Upgradation and modernization of Superintendent Office block at GMCH

Amount

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) (A) 112mm thick brick wall (a) In cement mortar in proportion 1:4. (1 cement:4 sand)

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side a) In cement mortar 1:3

Demolishing mosaic floor of various thickness, both mosiac tiles and cast-in-situ type including CC base course and removal of debris as directed for all levels.

Dismantling all types of ceiling, partition and wall lining and stacking the materials as directed by the department for all levels

Demolishing brickwork including stacking of serviceable materials and disposal of unserviceable materials as directed for all levels

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) (I) Using Mixer Machine (A) In substructure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. N) Without using admixture, plasticiser b) M20 grade concrete or Prop. 1:1.5:3

(B) In super structure from plinth level up to 1st floor level. ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. N) Without using admixture, plasticiser c) M25 grade concrete

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. (b) Using 25mm thick plank

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reinforcement bar

Providing and fixing plain frosted glass of ordinary glazing quality beded in putty and fixed with/without wooden bidding including necessary cutting and glass to be required sized(payment for woodenbead shall be made separately) (2). Area of glass panes exceeding 0.15m2 but not exceeding 0.52m2. (c). 5.00mm thick.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (a) In prop 1cement: 3 sand :6 coarse aggregate by volume

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) Digital- Gold ii) Of size 600mmx600mm and above

Providing,fitting and fixing wooden flooring from Uniproducts (India) Ltd.of thickness 14mm made of pure wood(Engineered Wood) of different types with a top layer of 3mm thick hard wood and Under layer of 2mm thickness made of polythene and foamsheet laid on existing concrete floor complete as directed and specified Engineered Wood (New) from Uniproducts(India) Ltd. i) Walnut Brand

Providing polished vitrified wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/white cement slurry mixed with approved pigment to match shade of tilesc complete at all levels as specified and directed. (coloured pigment should be in conformity with colour of tiles and as approved and directed by the department). iii) Of size 300mmx600mm and above

Providing polished granite slab of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile Choksey/Sika/Pedelite/Rouf) /white cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). (iii) Deluxe Quality (ii) With White cement

Extra for Granite finish in marble slab / tiles at all levels.

Providing wood work in frame (chowkaths) of doors, windows, clerestory windows and other similar works wrought, framed and fixed in position in contact with C.C or brick masonry wall including supplying, fitting and fixing with M.S. hold fast (40mmx3mmx250mm) as per design embeded in cement concrete block in proportion 1:2:4 and with two coats of kiricide oiling to the timber faces in contact with C.C and masonry as directed and specified. (a) With sal wood

Supplying and installing uPVC- Sliding Windows made out of Lead free green profile having "GREENLINE" mark of BIS standard uPVC multichambered sections of wall thickness 2.4mm with corners fusion welded, fully reinforced with Galvanized steel 1.5/2mm including interlock profile, glazing bead, grooving bead, brush seal, aluminum sliding track, stainless steel rollers, sealing wedge block, Espag, int handle, pop up handle, keeper, drain cap, fisher screws, packing pieces with all necessary stainlessness screws etc. complete as directed. The windows must be installed complete with all kinds of ironmongery including EPDM gaskets, bridging wedges and glass packers and with suitable water draining system. Application of silicon sealant from inside / outside of Dowcorning / GE or equivalent. With 5mm clear glass (a) 2 Track Sliding Window with Flyscreen using uPVC section of sizes 88mm x 50 mm x 2.4mm thick wall for frame with inbuilt flyscreen track, 37mm x 61mm x 2.4mm thick wall for glass sash, 25mm x 49mm x 2.4mm thick wall for flyscreen sash having 1.5mm thick reinforcement, Interlock: 43mm x 23mm (Glass Panel) (WINSTA KOMMERLING/ FINESTA/ ENCRAFT)

Supplying and installing uPVC- Casement Door made out of Lead free green profile having "GREENLINE" mark of BIS standard uPVC sections of wall thickness 2.4mm, multichambered with corners fusion welded, fully reinforced with Galvanized steel 1.5/2mm including glazing bead, folding gasket, glazing gasket, locking arrangement, Espag handle, Espag, keeper, drain cap, run up block, fisher screws, packing pieces with all stainless steel screws complete as directed. The windows must be installed complete with all kinds of ironmongery including EPDM gaskets, bridging wedges and glass packers and with suitable water draining system. Fittings ROTO / GQ or Equivalent. Application of Silicon sealant from Inside / Outside of Dowcorning / GE or equivalent. (b) Double leaf Side hung Door with a Dummy Mullion - French Door using uPVC section of size 58mm x 69mm x 2.4mm thick wall for frame, 58mm x 109mm x 2.4mm thick wall for glass sash, 58mm x 61mm x 2.4mm thick wall for dummy mulion, Aluminium threshold at bottom. (WINSTA KOMMERLING/ FINESTA/ ENCRAFT) i) Using 5mm clear glass

Applying primary coat over new steel and other metal surface over 100m in width or girth after preparing the surface by throughly cleaning oil,grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper. a). With ready mixed "red-lead/ red oxide" primer.

