Loading
Loading…
Loading…
Tender Value
₹2.4 Cr
EMD Value
₹2.7 L
Closing Date
9 Mar 2026, 12:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
AEN TENDER
18 conditions · 7 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less, where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. For more details see Bid Documents & GCC/2022 with up to date correction slips, amendment & modifications.
(a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender. (b) (1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender.
SIMILAR NATURE OF WORK FOR THIS TENDER IS " EXECUTION OF ANY CIVIL ENGINEERING WORK ".
Work experience certificate from private individual shall not be considered. However,in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Tenderer has to produce supportive documents/certificates from the Organization for whom they have worked along with the tender offer. Certificates from Private individual/Private Limited Company/Public Limited Company (Private Sector) for whom such work are executed shall not be accepted except provision mentioned under note for technical eligibility criteria. Certificates from Govt./Semi Govt./PSU/Govt. Autonomous bodies/Public Limited Company (Govt. Sector) will only be accepted.
In support of fulfillment of specified minimum technical eligibility criteria i.e completion of the similar nature of work, the tenderer has to submit the credential certificate [scanned copy in PDF format of the original document] with their e-offer. TENDERS NOT ACCOMPANIED BY DOCUMENTARY EVIDENCE IN SUPPORT OF ELIGIBILITY CRITERIA FOR SIMILAR NATURE OF THE WORK WILL BE SUMMARILY REJECTED.
For more details see Bid Documents & GCC/2022 with up to date correction slips, amendment & modifications.
58 conditions · 4 needing a document upload
*LETTER OF CREDIT: To be followed as per GCC/2022 along with up to date correction slips, amendment/updated/revised and modification.
Demand for Financial criteria, Association with Railway Officers, List of Arbitration cases, Court cases and Mandate for NEFT are to be uploaded with a scanned copy duly filled and signed as per Annexure IV, V, VI, VII & VIII respectively. These annexures are vailable in View Document Menu at Home page and is downloadable. The details of uploaded documents should be produced whenever demanded for verification on written request at any point of tender and contract within 07 days.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Replacement of dilapidated/old pipe lines at Gardiner Road to Strachey Road and Station Colony etc. & improvement of staff quarters in pearce road in connection with improvement of various staff amenities at Liluah under CWM/LLH
Engg-Pipestaffqr-25-26LLH~ER
Engg-Pipestaffqr-25-26LLH
Open
Works - General
270 Days
Howrah, West Bengal
₹0
₹2.7 L
9 Mar 2026
12 Feb 2026
23 Feb 2026
173 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 2,35,30,878.55 | ||
| — | 250.00 | — | — | ||
| EARTH WORK // General // Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. // All kinds of soil. | — | — | — | 58,567.5 | |
| — | 150.00 | — | — | ||
| EARTH WORK // General // Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. | — | — | — | 26,460 | |
| — | 50.00 | — | — | ||
| EARTH WORK // General // Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. | — | — | — | 95,568.75 | |
| — | 5.00 | — | — | ||
| CONCRETE WORK // CEMENT CONCRETE (CAST IN SITU) // Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : // 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | — | — | — | 35,453.25 | |
| — | 10.00 | — | — | ||
| CONCRETE WORK // CEMENT CONCRETE (CAST IN SITU) // Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : // 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) | — | — | — | 65,652.3 | |
| — | 10.00 | — | — | ||
| REINFORCEMENT CEMENT CONCRETE // CAST IN SITU // Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : // 1:1.5:3 (1 cement : 1.5 coarse sand (zone- III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | — | — | — | 81,411.75 | |
| — | 5.00 | — | — | ||
| REINFORCEMENT CEMENT CONCRETE // CAST IN SITU // Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : // 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | — | — | — | 48,838.28 | |
| — | 5.00 | — | — | ||
| REINFORCEMENT CEMENT CONCRETE // CAST IN SITU // Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). | — | — | — | 51,774.75 | |
| — | 50.00 | — | — | ||
| REINFORCEMENT CEMENT CONCRETE // FORM WORK // Centering and shuttering including strutting, propping etc. and removal of form for // Foundations, footings, bases of columns, etc. for mass concrete | — | — | — | 17,646.75 | |
| — | 100.00 | — | — | ||
| REINFORCEMENT CEMENT CONCRETE // FORM WORK // Centering and shuttering including strutting, propping etc. and removal of form for // Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. | — | — | — | 75,825 | |
| — | 80.00 | — | — | ||
