REPAIR/MAINT TO TILING, FLOORING, PLUMBING ROOF TREATMENT, SANITARY FITTINGS AND CONNECTED WORKS ETC AT LAO OFFICE, MD ACCN AT DAD COMPLEX UNDER GE PANAGARH

Amount

Demolition of cement concrete (un-reinforced) not exceeding 15 cm thickness (above or below ground level) complete all as specified and directed.

M&L Hardcore of gauge n exc. 63 mm, deposited, spread and leveliled in layers n exc. 150mm thick, watered and rammed to a true surface complete all as specified & directed by Engineer-in-Charge..

M&L for providing 75 mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) in sub base of flooring complete all as specified and directed.

M&L for providing 40mm thick PCC 1:2:4 Type B0 (Using 12.5 mm graded stone aggregate) as in flooring including finishing the cement concrete surface even and smooth without using extra cement complete all as specified and directed.

M&L for 75mm thick Cement concrete type C-1, 1:3:6 (20mm graded stone aggregate) as in plinth protection and paving complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mitred/stopped ends etc.as specified & directed by Engr-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing to low lying area and rubbish off the premises complete all as specified & directed by Engineer-in-Charge..

M&L 25mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in floor for levelling course complete all as specified and directed by Egineer-in-Charge.

S&F Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed or bedding layer 15mm thick in cement mortar 1:6 laying floor finishes complete all as specified and as directed

M&L for Glazed ceramic tiles in vertical surface 300x 450x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles including C:M (1:3) Screed bed or bedding layer of mortar 10 mm thick for laying floor finishes complete all as speciified and directed.

M&L non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tiles exc. 0.11 sqm but n. exc 0.18 sqm of approved colour as in floors etc set and joined in neat cement slurry and pointed in white of coloured cement over 15mm thick sreed bed of cement mortar (1:6) complete all as specified and directed by Engr-in-Charge.

M&L 7 to 8 mm thick Vitrified Ceramic light shade tiles (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white of coloured cement to match over 15mm thick screed bed of cement mortar (1:6) complete all as speified and directed. Note : Design, shade and pattern of fixing of tiles shall be as directed.

M&L for 7-8 mm thick outdoor parking tiles of approved size 0.3 m x 0.3 m, set, jointed and pointed using with matching cement and pigment in floors, paving tc including the setting and jointing in neat cement paste and slurry 0.3 kg/Sqm over 20mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L for 25mm thick chequered cement concrete tiles of approved size, set, jointed and pointed using with grey cement and pigment in floors, paving tc including the setting and jointing in neat cement paste and slurry 0.3 kg/Sqm over 20mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L 15mm for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S & F Marble work 15 thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of green colour marble.

Supply and fixing stainless steel ( Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts cup etc complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. Note: For payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.

Rounding to edges of stone (Granite / Kota) slabs one edge, such as in steps, cooking platform and other similar situations incl polishing, complete all as specified and directed.

Taking down cement plaster of any description on concrete surfaces such as soffit of RCC slab, chajjas and brick walls etc incl raking out joints, hecking for key scrubbing down with water and removal of rubbish off the premises complete all as specified and directed.

M&L Rendering 10 mm thick cement plaster in cement mortar (1:6) on brick work or concrete surfaces including finished fair and even complete all as specified and directed.

M&L Rendering 15 mm thick with WPC on external surfaces of brick work in cement moratr (1:4) including finished fair and even complete all as specified and directed. Note : (WPC will be measured and paid separately)

Supply only Liquid water proofing compound.

M&L for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior antifungal primer applied @ 0.90 litre/ 10 sqm over new surfaces.

Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer with 1.0 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified.

M & L two coats synthetic enamel paint over a coat of red oxide primer on new steel surfaces incl preparation of surfaces over 10 cm width or girth.

M&L complete removal of existing surface prepration of old plastered surface of wall for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified & directed by Engineer-in-Charge.

Material & Labour for complete removal of existing treatment, preparation of surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer and 1.0 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressedstonework and precastconcrete articles complete all as specified and directed.

M&L, Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete, all as specified and as directed.

M&L for brick work with flyash bricks straight or corve on plan to any radius in half bricks thick walls, built in cement mortar (1:4) complete all as specified and directed.

S&F Mild Steel TMT bars 10mm and over, cut to lenghth, bent to shape requird, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clip all as directed by Engineer in Charge.

All as per item No 31 here in before but 8mm dia complete all as specified & directed by Engineer in Charge

Taking down chowkhat or frame with shutters n.exe 1.50 Sqm (without taking of shutter from frame ) each complete all as specified and directed

Taking down chowkhat or frame with shutters exe 1.50 Sqm and not 4 sqm (without taking of shutter from frame ) each complete all as specified and directed

Taking down Shutters of any description n exc 1.00 sq. m each complete all as specified & directed by Engineer-in-Charge.

M&L Chowkhat 2nd class hard wood and frames wrought , framed rebated on the solid rounded or chamfered, put together with gluepinned at joints complete all as spd and directed by Engr-In-Charge.

S&F 35mm thick 2nd class hardwood, factory made plain framed, panelled shutters (two panel), with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specifiedd and directed by Engr-In-Charge.

S&F 35mm thick 2nd class hardwood factory madeGlazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specifiedd and directed by Engr-In-Charge .

S&F Factory made single extruded WPC ( Wood polymer composite ) solid door/window and others frames/chowkhat of size 50x125 mm double shutter comprising of virgin PVC polymer of K value 58-60 (Suspension Grade ), calcium carbonate and natural fibres and non toxic additives fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS Screws having minimum frame density of 750kg/cum and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engg-in-charge.

