SPL REPAIR TO BLDG NO P09 OR LIVING ACCN AT FD REGT UNDER GE NORTH AKHNOOR

Taking down old treatment including padding, removing existing bitumen felt treatment including brushing, cleaning top surface of roof slab, brooming etc complete all as specified and directed.

Rendering 15 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces including finishing the surface fair and even on roof slab complete all as specified and as directed.

Water proofing treatment to RCC roof slab including parapet as under :- (a) Ist Course : Apply a coat of bituminous primer conforming to IS-3384@ 0.40 Kg /Sqm on prepared surface of plaster and after drying of primer, apply a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.2 Kg/sqm on plastered surfaces. (b) 2nd Course : APP (Atactic Polypropylene) modified polymeric membrane, 5 layered, 3 mm thick weight not less than 4.0 Kg/Sqm with 160 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 150 mm end overlap, membrane has to be laid with LPG torch and overlap sealed and finished neat, all joints and changes in direction should be covered with cement mortar 1:3 mixed with SBR latex @200ml/bag of cement and curved before laying of membarance. (c) 3rd Course : Apply a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.2 Kg/sqm over membrane and dusted with dry sand @ 0.50 to 1 Kg/sqm. (i) On Non-accesible roof : After providing (a) to (c) provide aluminium paint as per manufacturer instructions. (ii) Coved fillet in PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) of required radius 75mm shall be provided at the junction of roof and vertical surface such as parapet wall/mumty around opening and treatment mentioned above shall be applied followed by a cement plaster 20mm thick in cement mortar(1:6). Note : (i) Roof treatment work shall be carried out through approved manufacturers only or through their authorised personal only.

Sunken Floor treatment: Providing and laying of water proofing treatment to sunken portion by applying cement slurry mixed with acrylic based polymer modified cementitious composite compound of make as approved including demolition and filling of sunken floor . (a) First layer of slurry of cement @0.488 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.253 Kg/Sqm. This layer allowed to air cure for 4 Hours. (b) Second layer of slurry of cement @0.242 kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.125 Kg/Sqmhis layer allowed to air cure for 4 Hours. (c) 15mm plaster in CM 1:3 mixed with WP compound shall be provided while concrete is still green. (d) Joint of/Trap/WC/Soil pipes shall be properly sealed with sealing compound. Note: Plain concrete 1:4:8 type D-0 for sunken slabs shall be mixed with WP compounds as per manufacturer's instructions, before carrying out water proofing treatment the sunken slab shall be tested with water for 48 hours for any leakage /dampness is seen in ceiling below, then treatment is again carried out to RCC slab and it is again tested before passing for next stage. (The rate quoted includes water proofing compound as per manufacturers instructions).

Rendering 15mm thick on external wall surfaces (ht not exc 7 m from ground level) in cement mortar 1:4 finished fair and even without using extra cement as in roof projection/chajjas/facia incl soffit of chajjas with using GI wire netting 0.90mm dia and 12mm mesh lathing, finished even and smooth (without using extra cement), complete all as specified. Note : (i) Rate quoted are deemed to incl double scaffolding. (ii) Wire netting shall be measured and paid seperately.

Supply only GI wire mesh 0.90mm dia and 12mm mesh size all as specified and directed.

Demolition of brickwork or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.

Brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified and as directed.

Brick work with sub class B brick straight or curved on plan to any radius in half brick thick built in CM 1:4 complete all as specified and directed.

Taking down cement plaster from brick or stone walls incl racking out joints hacking for key, scrubbing down with water etc all as specified and directed.

Rendering 15 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and directed.

Rendering 10 mm thick in cement and sand mortar 1:6 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth complete all as specified and directed.

Rendering 5mm thick cement plaster with cement and sand mortar(1:3) on concrete surface as in ceiling finished even and smooth without using extra cement all as specified and directed.

Supply only integral water proofing compound as for manufacturers instructions.

Preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

Preparation of newly plastered surfaces of wall and applying two coat of cement base paint over a coat of alkali resistant primer, complete all as specified and directed.

Preparation of newly plastered surfaces of ceiling and applying three coat of white wash, complete all as specified and directed.