| REINFORCEMENT CEMENT CONCRETE // FORM WORK // Centering and shuttering including strutting, propping etc. and removal of form for // Suspended floors, roofs, landings, balconies and access platform | — | — | — | 66,762 | |
| — | 60.00 | — | — | ||
| REINFORCEMENT CEMENT CONCRETE // FORM WORK // Centering and shuttering including strutting, propping etc. and removal of form for // Lintels, beams, plinth beams, girders, bressummers and cantilevers | — | — | — | 39,765.6 | |
| — | 50.00 | — | — | ||
| REINFORCEMENT CEMENT CONCRETE // FORM WORK // Centering and shuttering including strutting, propping etc. and removal of form for // Columns, Pillars, Piers, Abutments, Posts and Struts | — | — | — | 43,258.5 | |
| — | 5.00 | — | — | ||
| REINFORCEMENT CEMENT CONCRETE // FORM WORK // Centering and shuttering including strutting, propping etc. and removal of form for // Weather shade, Chajjas, corbels etc., including edges | — | — | — | 4,279.95 | |
| — | 5.00 | — | — | ||
| REINFORCEMENT CEMENT CONCRETE // PRE-CAST RCC // Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). | — | — | — | 47,636.55 | |
| — | 865.00 | — | — | ||
| REINFORCEMENT CEMENT CONCRETE // STEEL REINFORCEMENT // Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. // Thermo-Mechanically Treated bars of grade Fe-500D or more. | — | — | — | 83,961.23 | |
| — | 1300.00 | — | — | ||
| REINFORCEMENT CEMENT CONCRETE // STEEL REINFORCEMENT // Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. // Thermo-Mechanically Treated bars of grade Fe-500D or more. | — | — | — | 1,26,184.5 | |
| — | 50.00 | — | — | ||
| MASONRY WORK // General // Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: // Cement mortar 1:4 (1 cement : 4 coarse sand) | — | — | — | 3,31,679.25 | |
| — | 80.00 | — | — | ||
| MASONRY WORK // General // Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : // Cement mortar 1:6 (1 cement : 6 coarse sand) | — | — | — | 6,55,628.4 | |
| — | 20.00 | — | — | ||
| MASONRY WORK // HALF BRICK MASONRY // Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. // Cement mortar 1:4 (1 cement :4 coarse sand) | — | — | — | 20,228.4 | |
| — | 5.00 | — | — | ||
| CLADDING WORK // General // Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels // Granite stone slab all colour and texture except black, Cherry/Ruby red // Area of slab over 0.50 sqm | — | — | — | 17,319.15 | |
| — | 20.00 | — | — | ||
| CLADDING WORK // General // Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. // Granite work | — | — | — | 9,197.1 | |
| — | 250.00 | — | — | ||
| CLADDING WORK // STONE WORK DRY CLADDING // Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. | — | — | — | 2,85,288.75 | |
| — | 9.00 | — | — | ||
| WOOD AND P.V.C. WORK // FRAMES AND TRUSSES // Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). // Sal wood | — | — | — | 9,43,814.43 | |
| — | 400.00 | — | — | ||
| WOOD AND P.V.C. WORK // FRAMES AND TRUSSES // Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. // Kiln seasoned and chemically treated hollock wood // 30 mm thick shutters | — | — | — | 9,63,666 | |
| — | 2200.00 | — | — | ||
| WOOD AND P.V.C. WORK // MISCELLANEOUS-WOOD WORK // Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. // Fixed to openings /wooden frames with rawl plugs screws etc. | — | — | — | 4,71,933 | |
| — | 100.00 | — | — | ||
| WOOD AND P.V.C. WORK // ANODISED ALUMINIUM FITTINGS (ALL FITTINGS SHALL BE ISI MARKED) // Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : // 250x10 mm | — | — | — | 10,363.5 | |
| — | 150.00 | — | — | ||
| WOOD AND P.V.C. WORK // ANODISED ALUMINIUM FITTINGS (ALL FITTINGS SHALL BE ISI MARKED) // Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : // 100x10 mm | — | — | — | 8,734.5 | |
| — | 100.00 | — | — | ||
| WOOD AND P.V.C. WORK // ANODISED ALUMINIUM FITTINGS (ALL FITTINGS SHALL BE ISI MARKED) // Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : // 125 mm | — | — | — | 5,962.5 | |
| — | 250.00 | — | — | ||
| WOOD AND P.V.C. WORK // GYPSUM BOARD PARTITIONS // Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineer- in-Charge. | — | — | — | 1,10,857.5 | |
| — | 85.00 | — | — | ||
| WOOD AND P.V.C. WORK // GYPSUM BOARD PARTITIONS // Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, panelling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. // 30 mm thick plain PVC door shutters | — | — | — | 2,43,495.67 | |
| — | 1250.00 | — | — | ||
| STEEL WORK // General // Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | — | — | — | 1,32,018.75 | |
| — | 15.00 | — | — | ||
| STEEL WORK // General // Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. | — | — | — | 1,54,434.6 | |
| — | 150.00 | — | — | ||
| STEEL WORK // General // Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. // Hot finished welded type tubes | — | — | — | 26,244 | |
| — | 200.00 | — | — | ||
| FLOORING // General // Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks. | — | — | — | 1,42,569 | |
