Periodical services to certain Bldgs in ILP / KLP units including over head tanks AGE B/R-II at Suratgarh Mil Stn

Amount

Taking down cement plaster or cement lime plaster on stone surface/brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-charge.

Supply only integral water proofing compound (ISI marked) complete all as specified and directed by Engineer-in-charge.

M&L for 15mm thick rendering in two layer on fair faces of brick masonry or concrete surfaces of walls consisting of 1st layer of 10mm thick plaster in CM 1:6 and 2nd layer (setting coat or top layer) of 5 mm thick plaster in CM 1:4 mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished fair & even, complete, all as specified. Note : - Supply only water proofing compound shall be measured and paid for separately.

M&L for 10mm thick rendering in cement mortar (1:6) on fair faced surface of brick masonary or concrete surface of walls, finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for rough cast finish plaster with a mixture consisting of crushed stone or fine gravel aggregate mixed with coarse sand and cement in the ratio of 1:1:1 over & including 12mm thick rendering in cement mortar 1:3 on fair faces of brick masonry or concrete surfaces of walls complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surface of walls & applying two coats of cement base paint of approved shade/tint over a coat of cement base primer and filling cement based putty in cracks complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old decorated, plastered or pointed surfaces of ceiling by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots, filling cracks with wall care putty etc and applying one coat of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying one coat of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old decorated, plastered or pointed surfaces of ceiling by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying two coat of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying two coat of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for complete removal of existing treatment from old plastered surfaces of wall, preparation of surfaces including filling of cracks and applying three coats of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for complete removal of existing treatment from old plastered surfaces of ceiling, preparation of surfaces including filling of cracks and applying three coats of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots, washing, rubbing down and stopping of distempered surface, filling of cracks etc and applying one coat of oil bound distemper complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots, washing, rubbing down and stopping of distempered surface, filling of cracks etc and applying one coat of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company depot tinted) with silicon additives @ 1.43 litre / 10 sqm complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots, washing, rubbing down and stopping of distempered surface, filling of cracks etc and applying two coat of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company depot tinted) with silicon additives @ 1.43 litre / 10 sqm complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots, washing, rubbing down and stopping of distempered surface etc and applying two coat of distemper oil emulsion complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of new plastered and unplastered surfaces of wall and applying two coats of oil bound distemper including Alkali resistant priming preparatory to distempering complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of new plastered and unplastered surfaces of wall and applying two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company depot tinted) with silicon additives @ 1.43 litre / 10 sqm over and including one coat of primer applied @ 0.9 litre / 10sqm as per manufacturer instruction complete all as specified & directed by Engineer-in-Charge.

M&L for complete removal of existing treatment from old plastered surfaces like lime, distemper, plastic paint, cement base paint including scrapping down smoke soot, moulds, moss, efflorscent salts, trading oil, greasy spots using mechanical grinding machine and washing of old surface with water of wall, preparation of surfaces and applying two coats of oil bound distemper (OBD) over a coat of appropirate primer over and including 1mm thick layer of wall putty (Make J K or Birla) complete all as specified & directed by Engineer-in-Charge.

M&L for complete removal of existing treatment from old plastered surfaces of wall by vaccume based sanding machine, removal of nails etc & filling cracks/ hole with putty and finally washing with watering and applying two coat of exterior emulsion weather proof antifungal paint over a coat of exterior grade primer by roller of air spray complete all as specified and directed by Engineer-in-charge. Note :- After complete removal of existing treatment surfaces shall be inspected by the Engineer-in-Charge and further each coat of exterior paint and primer shall be applied only after passed by Engineer-in-Charge.

M&L for complete removal of existing treatment from old plastered surfaces of RCC over head water tank of capacity 0.50 Lakh Gallons (approximte area 550 Sqm), preparation of surfaces including filling of cracks and two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company depot tinted) with silicon additives @ 1.43 litre / 10 sqm over and including one coat of primer applied @ 0.9 litre / 10sqm as per manufacturer instruction complete all as specified & directed by Engineer-in-Charge. Note :- After complete removal of existing treatment surfaces shall be inspected by the Engineer-in-Charge and further each coat of exterior paint and primer shall be applied only after passed by Engineer-in-Charge.

M&L for complete removal of existing treatment from old plastered surfaces of RCC over head water tank of capacity 1.00 Lakh Gallons (approximte area 920 Sqm), preparation of surfaces including filling of cracks and two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company depot tinted) with silicon additives @ 1.43 litre / 10 sqm over and including one coat of primer applied @ 0.9 litre / 10sqm as per manufacturer instruction complete all as specified & directed by Engineer-in-Charge. Note :- After complete removal of existing treatment surfaces shall be inspected by the Engineer-in-Charge and further each coat of exterior paint and primer shall be applied only after passed by Engineer-in-Charge.

M&L for complete removal of existing treatment from old plastered surfaces like lime, distemper, plastic paint, cement base paint including scrapping down smoke soot, moulds, moss, efflorscent salts, trading oil, greasy spots using mechanical grinding machine and washing of old surface with water including filling of cracks and applying two coats of cement base paint shade/tint over a coat of cement base primer on walls complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing,scrapping down smoke soot mulds, moss and efflorescent, salts, filling of cracks etc and applying a coat of cement based paint complete all as specified & directed by Engineer-in-Charge.

M&L for complete removal of existing treatment including preparation of surfaces and applying two coat of texture paint (3.28 ltr/10 sqm per coat) on walls over a coat of appropriate primer (2.20 ltr/10 sqm) complete all as specified & directed by Engineer-in-Charge. Note :- After complete removal of existing treatment surfaces shall be inspected by the Engineer-in-Charge and further each coat of exterior paint and primer shall be applied only after passed by Engineer-in-Charge.

M&L for preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing,scrapping down smoke soot mulds, moss and efflorescent, salts etc and applying two coat of cement based paint complete all as specified & directed by Engineer-in-Charge.

M&L for writing letters or figures (Block. Roman, Italic or Indian) not exceding 30 cm high complete all as specified and directed by Engineer-in-Charge.

M&L for Stops, commas, short lines, dashes, hyphens, brackets, etc. complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of approved tint complete all as specified and directed by Engineer-in-charge.

M&L for removing loose ceiling plaster completely, cleaning and dripping mortars and curing of effected surface area, cleaning well expossed reinforcement and applying two coats of anti-corrosive paint to it, supply and fixing mild steel XPM mesh of size 25mm x 25mm (wire dia min. 2mm) to the effected ceiling surface either by welding with exposed reinforcement or by stapling nails or screw or tie with reinforcement, applying cement slury and 25mm thick microphone of 1:1:1 using 6mm graded aggregate and cuting it for 3 days and then making well finish the surface using cement mortar 1:3 complete all as specified and directed by Engineer-in-charge.

HARPREET SINGH CONTRACTOR

M/s JUGAL KISHORE MISHRA AND SONS

S.K BUILDERS AND ENGINEERS

AK CONSTRUCTION

M/S Shree Ram Enterprises

BISHNOI BUILDERS

godara construction company