Complete removal of exising treatment of old surfaces complete all as specified and directed.

Applying 1mm thick wall care putty white all as specified and directed.

Preparation of surfaces of walls finished with putty and applying two coat of oil bound distemper over one coat of primer all as speicfied and directed.

Preparation of old decorated surfaces includiing brooming down or steel wire brushing, scrapping down smoke soot,moulds, moss and efforescent salts and removing oil and greasy spots and applying one coat of white wash on walls, complete all as specified and as directed.

-Ditto- All as per srl item no 21 here in before one coat on ceiling.

25 mm dia stainless steel curtain rod complete with stainless steel bracket and side clamps fixed in position by drilling holes in wall and fixing the bracket with rawl plug and SS screw, fixed in repairs all as specified and as directed.

Demolition of stone slab and tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc. complete all as specified and directed

Granite (of any type work) 20mm thick (table rubbed and polished) in steps jambs, pillars, window cills, cooking platform and like in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixure of pigment to match with shade of granite including 15mm thick screed bed of CM 1:4 after applying cement slurry @ 3 Kg/Sqm complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (Reinforcement cut as required to facilitate demolition ) complete all as specified and directed.

Reinforced cement concrete (Nominal mix), type B1, 1:2:4 (using 20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including use and waste of necessary form work complete all as specified and as directed.

25mm thick plain cement concrete 1:2:4 type B-0 (Using 12.5mm graded crushed stone aggregates) as in floor and finished even and rough to receive topping layer complete all as specified and directed.

Providing plain cement concrete type C-2, 1:3:6 ( using 40mm graded stone aggregate), 750mm wide and 50mm thick as in plinth protection laid in bays not exceeding 2 Sqm each and finishing even and fair on top without using extra cement with 6mm wide joints throughout the thickness of plinth protection in concrete bays and in between the walling and plinth protection, filling the joints with mastic filling comprising of one part of heated bitumen 85/25 or 95/10 grade and 3 parts of sand ( all by weight all as specifed and directed ).

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) in floors etc area of each tiles exceeding 0.11 Sqm but not exc 0.18 Sqm. Set and jointed in neat cement slurry and pointed in coloured cement to match including 15 mm thick screed bed in cement and sand mortar 1:4, complete all as specified and directed.

Non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) in floors etc area of each tiles exceeding 0.18 Sqm but not exc 0.36 Sqm. Set and jointed in neat cement slurry and pointed in coloured cement to match including 15 mm thick screed bed in cement and sand mortar 1:4, complete all as specified and directed.

Glazed ceramic tiles 450 x 350 x 7mm thick (coloured) on vertical surfaces such as skirting, dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

20-25 mm thick machine cut kota stone slab as in flooring, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick screed bed in cement and sand mortar 1:4 complete all as specified and as directed by . (Size of Kota Stone slab shall not to be less than 53 cm x 53 cm).

Description all as per srl Item No-35 above but in skirting/dado with & including 10mm thick rendering CM 1:4, complete all as specified and as directed by.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size. exc 1.5 Sqm and n exc 4.00 Sqm each and removing from site complete all as specified and directed.

-Ditto- all as per Srl item No. 37 here-in-before, but area not exceeding 1.5 sqm sqm each.

Taking down shutter of any description area exc 1 sqm but not exc 2.0 sqm each complete all as specified and directed.

Steel windows/ventilator (Box type) factory made glass/glazed shutter, (glass panes shall be measured and paid separately) of size 79mmx39mm,16 gauge rectangular tubular frame with side hung shutter with glazing bars 12x3mm flat iron incl box type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 100mm long including 08 mm square bar grills complete all as specified & as shown on drg No. CEUZ/TD/1302/2009 Sh no 1/1 to 1/3 .

-Ditto- all as per item No 40 here-in-before but without glazing bars.

Mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165.

Factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site. complete all as specified and directed.

Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube, supplying and fixing in opening as per specification and drawing, complete all as specified and directed.

Pressed steel frames for doors with one or more rebates of size 105x60mm including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia thresh hold bar complete all as specified and as directed.

Pressed steel frames for doors with one or more rebates of size 125x60mm including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia thresh hold bar complete all as specified and as directed.