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. (i).Surfaces over 100mm in width or girth. b). High gloss (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) suspended ceiling which includes G.I. perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending G.I. intermediate channels of size 45mm (0.9mm thick with two equal flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angle of width 25mmx10mmx0.55mm thick fixed to soffit with G.I.cleat and steel expansion fasteners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two equal flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 298mm c/c. Then 12.5mm thick square edge Fulltone/ Sundance/ Cratone/ Louvertone/ Textured. Gypboard panels of size 595mmx595mm (conforming to IS:2095-1982) is then screw fixed to ceiling section with 25mm long drywall screws at 290mm c/c. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally, the boards are to be jointed and finished so as to have a flush look which includes filling and finishing the tapered and square edges of the boards with jointing compound, joint paper tape and two coats of drywall topcoat suitable for Gypboard complete at all levels as specified and directed. (For light fittings, grill diffusers etc. cut out to be made with the frame of perimeter channel supported suitably and measured and paid separately as and where necessary). (Glass wool to be measured and paid separately). ( E ) M/F Frame Work with Acoustic Type Slit Gypboard (Louvertone) Tiles (NRC value 0.72 with 50mm glass wool mat backing) 12.5mm thick.

Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) pre-coated G.I. angle size 24mmx24mmx80mm thick fixed to the brick wall/ partition at the perimeter of ceiling with nylon sleeves and screws, at 610mm c/c. Then suspending main 'T' section (bottom pre-coated) size 24mmx38mmx0.70mm and 3600mm long from the soffit in one direction with the help of metal Rawl Plug. Soffit cleat and G.I. Rod 4mm diameter with galvanised level clip 1220mm c/c G.I. cross ( H ) BPB Grid ceiling system with Fabric Based Sound absorb Panel (595mmx595mm).

Providing two coats of Birla White Wall Care Putty (Water Resistant White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm) (i) Thickness = 1.5 mm thick

Diluting and injecting aqueous emulsion for post constructional anti - termite treatment (necessary tools and accessories to be supplied by the contractors). Treatment at points of contact of wood work by aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or equivalent) and water @ 0.50 litre/hole by drilling 6mm dia holes at downward angle of 45 degree at 150mm centre to centre and sealing the same. i) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Extra over item no 13.4.7 above for every subsequent coat of wall painting with Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac). (i).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Providing fitting and fixing Vitreous china Dual Flush / Floor Mounted Coupled / Extended water closet (European type W.C pan 400mm high) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately) iii) Jaquar make a) White (ix) Kubix (Cat. No. KUS-WHT-0203) (inclusive of seat cover and fittings)

Providing fitting and fixing Vitreous china Dual Flush / Floor Mounted Coupled / Extended water closet (European type W.C pan 400mm high) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band wit iii) Jaquar make a) White (vii) Kubix (Cat. No.KUS-WHT-0311) (inclusive of seat cover and fittings)

Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug, PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) Corner Basin Jaquar make (a) White (i) Claret 560 x 430 (Cat. No.10076)

Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug, PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) Table Top Basin Jaquar make (iii) Lyric (Cat. No. LYS-WHT-0555)

Providing fitting & fixing stainless steel kitchen sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately (B) Nirali (xv) Nexus Big (Bowl Size - 560 x 410 x 230) Glossy

Providing fitting and fixing Decorative Mirror complete as directed and specified. (b) Swivel Mirror (Cat. No.ACN-1195N)

Providing, fitting and fixing Chrome Plated towel ring complete as directed and specified. (a) Jaquar make (iv) Kubix towel ring square (Cat.No.AKB-35721)

Providing, fitting and fixing Chrome Plated TOILET PAPER holder complete as directed and specified. (a) Jaquar make (ii) Continental toilet paper holder with flap (Cat.No. ACN-1153N)

Providing, fitting and fixing Chrome Plated towel ring complete as directed and specified (a) Jaquar Make (iv) Kubix towel ring square (Cat.No.AKB-35721)

Providing, fitting and fixing Chrome Plated waste coupling complete as directed and specified. (a) Jaquar Make (i) 32mm (HT/FT) (Cat.No.ALD-705 / 709)

