PROVN OF AIR CONDITIONED MEDICAL STORE FOR STORAGE OF CRITICAL MEDICINES AT 7 AFH KANPUR CANTT

Amount

AIR CONDITIONING Supply, install, commissioning and testing of Air Cooled Packaged Air Conditioners, comprising of Hermetically sealed scroll compressors with microprocessor based control, including copper refrigerant piping, electrical interconnection between indoor and outdoor units, suitable for operation on 407c/410a non CFC refrigerant and of nominal capacity of 11 TR, copper cooling coil, expansion valve, LP/HP cutout etc all assembled in sturdy and well finished housing, internally insulated wire, ready for installation at one point with suction/dishcharge connection complete with copper piping and insulation, anti vibration/isolation pads including suitable size of copper cable and controls complete all as specified and directed. Note:- (i) Supply & air return ducting to be measured & paid separtely. (ii) Earthing for each machine shall be measured & paid separately.

Supply, assembly and erection of GI sheet with TDF flanged rectangular/square duct made out of 'L' shaped hollow profile, duly factory boxed, incl all accessories such as corner, cleat, carriage bolt, Gasket and appropriate sealent on longitudinal joints etc complete of size 22 gaugethick GI sheet complete all as specified and directed.

S&F crosslink XLPE foam nitrile rubber insulated on duct surface of size 8 to 9 mm thick on top, bottom and sides with adhesive and blank taping complete all as specified and directed.

M&L hessian cloth lining of approved quality all around the duct with suitable size screws complete all as specified and directed.

M & L aluminium extruded powder coated return/supply air grill (ISI Marked) of rectangular size all as specified and directed.

Excavating in trenches n.exc. 1.5 m wide and n.exc.1.5m in depth for laying of XLPE insulated Cable including getting out in soft/loose soil complete all as specified & directed.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exceeding 25 cm complete all as specified and directed

Removing excavated material n.exc. 50m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M&L spreading & leveling dry clean Ganga sand in trenches for cushioning of UG cable complete all as specified and directed. (Note: Punned thickness shall be measured for payment.)

M&L well burnt sub class 'B' bricks old size, with width equal to the length of the brick in trenches for cable protection of LT Cables complete all as specified and directed.

S&F 50 mm nominal bore dia light grade galvanised mild steel tubing with all fittings and fixed to poles / walls with mild steel clamps, bolts, nuts and washers including two coats synthetic enamel paint over a coat of red oxide primer on steel clamps complete all as spefified and directed.

All as per item No 11 but size 80mm bore dia.

Supply and fixed XLPE insulated , screened, PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty with aluminium conductor 1100 volts grade cross sectional area 25 sq mm 3.5 core ,laid in trenches/ducts /encased in GI pipe /fixed to pole including taking out of existing unserviceable cable/OH conductor all as specified and directed.

M& L earthing complete with galvanized steel earth plate electrode 60cm x60 cm x6.0 mm thick buried directly in ground (earth pit not less than 2.25 Mtrs deep below ground level) with top edge of the plate not less than 1.50 Mtr below normal ground level connected to galvanized earth lead strip 32x6mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 connected to earthing test point, including testing on completion including earth chamber in PCC (1:3:6) type C-2 with using 40mm graded stone aggregate and 40mm thick RCC cover 1:2:4 type B1 using 20mm graded stone aggregate reinforced with 8 mm dia TMT bars @ 100mm C/C with two no’s fitting handle, GI pipe 20mm dia light grade with funnel & wire mesh for watering and 40mm dia light grade GI pipe for earth strip 32x6mm protection etc. complete all as specified and directed.

B/R WORK Taking down chawkhats or frame (without taking off shutters from the frames) but not exc 1.50 each complete all as specified & directed.

Taking down chowkats or frame (without taking off shutters from the frames) exc. 1.5 sq. m but not exc 4 sq. m each complete all as specified and directed.

Supply & fix aluminium anodised section (minimum thickness of anodising 15 micron) for window/ventilator etc of sliding type comprising frame, shutters, locking arrangements including necessary joining, glazing clips, neoprene beading, glazing pin, screw, rollers, handle etc complet all as specified and dircted. Note:- (i) Glazing shall be measured seperately. (ii) Item shall be paid as per weight of lauminium section. (iii) Rate quoted shall be inclusive of neoprene beading, glazing clips, screw etc as required which not be measured for arriving the weight. (iv) Rate shall be inclusive of locking arrangement including complete packing with silicon gel around contacting surface of aluminum and including matching the existing surface area complete all as specified and dircted. (v) Aluminium window/ventilator etc to be fixed with cadmium plated screw not more than 300mm c/c.

Supply and fixed powder coated aluminium section for sliding/fixed in frame/shutter for doors, partition etc with one or more rebate, including joining cleats for fixing glass etc, with or without sash bars including necessary locking arrangements, glazing clips, rubber packing, anodized aluminium snap beading, screws etc complete all as specified and directed. Note:-(i) Glazing shall be measured and paid seperately. (ii) Item shall be paid as per weight of aluminium sections as per manufacturer catalogue. However the rate quoted shall be inclusive of the cost of neoprene beading, glzaing pin, screw, appropriate handle, fitting/fixtures including cost of poweder coating to small article to match etc as rquired which shall not be measured for arriving the weight.

S&F double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F 12 mm thick pre laminated particle board interior grade prelaminated both side with decorative choice lamination complete all as specified and directed

S&F 4.8 mm thick sheet glass and including glazing aluminium beading etc exc 0.50 sqmtr each pane complete all as specified and directed.

M&L brick work with fly ash brick, old size, straight or curved on plan, exc 6m mean radius built in CM 1:6 complete all as specifeid and directed.

M&L rendering 10mm thick in CM 1:6 on other than fair face of brick/concrete surfaces of wall, finished even & smooth without using exra cement complete all as specified and directed.

M&L preparing newly plastered surface of walls applying two coats of oil emulsion distempering over a coat of chalk whitening primer complete all as specified and directed.

M&L preparing old distemped surfaces of walls by washing, rubbing down and stopping of distempered and painted surfaces and apply two coat of distemper oil emulsion (oil bound washable distemper) complete all as specified and directed.

Material & labour flase ceiling made out of 600x 600x 4 to 6 mm thick laminated designer ceiling board/tiles deep panel suspensor system made out of powder coated GI sheet main Tee of size 23.50x 40x 0.63 mm and cross tee of size 23.50 x 23.50 x0.63mm and angle size 19x 19x 0.63mm including 3 mm GI wire for suspending bolts, necessary washers, nut/cleats/pin hook etc for securing frame work to ceiling to snap grid including provn of necessary holes/cutting for providing light/fan as required inlcuding making necessary recesses/projected pattern complete all as specified and directed.

HVAC Engineering Co

M/s R.V. Constructions