Plain Cement Concrete 1:3:6 type C-0 (using 12.5 mm graded crushed stone aggregate) as in back filling of pressed steel frame complete all as specified and directed.

35mm thick, 2nd class hard wood plain, framed, panelled factory made shutters (two panel) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.

35 mm thick, 2nd class soft wood , glazed & skeleton factory made shutters, open rebated & prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metred beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.20(a) complete all as specified and directed.

Mild steel Butt hinges, 100 mm long medium weight, cold rolled, ISI marked complete all as specified and as directed.

Aluminium handles cast type anodised of size 150mm long ISI marked complete all as specified and as directed.

200mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified and as directed.

300mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete all as specified and directed.

03 mm thick figured (frosted) glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and as directed by.

03 mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and directed.

Galvanized mild steel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

Floor door stopper 140mm overall length of cover plate of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor complete all as specified and directed.

Preparation of new steel surfaces of any description exc 10 cm width or girth, priming with red oxide primer and painting with two coats of synthetic enamel paint complete all as specified and directed.

Painting to new wood or wood based surfaces of any description not otherwise described over 10 cm in width or girth including preparation of surfaces, priming with pink primer (one coat) finished with two coats of synthetic enamel paint complete all as specified and directed.

Preparation of old steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Preparation of old wooden surfaces exceeding 10 cms width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) 3 layered hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete all as specified and directed.

Taking up or down steel water tubing and connections of 15mm bore all as specified and directed.

Taking up or down steel water tubing and connections of 20 mm bore all as specified and directed.

Mild steel galvanized steel tubing 15mm bore medium grade with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed.

Mild steel galvanized steel tubing 20mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floorscomplete all as specified and directed.

Refixing old steel tubing and connections in new or old position on walls, ceiling or floors etc of size 15 mm bore after cleaning including provn of new fittings all as directed.

-Ditto- all as per item No.67 here- in- before but 20 mm bore.

Bib taps, fancy type chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, for bore dia of pipe 15mm, supplied and fixed in repairs complete all as specified.

Stop valves/angle valve, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions, for bore dia of pipe 15 mm, supplied and fixed in repairs complete all as specified.

15 mm dia bore stop valves (concealed type) with long shank and cup fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fixed in repairs complete all as specified and as directed.

Pillar tap fancy type capstan heads, chromium plated screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed in repairs complete all as specified and directed.

Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20 mm dia (minimum weight 210 gms) complete all as specified and directed.

20 mm bore gun metal globe or gate valve with iron wheel head screwed both end for iron pipe fixed in repairs complete all as specified and directed.

PVC valve less, Symphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete, fixed in repairs complete all as specified and as directed.

Water closet vitreous china squtting pan "Orissa Pattern" size 580 x 440 mm in any coloured with integral foot rest incl lime mortor, 'S' trap and complete all as specified, fixed in repairs complete all as specified and directed.

Vitreous china wash down water closet pan pedestal pattern including seat cover white excluding flushing cistern and flush pipe fixed in repairs complete all as specified and directed. .

Brass chromium plated health faucet with one metre long flexible tube and wall hook fixed to iron pipe fixed in repairs complete all as specified and directed.

Plastic water closet seat cover white closed pattern with flat bottom and mild steel chromium plated or aluminium hinging devices fixed in repairs complete all as specified and directed.

Vitreous china Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe), with grating and union for discharge pipe including bedding urinal against wall in cement mortar 1:2 & securing urinal to plug with brass screws fixed in repairs complete all as specified and directed.

Vitreous china wash basin, white, flat back, size 550x400mm including pillar tap, waste fitting chromium plated brass, chromium plated steel chain and rubber plug, porcelain stopper, a pair of CI brackets, waste pipe and pillar tap etc., fixed in repairs complete all as specified and as directed.

PVC connection 15mm size with PTMT nuts of length 450mm size fixed in repairs complete all as specified and directed.

Chromium plated brass towel rail 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls and fixed in repairs complete all as specified and as directed.

Brass chromium plated shower roses 125mm with or without swivel joints, including fixing to steel pipe or union fixed in repairs all as specified and directed.