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

(vi) 50mm dia

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

(vi) 50mm dia

Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fiting and fixing PVC coupler of (Supreme / Prince)or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately) (II) Jaquare make ii)C.P.2-way bibcock with wall flange

Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified.(G.I. & C.P pipes will be measured and paid separately) (I) Jaquar (iii) 15mm dia(Concealed stop cock reduced body )

Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed. (II) Jaguar make (b)Long neck with aerator

Supplying fitting and fixing Chrome Plated (C.P.) sink cock of approved brand as directed and specified. (G.I. & C.P pipes will be measured and paid separately) (VIII) GROHE brand Sink Cock Wall Mounted. Cat No-31225000 make Chrome Plated (CP) sink Cock.

Supplying fitting and fixing Chrome Plated (C.P.) shower 15mm dia. Of approved brand as directed and specified. (Pipes will be measured and paid separately) (III) Jaquar make b) Queen's Collection (i) Overhead rose shower with revolving joint & 150mm long swivel shower arm

Supplying, fitting and fixing Chrome Plated (C.P.) basin mixer complete as directed. (III)Jaquar make (For VIP use. Prior approval of Chief Engineer PWD (Bldg) must be taken before use) vi) 3-Hole basin mixer with popup waste system Cat No. 191

Providing, fitting and fixing CP soap tray / soap dish complete as directed and specified. (i) Jaquar Make (a) Continental (Cat.No.ACN-1331N)

Supplying, fitting and fixing Chrome Plated (C.P.) wall mixer complete as directed. (i) Jaquar Make v) Wall mixer 3 in 1 system with provision for both telephonic shower and overhead shower complete with 115mm long bend pipe Cat No.1119

Providing and fixing Chlorinated Polyvinyle Chloride (CPVC) Pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipe (B) Concealed pipe with cutting chases & making good the walls b) 20 mm nominal outer dia pipe

c) 25 mm nominal outer dia pipe

Providing,and Fixing in position wall panelling at interior partition walls, columns, chowkats etc. wall made of sal wood frame work, section 45 x 35 mm comperising of vertical and horizental at 600mm c/c or part thereof both deriction fixed firmly to floors and walls with 19 mm thick solied plywood board (Green/ Century/ Archid or equivalent) on one side of the wall and finishing with 4mm thick Natural veneer (Green/ Century/ Archid or equivalent) of approved shade with high gloss PU polish make as per design fixed with necessary adhesive complete as specified and directed by the department.

Providing, Fixing and fixing PVC panels for wall and ceiling (plain) with material & installation including labour carriage etc. as directed and specified.

Supplying,fitting and fixing Johnson Zebra Roller blinds(Combi Blckout) make and shade, design as per choce completye asspecified and directed by the department at all levels.

Providing and Furniture constructing Erecting making of U Shaped Low height storage ( Under Counter slab) of width and size (4000x950x600) (with top, sides and bottom in 19mm thich bwr ply,back in 19mm thick commercial ply, intermeddiates in 19mm thick ply shutter in 19mm thick ply grade block boark. All external surface to be finished in approved 1mm thick sunmica(high gloss).Rate to include hardware such as approved locks, auto closing hinges for shutters, approved handles, door stop, bolt, etc. complete.

Finishing of 35mm thick flush Door bothside with 6mm Plyboard Pasting and 1.5mm decorative laminate Pasting, finished with PU polish as per desired colour and shade as per Archietcts instructions and provided with Concealed Door Closure, Magnetic Door Stopper, 125mm long 2.9mm thick Heavy Duty S.S Bearing Hinge, Mortice Lock with Handle (All fittings to be of DORMA make as specified in the drawings), complete with all other necessary hardwares as per design, specified and directed by the department/conultant. A) With Teak wood / Sissu wood. (ii) 35 mm thick.

PRODUCT- AL-60 WORKSTATION Table top and 1200HT Partitions Specification: Partition: AL 60, Height 1200 mm Table top : 25mm thick Pre-laminate particle board finished with 2mm edge lipping. Tile Finishes: Partition : Partition is made of 60mm thick with fabric above and lamiante below the table top. Fabric magnetic and laminate board markers are provided for each workstation. Return and end screen: 525 L x 12 mm fabric magnetic screens. Support : MS Brackets and gable ends Wire Management : Grommet Hole provided on table top. Raceway provided below table top. MOBILE PEDESTAL 2D+1F SIZE: 400W x 450D x 600HT Pedestal : Pedestal are made of 18mm thick PLB with 2 drawer units and 1 filling folder unit. The Drawer units are made mobile with the use of castors. The drawer units are provi ded finger grooved handle and suitable locks. CPU TROLLEY AND KEYBOARD TRAY Make: Featherlite

