium grade), tube fittings (earth work in trenches to be measured and paid separately), as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 100mm nominal size diameter M.S. stay and clamps for sand cast iron / cast (spun) iron pipes, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing PVC cowl fixing with approved adhwssive complete 100 mm (One hundred millimetres) nominal size within all leads, lifts of materials and other incidentals.

Providing and fixing . brass valve (Horizontal plunger) . 15mm nominal bore within all leads, lifts of materials and other incidentals.

KAMAL PATHANIA GOVT.CONTRACTOR