Taking down eaves gutters and rain water pipe , soil and waste pipe (any size or pattern), including all fittings, heads , shoes bends , swan-necks etc complete all as specified and directed.

110mm bore PVC SWR Type-B pipes single socket in any length with rubber joints fixed in floors etc complete all as specified and directed.

110mm bore PVC SWR Type-B pipes single socket in any length with rubber joints fixed to wall with PVC/MS holder clamp etc complete all as specified and as directed.

75mm bore PVC SWR Type-B pipes single socket in any length with rubber joints fixed in floors etc all as specified and directed.

75mm bore PVC SWR Type-B pipes single socket in any length with rubber joint fixed to wall with PVC/MS holder clamp etc complete all as specified and directed.

PVC SWR reducer 110mm to 75 mm complete all as specified and directed.

PVC SWR Type-B cowls 75mm bore all as complete all as specified and directed.

110mm bore PVC Bends (any radius) diminishing pieces or tapers (larger bore measured) for pvc pipes complete all as specified and directed.

PVC (SWR) bends any radius 110mm dia with access doors complete all as specified and directed.

PVC SWR branch piece 110mm bore (single T) equal or unequal ordinary or inverted (spigot or socket type) all as specified and directed.

PVC (SWR) bends any radius 75mm dia complete all as specified and directed.

PVC (SWR) bends with access door any radius 75mm dia complete all as specified and directed.

PVC SWR branch piece 75mm bore (single T) equal or unequal ordinary or inverted (spigot or socket type) all as specified and directed.

PVC (SWR) floor traps 75mm plain with grating including joints with solvents cement fixed in repairs completed all as specified and directed.

PVC SWR branch piece 110mm bore (single Y) equal or unequal ordinary or inverted (spigot or socket type) all as specified and directed.

PVC SWR branch piece, 75 mm (single Y) equal or unequal ordinary or inverted (spigot or socket type) with oval access door fixed in repairs all as specified and directed.

Waste pipe for WHB/Urinal for 32/40mm dia fixed in repair all as specified and as directed.

Taking down carefully copper/aluminium point wiring (light,fan,bell, socket or power) complete,including fixtures and fittings such as switches, ceiling roses, holders,regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty and white cement at necessary holes for smooth finishing complete all as specified and directed.

One light point/fan /bell point controlled by one switch.

One 15 amps socket outlet point controlled by one 16 amps switch on independent board complete all as specified and directed.

Modular type switch 6 Amps, single pole,1way,1 module, 240V, with cover plate ISI Marked Complete all as specified and directed.

Modular type switch 16 Amps, single pole,1way,1 module, 240V, with cover plate ISI Marked Complete all as specified and directed.

Modular type socket shuttered type 6 Amps, 2/3 Pin combined 2 module, 240V,AC with cover plate ISI Marked Complete all as specified and directed.

Ceiling rose, 3 terminal ,PVC/polycarbonate body ISI marked, complete all as specified and directed.

LED light fitting General purpose surface and wall mounted LED batten with Aluminium housing integrated electronic driver, 20W, 4 feet and connecting up with twin core twisted copper wire from LED fitting to ceiling rose and removing old unserviceable fitting complete all as specified and directed.

LED light fitting General purpose surface and wall mounted LED batten with Aluminium housing integrated electronic driver, 10W, 4 feet and connecting up with twin core twisted copper wire from LED fitting to ceiling rose and removing old unserviceable fitting complete all as specified and directed.

LED INVERTER batten 20 w 4 feet with square profile and poly carbonate channel lithium ion battery with charging time 8 to 10 hours and backup time upto 4 hours and connecting up with twin core twisted copper wire from LED fitting to ceiling rose and removing old unserviceable fitting complete all as specified and directed.

LED bulb 12 watts, 240Volts,50Hz pin type and including removing old unserviceable item complete all as specified and directed.

LED secruity light fitting of capacity 25 Watt LED street light fitting in aluminium PDC housing, toughened glass cover with IP65 protection with suitable inbuilt surge protector and cable connection from ceiling rose to light fitting and testing and including removing of old unserviceable item complete all as specified and directed.