S&F Factory made single extruded WPC ( Wood polymer composite ) solid Plain flush door shutter of 30 mm size comprising of virgin PVC polymer of K value 58-60 (Suspension Grade ), calcium carbonate and natural fibres and non toxic additives having minimum density of 650kg/cum and with property of being termite/borerproof,water/moisture proof and fire retardent and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws complete as per direction of Engg-in-charge.

S&F factory made solid PVC door frame of size 50mmx47mm made out of 5 mm plain colour PVC sheet with mild steel square tube complete as per manufacturer specification & drawing complete all as specified and directed by Engr-in-Charge.

S&F factory made solid panel PVC door shutter 30 mm thick (stiles) consisting of frame made out of mild steel tubes for top & bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm with stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and botttom rail, panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement fixing in the frame at site as per specification ,drawing complete all as specified and directed by Engr - in - Charge.

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 122 x 54 mm & sash 47 x 64 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

S&F stainless steel wire cloth of 0.36 mm nominal dia of wire and averaging of width of aperture 1.40mm, fixed with stainless steel wire staples including taking out old wire cloth complete all as specified and directed.

S & F in repairs aluminium anodised bracket suitable for fixing of 25 mm dia curtain rods complete all as specified and as directed.

S & F in repairs25 mm dia Stainless steel curtain rod complete all as specified and as directed.

M&L for framed work such as grills etc with endsof bars shouldered nd or riveed or forged into spike, framed guard bars and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

Supply and fix butt hinges 100MM, medium weight, complete all as specified & directed by Engineer-in-Charge.

Supply and fix 150 mm long aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and directed.

Supply and fix 150 mm aluminium handle cast type, anodised, complete all as specified and directed

Supply and fix 125 mm aluminium handle cast type, anodised, complete all as specified & directed by Engineer-in-Charge.

S&F 300 mm Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified & directed by Engineer-in-Charge.

S&F for 4mm thick plain sheet glass ordinary quality & glazing with oil putty n.exc 0.50 Sqm in each pane complete all as spd and directed by Engr-In-Charge .

S&F 4mm figured glass pin headed type and glazing with oil putty in square n.exc 0.50 sqm each pane complete all as specified and directed.

Taking down steel tubing having bore of pipe 15 mm and connections, including cleaning for refixing or removal to store complete all as specified & directed by Engineer-in-Charge.

Refixing old steel tubing and connections in new or old position (Walls, ceiling, floors, etc. bore of pipe 15 mm and connections complete all as specified & directed by Engineer-in-Charge.

Taking down steel tubing having bore of pipe 20 mm and connections, including cleaning for refixing or removal to store

Refixing old steel tubing and connections in new or old position (Walls, ceiling, floors, etc. bore of pipe 20 mm and connections all as directed and as specified.

S & F CPVC pipes laid in floors/trenches with outer dia of pipe 16 mm dia with all fittings and fixtures complete all as specified and as directed by Engr-in-Charge..

S & F CPVC pipes laid in floors/trenches with outer dia of pipe 20 mm dia with all fittings and fixtures complete all as specified and as directed by Engr-in-Charge..

S&F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160 mm

S&F in repair 15 mm bore stop valve cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iro pipe of for unions complete all as specified and directed.

S&F in repair grating square 150mm size of PTMT (minimum weight 100 gms) complete all as specified and directed

S&F in repairs PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified & directed by Engineer-in-Charge.

Supply and fix in repair bib taps of 15mm bore fancy type, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs closet Vitreous china squatting pan Orissa pattern of size 580x440mm white with integral foot rests (excluding flusing cistern and flush pipe) including connection to trap and to flushing pipe, antisyphonage connection pipe etc complete making good disturb surface with existing finish of floor all as specified & directed by Engineer-in-Charge.

Supply & fix in repairs vitreous china wash basin, white, flat back, size, 550X400mm including bracket for fixing 32 mm waste coupling, waste pipe etc complete all as specified & directed by Engineer-in-Charge.

Supply and fix in repair Pillar taps, 15mm bore, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'HOT or COLD' with long scrwed shanks and fly-nuts, screwed for iron pipe or for connection pipe complete all as specified and directed.

S&F in repair 125mm Brass Chromium Plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F in repair 32 mm bore Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm45gms/40mm-60 gms complete all as specified & directed by Engineer-in-Charge.

S&F in repairs, door closer aluminium body, hydrailically regulated, designation No.2, universal type, suitable for door shutters and weight between 36 to 60 kg and fixed complete all as specified and as directed.

S&F in repairs, floor door stopper over all length of cover plate 140mm of aluminium alloy body with rubber shoe and tongue, anodised, with hard drawn steel spring and fixed complete all as specified and directed.

S&F in repair mortice lock vertical type 100mm 4 lever brass fixed in aluminium door complete all as specified and directed.

Demolition of Cement Concrete (un-reinforced) of any description and in any position not otherwise specifically provided for all as specified and as directed.

M&L for grading roof in cement mortar 1:3, 25mm thick in edge and 50mm thick in ridge including necessary curing complete all as specified in SSR Part I clause No 11.42.2 complete all as specified & directed by Engineer-in-Charge.

M & L for providing water proofing treatment with a layer of APP based polymeric membrane, 3 mm thick (minimum), weighing not less than 3.60 kg/Sqm reinforced with polymer non woven fabric (weighing not less than 160 gm/ Sqm) shall be applied over one coat of cold bituminious primer @ 0.40 ltr/ Sqm ( membrane shall be laid using butane torch and sealing all joints etc, complete all as specified and directed .( Note: The overlaps shall be of minimum 75 mm on longitudinal direction and 100 mm on transverse direction) complete all as specified and directed.

M & L for one coat of aluminium paint over APP membrane, complete all as specified and as directed.

M/s Bhola Shah Bansi Lall (BID ID -3379363)

ANIMA ENTERPRISE (BID ID -3377902)