| — | 125.00 | — | — | ||
| FLOORING // CERAMIC GLAZED TILES // Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. | — | — | — | 1,23,361.88 | |
| — | 500.00 | — | — | ||
| FLOORING // VITRIFIED FLOOR TILES // Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. // Size of Tile 600x600 mm | — | — | — | 6,99,052.5 | |
| — | 50.00 | — | — | ||
| ROOFING // SHEET ROOFING // Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. // 0.63 mm thick with zinc coating not less than 275 gm/ m2 | — | — | — | 48,944.25 | |
| — | 1200.00 | — | — | ||
| ROOFING // RAIN WATER SPOUT AND PIPE // Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. // 110 mm diameter | — | — | — | 4,07,592 | |
| — | 100.00 | — | — | ||
| ROOFING // RAIN WATER SPOUT AND PIPE // Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. // Single tee with door // 110x110x110 mm | — | — | — | 21,073.5 | |
| — | 100.00 | — | — | ||
| ROOFING // RAIN WATER SPOUT AND PIPE // Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. // Bend 87.5 degree // 110 mm bend | — | — | — | 13,531.5 | |
| — | 3000.00 | — | — | ||
| FINISHING // CEMENT PLASTER (IN FINE SAND) // 12 mm cement plaster of mix : // 1:6 (1 cement: 6 fine sand) | — | — | — | 9,00,045 | |
| — | 3000.00 | — | — | ||
| FINISHING // CEMENT PLASTER (IN FINE SAND) // 15 mm cement plaster on the rough side of single or half brick wall of mix : // 1:6 (1 cement: 6 fine sand) | — | — | — | 10,34,100 | |
| — | 50.00 | — | — | ||
| FINISHING // CEMENT PLASTER WITH A FLOATING COAT OF NEAT CEMENT // 12 mm cement plaster finished with a floating coat of neat cement of mix : // 1:4 (1 cement: 4 fine sand) | — | — | — | 19,149.75 | |
| — | 300.00 | — | — | ||
| FINISHING // 6 mm CEMENT PLASTER // 6 mm cement plaster of mix : // 1:3 (1 cement : 3 fine sand) | — | — | — | 81,121.5 | |
| — | 3300.00 | — | — | ||
| FINISHING // INTERIOR FINISHING // Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : // New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre | — | — | — | 5,51,380.5 | |
| — | 3000.00 | — | — | ||
| FINISHING // EXTERIOR FINISHING // Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: // New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) | — | — | — | 4,61,970 | |
| — | 1600.00 | — | — | ||
| FINISHING // EXTERIOR FINISHING // Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : // Two or more coats on new work | — | — | — | 2,24,496 | |
| — | 7150.00 | — | — | ||
| REPAIRS TO BUILDING // ROUTINE MAINTENANCE WORK // Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25 degreeC, 0.87 - 0.89 kg/litre and viscosity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23 degreeC as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150 degreeC. Cold flexibility shall be upto -2 degreeC when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : // 3 mm thick | — | — | — | 34,58,490.75 | |
| — | 20.00 | — | — | ||
| DISMANTLING AND DEMOLISHING // General // Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. // In cement mortar | — | — | — | 37,083.6 | |
| 1000 Nos. | 4500.00 | — | — | ||
| DISMANTLING AND DEMOLISHING // General // Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured): // From brick work in cement mortar | — | — | — | 27,138.24 | |
| — | 210.00 | — | — | ||
| DISMANTLING AND DEMOLISHING // General // Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in: // Channels, angles, tees and flats | — | — | — | 434.7 | |
| — | 100.00 | — | — | ||
| DISMANTLING AND DEMOLISHING // General // Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. | — | — | — | 508.5 | |
| — | 50.00 | — | — | ||
| DISMANTLING AND DEMOLISHING // General // Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: // G.S. Sheet | — | — | — | 7,422.75 | |
| — | 50.00 | — | — | ||
| DISMANTLING AND DEMOLISHING // General // Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer- in-charge, beyond 50 m initial lead, for all leads including all lifts involved. | — | — | — | 11,877.75 | |
| — | 10.00 | — | — | ||
| SANITARY INSTALLATIONS // General // Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231,with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: // White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests | — | — | — | 60,906.6 | |
| — | 10.00 | — | — | ||
| SANITARY INSTALLATIONS // General // Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : // W.C. pan with ISI marked white solid plastic seat and lid | — | — | — | 58,639.95 | |
| — | 10.00 | — | — | ||
| SANITARY INSTALLATIONS // General // Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: // White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps | — | — | — | 23,839.65 | |
| — | 5.00 | — | — | ||
| SANITARY INSTALLATIONS // General // Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively. | — | — | — | 7,420.27 | |
| — | 15.00 | — | — | ||
| SANITARY INSTALLATIONS // General // Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. // Flexible pipe // 32 mm dia | — | — | — | 1,613.92 | |