Sheet metal enclosure double door type for DBs single pole and neutral 12 way 240 V with 200 Amp bus bar including blanking plates where required including fixed flush in wall chases wall for fixing DB and making good surfaces to match with existing surface in repairs all as specified and directed.

MCB SPN 40 to 63 Amps 10 KA,"C" series,AC, 240Volts, 50Hz, ISI marked fixed in repairs complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 600mmX 600mmX 6mm thick buried directly in ground vertically ( earth pit not less than 2.25 meters deep below ground level) with top edge of plate not less than 1.5 metres below ground level, connected to and including galvanised iron wire 4 mm dia and light grade protection pipe of 15 mm dia from earth electrode up to test point or up to 7.5mtr whichever is less by means of GI bolts, nuts, check nuts and washers all as per electrical plate No 3 of SSR Pt-I and GI watering pipe of 20 mm dia medium grade,GI funnel with wire mesh,including charcoal, salt packed all around the earth electrode plate in layers, PCC earth pit chamber 1:3:6 type C1, of size 45X 45X 45 CM,RCC cover 1:2:4 type B1 of size 45X45X6 CM with Reinforcement bars of 8mm dia @120mm c/c excavation/earth work in any strata and returning filling, removal of surplus soil and testing/test point for required value including removing old item complete all as specified and directed.

Exhaust fan single phase metal body, AC 230 Volt, 50 Hz, 900 RPM of size 300mm sweep with louvers shutter complete with all accessories including connecting up from ceiling rose complete all as specified and directed. Note: Unsv exhaust fan shall be deposited in MES store Yard

Sub main wiring complete with 2 runs of 6 sqmm single core copper conductor (ISI marked)cable 1100 volts grade,FRLSH type, PVC insulated, unsheathed,flexible,multi stranded colour coded cables drawn through rigid PVC conduit of size 25 mm dia medium grade(MMS) with all connected accessories such as Bend,Tee,Elbow,Short peices etc concealed in wall/roofs/floors and including one run of 6 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade,FRLSH type as earth continuity conductor connected to common earth dolly including making good the disturbed surfaces to match with existing surface including taking down of old existing submain cable complete all as specified and directed. Note : - Two run of 6 sqmm single core copper conductor cable and one run of 6 sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit.

Ceiling fans complete with blades. Down rods, electronic regulator and accessories, 230 volt, 1200mm sweep, min air delivery 210 CFM with service value 6 BEE five star rated with brushless direct current motor (BLDC) incl taking down existing and deposit with MES all as specified and directed. Note- Usvc and old items shall be deposited to MES yard store

Vertical double door enclosure factory made TPN in replacement fitted with bus bar neutral link, blanking plates of 4 way (4+12) with suitable for incomming MCCB 4 pole 'I/C' frame,having isolated neutral bar, mechanical impact strength IK09, door earthing suitable for MCCB upto 125 Amp, complete all as specified and as directed

MCCB 04 pole 415 volts 16 KA, 63 Amp adjustable thermal & fixed magnetic setting type suitable for TPN vertical loadline DB fixed in replacement, complete all as specified and as directed.

Supply and fixing electric water heater, storage type steel body with steel inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece incl making holes on walls for proper fixing with nuts and bolts complete making the surface good as per existing all as specified and directed. Note: Old unsv geyser shall be deposited in MES store yard.

Supply and testing XLPE cable insulated, armoured, earthed, heavy duty electric cable with aluminium conductor, 1100 Volt grade, cross sectional area 50 sqmm 4 core including necessary cable lugs, glands, insulation tape etc complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan in depth and getting out etc in any type of soil, complete all as specified and directed.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exc. 25cm, complete all as specified and directed.

Removal of excavated material to a distance not exc 50m and depositing where directed at a level not exceeding 1.5m above the starting point all as specified and directed.

Galvanized iron medium class pipe of 25mm bore including fittings fixed in repairs of complete all as specified and directed.

25mm bore gun metal glove or gate valve with iron wheel head screwed bith end for iron pipe and fixed in repairs, complete all as specified and as directed.

Please Enable Macros to View BoQ information