1200 L x 600 D x 750 Ht

Visitor Module table & Reception Table Model: Edge Table Specification Table top 25 mm thick pre laminated board with 2 mm edge lipping. Supported on: 50 x 50 ms square powder coated legs. Front Modesty Wire management: race way below table top With gromet hole. MOBILE PEDESTAL 2D+1F SIZE: 400W x 450D x 600HT Pedestal : Pedestal are made of 18mm thick PLB with 2 drawer units and 1 filling folder unit. The Drawer units are made mobile with the use of castors. The drawer units are provi ded finger grooved handle and suitable locks. CPU TROLLEY AND KEYBOARD TRAY Make: Featherlite Main table size: 1500 x 600 x 750 Ht Side table size: 900 x 450 x 750 Ht With Return Screen.

Cabin Table Model : Versaline Table "Main table size 1800x900x750Ht side size:900x450x750Ht Specification: TableTop-25mmThick Pre-Laminated Particle Board (PLPB) finished with 2mm thick PVC Edge Banding SUPPORTS-Supported on 25mm thick Pre-Laminated Particle Board (PLPB) Gable Ends & 18mm thick Pre- Laminated Particle Board Modesty panel, with suitable spacers & levellers. PEDESTAL UNITS Made of 18mm Thick Pre- Laminated Particle Board board with 2 Equal Drawer + 1 Filing Drawer arrangement. Castors are provided for easy mobility of the pedestal. Recessed Aluminium handles, central locking system & other necessary hardware are provided.CPU TROLLEY AND KEYBOARD TRAY

Cabin Table Model: Versaline Table Main table size: 1800 x 900 x 750 Ht Side table size: 900 x 450 x 750 Ht Specification: TABLE TOP- 25mm Thick Pre-Laminated Particle Board(PLPB) finished with 2mm thick PVC Edge Banding. SUPPORTS- Supported on 25mm thick Pre- Laminated Particle Board(PLPB) Gable Ends & 18mm thick Pre-Laminated Particle Board Modesty panel, with suitable spacers & levellers. PEDESTAL UNITS Made of 18mm Thick Pre-Laminated Particle Board board with 2 Equal Drawer + 1 Filing Drawer arrangement. Castors are provided for easy mobility of the pedestal. Recessed Aluminium handles, central locking system & other necessary hardware are provided. CPU TROLLEY AND KEYBOARD TRAY Make: Featherlite

Model: Senate HT-501-A Size: 2200L x 800 D x 780 H Side Unit: 1010 W x 500 D x 640 H Specification: Material: MDF + particle board of 50 mm thickness. Surface finsish: Melamine Wire manager included. Color: Dark walnut Make: Featherlite

Storage Unit 1200 Ht Model: Edge Storages Size: 750 x 450 x 1200 mm ht Storage : Storage is made of 18mm PLB with openable shutters, adjustable shelves, auto closing hinges, locking mechanism and finger groved handles. Make: Featherlite

Superintendent's Chair Model: Optima HB OC-1 High mesh back chair Adjustable Lunbar support Seat slide mechanism 3 ways adjustable arms Multilocking mechanism Chrome base Make: Featherlite

Superintendent's Visitor's Chair Model: Astro VA Medium mesh back chair Additional lumbar support Fixed arms Sledge base Make: Featherlite

Cabin Chair Model: Astro Hb High mesh back chair Additional lumbar support Single lock synchro mechanism Adjustable arms Nylon base Make: Featherlite

Visitor's Module Table's Chair Model: Astro MB Medium mesh back chair Additional lumbar support Single lock synchro mechanism Adjustable arms Nylon base Make: Featherlite

Cabin visitor's Chair Model: Smart VA Low mesh back chair Powder caoted four legs Make: Featherlite

Workstation & Reception Chairs Model: Contact Project MB Medium mesh back chair Single lock synchro mechanism Fixed arms Nylon base Make: Featherlite

Sofa Option 1 Model: 238 Pearl 1S Single seater Leatherette sofa Chrome frame Chrome legs Make: Featherlite

Supplying of Sofa Couch as specified and directed by the department/conultant. 5 seater sofa Leatherette sofa Chrome frame Chrome Legs Make:- Featherlite

Supplying of Sofa Couch as specified and directed by the department/conultant. 3 seater sofa Leatherette sofa Chrome frame Chrome Legs Make:- Featherlite

Sri Rajdeep Bezbaruah