| — | 20.00 | — | — | ||
| SANITARY INSTALLATIONS // General // Providing and fixing 100 mm sand cast Iron grating for gully trap. | — | — | — | 958.5 | |
| — | 5.00 | — | — | ||
| SANITARY INSTALLATIONS // General // Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. // 100x100x100 mm // Sand cast iron S&S as per IS - 1729 | — | — | — | 3,269.47 | |
| — | 2000.00 | — | — | ||
| WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. ( Internal work - Exposed on wall ) // 15 mm dia nominal bore | — | — | — | 6,59,520 | |
| — | 2000.00 | — | — | ||
| WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. ( Internal work - Exposed on wall ) // 20 mm dia nominal bore | — | — | — | 7,87,140 | |
| — | 2000.00 | — | — | ||
| WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. ( Internal work - Exposed on wall ) // 25 mm dia nominal bore | — | — | — | 9,93,060 | |
| — | 2000.00 | — | — | ||
| WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. ( Internal work - Exposed on wall ) // 40 mm dia nominal bore | — | — | — | 14,61,420 | |
| — | 50.00 | — | — | ||
| WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. ( Internal work - Exposed on wall ) // 50 mm dia nominal bore | — | — | — | 47,175.75 | |
| — | 1000.00 | — | — | ||
| WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work // 25 mm dia nominal bore | — | — | — | 4,20,975 | |
| — | 1000.00 | — | — | ||
| WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work // 40 mm dia nominal bore | — | — | — | 5,55,345 | |
| — | 50.00 | — | — | ||
| WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work // 50 mm dia nominal bore | — | — | — | 34,296.75 | |
| — | 1000.00 | — | — | ||
| WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work // 80 mm dia nominal bore | — | — | — | 9,37,530 | |
| — | 5.00 | — | — | ||
| WATER SUPPLY // BRASS FITTINGS // Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet // 150 mm diameter | — | — | — | 1,000.58 | |
| — | 6.00 | — | — | ||
| WATER SUPPLY // C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES // Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : // 100 mm diameter // Class I | — | — | — | 25,872.48 | |
| — | 8.00 | — | — | ||
| WATER SUPPLY // C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES // Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : // 150 mm diameter // Class I | — | — | — | 50,159.16 | |
| — | 6.00 | — | — | ||
| WATER SUPPLY // C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES // Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : // 200 mm diameter // Class I | — | — | — | 73,195.38 | |
| — | 25.00 | — | — | ||
| WATER SUPPLY // C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES // Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : // 15 mm nominal bore | — | — | — | 7,162.88 | |
| — | 25.00 | — | — | ||
| WATER SUPPLY // C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES // Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : // 20 mm nominal bore | — | — | — | 7,803 | |
| — | 20.00 | — | — | ||
| WATER SUPPLY // C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES // Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : // 25 mm nominal bore | — | — | — | 7,906.5 | |
| — | 10.00 | — | — | ||
| WATER SUPPLY // C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES // Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : // 40 mm nominal bore | — | — | — | 5,681.7 | |
| — | 20000.00 | — | — | ||
| WATER SUPPLY // C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES // Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. | — | — | — | 1,98,000 | |
| — | 50.00 | — | — | ||
| WATER SUPPLY // PTMT FITTINGS // Providing and fixing PTMT bib cock of approved quality and colour. // 15 mm nominal bore, 86 mm long, weighing not less than 88 gms | — | — | — | 5,652 | |
| — | 200.00 | — | — | ||
| WATER SUPPLY // AIR VALVE & WATER METER (BULK TYPE) // Providing and laying Double Flanged (screwed / welded) Centrifugally (Spun) Cast Iron, Class B (IS : 1536) : // 200 mm dia C.I. Double Flanged Pipe | — | — | — | 8,99,253 | |
| — | 500.00 | — | — | ||
| WATER SUPPLY // AIR VALVE & WATER METER (BULK TYPE) // Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 : // 100 mm dia Ductile Iron Class K-7 pipes | — | — | — | 5,66,010 | |
| — | 650.00 | — | — | ||
| WATER SUPPLY // AIR VALVE & WATER METER (BULK TYPE) // Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 : // 150 mm dia Ductile Iron Class K-7 pipes | — | — | — | 10,46,916 | |
| — | 405.00 | — | — | ||
| WATER SUPPLY // AIR VALVE & WATER METER (BULK TYPE) // Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 : // 200 mm dia Ductile Iron Class K-7 pipes | — | — | — | 8,48,610.68 | |
| — | 2100.00 | — | — | ||
| DISMANTLING AND DEMOLISHING // General // Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. | — | — | — | 1,03,288.5 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .