Loading…
Loading…
Tender Value
₹4.5 Cr
EMD Value
₹9.1 L
Closing Date
10 Jun 2026, 2:00 pm4d left
SC-KZJ Section: Design, Manufacturing, Laying and Supply of diamond crossing (two obtuse and acute crossings) in connection with yard improvement at KZJ yard.
55_CR_SC_26_OT
55_CR_SC_26_OT
Open
12 Months
Unknown (Unspecified Location)
₹0
₹9.1 L
19 May 2026
19 May 2026
27 May 2026
Item Breakup - A-Schedule-A
Each SECUNDERABAD DIVISION-ENGG/SOUTH CENTRAL RLY Laying and linking all types of turnouts, diamond crossings and Derailing switches with 52Kg / 60Kg rail section on PSC sleepers on ballast bed, prepared after dismantling & removal of existing turnout/normal line during TTR/yard remodeling under traffic block, as per standard drawing, duly leading sleepers, rails, switches, crossings, fastenings including rail cutting, drilling, fixing of all components, fittings with housing of tongue rails as per requirement of signaling, preparing ballast bed, filling and spreading of ballast as required, linking of turnout with track, attending track parameters including lifting, providing one round of packing to make track fit for 20 kmph speed including lubrication of fittings/fastening, complete as directed by Engineer in-charge. Note: Payment for dismantling & removal of existing turnout/normal line, transportation/stacking of released material and preparing of ballast bed is not included in this item and shall be paid under relevant item.
Set Lifting for increase in ballast cushion of existing points & crossing layouts up to 75mm or part thereof including approach and exit sleepers including one round of through packing, correcting the disturbed sleeper spacing, tightening of fittings, boxing of ballast and ramping out on either side at slope not steeper than 1 in 1000 or as directed. Note: Item will be paid only when lifting is 50mm or more.
Set Manual deep screening of Plain track/ turnouts as per procedure prescribed in IRPWM, June 2020 or latest, on PSC sleepers of any density and throwing away screened muck arising out of screening on toe of bank or on cess, if low or on spoil banks above top of cutting (including throwing and leveling, if required beyond minimum 5m from the edge of cutting which are up to 3m deep or alternatively carting it up to 50m for disposing it off beyond cutting or platforms) as per direction of Engineer in-charge, including cutting cess for effective drainage on both sides, one round of kutcha packing with screened ballast and further attending to track parameter to make track fit for 20 kmph speed complete in all respect. Note : Payment shall be made for length along main line only for turnouts.
887.70 Turnouts Quick cutting with abrasive rail cutter of all types of rail sections including wear resistant, head hardened rails up to 110 UTS, with contractors tools & plants, equipment, consumable with all lead & lift etc. complete as directed by Engineer in-charge. Abrasive Rail Cutter will be as per RDSO Specification No. TM/SM/1 (Rev. 01 of 2012) with latest status of RDSO; Rail Cutting Wheel Abrasive Disc will be as per RDSO Specification No.TM/SM/2 (Rev. 01 of 2020)
Each SECUNDERABAD DIVISION-ENGG/SOUTH CENTRAL RLY Drilling holes of 16 mm to 32 mm dia. with Rail Drilling machine including chamfering with appropriate chamfering tools in all types of rail section with contractor's tools & plants, equipment, consumable with all lead & lift etc. complete, as directed by Engineer in-charge. Rail Drilling Machine will be as per RDSO Specification No. TM/SM/3, dated 24.04.1991.
Item Breakup - B-Schedule-B
Design, Manufacturing, Supply standard diamond crossings (two obtuse and acute crossings) includes CMS crossing with FBW welded legs , check rails, special cast steel base plates (G20Mn5) for diamond area, fastening and pads diamond area, Manufacturing and supply of PSC sleepers set for the Diamond crossing. Scope excludes: Lead rails and fastening for lead portion and standard base plates, Switch machine, setting rod and detector rod, locking devices / signalling equipment insulating joint, normal crossing and switches. NOTE: (1). Design and Drawing includess complaince to RDSO/South Central Railway observations and Final drawing approval. (2) . laying of Diamond crossing shall be paid seperately . (3). Transportation shall not be paid seperately. Total 44250000.00
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Mastertenderbooklet2ason26.03.2026.pdf
ATTACHMENT
Mastertenderbooklet1ason26.03.2026.pdf
ATTACHMENT
REVISEDTRACKCONDITIONS25.03.2023.pdf
ATTACHMENT
SpecialConditionsforDesignManufacturingtobeloaded.pdf Special conditions diamond
ATTACHMENT
particularsoftheworkdiamond.pdf
ATTACHMENT
SpecialConditionsforDesignManufacturingtobeloaded.pdf
ATTACHMENT
Download all tender documents and submit your bid